[PATCH 1/3] ARM: dts: rockchip: Add support for phyCORE-RK3288 SoM

[PATCH 1/3] ARM: dts: rockchip: Add support for phyCORE-RK3288 SoM

[Wadim Egorov]

The phyCORE-RK3288 is a SoM (System on Module) containing a RK3288 SoC.
The module can be connected to different carrier boards.
It can be also equipped with different RAM, SPI flash and eMMC variants.
The Rapid Development Kit option is using the following setup:

  - 1 GB DDR3 RAM (2 Banks)
  - 1x 4 KB EEPROM
  - DP83867 Gigabit Ethernet PHY
  - 16 MB SPI Flash
  - 4 GB eMMC Flash

Signed-off-by: Wadim Egorov <w.egorov-guT5V/WYfQezQB+pC5nmwQ@public.gmane.org>
---
 arch/arm/boot/dts/rk3288-phycore-som.dtsi | 463 ++++++++++++++++++++++++++++++
 1 file changed, 463 insertions(+)
 create mode 100644 arch/arm/boot/dts/rk3288-phycore-som.dtsi

diff --git a/arch/arm/boot/dts/rk3288-phycore-som.dtsi b/arch/arm/boot/dts/rk3288-phycore-som.dtsi
new file mode 100644
index 0000000..36e690e
--- /dev/null
+++ b/arch/arm/boot/dts/rk3288-phycore-som.dtsi
@@ -0,0 +1,463 @@
+/*
+ * Copyright (C) 2017 PHYTEC Messtechnik GmbH
+ * Author: Wadim Egorov <w.egorov-guT5V/WYfQezQB+pC5nmwQ@public.gmane.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <dt-bindings/net/ti-dp83867.h>
+#include "rk3288.dtsi"
+
+/ {
+	model = "Phytec RK3288 phyCORE";
+	compatible = "phytec,rk3288-phycore-som", "rockchip,rk3288";
+
+	/*
+	 * Set the minimum memory size here and
+	 * let the bootloader set the real size.
+	 */
+	memory {
+		device_type = "memory";
+		reg = <0 0x8000000>;
+	};
+
+	aliases {
+		rtc0 = &i2c_rtc;
+		rtc1 = &rk818;
+	};
+
+	ext_gmac: external-gmac-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <125000000>;
+		clock-output-names = "ext_gmac";
+	};
+
+	leds: user-leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&user_led>;
+
+		user {
+			label = "green_led";
+			gpios = <&gpio7 2 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			default-state = "keep";
+		};
+	};
+
+	vdd_emmc_io: vdd-emmc-io {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_emmc_io";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vdd_3v3_io>;
+	};
+
+	vdd_in_otg_out: vdd-in-otg-out {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_in_otg_out";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	vdd_misc_1v8: vdd-misc-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_misc_1v8";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+};
+
+&cpu0 {
+	cpu0-supply = <&vdd_cpu>;
+	operating-points = <
+		/* KHz    uV */
+		1800000	1400000
+		1608000	1350000
+		1512000 1300000
+		1416000 1200000
+		1200000 1100000
+		1008000 1050000
+		 816000 1000000
+		 696000  950000
+		 600000  900000
+		 408000  900000
+		 312000  900000
+		 216000  900000
+		 126000  900000
+	>;
+};
+
+&emmc {
+	status = "okay";
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	disable-wp;
+	non-removable;
+	num-slots = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_pwr &emmc_bus8>;
+	vmmc-supply = <&vdd_3v3_io>;
+	vqmmc-supply = <&vdd_emmc_io>;
+};
+
+&gmac {
+	assigned-clocks = <&cru SCLK_MAC>;
+	assigned-clock-parents = <&ext_gmac>;
+	clock_in_out = "input";
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii_pins &phy_rst &phy_int>;
+	phy-supply = <&vdd_eth_2v5>;
+	phy-mode = "rgmii-id";
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 10000 1000000>;
+	snps,reset-gpio = <&gpio4 8 GPIO_ACTIVE_HIGH>;
+	tx_delay = <0x0>;
+	rx_delay = <0x0>;
+	phy-handle = <&phy0>;
+
+	mdio0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+
+		phy0: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			interrupt-parent = <&gpio4>;
+			interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+			ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+			ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+			ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+			enet-phy-lane-no-swap;
+		};
+	};
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c5>;
+};
+
+&io_domains {
+	rockchip,grf = <&grf>;
+	sdcard-supply = <&vdd_io_sd>;
+	flash0-supply = <&vdd_emmc_io>;
+	flash1-supply = <&vdd_misc_1v8>;
+	gpio1830-supply = <&vdd_3v3_io>;
+	gpio30-supply = <&vdd_3v3_io>;
+	bb-supply = <&vdd_3v3_io>;
+	dvp-supply = <&vdd_3v3_io>;
+	lcdc-supply = <&vdd_3v3_io>;
+	wifi-supply = <&vdd_3v3_io>;
+	audio-supply = <&vdd_3v3_io>;
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	rk818: pmic@1c {
+		compatible = "rockchip,rk818";
+		reg = <0x1c>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int>;
+		rockchip,system-power-controller;
+		wakeup-source;
+		#clock-cells = <1>;
+
+		vcc1-supply = <&vdd_sys>;
+		vcc2-supply = <&vdd_sys>;
+		vcc3-supply = <&vdd_sys>;
+		vcc4-supply = <&vdd_sys>;
+		boost-supply = <&vdd_in_otg_out>;
