[PATCH v5 0/7] ARM: Exynos: Enable device tree support for MCT controller

[PATCH v5 0/7] ARM: Exynos: Enable device tree support for MCT controller

[Thomas Abraham]

Changes since v4:
- Rebased to 3.8-rc7
- Updated the MCT controller device nodes to list all the four global timer
  interrupts generated by the MCT controller.

Changes since v3:
- Based on Stephen Warren's CONFIG_CLKSRC_OF patches (merged from arm-soc
  'timer/cleanup' branch).
- Moved the mct driver from mach-exynos to drivers/clocksource as suggested
  by Olof.

Changes since v2:
- Rebased to linux 3.8-rc1

Changes since v1:
- Includes changes suggested by Sylwester Nawrocki <sylvester.nawrocki@gmail.com>

This patch series adds device tree support for Exynos4/5 MCT controller and
moves the MCT driver from mach-exynos to drivers/clocksource. This has been
tested on Exynos4210 based Origen board, Exynos4412 based Origen board and
Exynos5250 based SMDK board.

[PATCH 1/7] ARM: Exynos: add a register base address variable in mct controller driver

[Thomas Abraham]

All the MCT register read/writes use a fixed remapped address S5P_VA_SYSTIMER.
With device tree support for MCT controller, it is possible to remove the
static remap of the MCT controller address space and do the remap during the
initialization of the MCT controller with the physical address obtained from
the device tree.

So in preparation of adding device tree support for MCT controller, add a new
register base address variable that will hold the remapped MCT controller base
address and convert all MCT register read/writes to use this new variable as
the base address instead of the fixed S5P_VA_SYSTIMER.

While at it, the MCT register offset and bit mask definitions are moved into
the MCT controller driver file since there are no other consumers of these
definitions.

Cc: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
---
 arch/arm/mach-exynos/include/mach/regs-mct.h |   53 --------------
 arch/arm/mach-exynos/mct.c                   |   97 ++++++++++++++++---------
 2 files changed, 62 insertions(+), 88 deletions(-)
 delete mode 100644 arch/arm/mach-exynos/include/mach/regs-mct.h

diff --git a/arch/arm/mach-exynos/include/mach/regs-mct.h b/arch/arm/mach-exynos/include/mach/regs-mct.h
deleted file mode 100644
index 80dd02a..0000000
--- a/arch/arm/mach-exynos/include/mach/regs-mct.h
+++ /dev/null
@@ -1,53 +0,0 @@
-/* arch/arm/mach-exynos4/include/mach/regs-mct.h
- *
- * Copyright (c) 2011 Samsung Electronics Co., Ltd.
- *		http://www.samsung.com
- *
- * EXYNOS4 MCT configutation
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#ifndef __ASM_ARCH_REGS_MCT_H
-#define __ASM_ARCH_REGS_MCT_H __FILE__
-
-#include <mach/map.h>
-
-#define EXYNOS4_MCTREG(x)		(S5P_VA_SYSTIMER + (x))
-
-#define EXYNOS4_MCT_G_CNT_L		EXYNOS4_MCTREG(0x100)
-#define EXYNOS4_MCT_G_CNT_U		EXYNOS4_MCTREG(0x104)
-#define EXYNOS4_MCT_G_CNT_WSTAT		EXYNOS4_MCTREG(0x110)
-
-#define EXYNOS4_MCT_G_COMP0_L		EXYNOS4_MCTREG(0x200)
-#define EXYNOS4_MCT_G_COMP0_U		EXYNOS4_MCTREG(0x204)
-#define EXYNOS4_MCT_G_COMP0_ADD_INCR	EXYNOS4_MCTREG(0x208)
-
-#define EXYNOS4_MCT_G_TCON		EXYNOS4_MCTREG(0x240)
-
-#define EXYNOS4_MCT_G_INT_CSTAT		EXYNOS4_MCTREG(0x244)
-#define EXYNOS4_MCT_G_INT_ENB		EXYNOS4_MCTREG(0x248)
-#define EXYNOS4_MCT_G_WSTAT		EXYNOS4_MCTREG(0x24C)
-
-#define _EXYNOS4_MCT_L_BASE		EXYNOS4_MCTREG(0x300)
-#define EXYNOS4_MCT_L_BASE(x)		(_EXYNOS4_MCT_L_BASE + (0x100 * x))
-#define EXYNOS4_MCT_L_MASK		(0xffffff00)
-
-#define MCT_L_TCNTB_OFFSET		(0x00)
-#define MCT_L_ICNTB_OFFSET		(0x08)
-#define MCT_L_TCON_OFFSET		(0x20)
-#define MCT_L_INT_CSTAT_OFFSET		(0x30)
-#define MCT_L_INT_ENB_OFFSET		(0x34)
-#define MCT_L_WSTAT_OFFSET		(0x40)
-
-#define MCT_G_TCON_START		(1 << 8)
-#define MCT_G_TCON_COMP0_AUTO_INC	(1 << 1)
-#define MCT_G_TCON_COMP0_ENABLE		(1 << 0)
-
-#define MCT_L_TCON_INTERVAL_MODE	(1 << 2)
-#define MCT_L_TCON_INT_START		(1 << 1)
-#define MCT_L_TCON_TIMER_START		(1 << 0)
-
-#endif /* __ASM_ARCH_REGS_MCT_H */
diff --git a/arch/arm/mach-exynos/mct.c b/arch/arm/mach-exynos/mct.c
index 577ee1b..e3d67ec 100644
--- a/arch/arm/mach-exynos/mct.c
+++ b/arch/arm/mach-exynos/mct.c
@@ -29,9 +29,36 @@
 
 #include <mach/map.h>
 #include <mach/irqs.h>
-#include <mach/regs-mct.h>
 #include <asm/mach/time.h>
 
+#define EXYNOS4_MCTREG(x)		(x)
+#define EXYNOS4_MCT_G_CNT_L		EXYNOS4_MCTREG(0x100)
+#define EXYNOS4_MCT_G_CNT_U		EXYNOS4_MCTREG(0x104)
+#define EXYNOS4_MCT_G_CNT_WSTAT		EXYNOS4_MCTREG(0x110)
+#define EXYNOS4_MCT_G_COMP0_L		EXYNOS4_MCTREG(0x200)
+#define EXYNOS4_MCT_G_COMP0_U		EXYNOS4_MCTREG(0x204)
+#define EXYNOS4_MCT_G_COMP0_ADD_INCR	EXYNOS4_MCTREG(0x208)
+#define EXYNOS4_MCT_G_TCON		EXYNOS4_MCTREG(0x240)
+#define EXYNOS4_MCT_G_INT_CSTAT		EXYNOS4_MCTREG(0x244)
+#define EXYNOS4_MCT_G_INT_ENB		EXYNOS4_MCTREG(0x248)
+#define EXYNOS4_MCT_G_WSTAT		EXYNOS4_MCTREG(0x24C)
+#define _EXYNOS4_MCT_L_BASE		EXYNOS4_MCTREG(0x300)
+#define EXYNOS4_MCT_L_BASE(x)		(_EXYNOS4_MCT_L_BASE + (0x100 * x))
+#define EXYNOS4_MCT_L_MASK		(0xffffff00)
+
+#define MCT_L_TCNTB_OFFSET		(0x00)
+#define MCT_L_ICNTB_OFFSET		(0x08)
+#define MCT_L_TCON_OFFSET		(0x20)
+#define MCT_L_INT_CSTAT_OFFSET		(0x30)
+#define MCT_L_INT_ENB_OFFSET		(0x34)
+#define MCT_L_WSTAT_OFFSET		(0x40)
+#define MCT_G_TCON_START		(1 << 8)
+#define MCT_G_TCON_COMP0_AUTO_INC	(1 << 1)
+#define MCT_G_TCON_COMP0_ENABLE		(1 << 0)
+#define MCT_L_TCON_INTERVAL_MODE	(1 << 2)
+#define MCT_L_TCON_INT_START		(1 << 1)
+#define MCT_L_TCON_TIMER_START		(1 << 0)
+
 #define TICK_BASE_CNT	1
 
 enum {
@@ -39,64 +66,62 @@ enum {
 	MCT_INT_PPI
 };
 
