Linux CXL
 help / color / mirror / Atom feed
From: Dave Jiang <dave.jiang@intel.com>
To: Robert Richter <rrichter@amd.com>,
	Alison Schofield <alison.schofield@intel.com>,
	Vishal Verma <vishal.l.verma@intel.com>,
	Ira Weiny <ira.weiny@intel.com>,
	Ben Widawsky <bwidawsk@kernel.org>,
	Dan Williams <dan.j.williams@intel.com>
Cc: Jonathan Cameron <jonathan.cameron@huawei.com>,
	linux-cxl@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: Re: [PATCH v4] cxl/mbox: Fix Payload Length check for Get Log command
Date: Tue, 24 Jan 2023 09:31:53 -0700	[thread overview]
Message-ID: <83d6db31-c75c-6d0f-0b31-7cd12a6816ae@intel.com> (raw)
In-Reply-To: <20230119094934.86067-1-rrichter@amd.com>



On 1/19/23 2:49 AM, Robert Richter wrote:
> Commit 2aeaf663b85e introduced strict checking for variable length
> payload size validation. The payload length of received data must
> match the size of the requested data by the caller except for the case
> where the min_out value is set.
> 
> The Get Log command does not have a header with a length field set.
> The Log size is determined by the Get Supported Logs command (CXL 3.0,
> 8.2.9.5.1). However, the actual size can be smaller and the number of
> valid bytes in the payload output must be determined reading the
> Payload Length field (CXL 3.0, Table 8-36, Note 2).
> 
> Two issues arise: The command can successfully complete with a payload
> length of zero. And, the valid payload length must then also be
> consumed by the caller.
> 
> Change cxl_xfer_log() to pass the number of payload bytes back to the
> caller to determine the number of log entries. Implement the payload
> handling as a special case where mbox_cmd->size_out is consulted when
> cxl_internal_send_cmd() returns -EIO. A WARN_ONCE() is added to check
> that -EIO is only returned in case of an unexpected output size.
> 
> Logs can be bigger than the maximum payload length and multiple Get
> Log commands can be issued. If the received payload size is smaller
> than the maximum payload size we can assume all valid bytes have been
> fetched. Stop sending further Get Log commands then.
> 
> On that occasion, change debug messages to also report the opcodes of
> supported commands.
> 
> The variable payload commands GET_LSA and SET_LSA are not affected by
> this strict check: SET_LSA cannot be broken because SET_LSA does not
> return an output payload, and GET_LSA never expects short reads.
> 
> Fixes: 2aeaf663b85e ("cxl/mbox: Add variable output size validation for internal commands")
> Signed-off-by: Robert Richter <rrichter@amd.com>

Reviewed-by: Dave Jiang <dave.jiang@intel.com>

> ---
> v4:
>   * Fixed a build issue.
> v3:
>   * Added comment to the WARN_ONCE(). (Jonathan)
>   * Passing a size pointer to report the payload size back. (Jonathan)
>   * Moved logging of supported opcodes out of this patch for a separate
>     change. (Jonathan)
> 
>   drivers/cxl/core/mbox.c | 25 ++++++++++++++++++++++---
>   1 file changed, 22 insertions(+), 3 deletions(-)
> 
> diff --git a/drivers/cxl/core/mbox.c b/drivers/cxl/core/mbox.c
> index b03fba212799..a48ade466d6a 100644
> --- a/drivers/cxl/core/mbox.c
> +++ b/drivers/cxl/core/mbox.c
> @@ -170,6 +170,12 @@ int cxl_internal_send_cmd(struct cxl_dev_state *cxlds,
>   	out_size = mbox_cmd->size_out;
>   	min_out = mbox_cmd->min_out;
>   	rc = cxlds->mbox_send(cxlds, mbox_cmd);
> +	/*
> +	 * EIO is reserved for a payload size mismatch and mbox_send()
> +	 * may not return this error.
> +	 */
> +	if (WARN_ONCE(rc == -EIO, "Bad return code: -EIO"))
> +		return -ENXIO;
>   	if (rc)
>   		return rc;
>   
> @@ -550,9 +556,9 @@ int cxl_send_cmd(struct cxl_memdev *cxlmd, struct cxl_send_command __user *s)
>   	return 0;
>   }
>   
> -static int cxl_xfer_log(struct cxl_dev_state *cxlds, uuid_t *uuid, u32 size, u8 *out)
> +static int cxl_xfer_log(struct cxl_dev_state *cxlds, uuid_t *uuid, u32 *size, u8 *out)
>   {
> -	u32 remaining = size;
> +	u32 remaining = *size;
>   	u32 offset = 0;
>   
>   	while (remaining) {
> @@ -576,6 +582,17 @@ static int cxl_xfer_log(struct cxl_dev_state *cxlds, uuid_t *uuid, u32 size, u8
>   		};
>   
>   		rc = cxl_internal_send_cmd(cxlds, &mbox_cmd);
> +
> +		/*
> +		 * The output payload length that indicates the number
> +		 * of valid bytes can be smaller than the Log buffer
> +		 * size.
> +		 */
> +		if (rc == -EIO && mbox_cmd.size_out < xfer_size) {
> +			offset += mbox_cmd.size_out;
> +			break;
> +		}
> +
>   		if (rc < 0)
>   			return rc;
>   
> @@ -584,6 +601,8 @@ static int cxl_xfer_log(struct cxl_dev_state *cxlds, uuid_t *uuid, u32 size, u8
>   		offset += xfer_size;
>   	}
>   
> +	*size = offset;
> +
>   	return 0;
>   }
>   
> @@ -694,7 +713,7 @@ int cxl_enumerate_cmds(struct cxl_dev_state *cxlds)
>   			goto out;
>   		}
>   
> -		rc = cxl_xfer_log(cxlds, &uuid, size, log);
> +		rc = cxl_xfer_log(cxlds, &uuid, &size, log);
>   		if (rc) {
>   			kvfree(log);
>   			goto out;
> 
> base-commit: 1b929c02afd37871d5afb9d498426f83432e71c2

  parent reply	other threads:[~2023-01-24 16:32 UTC|newest]

Thread overview: 5+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2023-01-19  9:49 [PATCH v4] cxl/mbox: Fix Payload Length check for Get Log command Robert Richter
2023-01-24  9:34 ` Jonathan Cameron
2023-01-24 16:31 ` Dave Jiang [this message]
2023-01-27 19:48 ` Dan Williams
2023-01-27 20:59   ` Robert Richter

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=83d6db31-c75c-6d0f-0b31-7cd12a6816ae@intel.com \
    --to=dave.jiang@intel.com \
    --cc=alison.schofield@intel.com \
    --cc=bwidawsk@kernel.org \
    --cc=dan.j.williams@intel.com \
    --cc=ira.weiny@intel.com \
    --cc=jonathan.cameron@huawei.com \
    --cc=linux-cxl@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=rrichter@amd.com \
    --cc=vishal.l.verma@intel.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox