From mboxrd@z Thu Jan 1 00:00:00 1970 From: Arun Kumar K Subject: [PATCH v10 11/12] V4L: Add DT binding doc for s5k4e5 image sensor Date: Fri, 18 Oct 2013 11:07:38 +0530 Message-ID: <1382074659-31130-12-git-send-email-arun.kk@samsung.com> References: <1382074659-31130-1-git-send-email-arun.kk@samsung.com> Return-path: In-Reply-To: <1382074659-31130-1-git-send-email-arun.kk@samsung.com> Sender: linux-media-owner@vger.kernel.org To: linux-media@vger.kernel.org, linux-samsung-soc@vger.kernel.org, devicetree@vger.kernel.org Cc: s.nawrocki@samsung.com, hverkuil@xs4all.nl, swarren@wwwdotorg.org, mark.rutland@arm.com, Pawel.Moll@arm.com, galak@codeaurora.org, a.hajda@samsung.com, sachin.kamat@linaro.org, shaik.ameer@samsung.com, kilyeon.im@samsung.com, arunkk.samsung@gmail.com List-Id: devicetree@vger.kernel.org S5K4E5 is a Samsung raw image sensor controlled via I2C. This patch adds the DT binding documentation for the same. Signed-off-by: Arun Kumar K Reviewed-by: Sylwester Nawrocki --- .../devicetree/bindings/media/samsung-s5k4e5.txt | 45 ++++++++++++++++++++ 1 file changed, 45 insertions(+) create mode 100644 Documentation/devicetree/bindings/media/samsung-s5k4e5.txt diff --git a/Documentation/devicetree/bindings/media/samsung-s5k4e5.txt b/Documentation/devicetree/bindings/media/samsung-s5k4e5.txt new file mode 100644 index 0000000..0fca087 --- /dev/null +++ b/Documentation/devicetree/bindings/media/samsung-s5k4e5.txt @@ -0,0 +1,45 @@ +* Samsung S5K4E5 Raw Image Sensor + +S5K4E5 is a raw image sensor with maximum resolution of 2560x1920 +pixels. Data transfer is carried out via MIPI CSI-2 port and controls +via I2C bus. + +Required Properties: +- compatible : must be "samsung,s5k4e5" +- reg : I2C device address +- reset-gpios : specifier of a GPIO connected to the RESET pin +- clocks : should contain the sensor's EXTCLK clock specifier, from + the common clock bindings +- clock-names : should contain "extclk" entry +- svdda-supply : core voltage supply +- svddio-supply : I/O voltage supply + +Optional Properties: +- clock-frequency : the frequency at which the "extclk" clock should be + configured to operate, in Hz; if this property is not + specified default 24 MHz value will be used + +The device node should be added to respective control bus controller +(e.g. I2C0) nodes and linked to the csis port node, using the common +video interfaces bindings, defined in video-interfaces.txt. + +Example: + + i2c-isp@13130000 { + s5k4e5@20 { + compatible = "samsung,s5k4e5"; + reg = <0x20>; + reset-gpios = <&gpx1 2 1>; + clock-frequency = <24000000>; + clocks = <&clock 129>; + clock-names = "extclk" + svdda-supply = <...>; + svddio-supply = <...>; + port { + is_s5k4e5_ep: endpoint { + data-lanes = <1 2 3 4>; + remote-endpoint = <&csis0_ep>; + }; + }; + }; + }; -- 1.7.9.5