[PATCH v4 2/8] input: ti_am335x_tsc: Order of TSC wires, made configurable

["Patil, Rachna" <rachna-l0cyMroinI0@public.gmane.org>]

From: "Patil, Rachna" <rachna-l0cyMroinI0@public.gmane.org>

The current driver expected touchscreen input
wires(XP,XN,YP,YN) to be connected in a particular order.
Making changes to accept this as platform data.

Signed-off-by: Patil, Rachna <rachna-l0cyMroinI0@public.gmane.org>
---
 drivers/input/touchscreen/ti_am335x_tsc.c |  156 ++++++++++++++++++++++++++---
 include/linux/input/ti_am335x_tsc.h       |   12 +++
 include/linux/mfd/ti_am335x_tscadc.h      |   10 +-
 3 files changed, 159 insertions(+), 19 deletions(-)

diff --git a/drivers/input/touchscreen/ti_am335x_tsc.c b/drivers/input/touchscreen/ti_am335x_tsc.c
index da652e0..0c460f9 100644
--- a/drivers/input/touchscreen/ti_am335x_tsc.c
+++ b/drivers/input/touchscreen/ti_am335x_tsc.c
@@ -33,6 +33,17 @@
 #define SEQ_SETTLE		275
 #define MAX_12BIT		((1 << 12) - 1)
 
+/*
+ * Refer to function regbit_map() to
+ * map the values in the matrix.
+ */
+static int config[4][4] = {
+		{1,	0,	1,	0},
+		{2,	3,	2,	3},
+		{4,	5,	4,	5},
+		{0,	6,	0,	6}
+};
+
 struct titsc {
 	struct input_dev	*input;
 	struct ti_tscadc_dev	*mfd_tscadc;
@@ -42,6 +53,9 @@ struct titsc {
 	unsigned int		enable_bits;
 	bool			pen_down;
 	int			steps_to_configure;
+	int			config_inp[20];
+	int			bit_xp, bit_xn, bit_yp, bit_yn;
+	int			inp_xp, inp_xn, inp_yp, inp_yn;
 };
 
 static unsigned int titsc_readl(struct titsc *ts, unsigned int reg)
@@ -55,6 +69,107 @@ static void titsc_writel(struct titsc *tsc, unsigned int reg,
 	writel(val, tsc->mfd_tscadc->tscadc_base + reg);
 }
 
+/*
+ * Each of the analog lines are mapped
+ * with one or two register bits,
+ * which can be either pulled high/low
+ * depending on the value to be read.
+ */
+static int regbit_map(int val)
+{
+	int map_bits = 0;
+
+	switch (val) {
+	case 1:
+		map_bits = XPP;
+		break;
+	case 2:
+		map_bits = XNP;
+		break;
+	case 3:
+		map_bits = XNN;
+		break;
+	case 4:
+		map_bits = YPP;
+		break;
+	case 5:
+		map_bits = YPN;
+		break;
+	case 6:
+		map_bits = YNN;
+		break;
+	}
+
+	return map_bits;
+}
+
+static int titsc_config_wires(struct titsc *ts_dev)
+{
+	int		analog_line[10], wire_order[10];
+	int		i, temp_bits, err;
+
+	for (i = 0; i < 4; i++) {
+		/*
+		 * Get the order in which TSC wires are attached
+		 * w.r.t. each of the analog input lines on the EVM.
+		 */
+		analog_line[i] = ts_dev->config_inp[i] & 0xF0;
+		analog_line[i] = analog_line[i] >> 4;
+
+		wire_order[i] = ts_dev->config_inp[i] & 0x0F;
+	}
+
+	for (i = 0; i < 4; i++) {
+		switch (wire_order[i]) {
+		case 0:
+			temp_bits = config[analog_line[i]][0];
+			if (temp_bits == 0) {
+				err = -EINVAL;
+				goto ret;
+			} else {
+				ts_dev->bit_xp = regbit_map(temp_bits);
+				ts_dev->inp_xp = analog_line[i];
+				break;
+			}
+		case 1:
+			temp_bits = config[analog_line[i]][1];
+			if (temp_bits == 0) {
+				err = -EINVAL;
+				goto ret;
+			} else {
+				ts_dev->bit_xn = regbit_map(temp_bits);
+				ts_dev->inp_xn = analog_line[i];
+				break;
+			}
+		case 2:
+			temp_bits = config[analog_line[i]][2];
+			if (temp_bits == 0) {
+				err = -EINVAL;
+				goto ret;
+			} else {
+				ts_dev->bit_yp = regbit_map(temp_bits);
+				ts_dev->inp_yp = analog_line[i];
+				break;
+			}
+		case 3:
+			temp_bits = config[analog_line[i]][3];
+			if (temp_bits == 0) {
+				err = -EINVAL;
+				goto ret;
+			} else {
+				ts_dev->bit_yn = regbit_map(temp_bits);
+				ts_dev->inp_yn = analog_line[i];
+				break;
+			}
+		}
+	}
+
+	return 0;
+
+ret:
+	return err;
+}
+
 static void titsc_step_config(struct titsc *ts_dev)
 {
 	unsigned int	config;
@@ -65,18 +180,18 @@ static void titsc_step_config(struct titsc *ts_dev)
 	total_steps = 2 * ts_dev->steps_to_configure;
 