+static void __iomem *reg_base;
 static unsigned long clk_rate;
 static unsigned int mct_int_type;
 
 struct mct_clock_event_device {
 	struct clock_event_device *evt;
-	void __iomem *base;
+	unsigned long base;
 	char name[10];
 };
 
-static void exynos4_mct_write(unsigned int value, void *addr)
+static void exynos4_mct_write(unsigned int value, unsigned long offset)
 {
-	void __iomem *stat_addr;
+	unsigned long stat_addr;
 	u32 mask;
 	u32 i;
 
-	__raw_writel(value, addr);
+	__raw_writel(value, reg_base + offset);
 
-	if (likely(addr >= EXYNOS4_MCT_L_BASE(0))) {
-		u32 base = (u32) addr & EXYNOS4_MCT_L_MASK;
-		switch ((u32) addr & ~EXYNOS4_MCT_L_MASK) {
-		case (u32) MCT_L_TCON_OFFSET:
-			stat_addr = (void __iomem *) base + MCT_L_WSTAT_OFFSET;
+	if (likely(offset >= EXYNOS4_MCT_L_BASE(0))) {
+		stat_addr = (offset & ~EXYNOS4_MCT_L_MASK) + MCT_L_WSTAT_OFFSET;
+		switch (offset & EXYNOS4_MCT_L_MASK) {
+		case MCT_L_TCON_OFFSET:
 			mask = 1 << 3;		/* L_TCON write status */
 			break;
-		case (u32) MCT_L_ICNTB_OFFSET:
-			stat_addr = (void __iomem *) base + MCT_L_WSTAT_OFFSET;
+		case MCT_L_ICNTB_OFFSET:
 			mask = 1 << 1;		/* L_ICNTB write status */
 			break;
-		case (u32) MCT_L_TCNTB_OFFSET:
-			stat_addr = (void __iomem *) base + MCT_L_WSTAT_OFFSET;
+		case MCT_L_TCNTB_OFFSET:
 			mask = 1 << 0;		/* L_TCNTB write status */
 			break;
 		default:
 			return;
 		}
 	} else {
-		switch ((u32) addr) {
-		case (u32) EXYNOS4_MCT_G_TCON:
+		switch (offset) {
+		case EXYNOS4_MCT_G_TCON:
 			stat_addr = EXYNOS4_MCT_G_WSTAT;
 			mask = 1 << 16;		/* G_TCON write status */
 			break;
-		case (u32) EXYNOS4_MCT_G_COMP0_L:
+		case EXYNOS4_MCT_G_COMP0_L:
 			stat_addr = EXYNOS4_MCT_G_WSTAT;
 			mask = 1 << 0;		/* G_COMP0_L write status */
 			break;
-		case (u32) EXYNOS4_MCT_G_COMP0_U:
+		case EXYNOS4_MCT_G_COMP0_U:
 			stat_addr = EXYNOS4_MCT_G_WSTAT;
 			mask = 1 << 1;		/* G_COMP0_U write status */
 			break;
-		case (u32) EXYNOS4_MCT_G_COMP0_ADD_INCR:
+		case EXYNOS4_MCT_G_COMP0_ADD_INCR:
 			stat_addr = EXYNOS4_MCT_G_WSTAT;
 			mask = 1 << 2;		/* G_COMP0_ADD_INCR w status */
 			break;
-		case (u32) EXYNOS4_MCT_G_CNT_L:
+		case EXYNOS4_MCT_G_CNT_L:
 			stat_addr = EXYNOS4_MCT_G_CNT_WSTAT;
 			mask = 1 << 0;		/* G_CNT_L write status */
 			break;
-		case (u32) EXYNOS4_MCT_G_CNT_U:
+		case EXYNOS4_MCT_G_CNT_U:
 			stat_addr = EXYNOS4_MCT_G_CNT_WSTAT;
 			mask = 1 << 1;		/* G_CNT_U write status */
 			break;
@@ -107,12 +132,12 @@ static void exynos4_mct_write(unsigned int value, void *addr)
 
 	/* Wait maximum 1 ms until written values are applied */
 	for (i = 0; i < loops_per_jiffy / 1000 * HZ; i++)
-		if (__raw_readl(stat_addr) & mask) {
-			__raw_writel(mask, stat_addr);
+		if (__raw_readl(reg_base + stat_addr) & mask) {
+			__raw_writel(mask, reg_base + stat_addr);
 			return;
 		}
 
-	panic("MCT hangs after writing %d (addr:0x%08x)\n", value, (u32)addr);
+	panic("MCT hangs after writing %d (offset:0x%lx)\n", value, offset);
 }
 
 /* Clocksource handling */
@@ -123,7 +148,7 @@ static void exynos4_mct_frc_start(u32 hi, u32 lo)
 	exynos4_mct_write(lo, EXYNOS4_MCT_G_CNT_L);
 	exynos4_mct_write(hi, EXYNOS4_MCT_G_CNT_U);
 
-	reg = __raw_readl(EXYNOS4_MCT_G_TCON);
+	reg = __raw_readl(reg_base + EXYNOS4_MCT_G_TCON);
 	reg |= MCT_G_TCON_START;
 	exynos4_mct_write(reg, EXYNOS4_MCT_G_TCON);
 }
@@ -131,12 +156,12 @@ static void exynos4_mct_frc_start(u32 hi, u32 lo)
 static cycle_t exynos4_frc_read(struct clocksource *cs)
 {
 	unsigned int lo, hi;
-	u32 hi2 = __raw_readl(EXYNOS4_MCT_G_CNT_U);
+	u32 hi2 = __raw_readl(reg_base + EXYNOS4_MCT_G_CNT_U);
 
 	do {
 		hi = hi2;
-		lo = __raw_readl(EXYNOS4_MCT_G_CNT_L);
-		hi2 = __raw_readl(EXYNOS4_MCT_G_CNT_U);
+		lo = __raw_readl(reg_base + EXYNOS4_MCT_G_CNT_L);
+		hi2 = __raw_readl(reg_base + EXYNOS4_MCT_G_CNT_U);
 	} while (hi != hi2);
 
 	return ((cycle_t)hi << 32) | lo;
@@ -168,7 +193,7 @@ static void exynos4_mct_comp0_stop(void)
 {
 	unsigned int tcon;
 
-	tcon = __raw_readl(EXYNOS4_MCT_G_TCON);
+	tcon = __raw_readl(reg_base + EXYNOS4_MCT_G_TCON);
 	tcon &= ~(MCT_G_TCON_COMP0_ENABLE | MCT_G_TCON_COMP0_AUTO_INC);
 
 	exynos4_mct_write(tcon, EXYNOS4_MCT_G_TCON);
@@ -181,7 +206,7 @@ static void exynos4_mct_comp0_start(enum clock_event_mode mode,
 	unsigned int tcon;
 	cycle_t comp_cycle;
 
