Re: [PATCH v2 3/3] arm64: dts: qcom: sc8280xp: Add soundcard support

[Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>]

On 19/11/2022 17:44, Srinivas Kandagatla wrote:
> Add support for SoundCard on X13s. This patch adds support for Headset
> Playback, record and 2 DMICs on the Panel along with the regulators
> required for powering up the LPASS codecs.
> 
> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
> ---

Thank you for your patch. There is something to discuss/improve.

> +	right_spkr: wsa8830-right@0,2{
> +		compatible = "sdw10217020200";
> +		reg = <0 2>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&spkr_2_sd_n_default>;
> +		powerdown-gpios = <&tlmm 179 GPIO_ACTIVE_LOW>;
> +		#thermal-sensor-cells = <0>;
> +		sound-name-prefix = "SpkrRight";
> +		#sound-dai-cells = <0>;
> +		vdd-supply = <&vreg_s10b>;
> +	};
> +};
> +
> +

Only one blank line.

> +&swr1 {
> +	status = "okay";
> +
> +	wcd_rx: wcd9380-rx@0,4 {
> +		compatible = "sdw20217010d00";
> +		reg = <0 4>;
> +		qcom,rx-port-mapping = <1 2 3 4 5 6>;

No improvements: Still looks too long.

> +

Drop empty line.
> +	};
> +};
> +
> +&swr2 {
> +	status = "okay";
> +
> +	wcd_tx: wcd9380-tx@0,3 {
> +		compatible = "sdw20217010d00";
> +		reg = <0 3>;
> +		qcom,tx-port-mapping = <1 1 2 3>;
> +	};
> +};
> +
> +&vamacro {
> +	pinctrl-0 = <&dmic01_default>, <&dmic02_default>;
> +	pinctrl-names = "default";
> +	vdd-micb-supply = <&vreg_s10b>;
> +	qcom,dmic-sample-rate = <600000>;
> +};
> +
>  &tlmm {
>  	gpio-reserved-ranges = <70 2>, <74 6>, <83 4>, <125 2>, <128 2>, <154 7>;
>  
> @@ -369,6 +558,14 @@ reset {
>  		};
>  	};
>  
> +	wcd_default: wcd-default-state {
> +		reset-pins {
> +			pins = "gpio106";
> +			function = "gpio";
> +			bias-disable;
> +		};
> +	};
> +
>  	qup0_i2c4_default: qup0-i2c4-default-state {
>  		pins = "gpio171", "gpio172";
>  		function = "qup4";
> @@ -383,6 +580,26 @@ qup2_i2c5_default: qup2-i2c5-default-state {
>  		drive-strength = <16>;
>  	};
>  
> +	spkr_1_sd_n_default: spkr-1-sd-n-default-state {
> +		perst-n-pins {
> +			pins = "gpio178";
> +			function = "gpio";
> +			drive-strength = <16>;
> +			bias-disable;
> +			output-high;
> +		};
> +	};
> +
> +	spkr_2_sd_n_default: spkr-2-sd-n-default-state {
> +		perst-n-pins {
> +			pins = "gpio179";
> +			function = "gpio";
> +			drive-strength = <16>;
> +			bias-disable;
> +			output-high;
> +		};
> +	};
> +
>  	tpad_default: tpad-default-state {
>  		int-n {

This won't apply cleanly. You need to base your patches on recent trees.

Best regards,
Krzysztof