Re: [PATCH v2 2/3] Bluetooth: hci_uart: Add support for Amlogic HCI UART

[Krzysztof Kozlowski <krzk@kernel.org>]

On 18/07/2024 09:42, Yang Li via B4 Relay wrote:
> From: Yang Li <yang.li@amlogic.com>
> 
> This patch introduces support for Amlogic Bluetooth controller over
> UART. In order to send the final firmware at full speed. It is a pretty
> straight forward H4 driver with exception of actually having it's own
> setup address configuration.
> 

...

> +static int aml_parse_dt(struct aml_serdev *amldev)
> +{
> +	struct device *pdev = amldev->dev;
> +
> +	amldev->bt_en_gpio = devm_gpiod_get(pdev, "bt-enable",
> +					GPIOD_OUT_LOW);
> +	if (IS_ERR(amldev->bt_en_gpio)) {
> +		dev_err(pdev, "Failed to acquire bt-enable gpios");
> +		return PTR_ERR(amldev->bt_en_gpio);
> +	}
> +
> +	if (device_property_read_string(pdev, "firmware-name",
> +					&amldev->firmware_name)) {
> +		dev_err(pdev, "Failed to acquire firmware path");
> +		return -ENODEV;
> +	}
> +
> +	amldev->bt_supply = devm_regulator_get(pdev, "bt");
> +	if (IS_ERR(amldev->bt_supply)) {
> +		dev_err(pdev, "Failed to acquire regulator");
> +		return PTR_ERR(amldev->bt_supply);
> +	}
> +
> +	amldev->lpo_clk = devm_clk_get(pdev, NULL);
> +	if (IS_ERR(amldev->lpo_clk)) {
> +		dev_err(pdev, "Failed to acquire clock source");
> +		return PTR_ERR(amldev->lpo_clk);
> +	}
> +
> +	/* get rf config parameter */
> +	if (device_property_read_u32(pdev, "antenna-number",
> +				&amldev->ant_number)) {
> +		dev_info(pdev, "No antenna-number, using default value");
> +		amldev->ant_number = 1;
> +	}
> +
> +	return 0;
> +}
> +
> +static int aml_power_on(struct aml_serdev *amldev)
> +{
> +	int err;
> +
> +	if (!IS_ERR(amldev->bt_supply)) {

How is IS_ERR possible?

> +		err = regulator_enable(amldev->bt_supply);
> +		if (err) {
> +			dev_err(amldev->dev, "Failed to enable regulator: (%d)", err);
> +			return err;
> +		}
> +	}
> +
> +	if (!IS_ERR(amldev->lpo_clk)) {

How is IS_ERR possible?

> +		err = clk_prepare_enable(amldev->lpo_clk);
> +		if (err) {
> +			dev_err(amldev->dev, "Failed to enable lpo clock: (%d)", err);
> +			return err;
> +		}
> +	}
> +
> +	if (!IS_ERR(amldev->bt_en_gpio))

How is IS_ERR possible?

> +		gpiod_set_value_cansleep(amldev->bt_en_gpio, 1);
> +
> +	/* wait 100ms for bluetooth controller power on  */
> +	msleep(100);
> +	return 0;
> +}


Best regards,
Krzysztof