+		vcc6-supply = <&vdd_sys>;
+		vcc7-supply = <&vdd_misc_1v8>;
+		vcc8-supply = <&vdd_misc_1v8>;
+		vcc9-supply = <&vdd_3v3_io>;
+		vddio-supply = <&vdd_3v3_io>;
+
+		regulators {
+			vdd_log: DCDC_REG1 {
+				regulator-name = "vdd_log";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_gpu: DCDC_REG2 {
+				regulator-name = "vdd_gpu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1250000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1000000>;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-name = "vcc_ddr";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vdd_3v3_io: DCDC_REG4 {
+				regulator-name = "vdd_3v3_io";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vdd_sys: DCDC_BOOST {
+				regulator-name = "vdd_sys";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5000000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <5000000>;
+				};
+			};
+
+			/* vcc9 */
+			vdd_sd: SWITCH_REG {
+				regulator-name = "vdd_sd";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			/* vcc6 */
+			vdd_eth_2v5: LDO_REG2 {
+				regulator-name = "vdd_eth_2v5";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <2500000>;
+				regulator-max-microvolt = <2500000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <2500000>;
+				};
+			};
+
+			/* vcc7 */
+			vdd_1v0: LDO_REG3 {
+				regulator-name = "vdd_1v0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1000000>;
+				};
+			};
+
+			/* vcc8 */
+			vdd_1v8_lcd_ldo: LDO_REG4 {
+				regulator-name = "vdd_1v8_lcd_ldo";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			/* vcc8 */
+			vdd_1v0_lcd: LDO_REG6 {
+				regulator-name = "vdd_1v0_lcd";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1000000>;
+				};
+			};
+
+			/* vcc7 */
+			vdd_1v8_ldo: LDO_REG7 {
+				regulator-name = "vdd_1v8_ldo";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			/* vcc9 */
+			vdd_io_sd: LDO_REG9 {
+				regulator-name = "vdd_io_sd";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+		};
+	};
+
+	/* M24C32-D */
+	i2c_eeprom: eeprom@50 {
+		compatible = "atmel,24c32";
+		reg = <0x50>;
+		pagesize = <32>;
+	};
+
+	vdd_cpu: fan53555@60 {
+		compatible = "fcs,fan53555";
+		reg = <0x60>;
+		fcs,suspend-voltage-selector = <1>;
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-enable-ramp-delay = <300>;
+		regulator-name = "vdd_cpu";
+		regulator-min-microvolt = <800000>;
+		regulator-max-microvolt = <1430000>;
+		regulator-ramp-delay = <8000>;
+		vin-supply = <&vdd_sys>;
+	};
+};
+
+&pinctrl {
+	pcfg_output_high: pcfg-output-high {
+		output-high;
+	};
+
+	emmc {
+		/*
+		 * We run eMMC at max speed; bump up drive strength.
+		 * We also have external pulls, so disable the internal ones.
+		 */
+		emmc_clk: emmc-clk {
+			rockchip,pins = <3 18 RK_FUNC_2 &pcfg_pull_none_12ma>;
+		};
+
+		emmc_cmd: emmc-cmd {
+			rockchip,pins = <3 16 RK_FUNC_2 &pcfg_pull_none_12ma>;
+		};
+
+		emmc_bus8: emmc-bus8 {
+			rockchip,pins = <3 0 RK_FUNC_2 &pcfg_pull_none_12ma>,
+					<3 1 RK_FUNC_2 &pcfg_pull_none_12ma>,
+					<3 2 RK_FUNC_2 &pcfg_pull_none_12ma>,
+					<3 3 RK_FUNC_2 &pcfg_pull_none_12ma>,
+					<3 4 RK_FUNC_2 &pcfg_pull_none_12ma>,
+					<3 5 RK_FUNC_2 &pcfg_pull_none_12ma>,
+					<3 6 RK_FUNC_2 &pcfg_pull_none_12ma>,
+					<3 7 RK_FUNC_2 &pcfg_pull_none_12ma>;
+		};
+	};
+
+	gmac {
+		phy_int: phy-int {
+			rockchip,pins = <4 2 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+
+		phy_rst: phy-rst {
+			rockchip,pins = <4 8 RK_FUNC_GPIO &pcfg_output_high>;
+		};
+	};
+
+	leds {
+		user_led: user-led {
+			rockchip,pins = <7 2 RK_FUNC_GPIO &pcfg_output_high>;
+		};
+	};
+
+	pmic {
+		pmic_int: pmic-int {
+			rockchip,pins = <RK_GPIO0 4 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+
+		/* Pin for switching state between sleep and non-sleep state */
+		pmic_sleep: pmic-sleep {
+			rockchip,pins = <RK_GPIO0 0 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+};
+
+&pwm1 {
+	status = "okay";
+};
+
+&saradc {
+	status = "okay";
+	vref-supply = <&vdd_1v8_ldo>;
+};
+
+&spi2 {
+	status = "okay";
+
+	serial_flash: m25p80@0 {
+		compatible = "micron,n25q128a13", "jedec,spi-nor";
+		reg = <0x0>;
+		spi-max-frequency = <50000000>;
+		m25p,fast-read;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		status = "okay";
+	};
+};
+
+&tsadc {
+	status = "okay";
+	rockchip,hw-tshut-mode = <0>;
+	rockchip,hw-tshut-polarity = <0>;
+};
+
+&vopb {
+	status = "okay";
+};
+
+&vopb_mmu {
+	status = "okay";
+};
+
+&vopl {
+	status = "okay";
+};
+
+&vopl_mmu {
+	status = "okay";
+};
+
+&wdt {
+	status = "okay";
+};
-- 
1.9.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 2/3] ARM: dts: rockchip: Add support for PCM-947 carrier board