-	tcon = __raw_readl(EXYNOS4_MCT_G_TCON);
+	tcon = __raw_readl(reg_base + EXYNOS4_MCT_G_TCON);
 
 	if (mode == CLOCK_EVT_MODE_PERIODIC) {
 		tcon |= MCT_G_TCON_COMP0_AUTO_INC;
@@ -274,12 +299,12 @@ static void exynos4_mct_tick_stop(struct mct_clock_event_device *mevt)
 {
 	unsigned long tmp;
 	unsigned long mask = MCT_L_TCON_INT_START | MCT_L_TCON_TIMER_START;
-	void __iomem *addr = mevt->base + MCT_L_TCON_OFFSET;
+	unsigned long offset = mevt->base + MCT_L_TCON_OFFSET;
 
-	tmp = __raw_readl(addr);
+	tmp = __raw_readl(reg_base + offset);
 	if (tmp & mask) {
 		tmp &= ~mask;
-		exynos4_mct_write(tmp, addr);
+		exynos4_mct_write(tmp, offset);
 	}
 }
 
@@ -298,7 +323,7 @@ static void exynos4_mct_tick_start(unsigned long cycles,
 	/* enable MCT tick interrupt */
 	exynos4_mct_write(0x1, mevt->base + MCT_L_INT_ENB_OFFSET);
 
-	tmp = __raw_readl(mevt->base + MCT_L_TCON_OFFSET);
+	tmp = __raw_readl(reg_base + mevt->base + MCT_L_TCON_OFFSET);
 	tmp |= MCT_L_TCON_INT_START | MCT_L_TCON_TIMER_START |
 	       MCT_L_TCON_INTERVAL_MODE;
 	exynos4_mct_write(tmp, mevt->base + MCT_L_TCON_OFFSET);
@@ -350,7 +375,7 @@ static int exynos4_mct_tick_clear(struct mct_clock_event_device *mevt)
 		exynos4_mct_tick_stop(mevt);
 
 	/* Clear the MCT tick interrupt */
-	if (__raw_readl(mevt->base + MCT_L_INT_CSTAT_OFFSET) & 1) {
+	if (__raw_readl(reg_base + mevt->base + MCT_L_INT_CSTAT_OFFSET) & 1) {
 		exynos4_mct_write(0x1, mevt->base + MCT_L_INT_CSTAT_OFFSET);
 		return 1;
 	} else {
@@ -453,6 +478,8 @@ static void __init exynos4_timer_resources(void)
 
 	clk_rate = clk_get_rate(mct_clk);
 
+	reg_base = S5P_VA_SYSTIMER;
+
 #ifdef CONFIG_LOCAL_TIMERS
 	if (mct_int_type == MCT_INT_PPI) {
 		int err;
-- 
1.7.5.4

[PATCH 2/7] ARM: Exynos: prepare an array of MCT interrupt numbers and use it

[Thomas Abraham]

Instead of using soc_is_xxx macro at more than one place in the MCT
controller driver to decide the MCT interrpt number to be setup, populate
a table of known MCT global and local timer interrupts and use the values
in table to setup the MCT interrupts.

This also helps in adding device tree support for MCT controller driver by
allowing the driver to retrieve interrupt numbers from device tree and
populating them into this table, thereby supporting both legacy and dt
functionality to co-exist.

Cc: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
---
 arch/arm/mach-exynos/mct.c |   57 +++++++++++++++++++++++++++----------------
 1 files changed, 36 insertions(+), 21 deletions(-)

diff --git a/arch/arm/mach-exynos/mct.c b/arch/arm/mach-exynos/mct.c
index e3d67ec..aa0ae65 100644
--- a/arch/arm/mach-exynos/mct.c
+++ b/arch/arm/mach-exynos/mct.c
@@ -66,9 +66,22 @@ enum {
 	MCT_INT_PPI
 };
 
+enum {
+	MCT_G0_IRQ,
+	MCT_G1_IRQ,
+	MCT_G2_IRQ,
+	MCT_G3_IRQ,
+	MCT_L0_IRQ,
+	MCT_L1_IRQ,
+	MCT_L2_IRQ,
+	MCT_L3_IRQ,
+	MCT_NR_IRQS,
+};
+
 static void __iomem *reg_base;
 static unsigned long clk_rate;
 static unsigned int mct_int_type;
+static int mct_irqs[MCT_NR_IRQS];
 
 struct mct_clock_event_device {
 	struct clock_event_device *evt;
@@ -283,11 +296,7 @@ static void exynos4_clockevent_init(void)
 	mct_comp_device.cpumask = cpumask_of(0);
 	clockevents_config_and_register(&mct_comp_device, clk_rate,
 					0xf, 0xffffffff);
-
-	if (soc_is_exynos5250())
-		setup_irq(EXYNOS5_IRQ_MCT_G0, &mct_comp_event_irq);
-	else
-		setup_irq(EXYNOS4_IRQ_MCT_G0, &mct_comp_event_irq);
+	setup_irq(mct_irqs[MCT_G0_IRQ], &mct_comp_event_irq);
 }
 
 #ifdef CONFIG_LOCAL_TIMERS
@@ -411,7 +420,6 @@ static int __cpuinit exynos4_local_timer_setup(struct clock_event_device *evt)
 {
 	struct mct_clock_event_device *mevt;
 	unsigned int cpu = smp_processor_id();
-	int mct_lx_irq;
 
 	mevt = this_cpu_ptr(&percpu_mct_tick);
 	mevt->evt = evt;
@@ -432,21 +440,17 @@ static int __cpuinit exynos4_local_timer_setup(struct clock_event_device *evt)
 
 	if (mct_int_type == MCT_INT_SPI) {
 		if (cpu == 0) {
-			mct_lx_irq = soc_is_exynos4210() ? EXYNOS4_IRQ_MCT_L0 :
-						EXYNOS5_IRQ_MCT_L0;
 			mct_tick0_event_irq.dev_id = mevt;
-			evt->irq = mct_lx_irq;
-			setup_irq(mct_lx_irq, &mct_tick0_event_irq);
+			evt->irq = mct_irqs[MCT_L0_IRQ];
+			setup_irq(evt->irq, &mct_tick0_event_irq);
 		} else {
-			mct_lx_irq = soc_is_exynos4210() ? EXYNOS4_IRQ_MCT_L1 :
-						EXYNOS5_IRQ_MCT_L1;
 			mct_tick1_event_irq.dev_id = mevt;
-			evt->irq = mct_lx_irq;
-			setup_irq(mct_lx_irq, &mct_tick1_event_irq);
-			irq_set_affinity(mct_lx_irq, cpumask_of(1));
+			evt->irq = mct_irqs[MCT_L1_IRQ];
+			setup_irq(evt->irq, &mct_tick1_event_irq);
+			irq_set_affinity(evt->irq, cpumask_of(1));
 		}
 	} else {
-		enable_percpu_irq(EXYNOS_IRQ_MCT_LOCALTIMER, 0);
+		enable_percpu_irq(mct_irqs[MCT_L0_IRQ], 0);
 	}
 
 	return 0;
@@ -462,7 +466,7 @@ static void exynos4_local_timer_stop(struct clock_event_device *evt)
 		else
 			remove_irq(evt->irq, &mct_tick1_event_irq);
 	else
-		disable_percpu_irq(EXYNOS_IRQ_MCT_LOCALTIMER);
+		disable_percpu_irq(mct_irqs[MCT_L0_IRQ]);
 }
 
 static struct local_timer_ops exynos4_mct_tick_ops __cpuinitdata = {
@@ -484,11 +488,11 @@ static void __init exynos4_timer_resources(void)
 	if (mct_int_type == MCT_INT_PPI) {
 		int err;
 
