[PATCH 1/6] pci-rcar-gen2: add initial device tree documentation

[PATCH 1/6] pci-rcar-gen2: add initial device tree documentation

[Ben Dooks]

Add initial documentation for the pci-rcar-gen2 driver device tree bindings.
This is not yet complete and needs work on the sub-nodes for the PCI bus.

Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
---
Cc: linux-sh@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: horms+renesas@verge.net.au
---
 Documentation/devicetree/bindings/pci/renessas,pci-r8a7790 | 12 ++++++++++++
 1 file changed, 12 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pci/renessas,pci-r8a7790

diff --git a/Documentation/devicetree/bindings/pci/renessas,pci-r8a7790 b/Documentation/devicetree/bindings/pci/renessas,pci-r8a7790
new file mode 100644
index 0000000..65268d9
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/renessas,pci-r8a7790
@@ -0,0 +1,12 @@
+Renesas internal AHB to PCI bridge
+
+This is the bridge used internally to connect the USB controllers to the
+AHB.
+
+Required properties:
+ - compatible: "renesas,pci-r8a7790" for the R8A7790 SoC
+ - reg : A list of physical regions to access the device. The first is
+         the operational registers for the OHCI/EHCI controller and the
+	 second region is for the bridge configuration and control registers.
+ - interrupts : interrupt for the device
+ - clocks : The reference to the device clock
\ No newline at end of file
-- 
1.8.5.2

[PATCH] pci-rcar-gen2: add of match table

[Ben Dooks]

Add OF match table for pci-rcar-gen2 driver for device tree support.

Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
---
Cc: Bjorn Helgaas <bhelgaas@google.com> (supporter:PCI SUBSYSTEM)
Cc: Simon Horman <horms@verge.net.au> (maintainer:PCI DRIVER FOR RE...)
Cc: linux-pci@vger.kernel.org (open list:PCI DRIVER FOR RE...)
Cc: linux-sh@vger.kernel.org (open list:PCI DRIVER FOR RE...)
Cc: devicetree@vger.kernel.org (open list:OPEN FIRMWARE AND...)
---
 drivers/pci/host/pci-rcar-gen2.c | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/drivers/pci/host/pci-rcar-gen2.c b/drivers/pci/host/pci-rcar-gen2.c
index ceec147..ea65bac 100644
--- a/drivers/pci/host/pci-rcar-gen2.c
+++ b/drivers/pci/host/pci-rcar-gen2.c
@@ -311,9 +311,17 @@ static int __init rcar_pci_probe(struct platform_device *pdev)
 	return rcar_pci_add_controller(priv);
 }
 
+static struct of_device_id rcar_pci_of_match[] = {
+	{ .compatible = "renesas,pci-r8a7790", },
+	{ },
+};
+
+MODULE_DEVICE_TABLE(of, rcar_pci_of_match);
+
 static struct platform_driver rcar_pci_driver = {
 	.driver = {
 		.name = "pci-rcar-gen2",
+		.of_match_table = rcar_pci_of_match,
 	},
 };
 
-- 
1.8.5.2

Re: [PATCH 1/6] pci-rcar-gen2: add initial device tree documentation

[Sergei Shtylyov]

Hello.

On 18-01-2014 19:03, Ben Dooks wrote:

> Add initial documentation for the pci-rcar-gen2 driver device tree bindings.
> This is not yet complete and needs work on the sub-nodes for the PCI bus.

    Why do you think there's a need to document PCI devices? They're 
auto-dicoverable and not usually described in .dts[i] files.

> Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
> ---
> Cc: linux-sh@vger.kernel.org
> Cc: devicetree@vger.kernel.org
> Cc: horms+renesas@verge.net.au
> ---
>   Documentation/devicetree/bindings/pci/renessas,pci-r8a7790 | 12 ++++++++++++

    Just "renesas", not "renessas". Also, .txt file extension is always used 
for bindings as much as I could observe.

>   1 file changed, 12 insertions(+)
>   create mode 100644 Documentation/devicetree/bindings/pci/renessas,pci-r8a7790

> diff --git a/Documentation/devicetree/bindings/pci/renessas,pci-r8a7790 b/Documentation/devicetree/bindings/pci/renessas,pci-r8a7790
> new file mode 100644
> index 0000000..65268d9
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pci/renessas,pci-r8a7790
> @@ -0,0 +1,12 @@
> +Renesas internal AHB to PCI bridge
> +
> +This is the bridge used internally to connect the USB controllers to the
> +AHB.
> +
> +Required properties:
> + - compatible: "renesas,pci-r8a7790" for the R8A7790 SoC
> + - reg : A list of physical regions to access the device. The first is
> +         the operational registers for the OHCI/EHCI controller and the

    What?! This resource doesn't belong to the bridge itself. Perhaps it's a 
candidate for the "ranges" property.

> +	 second region is for the bridge configuration and control registers.
> + - interrupts : interrupt for the device
> + - clocks : The reference to the device clock
> \ No newline at end of file

    Please add it.

WBR, Sergei

Re: [PATCH 1/6] pci-rcar-gen2: add initial device tree documentation

[Ben Dooks]

On 18/01/14 19:25, Sergei Shtylyov wrote:
> Hello.
>
> On 18-01-2014 19:03, Ben Dooks wrote:
>
>> Add initial documentation for the pci-rcar-gen2 driver device tree
>> bindings.
>> This is not yet complete and needs work on the sub-nodes for the PCI bus.

>     Why do you think there's a need to document PCI devices? They're
> auto-dicoverable and not usually described in .dts[i] files.

Because the bridge nodes are not auto-discoverable.

>> Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
>> ---
>> Cc: linux-sh@vger.kernel.org
>> Cc: devicetree@vger.kernel.org
>> Cc: horms+renesas@verge.net.au
>> ---
>>   Documentation/devicetree/bindings/pci/renessas,pci-r8a7790 | 12
>> ++++++++++++
>
>     Just "renesas", not "renessas". Also, .txt file extension is always
> used for bindings as much as I could observe.

Thanks, will fix.

>>   1 file changed, 12 insertions(+)
>>   create mode 100644
>> Documentation/devicetree/bindings/pci/renessas,pci-r8a7790
>
>> diff --git
>> a/Documentation/devicetree/bindings/pci/renessas,pci-r8a7790
>> b/Documentation/devicetree/bindings/pci/renessas,pci-r8a7790
>> new file mode 100644
>> index 0000000..65268d9
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/pci/renessas,pci-r8a7790
>> @@ -0,0 +1,12 @@
>> +Renesas internal AHB to PCI bridge
>> +
>> +This is the bridge used internally to connect the USB controllers to the
>> +AHB.
>> +
>> +Required properties:
>> + - compatible: "renesas,pci-r8a7790" for the R8A7790 SoC
>> + - reg : A list of physical regions to access the device. The first is
>> +         the operational registers for the OHCI/EHCI controller and the
>
>     What?! This resource doesn't belong to the bridge itself. Perhaps
> it's a candidate for the "ranges" property.

Will look into that one.

-- 
Ben Dooks				http://www.codethink.co.uk/
Senior Engineer				Codethink - Providing Genius

[PATCH 2/6] ARM: shmbobile: r8a7790.dtsi: add pci0/1/2 nodes

[Ben Dooks]

Add nodes for USB PCI bridge devices.

Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
---
Cc: devicetree@vger.kernel.org
Cc: linux-sh@vger.kernel.org
Cc: horms+renesas@verge.net.au
---
 arch/arm/boot/dts/r8a7790.dtsi | 30 ++++++++++++++++++++++++++++++
 1 file changed, 30 insertions(+)