[Wadim Egorov]

Add basic support for the PCM-947 carrier board, a RK3288 based development
board made by PHYTEC. This board works in a combination with
the phyCORE-RK3288 System on Module.

Following interfaces and devices are available on the PCM-947 carrier board:

  - 2x UART
  - micro SDMMC
  - USB host and USB otg
  - USB 3503 HSIC hub
  - Ethernet
  - 2nd alternative KSZ9031 ethernet phy
  - Display connectors: PHYTEC LVDS, DDG LVDS, parallel signals, HDMI
  - Parallel Camera CIF
  - SGTL5000-32QFN audio codec
  - 4x LEDs connected via PCA9533
  - 2 user buttons
  - Expansion connectors for WiFi and other modules
  - RTC RV-4162-C7
  - Resistive touch STMPE811
  - EEPROM M24C32

Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
---
 arch/arm/boot/dts/Makefile               |   1 +
 arch/arm/boot/dts/rk3288-phycore-rdk.dts | 263 +++++++++++++++++++++++++++++++
 2 files changed, 264 insertions(+)
 create mode 100644 arch/arm/boot/dts/rk3288-phycore-rdk.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 0118084..8c3cb4d 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -692,6 +692,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += \
 	rk3288-firefly.dtb \
 	rk3288-firefly-reload.dtb \
 	rk3288-miqi.dtb \
+	rk3288-phycore-rdk.dtb \
 	rk3288-popmetal.dtb \
 	rk3288-r89.dtb \
 	rk3288-rock2-square.dtb \
diff --git a/arch/arm/boot/dts/rk3288-phycore-rdk.dts b/arch/arm/boot/dts/rk3288-phycore-rdk.dts
new file mode 100644
index 0000000..16a2b96
--- /dev/null
+++ b/arch/arm/boot/dts/rk3288-phycore-rdk.dts
@@ -0,0 +1,263 @@
+/*
+ * Copyright (C) 2017 PHYTEC Messtechnik GmbH
+ * Author: Wadim Egorov <w.egorov@phytec.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/leds-pca9532.h>
+#include "rk3288-phycore-som.dtsi"
+
+/ {
+	model = "Phytec RK3288 PCM-947";
+	compatible = "phytec,rk3288-pcm-947", "phytec,rk3288-phycore-som", "rockchip,rk3288";
+
+	user_buttons: user-buttons {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&user_button_pins>;
+
+		button@0 {
+			label = "home";
+			linux,code = <KEY_HOME>;
+			gpios = <&gpio8 0 GPIO_ACTIVE_HIGH>;
+			wakeup-source;
+		};
+
+		button@1 {
+			label = "menu";
+			linux,code = <KEY_MENU>;
+			gpios = <&gpio8 3 GPIO_ACTIVE_HIGH>;
+			wakeup-source;
+		};
+	};
+
+	vcc_host0_5v: usb-host0-regulator {
+		compatible = "regulator-fixed";
+		gpio = <&gpio2 13 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&host0_vbus_drv>;
+		regulator-name = "vcc_host0_5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		vin-supply = <&vdd_in_otg_out>;
+	};
+
+	vcc_host1_5v: usb-host1-regulator {
+		compatible = "regulator-fixed";
+		gpio = <&gpio2 0 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&host1_vbus_drv>;
+		regulator-name = "vcc_host1_5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		vin-supply = <&vdd_in_otg_out>;
+	};
+
+	vcc_otg_5v: usb-otg-regulator {
+		compatible = "regulator-fixed";
+		gpio = <&gpio2 12 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&otg_vbus_drv>;
+		regulator-name = "vcc_otg_5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		vin-supply = <&vdd_in_otg_out>;
+	};
+};
+
+&gmac {
+	status = "okay";
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+