-		err = request_percpu_irq(EXYNOS_IRQ_MCT_LOCALTIMER,
+		err = request_percpu_irq(mct_irqs[MCT_L0_IRQ],
 					 exynos4_mct_tick_isr, "MCT",
 					 &percpu_mct_tick);
 		WARN(err, "MCT: can't request IRQ %d (%d)\n",
-		     EXYNOS_IRQ_MCT_LOCALTIMER, err);
+		     mct_irqs[MCT_L0_IRQ], err);
 	}
 
 	local_timer_register(&exynos4_mct_tick_ops);
@@ -502,10 +506,21 @@ void __init exynos4_timer_init(void)
 		return;
 	}
 
-	if ((soc_is_exynos4210()) || (soc_is_exynos5250()))
+	if (soc_is_exynos4210()) {
+		mct_irqs[MCT_G0_IRQ] = EXYNOS4_IRQ_MCT_G0;
+		mct_irqs[MCT_L0_IRQ] = EXYNOS4_IRQ_MCT_L0;
+		mct_irqs[MCT_L1_IRQ] = EXYNOS4_IRQ_MCT_L1;
 		mct_int_type = MCT_INT_SPI;
-	else
+	} else if (soc_is_exynos5250()) {
+		mct_irqs[MCT_G0_IRQ] = EXYNOS5_IRQ_MCT_G0;
+		mct_irqs[MCT_L0_IRQ] = EXYNOS5_IRQ_MCT_L0;
+		mct_irqs[MCT_L1_IRQ] = EXYNOS5_IRQ_MCT_L1;
+		mct_int_type = MCT_INT_SPI;
+	} else {
+		mct_irqs[MCT_G0_IRQ] = EXYNOS4_IRQ_MCT_G0;
+		mct_irqs[MCT_L0_IRQ] = EXYNOS_IRQ_MCT_LOCALTIMER;
 		mct_int_type = MCT_INT_PPI;
+	}
 
 	exynos4_timer_resources();
 	exynos4_clocksource_init();
-- 
1.7.5.4

[PATCH 3/7] ARM: Exynos: add device tree support for MCT controller driver

[Thomas Abraham]

Allow the MCT controller base address and interrupts to be obtained from
device tree and remove unused static definitions of these. The non-dt support
for Exynos5250 is removed but retained for Exynos4210 based platforms.

Cc: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
---
 .../bindings/timer/samsung,exynos4210-mct.txt      |   68 ++++++++++++++++++++
 arch/arm/mach-exynos/include/mach/irqs.h           |    6 --
 arch/arm/mach-exynos/mct.c                         |   49 +++++++++++----
 3 files changed, 105 insertions(+), 18 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/timer/samsung,exynos4210-mct.txt

diff --git a/Documentation/devicetree/bindings/timer/samsung,exynos4210-mct.txt b/Documentation/devicetree/bindings/timer/samsung,exynos4210-mct.txt
new file mode 100644
index 0000000..cb47bfb
--- /dev/null
+++ b/Documentation/devicetree/bindings/timer/samsung,exynos4210-mct.txt
@@ -0,0 +1,68 @@
+Samsung's Multi Core Timer (MCT)
+
+The Samsung's Multi Core Timer (MCT) module includes two main blocks, the
+global timer and CPU local timers. The global timer is a 64-bit free running
+up-counter and can generate 4 interrupts when the counter reaches one of the
+four preset counter values. The CPU local timers are 32-bit free running
+down-counters and generate an interrupt when the counter expires. There is
+one CPU local timer instantiated in MCT for every CPU in the system.
+
+Required properties:
+
+- compatible: should be "samsung,exynos4210-mct".
+  (a) "samsung,exynos4210-mct", for mct compatible with Exynos4210 mct.
+  (b) "samsung,exynos4412-mct", for mct compatible with Exynos4412 mct.
+
+- reg: base address of the mct controller and length of the address space
+  it occupies.
+
+- interrupts: the list of interrupts generated by the controller. The following
+  should be the order of the interrupts specified. The local timer interrupts
+  should be specified after the four global timer interrupts have been
+  specified.
+
+	0: Global Timer Interrupt 0
+	1: Global Timer Interrupt 1
+	2: Global Timer Interrupt 2
+	3: Global Timer Interrupt 3
+	4: Local Timer Interrupt 0
+	5: Local Timer Interrupt 1
+	6: ..
+	7: ..
+	i: Local Timer Interrupt n
+
+Example 1: In this example, the system uses only the first global timer
+	   interrupt generated by MCT and the remaining three global timer
+	   interrupts are unused. Two local timer interrupts have been
+	   specified.
+
+	mct@10050000 {
+		compatible = "samsung,exynos4210-mct";
+		reg = <0x10050000 0x800>;
+		interrupts = <0 57 0>, <0 0 0>, <0 0 0>, <0 0 0>,
+			     <0 42 0>, <0 48 0>;
+	};
+
+Example 2: In this example, the MCT global and local timer interrupts are
+	   connected to two seperate interrupt controllers. Hence, an
+	   interrupt-map is created to map the interrupts to the respective
+	   interrupt controllers.
+
+	mct@101C0000 {
+		compatible = "samsung,exynos4210-mct";
+		reg = <0x101C0000 0x800>;
+		interrupt-controller;
+		#interrups-cells = <2>;
+		interrupt-parent = <&mct_map>;
+		interrupts = <0 0>, <1 0>, <2 0>, <3 0>,
+			     <4 0>, <5 0>;
+
+		mct_map: mct-map {
+			#interrupt-cells = <2>;
+			#address-cells = <0>;
+			#size-cells = <0>;
+			interrupt-map = <0x0 0 &combiner 23 3>,
+					<0x4 0 &gic 0 120 0>,
+					<0x5 0 &gic 0 121 0>;
+		};
+	};
diff --git a/arch/arm/mach-exynos/include/mach/irqs.h b/arch/arm/mach-exynos/include/mach/irqs.h
index 6794292..35fe6d5 100644
--- a/arch/arm/mach-exynos/include/mach/irqs.h
+++ b/arch/arm/mach-exynos/include/mach/irqs.h
@@ -30,8 +30,6 @@
 
 /* For EXYNOS4 and EXYNOS5 */
 
-#define EXYNOS_IRQ_MCT_LOCALTIMER	IRQ_PPI(12)
-
 #define EXYNOS_IRQ_EINT16_31		IRQ_SPI(32)
 
 /* For EXYNOS4 SoCs */
@@ -330,8 +328,6 @@
 #define EXYNOS5_IRQ_CEC			IRQ_SPI(114)
 #define EXYNOS5_IRQ_SATA		IRQ_SPI(115)
 
