devicetree.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Rahul Sharma <rahul.sharma@samsung.com>
To: linux-samsung-soc@vger.kernel.org, devicetree@vger.kernel.org
Cc: kgene.kim@samsung.com, sw0312.kim@samsung.com,
	inki.dae@samsung.com, tomasz.figa@gmail.com,
	s.nawrocki@samsung.com, joshi@samsung.com, r.sh.open@gmail.com,
	Rahul Sharma <rahul.sharma@samsung.com>
Subject: [PATCH v7 1/6] of/documentation: update with clock information for exynos hdmi subsystem
Date: Thu, 29 Aug 2013 19:22:52 +0530	[thread overview]
Message-ID: <1377784377-28426-2-git-send-email-rahul.sharma@samsung.com> (raw)
In-Reply-To: <1377784377-28426-1-git-send-email-rahul.sharma@samsung.com>

Adding information about clocks to the binding documentation
for exynos mixer and hdmi.

Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
---
 Documentation/devicetree/bindings/video/exynos_hdmi.txt  |   14 +++++++++++++-
 Documentation/devicetree/bindings/video/exynos_mixer.txt |    4 ++++
 2 files changed, 17 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/video/exynos_hdmi.txt b/Documentation/devicetree/bindings/video/exynos_hdmi.txt
index 323983b..50decf8 100644
--- a/Documentation/devicetree/bindings/video/exynos_hdmi.txt
+++ b/Documentation/devicetree/bindings/video/exynos_hdmi.txt
@@ -12,7 +12,19 @@ Required properties:
 	a) phandle of the gpio controller node.
 	b) pin number within the gpio controller.
 	c) optional flags and pull up/down.
-
+- clocks: list of clock IDs from SoC clock driver.
+	a) hdmi: Gate of HDMI IP bus clock.
+	b) sclk_hdmi: Gate of HDMI special clock.
+	c) sclk_pixel: Pixel special clock, one of the two possible inputs of
+		HDMI clock mux.
+	d) sclk_hdmiphy: HDMI PHY clock output, one of two possible inputs of
+		HDMI clock mux.
+	e) mout_hdmi: It is required by the driver to switch between the 2
+		parents i.e. sclk_pixel and sclk_hdmiphy. If hdmiphy is stable
+		after configuration, parent is set to sclk_hdmiphy else
+		sclk_pixel.
+- clock-names: aliases as per driver requirements for above clock IDs:
+	"hdmi", "sclk_hdmi", "sclk_pixel", "sclk_hdmiphy" and "mout_hdmi".
 Example:
 
 	hdmi {
diff --git a/Documentation/devicetree/bindings/video/exynos_mixer.txt b/Documentation/devicetree/bindings/video/exynos_mixer.txt
index 3334b0a..7bfde9c 100644
--- a/Documentation/devicetree/bindings/video/exynos_mixer.txt
+++ b/Documentation/devicetree/bindings/video/exynos_mixer.txt
@@ -10,6 +10,10 @@ Required properties:
 - reg: physical base address of the mixer and length of memory mapped
 	region.
 - interrupts: interrupt number to the cpu.
+- clocks: list of clock IDs from SoC clock driver.
+	a) mixer: Gate of Mixer IP bus clock.
+	b) sclk_hdmi: HDMI Special clock, one of the two possible inputs of
+               mixer mux.
 
 Example:
 
-- 
1.7.10.4

  parent reply	other threads:[~2013-08-29 13:52 UTC|newest]

Thread overview: 10+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2013-08-29 13:52 [PATCH v7 0/6] ARM: dts: add support for exynos hdmi subsystem Rahul Sharma
2013-08-29 13:35 ` Tomasz Figa
2013-08-30  4:43   ` Rahul Sharma
     [not found]     ` <CAPdUM4N7DeBkO8Dt859toB92SRskBc8wkGDCNJXt4Fz=YXSOBg-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2013-09-30  7:51       ` Kukjin Kim
2013-08-29 13:52 ` Rahul Sharma [this message]
2013-08-29 13:52 ` [PATCH v7 2/6] ARM: dts: add mixer clocks to mixer node for Exynos5250 Rahul Sharma
2013-08-29 13:52 ` [PATCH v7 3/6] ARM: dts: add clocks to hdmi dt node for exynos5250 Rahul Sharma
2013-08-29 13:52 ` [PATCH v7 4/6] ARM: dts: add i2c device nodes for Exynos5420 Rahul Sharma
2013-08-29 13:52 ` [PATCH v7 5/6] ARM: dts: add dt nodes for hdmi subsystem for exynos5420 Rahul Sharma
2013-08-29 13:52 ` [PATCH v7 6/6] ARM: dts: enable hdmi subsystem for exynos5420 smdk board Rahul Sharma

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1377784377-28426-2-git-send-email-rahul.sharma@samsung.com \
    --to=rahul.sharma@samsung.com \
    --cc=devicetree@vger.kernel.org \
    --cc=inki.dae@samsung.com \
    --cc=joshi@samsung.com \
    --cc=kgene.kim@samsung.com \
    --cc=linux-samsung-soc@vger.kernel.org \
    --cc=r.sh.open@gmail.com \
    --cc=s.nawrocki@samsung.com \
    --cc=sw0312.kim@samsung.com \
    --cc=tomasz.figa@gmail.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).