From: Rahul Sharma <rahul.sharma@samsung.com>
To: linux-samsung-soc@vger.kernel.org, devicetree@vger.kernel.org
Cc: kgene.kim@samsung.com, sw0312.kim@samsung.com,
inki.dae@samsung.com, tomasz.figa@gmail.com,
s.nawrocki@samsung.com, joshi@samsung.com, r.sh.open@gmail.com,
Rahul Sharma <rahul.sharma@samsung.com>
Subject: [PATCH v6 1/7] of/documentation: update with clock information for exynos hdmi subsystem
Date: Thu, 29 Aug 2013 10:44:54 +0530 [thread overview]
Message-ID: <1377753300-9118-2-git-send-email-rahul.sharma@samsung.com> (raw)
In-Reply-To: <1377753300-9118-1-git-send-email-rahul.sharma@samsung.com>
Adding information about clocks to the binding documentation
for exynos mixer and hdmi.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
---
Documentation/devicetree/bindings/video/exynos_hdmi.txt | 15 ++++++++++++++-
.../devicetree/bindings/video/exynos_mixer.txt | 4 ++++
2 files changed, 18 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/video/exynos_hdmi.txt b/Documentation/devicetree/bindings/video/exynos_hdmi.txt
index 323983b..1878418 100644
--- a/Documentation/devicetree/bindings/video/exynos_hdmi.txt
+++ b/Documentation/devicetree/bindings/video/exynos_hdmi.txt
@@ -12,7 +12,20 @@ Required properties:
a) phandle of the gpio controller node.
b) pin number within the gpio controller.
c) optional flags and pull up/down.
-
+- clocks: list of clock IDs from SoC clock driver.
+ a) hdmi: It is required for gate operation on aclk_200_disp1 clock
+ which clocks the display1 block.
+ b) sclk_hdmi: Gate of HDMI special clock.
+ c) sclk_pixel: Pixel special clock, one of the two possible inputs of
+ HDMI clock mux.
+ d) sclk_hdmiphy: HDMI PHY clock output, one of two possible inputs of
+ HDMI clock mux.
+ e) mout_hdmi: It is required by the driver to switch between the 2
+ parents i.e. sclk_pixel and sclk_hdmiphy. If hdmiphy is stable
+ after configuration, parent is set to sclk_hdmiphy else
+ sclk_pixel.
+- clock-names: aliases as per driver requirements for above clock IDs:
+ "hdmi", "sclk_hdmi", "sclk_pixel", "sclk_hdmiphy" and "mout_hdmi".
Example:
hdmi {
diff --git a/Documentation/devicetree/bindings/video/exynos_mixer.txt b/Documentation/devicetree/bindings/video/exynos_mixer.txt
index 3334b0a..7bfde9c 100644
--- a/Documentation/devicetree/bindings/video/exynos_mixer.txt
+++ b/Documentation/devicetree/bindings/video/exynos_mixer.txt
@@ -10,6 +10,10 @@ Required properties:
- reg: physical base address of the mixer and length of memory mapped
region.
- interrupts: interrupt number to the cpu.
+- clocks: list of clock IDs from SoC clock driver.
+ a) mixer: Gate of Mixer IP bus clock.
+ b) sclk_hdmi: HDMI Special clock, one of the two possible inputs of
+ mixer mux.
Example:
--
1.7.10.4
next prev parent reply other threads:[~2013-08-29 5:14 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-08-29 5:14 [PATCH v6 0/7] ARM: dts: add support for exynos hdmi subsystem Rahul Sharma
2013-08-29 5:14 ` Rahul Sharma [this message]
2013-08-29 5:14 ` [PATCH v6 2/7] ARM: dts: add mixer clocks to mixer node for Exynos5250 Rahul Sharma
2013-08-29 5:14 ` [PATCH v6 3/7] ARM: dts: add clocks to hdmi dt node for exynos5250 Rahul Sharma
2013-08-29 5:14 ` [PATCH v6 4/7] ARM: dts: add i2c device nodes for Exynos5420 Rahul Sharma
2013-08-29 5:14 ` [PATCH v6 5/7] ARM: dts: add dt nodes for hdmi subsystem for exynos5420 Rahul Sharma
2013-08-29 5:14 ` [PATCH v6 6/7] ARM: dts: add hdmi hpd gpio pinctrl node for exynos5420 smdk board Rahul Sharma
2013-08-29 5:15 ` [PATCH v6 7/7] ARM: dts: add hdmi ddc device " Rahul Sharma
-- strict thread matches above, loose matches on Subject: below --
2013-08-29 5:40 [PATCH v6 0/7] ARM: dts: add support for exynos hdmi subsystem Rahul Sharma
2013-08-29 5:40 ` [PATCH v6 1/7] of/documentation: update with clock information " Rahul Sharma
2013-08-29 12:59 ` Tomasz Figa
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1377753300-9118-2-git-send-email-rahul.sharma@samsung.com \
--to=rahul.sharma@samsung.com \
--cc=devicetree@vger.kernel.org \
--cc=inki.dae@samsung.com \
--cc=joshi@samsung.com \
--cc=kgene.kim@samsung.com \
--cc=linux-samsung-soc@vger.kernel.org \
--cc=r.sh.open@gmail.com \
--cc=s.nawrocki@samsung.com \
--cc=sw0312.kim@samsung.com \
--cc=tomasz.figa@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).