-#define EXYNOS5_IRQ_MCT_L0		IRQ_SPI(120)
-#define EXYNOS5_IRQ_MCT_L1		IRQ_SPI(121)
 #define EXYNOS5_IRQ_MMC44		IRQ_SPI(123)
 #define EXYNOS5_IRQ_MDMA1		IRQ_SPI(124)
 #define EXYNOS5_IRQ_FIMC_LITE0		IRQ_SPI(125)
@@ -426,8 +422,6 @@
 #define EXYNOS5_IRQ_PMU_CPU1		COMBINER_IRQ(22, 4)
 
 #define EXYNOS5_IRQ_EINT0		COMBINER_IRQ(23, 0)
-#define EXYNOS5_IRQ_MCT_G0		COMBINER_IRQ(23, 3)
-#define EXYNOS5_IRQ_MCT_G1		COMBINER_IRQ(23, 4)
 
 #define EXYNOS5_IRQ_EINT1		COMBINER_IRQ(24, 0)
 #define EXYNOS5_IRQ_SYSMMU_LITE1_0	COMBINER_IRQ(24, 1)
diff --git a/arch/arm/mach-exynos/mct.c b/arch/arm/mach-exynos/mct.c
index aa0ae65..524a859 100644
--- a/arch/arm/mach-exynos/mct.c
+++ b/arch/arm/mach-exynos/mct.c
@@ -20,6 +20,8 @@
 #include <linux/delay.h>
 #include <linux/percpu.h>
 #include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/of_address.h>
 
 #include <asm/arch_timer.h>
 #include <asm/hardware/gic.h>
@@ -475,14 +477,16 @@ static struct local_timer_ops exynos4_mct_tick_ops __cpuinitdata = {
 };
 #endif /* CONFIG_LOCAL_TIMERS */
 
-static void __init exynos4_timer_resources(void)
+static void __init exynos4_timer_resources(struct device_node *np)
 {
 	struct clk *mct_clk;
 	mct_clk = clk_get(NULL, "xtal");
 
 	clk_rate = clk_get_rate(mct_clk);
 
-	reg_base = S5P_VA_SYSTIMER;
+	reg_base = np ? of_iomap(np, 0) : S5P_VA_SYSTIMER;
+	if (!reg_base)
+		panic("%s: unable to ioremap mct address space\n", __func__);
 
 #ifdef CONFIG_LOCAL_TIMERS
 	if (mct_int_type == MCT_INT_PPI) {
@@ -499,30 +503,51 @@ static void __init exynos4_timer_resources(void)
 #endif /* CONFIG_LOCAL_TIMERS */
 }
 
+static const struct of_device_id exynos_mct_ids[] = {
+	{ .compatible = "samsung,exynos4210-mct", .data = (void *)MCT_INT_SPI },
+	{ .compatible = "samsung,exynos4412-mct", .data = (void *)MCT_INT_PPI },
+};
+
 void __init exynos4_timer_init(void)
 {
+	struct device_node *np = NULL;
+	const struct of_device_id *match;
+	u32 nr_irqs, i;
+
 	if (soc_is_exynos5440()) {
 		arch_timer_of_register();
 		return;
 	}
 
-	if (soc_is_exynos4210()) {
+#ifdef CONFIG_OF
+	np = of_find_matching_node_and_match(NULL, exynos_mct_ids, &match);
+#endif
+	if (np) {
+		mct_int_type = (u32)(match->data);
+
+		/* This driver uses only one global timer interrupt */
+		mct_irqs[MCT_G0_IRQ] = irq_of_parse_and_map(np, MCT_G0_IRQ);
+
+		/*
+		 * Find out the number of local irqs specified. The local
+		 * timer irqs are specified after the four global timer
+		 * irqs are specified.
+		 */
+#ifdef CONFIG_OF
+		nr_irqs = of_irq_count(np);
+#endif
+		for (i = MCT_L0_IRQ; i < nr_irqs; i++)
+			mct_irqs[i] = irq_of_parse_and_map(np, i);
+	} else if (soc_is_exynos4210()) {
 		mct_irqs[MCT_G0_IRQ] = EXYNOS4_IRQ_MCT_G0;
 		mct_irqs[MCT_L0_IRQ] = EXYNOS4_IRQ_MCT_L0;
 		mct_irqs[MCT_L1_IRQ] = EXYNOS4_IRQ_MCT_L1;
 		mct_int_type = MCT_INT_SPI;
-	} else if (soc_is_exynos5250()) {
-		mct_irqs[MCT_G0_IRQ] = EXYNOS5_IRQ_MCT_G0;
-		mct_irqs[MCT_L0_IRQ] = EXYNOS5_IRQ_MCT_L0;
-		mct_irqs[MCT_L1_IRQ] = EXYNOS5_IRQ_MCT_L1;
-		mct_int_type = MCT_INT_SPI;
 	} else {
-		mct_irqs[MCT_G0_IRQ] = EXYNOS4_IRQ_MCT_G0;
-		mct_irqs[MCT_L0_IRQ] = EXYNOS_IRQ_MCT_LOCALTIMER;
-		mct_int_type = MCT_INT_PPI;
+		panic("unable to determine mct controller type\n");
 	}
 
-	exynos4_timer_resources();
+	exynos4_timer_resources(np);
 	exynos4_clocksource_init();
 	exynos4_clockevent_init();
 }
-- 
1.7.5.4

[PATCH 4/7] ARM: Exynos: allow dt based discovery of mct controller using clocksource_of_init

[Thomas Abraham]

Add entries to __clksrc_of_table so that Exynos MCT controller is discoverable
using call to clocksource_of_init. With this change, it would be appropriate to
rename the function 'exynos4_timer_init' as 'mct_init' since it aptly describes
this function. Additionally, the 'init_time' callback of all machine descriptors
for exynos platforms that were previously set to 'exynos4_timer_init' are now
set to either 'mct_init' or 'clocksource_of_init'.

Cc: Changhwan Youn <chaos.youn@samsung.com> 
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
---
 arch/arm/mach-exynos/Kconfig           |    2 ++
 arch/arm/mach-exynos/common.h          |    2 +-
 arch/arm/mach-exynos/mach-armlex4210.c |    2 +-
 arch/arm/mach-exynos/mach-exynos4-dt.c |    3 ++-
 arch/arm/mach-exynos/mach-exynos5-dt.c |    3 ++-
 arch/arm/mach-exynos/mach-nuri.c       |    2 +-
 arch/arm/mach-exynos/mach-origen.c     |    2 +-
 arch/arm/mach-exynos/mach-smdk4x12.c   |    4 ++--
 arch/arm/mach-exynos/mach-smdkv310.c   |    4 ++--
 arch/arm/mach-exynos/mct.c             |   12 ++++++------
 10 files changed, 20 insertions(+), 16 deletions(-)

diff --git a/arch/arm/mach-exynos/Kconfig b/arch/arm/mach-exynos/Kconfig
index 7ea0579..e0ce082 100644
--- a/arch/arm/mach-exynos/Kconfig
+++ b/arch/arm/mach-exynos/Kconfig
@@ -418,6 +418,7 @@ config MACH_EXYNOS4_DT
 	select PINCTRL_EXYNOS4
 	select S5P_DEV_MFC
 	select USE_OF
+	select CLKSRC_OF
 	help
 	  Machine support for Samsung Exynos4 machine with device tree enabled.
 	  Select this if a fdt blob is available for the Exynos4 SoC based board.
@@ -430,6 +431,7 @@ config MACH_EXYNOS5_DT
 	depends on ARCH_EXYNOS5
 	select ARM_AMBA
 	select USE_OF
+	select CLKSRC_OF
 	help
 	  Machine support for Samsung EXYNOS5 machine with device tree enabled.
 	  Select this if a fdt blob is available for the EXYNOS5 SoC based board.
diff --git a/arch/arm/mach-exynos/common.h b/arch/arm/mach-exynos/common.h
index 3ab3c03..be3ea62 100644
--- a/arch/arm/mach-exynos/common.h
+++ b/arch/arm/mach-exynos/common.h
@@ -12,7 +12,7 @@
 #ifndef __ARCH_ARM_MACH_EXYNOS_COMMON_H
 #define __ARCH_ARM_MACH_EXYNOS_COMMON_H
 