diff --git a/arch/arm/boot/dts/r8a7790.dtsi b/arch/arm/boot/dts/r8a7790.dtsi
index 3cc834b..c5e9783 100644
--- a/arch/arm/boot/dts/r8a7790.dtsi
+++ b/arch/arm/boot/dts/r8a7790.dtsi
@@ -728,4 +728,34 @@
 				"rcan1", "rcan0", "qspi_mod", "i2c3", "i2c2", "i2c1", "i2c0";
 		};
 	};
+
+	pci0: pci@ee090000  {
+		compatible = "renesas,pci-r8a7790";
+		clocks = <&mstp7_clks R8A7790_CLK_EHCI>;
+		reg = <0x0 0xee090000 0x0 0xc00>,
+		      <0x0 0xee080000 0x0 0x1100>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 111 IRQ_TYPE_LEVEL_HIGH>;
+		status = "disabled";
+	};
+
+	pci1: pci@ee0b0000  {
+		compatible = "renesas,pci-r8a7790";
+		clocks = <&mstp7_clks R8A7790_CLK_EHCI>;
+		reg = <0x0 0xee0b0000 0x0 0xc00>,
+		      <0x0 0xee0a0000 0x0 0x1100>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 112 IRQ_TYPE_LEVEL_HIGH>;
+		status = "disabled";
+	};
+
+	pci2: pci@ee0d0000  {
+		compatible = "renesas,pci-r8a7790";
+		clocks = <&mstp7_clks R8A7790_CLK_EHCI>;
+		reg = <0x0 0xee0d0000 0x0 0xc00>,
+		      <0x0 0xee0c0000 0x0 0x1100>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 113 IRQ_TYPE_LEVEL_HIGH>;
+		status = "disabled";
+	};
 };
-- 
1.8.5.2

[PATCH 3/6] ARM: shmobile: lager.dts: add pci 0/1/2

[Ben Dooks]

Enable pci1 and pci2 nodes for USB controllers attached to the AHB<>PCI
bridge devices. Node pci0 is enabled for the moment as a device, but
could be switched to usb-gadget mode later.

Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
---
Cc: linux-sh@vger.kernel.org (open list:ARM/SHMOBILE ARM...)
Cc: devicetree@vger.kernel.org (open list:OPEN FIRMWARE AND...)
Cc: Magnus Damm <magnus.damm@gmail.com> (supporter:ARM/SHMOBILE ARM...)
Cc: Simon Horman <horms@verge.net.au> (supporter:ARM/SHMOBILE ARM...)
---
 arch/arm/boot/dts/r8a7790-lager.dts | 34 ++++++++++++++++++++++++++++++++++
 1 file changed, 34 insertions(+)

diff --git a/arch/arm/boot/dts/r8a7790-lager.dts b/arch/arm/boot/dts/r8a7790-lager.dts
index 57569cb..8dfcd25 100644
--- a/arch/arm/boot/dts/r8a7790-lager.dts
+++ b/arch/arm/boot/dts/r8a7790-lager.dts
@@ -80,6 +80,22 @@
 		renesas,groups = "mmc1_data8", "mmc1_ctrl";
 		renesas,function = "mmc1";
 	};
+
+	usb0_pins: usb0 {
+		renesas,groups = "usb0";
+		renesas,function = "usb";
+	};
+
+	usb1_pins: usb1 {
+		renesas,groups = "usb1";
+		renesas,function = "usb";
+	};
+
+	usb2_pins: usb2 {
+		renesas,groups = "usb2";
+		renesas,function = "usb";
+	};
+
 };
 
 &mmcif1 {
@@ -91,3 +107,21 @@
 	non-removable;
 	status = "okay";
 };
+
+&pci0 {
+	status = "okay";
+	pinctrl-0 = <&usb0_pins>;
+	pinctrl-names = "default";
+};
+
+&pci1 {
+	status = "okay";
+	pinctrl-0 = <&usb1_pins>;
+	pinctrl-names = "default";
+};
+
+&pci2 {
+	status = "okay";
+	pinctrl-0 = <&usb2_pins>;
+	pinctrl-names = "default";
+};
-- 
1.8.5.2

[PATCH 4/6] phy-rcar-usb-gen2: add device tree support

[Ben Dooks]

Add support for the phy-rcar-gen2-usb driver to be probed from device tree.

Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
---
Cc: linux-usb@vger.kernel.org (open list:USB PHY LAYER)
Cc: linux-sh@vger.kernel.org (open list:ARM/SHMOBILE ARM...)
Cc: Magnus Damm <magnus.damm@gmail.com> (supporter:ARM/SHMOBILE ARM...)
Cc: Simon Horman <horms@verge.net.au> (supporter:ARM/SHMOBILE ARM...)
Cc: devicetree@vger.kernel.org (open list:OPEN FIRMWARE AND...)
---
 drivers/usb/phy/phy-rcar-gen2-usb.c | 35 ++++++++++++++++++++++++++++++-----
 1 file changed, 30 insertions(+), 5 deletions(-)

diff --git a/drivers/usb/phy/phy-rcar-gen2-usb.c b/drivers/usb/phy/phy-rcar-gen2-usb.c
index db3ab34..906b74b 100644
--- a/drivers/usb/phy/phy-rcar-gen2-usb.c
+++ b/drivers/usb/phy/phy-rcar-gen2-usb.c
@@ -15,6 +15,7 @@
 #include <linux/module.h>
 #include <linux/platform_data/usb-rcar-gen2-phy.h>
 #include <linux/platform_device.h>
+#include <linux/of_device.h>
 #include <linux/spinlock.h>
 #include <linux/usb/otg.h>
 
@@ -167,8 +168,15 @@ out:
 	spin_unlock_irqrestore(&priv->lock, flags);
 }
 
+static struct of_device_id rcar_gen2_usb_phy_ofmatch[] = {
+	{ .compatible = "renesas,usb-phy-r8a7790", },
+	{ .compatible = "renesas,rcar-gen2-usb-phy", },
+	{ },
+};
+
 static int rcar_gen2_usb_phy_probe(struct platform_device *pdev)
 {
+	const struct of_device_id *of_id;
 	struct device *dev = &pdev->dev;
 	struct rcar_gen2_phy_platform_data *pdata;
 	struct rcar_gen2_usb_phy_priv *priv;
@@ -177,8 +185,9 @@ static int rcar_gen2_usb_phy_probe(struct platform_device *pdev)
 	struct clk *clk;
 	int retval;
 
+	of_id = of_match_device(rcar_gen2_usb_phy_ofmatch, &pdev->dev);
 	pdata = dev_get_platdata(&pdev->dev);
-	if (!pdata) {
+	if (!pdata && !of_id) {
 		dev_err(dev, "No platform data\n");
 		return -EINVAL;
 	}
@@ -203,16 +212,31 @@ static int rcar_gen2_usb_phy_probe(struct platform_device *pdev)
 	spin_lock_init(&priv->lock);
 	priv->clk = clk;
 	priv->base = base;
-	priv->ugctrl2 = pdata->chan0_pci ?
-			USBHS_UGCTRL2_USB0_PCI : USBHS_UGCTRL2_USB0_HS;
-	priv->ugctrl2 |= pdata->chan2_pci ?
-			USBHS_UGCTRL2_USB2_PCI : USBHS_UGCTRL2_USB2_SS;
 	priv->phy.dev = dev;
 	priv->phy.label = dev_name(dev);
 	priv->phy.init = rcar_gen2_usb_phy_init;
 	priv->phy.shutdown = rcar_gen2_usb_phy_shutdown;
 	priv->phy.set_suspend = rcar_gen2_usb_phy_set_suspend;
 
+	if (of_id) {
+		int len = 0;
+
+		if (of_get_property(dev->of_node, "renesas,usb0-hs", &len))
+			priv->ugctrl2 = USBHS_UGCTRL2_USB0_HS;
+		else
+			priv->ugctrl2 = USBHS_UGCTRL2_USB0_PCI;
+
+		if (of_get_property(dev->of_node, "renesas,usb2-ss", &len))
+			priv->ugctrl2 |= USBHS_UGCTRL2_USB2_SS;
+		else
+			priv->ugctrl2 |= USBHS_UGCTRL2_USB2_PCI;
+	} else {
+		priv->ugctrl2 = pdata->chan0_pci ?
+			USBHS_UGCTRL2_USB0_PCI : USBHS_UGCTRL2_USB0_HS;
+		priv->ugctrl2 |= pdata->chan2_pci ?
+			USBHS_UGCTRL2_USB2_PCI : USBHS_UGCTRL2_USB2_SS;
+	}
+
 	retval = usb_add_phy(&priv->phy, USB_PHY_TYPE_USB2);
 	if (retval < 0) {
 		dev_err(dev, "Failed to add USB phy\n");
@@ -236,6 +260,7 @@ static int rcar_gen2_usb_phy_remove(struct platform_device *pdev)
 static struct platform_driver rcar_gen2_usb_phy_driver = {
 	.driver = {
 		.name = "usb_phy_rcar_gen2",
+		.of_match_table = rcar_gen2_usb_phy_ofmatch,
 	},
 	.probe = rcar_gen2_usb_phy_probe,
 	.remove = rcar_gen2_usb_phy_remove,
-- 
1.8.5.2