+	stmpe@44 {
+		compatible = "st,stmpe811";
+		reg = <0x44>;
+	};
+
+	adc@64 {
+		compatible = "maxim,max1037";
+		reg = <0x64>;
+	};
+
+	i2c_rtc: rtc@68 {
+		compatible = "rv4162";
+		reg = <0x68>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_rtc_int>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <10 0>;
+	};
+};
+
+&i2c3 {
+	status = "okay";
+
+	i2c_eeprom_cb: eeprom@51 {
+		compatible = "atmel,24c32";
+		reg = <0x51>;
+		pagesize = <32>;
+	};
+};
+
+&i2c4 {
+	status = "okay";
+
+	/* PCA9533 - 4-bit LED dimmer */
+	leddim: leddimmer@62 {
+		compatible = "nxp,pca9533";
+		reg = <0x62>;
+
+		led1 {
+			label = "red:user1";
+			linux,default-trigger = "none";
+			type = <PCA9532_TYPE_LED>;
+		};
+
+		led2 {
+			label = "green:user2";
+			linux,default-trigger = "none";
+			type = <PCA9532_TYPE_LED>;
+		};
+
+		led3 {
+			label = "blue:user3";
+			linux,default-trigger = "none";
+			type = <PCA9532_TYPE_LED>;
+		};
+
+		led4 {
+			label = "red:user4";
+			linux,default-trigger = "none";
+			type = <PCA9532_TYPE_LED>;
+		};
+	};
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&pinctrl {
+	pcfg_pull_up_drv_12ma: pcfg-pull-up-drv-12ma {
+		bias-pull-up;
+		drive-strength = <12>;
+	};
+
+	buttons {
+		user_button_pins: user-button-pins {
+			/* button 1 */
+			rockchip,pins = <8 3 RK_FUNC_GPIO &pcfg_pull_up>,
+			/* button 2 */
+					<8 0 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	rv4162 {
+		i2c_rtc_int: i2c-rtc-int {
+			rockchip,pins = <5 10 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	sdmmc {
+		/*
+		 * Default drive strength isn't enough to achieve even
+		 * high-speed mode on pcm-947 board so bump up to 12 mA.
+		 */
+		sdmmc_bus4: sdmmc-bus4 {
+			rockchip,pins = <6 16 RK_FUNC_1 &pcfg_pull_up_drv_12ma>,
+					<6 17 RK_FUNC_1 &pcfg_pull_up_drv_12ma>,
+					<6 18 RK_FUNC_1 &pcfg_pull_up_drv_12ma>,
+					<6 19 RK_FUNC_1 &pcfg_pull_up_drv_12ma>;
+		};
+
+		sdmmc_clk: sdmmc-clk {
+			rockchip,pins = <6 20 RK_FUNC_1 &pcfg_pull_none_12ma>;
+		};
+
+		sdmmc_cmd: sdmmc-cmd {
+			rockchip,pins = <6 21 RK_FUNC_1 &pcfg_pull_up_drv_12ma>;
+		};
+
+		sdmmc_pwr: sdmmc-pwr {
+			rockchip,pins = <7 11 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	touchscreen {
+		ts_irq_pin: ts-irq-pin {
+			rockchip,pins = <5 15 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	usb_host {
+		host0_vbus_drv: host0-vbus-drv {
+			rockchip,pins = <2 13 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		host1_vbus_drv: host1-vbus-drv {
+			rockchip,pins = <2 0 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	usb_otg {
+		otg_vbus_drv: otg-vbus-drv {
+			rockchip,pins = <2 12 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-mmc-highspeed;
+	cap-sd-highspeed;
+	card-detect-delay = <200>;
+	disable-wp;
+	num-slots = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
+	vmmc-supply = <&vdd_io_sd>;
+	vqmmc-supply = <&vdd_io_sd>;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>;
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&usbphy {
+	status = "okay";
+};
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&usb_host1 {
+	status = "okay";
+};
+
+&usb_otg {
+	status = "okay";
+};
-- 
1.9.1