-extern void exynos4_timer_init(void);
+extern void mct_init(void);
 
 struct map_desc;
 void exynos_init_io(struct map_desc *mach_desc, int size);
diff --git a/arch/arm/mach-exynos/mach-armlex4210.c b/arch/arm/mach-exynos/mach-armlex4210.c
index 2f18130..27b51d2 100644
--- a/arch/arm/mach-exynos/mach-armlex4210.c
+++ b/arch/arm/mach-exynos/mach-armlex4210.c
@@ -204,6 +204,6 @@ MACHINE_START(ARMLEX4210, "ARMLEX4210")
 	.handle_irq	= gic_handle_irq,
 	.init_machine	= armlex4210_machine_init,
 	.init_late	= exynos_init_late,
-	.init_time	= exynos4_timer_init,
+	.init_time	= mct_init,
 	.restart	= exynos4_restart,
 MACHINE_END
diff --git a/arch/arm/mach-exynos/mach-exynos4-dt.c b/arch/arm/mach-exynos/mach-exynos4-dt.c
index b68115a..19b42f2 100644
--- a/arch/arm/mach-exynos/mach-exynos4-dt.c
+++ b/arch/arm/mach-exynos/mach-exynos4-dt.c
@@ -15,6 +15,7 @@
 #include <linux/of_fdt.h>
 #include <linux/serial_core.h>
 #include <linux/memblock.h>
+#include <linux/clocksource.h>
 
 #include <asm/mach/arch.h>
 #include <asm/hardware/gic.h>
@@ -127,7 +128,7 @@ DT_MACHINE_START(EXYNOS4210_DT, "Samsung Exynos4 (Flattened Device Tree)")
 	.init_early	= exynos_firmware_init,
 	.init_machine	= exynos4_dt_machine_init,
 	.init_late	= exynos_init_late,
-	.init_time	= exynos4_timer_init,
+	.init_time	= clocksource_of_init,
 	.dt_compat	= exynos4_dt_compat,
 	.restart        = exynos4_restart,
 	.reserve	= exynos4_reserve,
diff --git a/arch/arm/mach-exynos/mach-exynos5-dt.c b/arch/arm/mach-exynos/mach-exynos5-dt.c
index d76bfba..591644b 100644
--- a/arch/arm/mach-exynos/mach-exynos5-dt.c
+++ b/arch/arm/mach-exynos/mach-exynos5-dt.c
@@ -14,6 +14,7 @@
 #include <linux/serial_core.h>
 #include <linux/memblock.h>
 #include <linux/io.h>
+#include <linux/clocksource.h>
 
 #include <asm/mach/arch.h>
 #include <asm/hardware/gic.h>
@@ -183,7 +184,7 @@ DT_MACHINE_START(EXYNOS5_DT, "SAMSUNG EXYNOS5 (Flattened Device Tree)")
 	.handle_irq	= gic_handle_irq,
 	.init_machine	= exynos5_dt_machine_init,
 	.init_late	= exynos_init_late,
-	.init_time	= exynos4_timer_init,
+	.init_time	= clocksource_of_init,
 	.dt_compat	= exynos5_dt_compat,
 	.restart        = exynos5_restart,
 	.reserve	= exynos5_reserve,
diff --git a/arch/arm/mach-exynos/mach-nuri.c b/arch/arm/mach-exynos/mach-nuri.c
index dccd1d1..e4a7ae5 100644
--- a/arch/arm/mach-exynos/mach-nuri.c
+++ b/arch/arm/mach-exynos/mach-nuri.c
@@ -1382,7 +1382,7 @@ MACHINE_START(NURI, "NURI")
 	.handle_irq	= gic_handle_irq,
 	.init_machine	= nuri_machine_init,
 	.init_late	= exynos_init_late,
-	.init_time	= exynos4_timer_init,
+	.init_time	= mct_init,
 	.reserve        = &nuri_reserve,
 	.restart	= exynos4_restart,
 MACHINE_END
diff --git a/arch/arm/mach-exynos/mach-origen.c b/arch/arm/mach-exynos/mach-origen.c
index 962c45f..c9de418 100644
--- a/arch/arm/mach-exynos/mach-origen.c
+++ b/arch/arm/mach-exynos/mach-origen.c
@@ -817,7 +817,7 @@ MACHINE_START(ORIGEN, "ORIGEN")
 	.handle_irq	= gic_handle_irq,
 	.init_machine	= origen_machine_init,
 	.init_late	= exynos_init_late,
-	.init_time	= exynos4_timer_init,
+	.init_time	= mct_init,
 	.reserve	= &origen_reserve,
 	.restart	= exynos4_restart,
 MACHINE_END
diff --git a/arch/arm/mach-exynos/mach-smdk4x12.c b/arch/arm/mach-exynos/mach-smdk4x12.c
index e9c9c29..a66e916e 100644
--- a/arch/arm/mach-exynos/mach-smdk4x12.c
+++ b/arch/arm/mach-exynos/mach-smdk4x12.c
@@ -378,7 +378,7 @@ MACHINE_START(SMDK4212, "SMDK4212")
 	.map_io		= smdk4x12_map_io,
 	.handle_irq	= gic_handle_irq,
 	.init_machine	= smdk4x12_machine_init,
-	.init_time	= exynos4_timer_init,
+	.init_time	= mct_init,
 	.restart	= exynos4_restart,
 	.reserve	= &smdk4x12_reserve,
 MACHINE_END
@@ -393,7 +393,7 @@ MACHINE_START(SMDK4412, "SMDK4412")
 	.handle_irq	= gic_handle_irq,
 	.init_machine	= smdk4x12_machine_init,
 	.init_late	= exynos_init_late,
-	.init_time	= exynos4_timer_init,
+	.init_time	= mct_init,
 	.restart	= exynos4_restart,
 	.reserve	= &smdk4x12_reserve,
 MACHINE_END
diff --git a/arch/arm/mach-exynos/mach-smdkv310.c b/arch/arm/mach-exynos/mach-smdkv310.c
index 13fa4a2..0245475 100644
--- a/arch/arm/mach-exynos/mach-smdkv310.c
+++ b/arch/arm/mach-exynos/mach-smdkv310.c
@@ -425,7 +425,7 @@ MACHINE_START(SMDKV310, "SMDKV310")
 	.map_io		= smdkv310_map_io,
 	.handle_irq	= gic_handle_irq,
 	.init_machine	= smdkv310_machine_init,
-	.init_time	= exynos4_timer_init,
+	.init_time	= mct_init,
 	.reserve	= &smdkv310_reserve,
 	.restart	= exynos4_restart,
 MACHINE_END
@@ -439,7 +439,7 @@ MACHINE_START(SMDKC210, "SMDKC210")
 	.handle_irq	= gic_handle_irq,
 	.init_machine	= smdkv310_machine_init,
 	.init_late	= exynos_init_late,
-	.init_time	= exynos4_timer_init,
+	.init_time	= mct_init,
 	.reserve	= &smdkv310_reserve,
 	.restart	= exynos4_restart,
 MACHINE_END
diff --git a/arch/arm/mach-exynos/mct.c b/arch/arm/mach-exynos/mct.c
index 524a859..e067130 100644
--- a/arch/arm/mach-exynos/mct.c
+++ b/arch/arm/mach-exynos/mct.c
@@ -22,6 +22,7 @@
 #include <linux/of.h>
 #include <linux/of_irq.h>
 #include <linux/of_address.h>
+#include <linux/clocksource.h>
 