 	config = STEPCONFIG_MODE_HWSYNC |
-			STEPCONFIG_AVG_16 | STEPCONFIG_XPP;
+			STEPCONFIG_AVG_16 | ts_dev->bit_xp;
 	switch (ts_dev->wires) {
 	case 4:
-		config |= STEPCONFIG_INP_AN2 | STEPCONFIG_XNN;
+		config |= STEPCONFIG_INP(ts_dev->inp_yp) | ts_dev->bit_xn;
 		break;
 	case 5:
-		config |= STEPCONFIG_YNN |
-				STEPCONFIG_INP_AN4 | STEPCONFIG_XNN |
-				STEPCONFIG_YPP;
+		config |= ts_dev->bit_yn |
+				STEPCONFIG_INP_AN4 | ts_dev->bit_xn |
+				ts_dev->bit_yp;
 		break;
 	case 8:
-		config |= STEPCONFIG_INP_AN2 | STEPCONFIG_XNN;
+		config |= STEPCONFIG_INP(ts_dev->inp_yp) | ts_dev->bit_xn;
 		break;
 	}
 
@@ -87,18 +202,18 @@ static void titsc_step_config(struct titsc *ts_dev)
 
 	config = 0;
 	config = STEPCONFIG_MODE_HWSYNC |
-			STEPCONFIG_AVG_16 | STEPCONFIG_YNN |
+			STEPCONFIG_AVG_16 | ts_dev->bit_yn |
 			STEPCONFIG_INM_ADCREFM | STEPCONFIG_FIFO1;
 	switch (ts_dev->wires) {
 	case 4:
-		config |= STEPCONFIG_YPP;
+		config |= ts_dev->bit_yp | STEPCONFIG_INP(ts_dev->inp_xp);
 		break;
 	case 5:
-		config |= STEPCONFIG_XPP | STEPCONFIG_INP_AN4 |
-				STEPCONFIG_XNP | STEPCONFIG_YPN;
+		config |= ts_dev->bit_xp | STEPCONFIG_INP_AN4 |
+				ts_dev->bit_xn | ts_dev->bit_yp;
 		break;
 	case 8:
-		config |= STEPCONFIG_YPP;
+		config |= ts_dev->bit_yp | STEPCONFIG_INP(ts_dev->inp_xp);
 		break;
 	}
 
@@ -109,9 +224,9 @@ static void titsc_step_config(struct titsc *ts_dev)
 
 	config = 0;
 	/* Charge step configuration */
-	config = STEPCONFIG_XPP | STEPCONFIG_YNN |
+	config = ts_dev->bit_xp | ts_dev->bit_yn |
 			STEPCHARGE_RFP_XPUL | STEPCHARGE_RFM_XNUR |
-			STEPCHARGE_INM_AN1 | STEPCHARGE_INP_AN1;
+			STEPCHARGE_INM_AN1 | STEPCHARGE_INP(ts_dev->inp_yp);
 
 	titsc_writel(ts_dev, REG_CHARGECONFIG, config);
 	titsc_writel(ts_dev, REG_CHARGEDELAY, CHARGEDLY_OPENDLY);
@@ -119,13 +234,14 @@ static void titsc_step_config(struct titsc *ts_dev)
 	config = 0;
 	/* Configure to calculate pressure */
 	config = STEPCONFIG_MODE_HWSYNC |
-			STEPCONFIG_AVG_16 | STEPCONFIG_YPP |
-			STEPCONFIG_XNN | STEPCONFIG_INM_ADCREFM;
+			STEPCONFIG_AVG_16 | ts_dev->bit_yp |
+			ts_dev->bit_xn | STEPCONFIG_INM_ADCREFM |
+			STEPCONFIG_INP(ts_dev->inp_xp);
 	titsc_writel(ts_dev, REG_STEPCONFIG(total_steps + 1), config);
 	titsc_writel(ts_dev, REG_STEPDELAY(total_steps + 1),
 			STEPCONFIG_OPENDLY);
 
