From: Roland Stigge <stigge-uj/7R2tJ6VmzQB+pC5nmwQ@public.gmane.org>
To: grant.likely-s3s/WqlpOiPyB63q8FvJNQ@public.gmane.org,
arm-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org,
linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org,
linus.walleij-0IS4wlFg1OjSUeElwK9/Pw@public.gmane.org,
kevin.wells-3arQi8VN3Tc@public.gmane.org,
srinivas.bakki-3arQi8VN3Tc@public.gmane.org,
devicetree-discuss-uLR06cmDAlY/bJ5BZ2RsiQ@public.gmane.org,
rob.herring-bsGFqQB8/DxBDgjK7y7TUQ@public.gmane.org
Cc: Roland Stigge <stigge-uj/7R2tJ6VmzQB+pC5nmwQ@public.gmane.org>
Subject: [PATCH RESEND v7] gpio: Device tree support for LPC32xx
Date: Thu, 26 Apr 2012 21:51:00 +0200 [thread overview]
Message-ID: <1335469860-3337-1-git-send-email-stigge@antcom.de> (raw)
This patch adds device tree support for gpio-lpc32xx.c
Signed-off-by: Roland Stigge <stigge-uj/7R2tJ6VmzQB+pC5nmwQ@public.gmane.org>
---
Applies to v3.4-rc4
Changes since last version:
* Split up lpc32xx_gpio_probe() for readability
Thanks to Jean-Christophe PLAGNIOL-VILLARD for reviewing!
Documentation/devicetree/bindings/gpio/gpio_lpc32xx.txt | 65 ++++++++++++++++
arch/arm/mach-lpc32xx/include/mach/gpio.h | 9 +-
drivers/gpio/gpio-lpc32xx.c | 56 +++++++++++++
3 files changed, 127 insertions(+), 3 deletions(-)
--- /dev/null
+++ linux-2.6/Documentation/devicetree/bindings/gpio/gpio_lpc32xx.txt
@@ -0,0 +1,65 @@
+NXP LPC32xx SoC GPIO controller
+
+Required properties:
+- compatible: must be "nxp,lpc3220-gpio"
+- reg: Physical base address and length of the controller's registers.
+- #address-cells: Always 1, for indexing of the subnodes (GPIO groups of the
+ SoC)
+- #size-cells: Always 0
+
+Required properties of sub-nodes which describe the GPIO groups of LPC32xx:
+- gpio-controller: Marks the device node as a GPIO controller.
+- #gpio-cells: Should be two. The first cell is the pin number and the
+ second cell is used to specify optional parameters:
+ - bit 0 specifies polarity (0 for normal, 1 for inverted)
+- reg: Index of the GPIO group
+
+Optional properties of sub-nodes which describe the GPIO groups of LPC32xx:
+- status: Set to "disabled" if you don't use the respective GPIO group
+ of the LPC32xx SoC
+
+Example:
+
+ gpio: gpio@40028000 {
+ compatible = "nxp,lpc3220-gpio";
+ reg = <0x40028000 0x1000>;
+ /* create a private address space for enumeration */
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ gpio_p0: gpio-bank@0 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0>;
+ };
+
+ gpio_p1: gpio-bank@1 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <1>;
+ };
+
+ gpio_p2: gpio-bank@2 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <2>;
+ };
+
+ gpio_p3: gpio-bank@3 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <3>;
+ };
+
+ gpi_p3: gpio-bank@4 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <4>;
+ };
+
+ gpo_p3: gpio-bank@5 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <5>;
+ };
+ };
--- linux-2.6.orig/arch/arm/mach-lpc32xx/include/mach/gpio.h
+++ linux-2.6/arch/arm/mach-lpc32xx/include/mach/gpio.h
@@ -1 +1,8 @@
-/* empty */
+#ifndef __MACH_GPIO_H
+#define __MACH_GPIO_H
+
+#include "gpio-lpc32xx.h"
+
+#define ARCH_NR_GPIOS (LPC32XX_GPO_P3_GRP + LPC32XX_GPO_P3_MAX)
+
+#endif /* __MACH_GPIO_H */
--- linux-2.6.orig/drivers/gpio/gpio-lpc32xx.c
+++ linux-2.6/drivers/gpio/gpio-lpc32xx.c
@@ -21,6 +21,9 @@
#include <linux/io.h>
#include <linux/errno.h>
#include <linux/gpio.h>
+#include <linux/of_gpio.h>
+#include <linux/platform_device.h>
+#include <linux/module.h>
#include <mach/hardware.h>
#include <mach/platform.h>
@@ -454,10 +457,59 @@ static struct lpc32xx_gpio_chip lpc32xx_
},
};
+/* Empty now, can be removed later when mach-lpc32xx is finally switched over
+ * to DT support
+ */
void __init lpc32xx_gpio_init(void)
{
+}
+
+static void __devinit lpc32xx_gpiochip_add_dt(struct device_node *node)
+{
+ if (of_device_is_available(node)) {
+ u32 index;
+ struct gpio_chip *chip;
+
+ if (of_property_read_u32(node, "reg", &index) < 0)
+ return;
+ if (index >= ARRAY_SIZE(lpc32xx_gpiochip))
+ return;
+ chip = &lpc32xx_gpiochip[index].chip;
+ chip->of_node = of_node_get(node);
+ gpiochip_add(chip);
+ }
+}
+
+static int __devinit lpc32xx_gpio_probe(struct platform_device *pdev)
+{
+ struct device_node *node;
int i;
- for (i = 0; i < ARRAY_SIZE(lpc32xx_gpiochip); i++)
- gpiochip_add(&lpc32xx_gpiochip[i].chip);
+ if (pdev->dev.of_node) {
+ for_each_child_of_node(pdev->dev.of_node, node)
+ lpc32xx_gpiochip_add_dt(node);
+ } else {
+ for (i = 0; i < ARRAY_SIZE(lpc32xx_gpiochip); i++)
+ gpiochip_add(&lpc32xx_gpiochip[i].chip);
+ }
+
+ return 0;
}
+
+#ifdef CONFIG_OF
+static struct of_device_id lpc32xx_gpio_of_match[] __devinitdata = {
+ { .compatible = "nxp,lpc3220-gpio", },
+ { },
+};
+#endif
+
+static struct platform_driver lpc32xx_gpio_driver = {
+ .driver = {
+ .name = "lpc32xx-gpio",
+ .owner = THIS_MODULE,
+ .of_match_table = of_match_ptr(lpc32xx_gpio_of_match),
+ },
+ .probe = lpc32xx_gpio_probe,
+};
+
+module_platform_driver(lpc32xx_gpio_driver);
reply other threads:[~2012-04-26 19:51 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1335469860-3337-1-git-send-email-stigge@antcom.de \
--to=stigge-uj/7r2tj6vmzqb+pc5nmwq@public.gmane.org \
--cc=arm-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org \
--cc=devicetree-discuss-uLR06cmDAlY/bJ5BZ2RsiQ@public.gmane.org \
--cc=grant.likely-s3s/WqlpOiPyB63q8FvJNQ@public.gmane.org \
--cc=kevin.wells-3arQi8VN3Tc@public.gmane.org \
--cc=linus.walleij-0IS4wlFg1OjSUeElwK9/Pw@public.gmane.org \
--cc=linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org \
--cc=linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=rob.herring-bsGFqQB8/DxBDgjK7y7TUQ@public.gmane.org \
--cc=srinivas.bakki-3arQi8VN3Tc@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).