 #include <asm/arch_timer.h>
 #include <asm/hardware/gic.h>
@@ -508,17 +509,12 @@ static const struct of_device_id exynos_mct_ids[] = {
 	{ .compatible = "samsung,exynos4412-mct", .data = (void *)MCT_INT_PPI },
 };
 
-void __init exynos4_timer_init(void)
+void __init mct_init(void)
 {
 	struct device_node *np = NULL;
 	const struct of_device_id *match;
 	u32 nr_irqs, i;
 
-	if (soc_is_exynos5440()) {
-		arch_timer_of_register();
-		return;
-	}
-
 #ifdef CONFIG_OF
 	np = of_find_matching_node_and_match(NULL, exynos_mct_ids, &match);
 #endif
@@ -551,3 +547,5 @@ void __init exynos4_timer_init(void)
 	exynos4_clocksource_init();
 	exynos4_clockevent_init();
 }
+CLOCKSOURCE_OF_DECLARE(exynos4210, "samsung,exynos4210-mct", mct_init)
+CLOCKSOURCE_OF_DECLARE(exynos4412, "samsung,exynos4412-mct", mct_init)
-- 
1.7.5.4

[PATCH 5/7] ARM: dts: add mct device tree node for all supported Exynos SoC's

[Thomas Abraham]

Add MCT device tree node for Exynos4210, Exynos4212, Exynos4412 and Exynos5250.

Cc: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
---
 arch/arm/boot/dts/exynos4210.dtsi |   22 ++++++++++++++++++++++
 arch/arm/boot/dts/exynos4212.dtsi |   22 ++++++++++++++++++++++
 arch/arm/boot/dts/exynos4412.dtsi |   24 ++++++++++++++++++++++++
 arch/arm/boot/dts/exynos5250.dtsi |   22 ++++++++++++++++++++++
 4 files changed, 90 insertions(+), 0 deletions(-)

diff --git a/arch/arm/boot/dts/exynos4210.dtsi b/arch/arm/boot/dts/exynos4210.dtsi
index 79ba247..0e16a34 100644
--- a/arch/arm/boot/dts/exynos4210.dtsi
+++ b/arch/arm/boot/dts/exynos4210.dtsi
@@ -47,6 +47,28 @@
 			     <0 12 0>, <0 13 0>, <0 14 0>, <0 15 0>;
 	};
 
+	mct@10050000 {
+		compatible = "samsung,exynos4210-mct";
+		reg = <0x10050000 0x800>;
+		interrupt-controller;
+		#interrups-cells = <2>;
+		interrupt-parent = <&mct_map>;
+		interrupts = <0 0>, <1 0>, <2 0>, <3 0>,
+			     <4 0>, <5 0>;
+
+		mct_map: mct-map {
+			#interrupt-cells = <2>;
+			#address-cells = <0>;
+			#size-cells = <0>;
+			interrupt-map = <0x0 0 &gic 0 57 0>,
+					<0x1 0 &gic 0 69 0>,
+					<0x2 0 &combiner 12 6>,
+					<0x3 0 &combiner 12 7>,
+					<0x4 0 &gic 0 42 0>,
+					<0x5 0 &gic 0 48 0>;
+		};
+	};
+
 	pmu {
 		compatible = "arm,cortex-a9-pmu";
 		interrupt-parent = <&combiner>;
diff --git a/arch/arm/boot/dts/exynos4212.dtsi b/arch/arm/boot/dts/exynos4212.dtsi
index c6ae200..36d4299 100644
--- a/arch/arm/boot/dts/exynos4212.dtsi
+++ b/arch/arm/boot/dts/exynos4212.dtsi
@@ -25,4 +25,26 @@
 	gic:interrupt-controller@10490000 {
 		cpu-offset = <0x8000>;
 	};
+
+	mct@10050000 {
+		compatible = "samsung,exynos4412-mct";
+		reg = <0x10050000 0x800>;
+		interrupt-controller;
+		#interrups-cells = <2>;
+		interrupt-parent = <&mct_map>;
+		interrupts = <0 0>, <1 0>, <2 0>, <3 0>,
+			     <4 0>, <5 0>;
+
+		mct_map: mct-map {
+			#interrupt-cells = <2>;
+			#address-cells = <0>;
+			#size-cells = <0>;
+			interrupt-map = <0x0 0 &gic 0 57 0>,
+					<0x1 0 &combiner 12 5>,
+					<0x2 0 &combiner 12 6>,
+					<0x3 0 &combiner 12 7>,
+					<0x4 0 &gic 1 12 0>,
+					<0x5 0 &gic 1 12 0>;
+		};
+	};
 };
diff --git a/arch/arm/boot/dts/exynos4412.dtsi b/arch/arm/boot/dts/exynos4412.dtsi
index d7dfe31..821c9fd 100644
--- a/arch/arm/boot/dts/exynos4412.dtsi
+++ b/arch/arm/boot/dts/exynos4412.dtsi
@@ -25,4 +25,28 @@
 	gic:interrupt-controller@10490000 {
 		cpu-offset = <0x4000>;
 	};
+
+	mct@10050000 {
+		compatible = "samsung,exynos4412-mct";
+		reg = <0x10050000 0x800>;
+		interrupt-controller;
+		#interrups-cells = <2>;
+		interrupt-parent = <&mct_map>;
+		interrupts = <0 0>, <1 0>, <2 0>, <3 0>,
+			     <4 0>, <5 0>, <6 0>, <7 0>;
+
+		mct_map: mct-map {
+			#interrupt-cells = <2>;
+			#address-cells = <0>;
+			#size-cells = <0>;
+			interrupt-map = <0x0 0 &gic 0 57 0>,
+					<0x1 0 &combiner 12 5>,
+					<0x2 0 &combiner 12 6>,
+					<0x3 0 &combiner 12 7>,
+					<0x4 0 &gic 1 12 0>,
+					<0x5 0 &gic 1 12 0>,
+					<0x6 0 &gic 1 12 0>,
+					<0x7 0 &gic 1 12 0>;
+		};
+	};
 };
diff --git a/arch/arm/boot/dts/exynos5250.dtsi b/arch/arm/boot/dts/exynos5250.dtsi
index 7c3d07a..8d8b5a0 100644
--- a/arch/arm/boot/dts/exynos5250.dtsi
+++ b/arch/arm/boot/dts/exynos5250.dtsi
@@ -79,6 +79,28 @@
 			     <0 28 0>, <0 29 0>, <0 30 0>, <0 31 0>;
 	};
 
