From: Yuvaraj Kumar C D <yuvaraj.cd@gmail.com>
To: kishon@ti.com, kgene.kim@samsung.com,
linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
linux-doc@vger.kernel.org
Cc: mark.rutland@arm.com, jg1.han@samsung.com,
b.zolnierkie@samsung.com, joshi@samsung.com, t.figa@samsung.com,
swarren@wwwdotorg.org, rob.herring@calxeda.com,
grant.likely@linaro.org, christoffer.dall@linaro.org,
linux-ide@vger.kernel.org,
Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Subject: [PATCH V5 2/2] ARM: dts: Enable ahci sata and sata phy
Date: Thu, 9 Jan 2014 15:36:45 +0530 [thread overview]
Message-ID: <1389262005-30399-3-git-send-email-yuvaraj.cd@samsung.com> (raw)
In-Reply-To: <1389262005-30399-1-git-send-email-yuvaraj.cd@samsung.com>
This patch adds dt entry for ahci sata controller and its
corresponding phy controller.phy node has been added w.r.t
new generic phy framework.
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
---
Changes since V4:
1.Used the new phandle "sata_phy_i2c" in the DT entry.
2.Updated binding document.
Changes since V3:
1.Moved the binding info to the /bindings/phy/
Changes since V2:
1.Used syscon interface to PMU handling.
2.Changed "sata-phy-i2c" to "exynos-sataphy-i2c".
Changes since V1:
1.Minor changes to node name convention.
2.Updated binding document.
.../devicetree/bindings/ata/exynos-sata-phy.txt | 14 --------
.../devicetree/bindings/ata/exynos-sata.txt | 25 +++++++++-----
.../devicetree/bindings/phy/samsung-phy.txt | 36 ++++++++++++++++++++
arch/arm/boot/dts/exynos5250-arndale.dts | 11 ++++++
arch/arm/boot/dts/exynos5250-smdk5250.dts | 8 ++---
arch/arm/boot/dts/exynos5250.dtsi | 17 ++++++---
6 files changed, 78 insertions(+), 33 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/ata/exynos-sata-phy.txt
diff --git a/Documentation/devicetree/bindings/ata/exynos-sata-phy.txt b/Documentation/devicetree/bindings/ata/exynos-sata-phy.txt
deleted file mode 100644
index 37824fa..0000000
--- a/Documentation/devicetree/bindings/ata/exynos-sata-phy.txt
+++ /dev/null
@@ -1,14 +0,0 @@
-* Samsung SATA PHY Controller
-
-SATA PHY nodes are defined to describe on-chip SATA Physical layer controllers.
-Each SATA PHY controller should have its own node.
-
-Required properties:
-- compatible : compatible list, contains "samsung,exynos5-sata-phy"
-- reg : <registers mapping>
-
-Example:
- sata@ffe07000 {
- compatible = "samsung,exynos5-sata-phy";
- reg = <0xffe07000 0x1000>;
- };
diff --git a/Documentation/devicetree/bindings/ata/exynos-sata.txt b/Documentation/devicetree/bindings/ata/exynos-sata.txt
index 0849f10..b2adb1f 100644
--- a/Documentation/devicetree/bindings/ata/exynos-sata.txt
+++ b/Documentation/devicetree/bindings/ata/exynos-sata.txt
@@ -4,14 +4,21 @@ SATA nodes are defined to describe on-chip Serial ATA controllers.
Each SATA controller should have its own node.
Required properties:
-- compatible : compatible list, contains "samsung,exynos5-sata"
-- interrupts : <interrupt mapping for SATA IRQ>
-- reg : <registers mapping>
-- samsung,sata-freq : <frequency in MHz>
+- compatible : compatible list, contains "samsung,exynos5-sata"
+- interrupts : <interrupt mapping for SATA IRQ>
+- reg : <registers mapping>
+- samsung,sata-freq : <frequency in MHz>
+- phys : as mentioned in phy-bindings.txt
+- phy-names : as mentioned in phy-bindings.txt
Example:
- sata@ffe08000 {
- compatible = "samsung,exynos5-sata";
- reg = <0xffe08000 0x1000>;
- interrupts = <115>;
- };
+ sata@122f0000 {
+ compatible = "snps,dwc-ahci";
+ samsung,sata-freq = <66>;
+ reg = <0x122f0000 0x1ff>;
+ interrupts = <0 115 0>;
+ clocks = <&clock 277>, <&clock 143>;
+ clock-names = "sata", "sclk_sata";
+ phys = <&sata_phy>;
+ phy-names = "sata-phy";
+ };
diff --git a/Documentation/devicetree/bindings/phy/samsung-phy.txt b/Documentation/devicetree/bindings/phy/samsung-phy.txt
index c0fccaa..a937f75 100644
--- a/Documentation/devicetree/bindings/phy/samsung-phy.txt
+++ b/Documentation/devicetree/bindings/phy/samsung-phy.txt
@@ -20,3 +20,39 @@ Required properties:
- compatible : should be "samsung,exynos5250-dp-video-phy";
- reg : offset and length of the Display Port PHY register set;
- #phy-cells : from the generic PHY bindings, must be 0;
+
+Samsung SATA PHY Controller
+---------------------------
+
+SATA PHY nodes are defined to describe on-chip SATA Physical layer controllers.
+Each SATA PHY controller should have its own node.