[PATCH 3/3] dt-bindings: Document Phytec phyCORE-RK3288 RDK

[Wadim Egorov]

Add documentation for the PCM-947 carrier board, a RK3288 based
development board made by PHYTEC.

Signed-off-by: Wadim Egorov <w.egorov-guT5V/WYfQezQB+pC5nmwQ@public.gmane.org>
---
 Documentation/devicetree/bindings/arm/rockchip.txt | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt
index cc4ace6..e079a62 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.txt
+++ b/Documentation/devicetree/bindings/arm/rockchip.txt
@@ -103,6 +103,10 @@ Rockchip platforms device tree bindings
     Required root node properties:
       - compatible = "mqmaker,miqi", "rockchip,rk3288";
 
+- Phytec phyCORE-RK3288: Rapid Development Kit
+    Required root node properties:
+     - compatible = "phytec,rk3288-pcm-947", "phytec,rk3288-phycore-som", "rockchip,rk3288";
+
 - Rockchip PX3 Evaluation board:
     Required root node properties:
       - compatible = "rockchip,px3-evb", "rockchip,px3", "rockchip,rk3188";
-- 
1.9.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH 1/3] ARM: dts: rockchip: Add support for phyCORE-RK3288 SoM

[Heiko Stuebner]

Am Montag, 3. April 2017, 12:23:03 CEST schrieb Wadim Egorov:
> The phyCORE-RK3288 is a SoM (System on Module) containing a RK3288 SoC.
> The module can be connected to different carrier boards.
> It can be also equipped with different RAM, SPI flash and eMMC variants.
> The Rapid Development Kit option is using the following setup:
> 
>   - 1 GB DDR3 RAM (2 Banks)
>   - 1x 4 KB EEPROM
>   - DP83867 Gigabit Ethernet PHY
>   - 16 MB SPI Flash
>   - 4 GB eMMC Flash
> 
> Signed-off-by: Wadim Egorov <w.egorov@phytec.de>

applied for 4.12 with the following minor changes:

- moved phy-handle property up a bit
- switches compatible and #address+#size-cells in mdio0
- dropped rockchip,grf from &io_domains (grf is a simple-mfd and can
  get the grf syscon on its own via its parent)
- vdd_cpu: regulator@60 (from fan53555@60)
- serial_flash: flash@0 (from m25p80@0)
  Nodes should be named after their "category" not the actual device

Thanks
Heiko

Re: [PATCH 1/3] ARM: dts: rockchip: Add support for phyCORE-RK3288 SoM

[Heiko Stübner]

Am Donnerstag, 6. April 2017, 10:30:46 CEST schrieb Heiko Stuebner:
> Am Montag, 3. April 2017, 12:23:03 CEST schrieb Wadim Egorov:
> > The phyCORE-RK3288 is a SoM (System on Module) containing a RK3288 SoC.
> > The module can be connected to different carrier boards.
> > It can be also equipped with different RAM, SPI flash and eMMC variants.
> > 
> > The Rapid Development Kit option is using the following setup:
> >   - 1 GB DDR3 RAM (2 Banks)
> >   - 1x 4 KB EEPROM
> >   - DP83867 Gigabit Ethernet PHY
> >   - 16 MB SPI Flash
> >   - 4 GB eMMC Flash
> > 
> > Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
> 
> applied for 4.12 with the following minor changes:

had to unapply again ... can you please check the license of the files

They're currently GPL2-only, while we use a combined GPL+X11 license
everywhere else. See every other Rockchip dts (and even most other
socs) for reference.

Thanks
Heiko