+	mct@101C0000 {
+		compatible = "samsung,exynos4210-mct";
+		reg = <0x101C0000 0x800>;
+		interrupt-controller;
+		#interrups-cells = <2>;
+		interrupt-parent = <&mct_map>;
+		interrupts = <0 0>, <1 0>, <2 0>, <3 0>,
+			     <4 0>, <5 0>;
+
+		mct_map: mct-map {
+			#interrupt-cells = <2>;
+			#address-cells = <0>;
+			#size-cells = <0>;
+			interrupt-map = <0x0 0 &combiner 23 3>,
+					<0x1 0 &combiner 23 4>,
+					<0x2 0 &combiner 25 2>,
+					<0x3 0 &combiner 25 3>,
+					<0x4 0 &gic 0 120 0>,
+					<0x5 0 &gic 0 121 0>;
+		};
+	};
+
 	pmu {
 		compatible = "arm,cortex-a15-pmu";
 		interrupt-parent = <&combiner>;
-- 
1.7.5.4

[PATCH 6/7] ARM: Exynos: remove static io-remapping of mct registers for Exynos5

[Thomas Abraham]

With device tree support enabled for MCT controller, the staticio-remapping
of the MCT controller address space is removed for Exynos5 platforms (which
supports only device tree based boot).

Cc: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
---
 arch/arm/mach-exynos/common.c           |    5 -----
 arch/arm/mach-exynos/include/mach/map.h |    1 -
 2 files changed, 0 insertions(+), 6 deletions(-)

diff --git a/arch/arm/mach-exynos/common.c b/arch/arm/mach-exynos/common.c
index 4ce342e..3b6527b 100644
--- a/arch/arm/mach-exynos/common.c
+++ b/arch/arm/mach-exynos/common.c
@@ -283,11 +283,6 @@ static struct map_desc exynos5_iodesc[] __initdata = {
 		.length		= SZ_4K,
 		.type		= MT_DEVICE,
 	}, {
-		.virtual	= (unsigned long)S5P_VA_SYSTIMER,
-		.pfn		= __phys_to_pfn(EXYNOS5_PA_SYSTIMER),
-		.length		= SZ_4K,
-		.type		= MT_DEVICE,
-	}, {
 		.virtual	= (unsigned long)S5P_VA_SYSRAM,
 		.pfn		= __phys_to_pfn(EXYNOS5_PA_SYSRAM),
 		.length		= SZ_4K,
diff --git a/arch/arm/mach-exynos/include/mach/map.h b/arch/arm/mach-exynos/include/mach/map.h
index b8ea67e..99e0a79 100644
--- a/arch/arm/mach-exynos/include/mach/map.h
+++ b/arch/arm/mach-exynos/include/mach/map.h
@@ -68,7 +68,6 @@
 #define EXYNOS5_PA_CMU			0x10010000
 
 #define EXYNOS4_PA_SYSTIMER		0x10050000
-#define EXYNOS5_PA_SYSTIMER		0x101C0000
 
 #define EXYNOS4_PA_WATCHDOG		0x10060000
 #define EXYNOS5_PA_WATCHDOG		0x101D0000
-- 
1.7.5.4

[PATCH 7/7] ARM: Exynos: move mct driver to drivers/clocksource

[Thomas Abraham]

Move the multi core timer (mct) driver to from mach-exynos to
drivers/clocksource and update the Kconfig and makefiles.

Cc: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
---
 arch/arm/Kconfig                                   |    2 +-
 arch/arm/mach-exynos/Kconfig                       |    6 ------
 arch/arm/mach-exynos/Makefile                      |    2 --
 drivers/clocksource/Kconfig                        |    5 +++++
 drivers/clocksource/Makefile                       |    1 +
 .../mct.c => drivers/clocksource/exynos_mct.c      |    0
 6 files changed, 7 insertions(+), 9 deletions(-)
 rename arch/arm/mach-exynos/mct.c => drivers/clocksource/exynos_mct.c (100%)

diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 8b72d23..8234697 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -1622,7 +1622,7 @@ config LOCAL_TIMERS
 	bool "Use local timer interrupts"
 	depends on SMP
 	default y
-	select HAVE_ARM_TWD if (!ARCH_MSM_SCORPIONMP && !EXYNOS4_MCT)
+	select HAVE_ARM_TWD if (!ARCH_MSM_SCORPIONMP && !CLKSRC_EXYNOS_MCT)
 	help
 	  Enable support for local timers on SMP platforms, rather then the
 	  legacy IPI broadcast method.  Local timers allows the system
diff --git a/arch/arm/mach-exynos/Kconfig b/arch/arm/mach-exynos/Kconfig
index e0ce082..6961ac7 100644
--- a/arch/arm/mach-exynos/Kconfig
+++ b/arch/arm/mach-exynos/Kconfig
@@ -80,12 +80,6 @@ config SOC_EXYNOS5440
 	help
 	  Enable EXYNOS5440 SoC support
 
-config EXYNOS4_MCT
-	bool
-	default y
-	help
-	  Use MCT (Multi Core Timer) as kernel timers
-
 config EXYNOS_DEV_DMA
 	bool
 	help
diff --git a/arch/arm/mach-exynos/Makefile b/arch/arm/mach-exynos/Makefile
index 7e53a3a..5141963 100644
--- a/arch/arm/mach-exynos/Makefile
+++ b/arch/arm/mach-exynos/Makefile
@@ -26,8 +26,6 @@ obj-$(CONFIG_ARCH_EXYNOS)	+= pmu.o
 
 obj-$(CONFIG_SMP)		+= platsmp.o headsmp.o
 
-obj-$(CONFIG_EXYNOS4_MCT)	+= mct.o
-
 obj-$(CONFIG_HOTPLUG_CPU)	+= hotplug.o
 
 obj-$(CONFIG_ARCH_EXYNOS)	+= exynos-smc.o
diff --git a/drivers/clocksource/Kconfig b/drivers/clocksource/Kconfig
index a32b7a9..84bf4de 100644
--- a/drivers/clocksource/Kconfig
+++ b/drivers/clocksource/Kconfig
@@ -61,3 +61,8 @@ config CLKSRC_ARM_GENERIC
 	def_bool y if ARM64
 	help
 	  This option enables support for the ARM generic timer.
+
+config CLKSRC_EXYNOS_MCT
+	def_bool y if ARCH_EXYNOS
+	help
+	  Support for Multi Core Timer controller on Exynos SoCs.
diff --git a/drivers/clocksource/Makefile b/drivers/clocksource/Makefile
index a33f792..248a856 100644
--- a/drivers/clocksource/Makefile
+++ b/drivers/clocksource/Makefile
@@ -17,5 +17,6 @@ obj-$(CONFIG_CLKSRC_DBX500_PRCMU)	+= clksrc-dbx500-prcmu.o
 obj-$(CONFIG_ARMADA_370_XP_TIMER)	+= time-armada-370-xp.o
 obj-$(CONFIG_ARCH_BCM2835)	+= bcm2835_timer.o
 obj-$(CONFIG_SUNXI_TIMER)	+= sunxi_timer.o
+obj-$(CONFIG_CLKSRC_EXYNOS_MCT)	+= exynos_mct.o
 
 obj-$(CONFIG_CLKSRC_ARM_GENERIC)	+= arm_generic.o
diff --git a/arch/arm/mach-exynos/mct.c b/drivers/clocksource/exynos_mct.c
similarity index 100%
rename from arch/arm/mach-exynos/mct.c
rename to drivers/clocksource/exynos_mct.c
-- 
1.7.5.4