devicetree.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Sricharan R <r.sricharan@ti.com>
To: linux-omap@vger.kernel.org, linux-arm-kernel@lists.infradead.org
Cc: devicetree-discuss@lists.ozlabs.org, r.sricharan@ti.com,
	tony@atomide.com, b-cousson@ti.com
Subject: [PATCH V3 1/4] ARM: dts: omap5: Make uevm as the official board and deprecate sevm support
Date: Fri, 7 Jun 2013 18:52:47 +0530	[thread overview]
Message-ID: <1370611370-14715-2-git-send-email-r.sricharan@ti.com> (raw)
In-Reply-To: <1370611370-14715-1-git-send-email-r.sricharan@ti.com>

The uevm is the only official board supported for the OMAP5 soc
in mainline. The existent sevm platform will no more be supported.
Hence cleaning up the board dts file to have only the data
required for uevm.

Renaming the board dts file and adding the following cleanups.

 * There are no devices connected on I2C 2,3,4 buses. So remove
   the pinmux data for the same.

 * OMAP5432 and DDR3 memory is used in the uevm. Temperature polling
   is not supported with DDR3 memories. Because of DDR3 phy limitation
   the voltage change across DVFS and all shadow registers for DVFS on
   DDR3 is not supported. Hence the emif kernel driver is not required,
   so removing the DDR3 device file and emif nodes for uevm.

 * Keypad is not supported on uevm. So remove the device node.

Signed-off-by: Sricharan R <r.sricharan@ti.com>
---
 [V3] Rebased on top of Benoit's latest tip and improved the subject, changelog

 arch/arm/boot/dts/Makefile                         |    2 +-
 .../arm/boot/dts/{omap5-evm.dts => omap5-uevm.dts} |   83 +-------------------
 2 files changed, 4 insertions(+), 81 deletions(-)
 rename arch/arm/boot/dts/{omap5-evm.dts => omap5-uevm.dts} (73%)

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index bd388b1..8e50761 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -150,7 +150,7 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \
 	omap4-var-som.dtb \
 	omap4-sdp.dtb \
 	omap4-sdp-es23plus.dtb \
-	omap5-evm.dtb \
+	omap5-uevm.dtb \
 	am335x-evm.dtb \
 	am335x-evmsk.dtb \
 	am335x-bone.dtb \
diff --git a/arch/arm/boot/dts/omap5-evm.dts b/arch/arm/boot/dts/omap5-uevm.dts
similarity index 73%
rename from arch/arm/boot/dts/omap5-evm.dts
rename to arch/arm/boot/dts/omap5-uevm.dts
index 22e9ee8..843a001 100644
--- a/arch/arm/boot/dts/omap5-evm.dts
+++ b/arch/arm/boot/dts/omap5-uevm.dts
@@ -1,5 +1,5 @@
 /*
- * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
@@ -8,11 +8,10 @@
 /dts-v1/;
 
 #include "omap5.dtsi"
-#include "samsung_k3pe0e000b.dtsi"
 
 / {
-	model = "TI OMAP5 EVM board";
-	compatible = "ti,omap5-evm", "ti,omap5";
+	model = "TI OMAP5 uEVM board";
+	compatible = "ti,omap5-uevm", "ti,omap5";
 
 	memory {
 		device_type = "memory";
@@ -88,27 +87,6 @@
 		>;
 	};
 
-	i2c2_pins: pinmux_i2c2_pins {
-		pinctrl-single,pins = <
-			0x178 (PIN_INPUT | MUX_MODE0)		/* i2c2_scl */
-			0x17a (PIN_INPUT | MUX_MODE0)		/* i2c2_sda */
-		>;
-	};
-
-	i2c3_pins: pinmux_i2c3_pins {
-		pinctrl-single,pins = <
-			0x13a (PIN_INPUT | MUX_MODE0)		/* i2c3_scl */
-			0x13c (PIN_INPUT | MUX_MODE0)		/* i2c3_sda */
-		>;
-	};
-
-	i2c4_pins: pinmux_i2c4_pins {
-		pinctrl-single,pins = <
-			0xb8 (PIN_INPUT | MUX_MODE0)		/* i2c4_scl */
-			0xba (PIN_INPUT | MUX_MODE0)		/* i2c4_sda */
-		>;
-	};
-
 	i2c5_pins: pinmux_i2c5_pins {
 		pinctrl-single,pins = <
 			0x184 (PIN_INPUT | MUX_MODE0)		/* i2c5_scl */
@@ -175,39 +153,6 @@
 	clock-frequency = <400000>;
 };
 
-&i2c2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c2_pins>;
-
-	clock-frequency = <400000>;
-
-	/* Pressure Sensor */
-	bmp085@77 {
-		compatible = "bosch,bmp085";
-		reg = <0x77>;
-	};
-};
-
-&i2c3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c3_pins>;
-
-	clock-frequency = <400000>;
-};
-
-&i2c4 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c4_pins>;
-
-	clock-frequency = <400000>;
-
-	/* Temperature Sensor */
-	tmp102@48{
-		compatible = "ti,tmp102";
-		reg = <0x48>;
-	};
-};
-
 &i2c5 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c5_pins>;
@@ -215,32 +160,10 @@
 	clock-frequency = <400000>;
 };
 
-&keypad {
-	keypad,num-rows = <8>;
-	keypad,num-columns = <8>;
-	linux,keymap = <0x02020073	/* VOLUP */
-			0x02030072	/* VOLDOWM */
-			0x020400e7	/* SEND */
-			0x02050066	/* HOME */
-			0x0206006b	/* END */
-			0x020700d9>;	/* SEARCH */
-	linux,input-no-autorepeat;
-};
-
 &mcbsp3 {
 	status = "disabled";
 };
 
-&emif1 {
-	cs1-used;
-	device-handle = <&samsung_K3PE0E000B>;
-};
-
-&emif2 {
-	cs1-used;
-	device-handle = <&samsung_K3PE0E000B>;
-};
-
 &mcspi1 {
 
 };
-- 
1.7.9.5


  reply	other threads:[~2013-06-07 13:22 UTC|newest]

Thread overview: 7+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2013-06-07 13:22 [PATCH V3 0/4] ARM: dts: omap5: Cleanup and updates for DT files Sricharan R
2013-06-07 13:22 ` Sricharan R [this message]
2013-06-07 13:22 ` [PATCH V3 2/4] ARM: dts: omap5-uevm: Add USB Host support Sricharan R
2013-06-07 13:22 ` [PATCH V3 3/4] ARM: dts: omap5-uevm: Add LED support for uEVM blue LED Sricharan R
2013-06-07 13:22 ` [PATCH V3 4/4] ARM: dts: omap5-uevm: Add uart pinctrl data Sricharan R
2013-06-07 14:51 ` [PATCH V3 0/4] ARM: dts: omap5: Cleanup and updates for DT files Benoit Cousson
2013-06-07 15:46   ` Sricharan R

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1370611370-14715-2-git-send-email-r.sricharan@ti.com \
    --to=r.sricharan@ti.com \
    --cc=b-cousson@ti.com \
    --cc=devicetree-discuss@lists.ozlabs.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-omap@vger.kernel.org \
    --cc=tony@atomide.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).