+
+Required properties:
+- compatible : compatible list, contains "samsung,exynos5250-sata-phy"
+- reg : offset and length of the SATA PHY register set;
+- #phy-cells : from the generic phy bindings;
+
+Example:
+ sata_phy: sata-phy@12170000 {
+ compatible = "samsung,exynos5250-sata-phy";
+ reg = <0x12170000 0x1ff>;
+ clocks = <&clock 287>;
+ clock-names = "sata_phyctrl";
+ #phy-cells = <0>;
+ samsung,exynos-sataphy-i2c-phandle = <&sata_phy_i2c>;
+ samsung,syscon-phandle = <&pmu_syscon>;
+ };
+
+Device-Tree bindings for sataphy i2c client driver
+--------------------------------------------------
+
+Required properties:
+compatible: Should be "samsung,exynos-sataphy-i2c"
+- reg: I2C address of the sataphy i2c device.
+
+Example:
+
+ sata_phy_i2c:sata-phy@38 {
+ compatible = "samsung,exynos-sataphy-i2c";
+ reg = <0x38>;
+ };
diff --git a/arch/arm/boot/dts/exynos5250-arndale.dts b/arch/arm/boot/dts/exynos5250-arndale.dts
index b42e658..d9c9eaf 100644
--- a/arch/arm/boot/dts/exynos5250-arndale.dts
+++ b/arch/arm/boot/dts/exynos5250-arndale.dts
@@ -370,6 +370,17 @@
};
};
+ i2c@121D0000 {
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <40000>;
+ samsung,i2c-slave-addr = <0x38>;
+
+ sata_phy_i2c:sata-phy@38 {
+ compatible = "samsung,exynos-sataphy-i2c";
+ reg = <0x38>;
+ };
+ };
+
mmc_0: mmc@12200000 {
status = "okay";
num-slots = <1>;
diff --git a/arch/arm/boot/dts/exynos5250-smdk5250.dts b/arch/arm/boot/dts/exynos5250-smdk5250.dts
index 3e69837..e52eed8 100644
--- a/arch/arm/boot/dts/exynos5250-smdk5250.dts
+++ b/arch/arm/boot/dts/exynos5250-smdk5250.dts
@@ -96,16 +96,12 @@
samsung,i2c-slave-addr = <0x38>;
status = "okay";
- sata-phy {
- compatible = "samsung,sata-phy";
+ sata_phy_i2c:sata-phy@38 {
+ compatible = "samsung,exynos-sataphy-i2c";
reg = <0x38>;
};
};
- sata@122F0000 {
- samsung,sata-freq = <66>;
- };
-
i2c@12C80000 {
samsung,i2c-sda-delay = <100>;
samsung,i2c-max-bus-freq = <66000>;
diff --git a/arch/arm/boot/dts/exynos5250.dtsi b/arch/arm/boot/dts/exynos5250.dtsi
index dbb4a47..550d59e 100644
--- a/arch/arm/boot/dts/exynos5250.dtsi
+++ b/arch/arm/boot/dts/exynos5250.dtsi
@@ -46,6 +46,7 @@
i2c6 = &i2c_6;
i2c7 = &i2c_7;
i2c8 = &i2c_8;
+ i2c9 = &i2c_9;
pinctrl0 = &pinctrl_0;
pinctrl1 = &pinctrl_1;
pinctrl2 = &pinctrl_2;
@@ -231,16 +232,24 @@
};
sata@122F0000 {
- compatible = "samsung,exynos5-sata-ahci";
+ compatible = "snps,dwc-ahci";
+ samsung,sata-freq = <66>;
reg = <0x122F0000 0x1ff>;
interrupts = <0 115 0>;
clocks = <&clock 277>, <&clock 143>;
clock-names = "sata", "sclk_sata";
+ phys = <&sata_phy>;
+ phy-names = "sata-phy";
};
- sata-phy@12170000 {
- compatible = "samsung,exynos5-sata-phy";
+ sata_phy: sata-phy@12170000 {
+ compatible = "samsung,exynos5250-sata-phy";
reg = <0x12170000 0x1ff>;
+ clocks = <&clock 287>;
+ clock-names = "sata_phyctrl";
+ #phy-cells = <0>;
+ samsung,exynos-sataphy-i2c-phandle = <&sata_phy_i2c>;
+ samsung,syscon-phandle = <&pmu_syscon>;
};
i2c_0: i2c@12C60000 {
@@ -358,7 +367,7 @@
status = "disabled";
};
- i2c@121D0000 {
+ i2c_9: i2c@121D0000 {
compatible = "samsung,exynos5-sata-phy-i2c";
reg = <0x121D0000 0x100>;
#address-cells = <1>;
--
1.7.9.5
prev parent reply other threads:[~2014-01-09 10:06 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-01-09 10:06 [PATCH V5 0/2] Exynos5250 SATA Support Yuvaraj Kumar C D
2014-01-09 10:06 ` [PATCH V5 1/2] PHY: Exynos: Add Exynos5250 SATA PHY driver Yuvaraj Kumar C D
2014-01-10 1:16 ` Jingoo Han
2014-01-09 10:06 ` Yuvaraj Kumar C D [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1389262005-30399-3-git-send-email-yuvaraj.cd@samsung.com \
--to=yuvaraj.cd@gmail.com \
--cc=b.zolnierkie@samsung.com \
--cc=christoffer.dall@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=grant.likely@linaro.org \
--cc=jg1.han@samsung.com \
--cc=joshi@samsung.com \
--cc=kgene.kim@samsung.com \
--cc=kishon@ti.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-doc@vger.kernel.org \
--cc=linux-ide@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=rob.herring@calxeda.com \
--cc=swarren@wwwdotorg.org \
--cc=t.figa@samsung.com \
--cc=yuvaraj.cd@samsung.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).