-	config |= STEPCONFIG_INP_AN3 | STEPCONFIG_FIFO1;
+	config |= STEPCONFIG_INP(ts_dev->inp_yn) | STEPCONFIG_FIFO1;
 	titsc_writel(ts_dev, REG_STEPCONFIG(total_steps + 2), config);
 	titsc_writel(ts_dev, REG_STEPDELAY(total_steps + 2),
 			STEPCONFIG_OPENDLY);
@@ -295,6 +411,8 @@ static int titsc_probe(struct platform_device *pdev)
 	ts_dev->wires = pdata->tsc_init->wires;
 	ts_dev->x_plate_resistance = pdata->tsc_init->x_plate_resistance;
 	ts_dev->steps_to_configure = pdata->tsc_init->steps_to_configure;
+	memcpy(ts_dev->config_inp, pdata->tsc_init->wire_config,
+			sizeof(pdata->tsc_init->wire_config));
 
 	err = request_irq(ts_dev->irq, titsc_irq,
 			  0, pdev->dev.driver->name, ts_dev);
@@ -304,6 +422,11 @@ static int titsc_probe(struct platform_device *pdev)
 	}
 
 	titsc_writel(ts_dev, REG_IRQENABLE, IRQENB_FIFO0THRES);
+	err = titsc_config_wires(ts_dev);
+	if (err) {
+		dev_err(&pdev->dev, "wrong i/p wire configuration\n");
+		goto err_free_irq;
+	}
 	titsc_step_config(ts_dev);
 	titsc_writel(ts_dev, REG_FIFO0THR, ts_dev->steps_to_configure);
 
@@ -373,6 +496,7 @@ static int titsc_resume(struct device *dev)
 				0x00);
 		titsc_writel(ts_dev, REG_IRQCLR, IRQENB_HW_PEN);
 	}
+	titsc_config_wires(ts_dev);
 	titsc_step_config(ts_dev);
 	titsc_writel(ts_dev, REG_FIFO0THR,
 			ts_dev->steps_to_configure);
diff --git a/include/linux/input/ti_am335x_tsc.h b/include/linux/input/ti_am335x_tsc.h
index 49269a2..6a66b4d 100644
--- a/include/linux/input/ti_am335x_tsc.h
+++ b/include/linux/input/ti_am335x_tsc.h
@@ -12,12 +12,24 @@
  *			A step configured to read a single
  *			co-ordinate value, can be applied
  *			more number of times for better results.
+ * @wire_config:	Different EVM's could have a different order
+ *			for connecting wires on touchscreen.
+ *			We need to provide an 8 bit number where in
+ *			the 1st four bits represent the analog lines
+ *			and the next 4 bits represent positive/
+ *			negative terminal on that input line.
+ *			Notations to represent the input lines and
+ *			terminals resoectively is as follows:
+ *			AIN0 = 0, AIN1 = 1 and so on till AIN7 = 7.
+ *			XP  = 0, XN = 1, YP = 2, YN = 3.
+ *
  */
 
 struct tsc_data {
 	int wires;
 	int x_plate_resistance;
 	int steps_to_configure;
+	int wire_config[10];
 };
 
 #endif
diff --git a/include/linux/mfd/ti_am335x_tscadc.h b/include/linux/mfd/ti_am335x_tscadc.h
index 23e4f33..9624fea 100644
--- a/include/linux/mfd/ti_am335x_tscadc.h
+++ b/include/linux/mfd/ti_am335x_tscadc.h
@@ -72,8 +72,6 @@
 #define STEPCONFIG_INM_ADCREFM	STEPCONFIG_INM(8)
 #define STEPCONFIG_INP_MASK	(0xF << 19)
 #define STEPCONFIG_INP(val)	((val) << 19)
-#define STEPCONFIG_INP_AN2	STEPCONFIG_INP(2)
-#define STEPCONFIG_INP_AN3	STEPCONFIG_INP(3)
 #define STEPCONFIG_INP_AN4	STEPCONFIG_INP(4)
 #define STEPCONFIG_INP_ADCREFM	STEPCONFIG_INP(8)
 #define STEPCONFIG_FIFO1	BIT(26)
@@ -95,7 +93,6 @@
 #define STEPCHARGE_INM_AN1	STEPCHARGE_INM(1)
 #define STEPCHARGE_INP_MASK	(0xF << 19)
 #define STEPCHARGE_INP(val)	((val) << 19)
-#define STEPCHARGE_INP_AN1	STEPCHARGE_INP(1)
 #define STEPCHARGE_RFM_MASK	(3 << 23)
 #define STEPCHARGE_RFM(val)	((val) << 23)
 #define STEPCHARGE_RFM_XNUR	STEPCHARGE_RFM(1)
@@ -117,6 +114,13 @@
 #define CNTRLREG_8WIRE		CNTRLREG_AFE_CTRL(3)
 #define CNTRLREG_TSCENB		BIT(7)
 
+#define XPP			STEPCONFIG_XPP
+#define XNP			STEPCONFIG_XNP
+#define XNN			STEPCONFIG_XNN
+#define YPP			STEPCONFIG_YPP
+#define YPN			STEPCONFIG_YPN
+#define YNN			STEPCONFIG_YNN
+
 #define ADC_CLK			3000000
 #define	MAX_CLK_DIV		7
 #define TOTAL_STEPS		16
-- 
1.7.9.5