Re: [PATCH 4/6] phy-rcar-usb-gen2: add device tree support

[Ben Dooks]

On 18/01/14 19:19, Sergei Shtylyov wrote:
> Hello.
>
> On 18-01-2014 19:03, Ben Dooks wrote:
>
>> Add support for the phy-rcar-gen2-usb driver to be probed from device
>> tree.
>
>> Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
>> Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
>> ---
>> Cc: linux-usb@vger.kernel.org (open list:USB PHY LAYER)
>> Cc: linux-sh@vger.kernel.org (open list:ARM/SHMOBILE ARM...)
>> Cc: Magnus Damm <magnus.damm@gmail.com> (supporter:ARM/SHMOBILE ARM...)
>> Cc: Simon Horman <horms@verge.net.au> (supporter:ARM/SHMOBILE ARM...)
>> Cc: devicetree@vger.kernel.org (open list:OPEN FIRMWARE AND...)
>> ---
>>   drivers/usb/phy/phy-rcar-gen2-usb.c | 35
>> ++++++++++++++++++++++++++++++-----
>>   1 file changed, 30 insertions(+), 5 deletions(-)
>
>> diff --git a/drivers/usb/phy/phy-rcar-gen2-usb.c
>> b/drivers/usb/phy/phy-rcar-gen2-usb.c
>> index db3ab34..906b74b 100644
>> --- a/drivers/usb/phy/phy-rcar-gen2-usb.c
>> +++ b/drivers/usb/phy/phy-rcar-gen2-usb.c
> [...]
>> @@ -177,8 +185,9 @@ static int rcar_gen2_usb_phy_probe(struct
>> platform_device *pdev)
>>       struct clk *clk;
>>       int retval;
>>
>> +    of_id = of_match_device(rcar_gen2_usb_phy_ofmatch, &pdev->dev);
>
>     I don't think another match is needed.
>
>>       pdata = dev_get_platdata(&pdev->dev);
>> -    if (!pdata) {
>> +    if (!pdata && !of_id) {
>>           dev_err(dev, "No platform data\n");
>>           return -EINVAL;
>>       }
>> @@ -203,16 +212,31 @@ static int rcar_gen2_usb_phy_probe(struct
>> platform_device *pdev)
> [...]
>> +    if (of_id) {
>
>     Isn't checking dev->of_node enough?

of_node does not contain the id of the entry matched at start time/

>> +        int len = 0;
>> +
>> +        if (of_get_property(dev->of_node, "renesas,usb0-hs", &len))
>> +            priv->ugctrl2 = USBHS_UGCTRL2_USB0_HS;
>> +        else
>> +            priv->ugctrl2 = USBHS_UGCTRL2_USB0_PCI;
>> +
>> +        if (of_get_property(dev->of_node, "renesas,usb2-ss", &len))
>> +            priv->ugctrl2 |= USBHS_UGCTRL2_USB2_SS;
>
>     Where is the bindings file you document these properties in?

Should have been in another patch in the series.


-- 
Ben Dooks				http://www.codethink.co.uk/
Senior Engineer				Codethink - Providing Genius

Re: [PATCH 4/6] phy-rcar-usb-gen2: add device tree support

[Sergei Shtylyov]

Hello.

On 20-01-2014 14:49, Ben Dooks wrote:

>>> Add support for the phy-rcar-gen2-usb driver to be probed from device
>>> tree.

>>> Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
>>> Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
>>> ---
>>> Cc: linux-usb@vger.kernel.org (open list:USB PHY LAYER)
>>> Cc: linux-sh@vger.kernel.org (open list:ARM/SHMOBILE ARM...)
>>> Cc: Magnus Damm <magnus.damm@gmail.com> (supporter:ARM/SHMOBILE ARM...)
>>> Cc: Simon Horman <horms@verge.net.au> (supporter:ARM/SHMOBILE ARM...)
>>> Cc: devicetree@vger.kernel.org (open list:OPEN FIRMWARE AND...)
>>> ---
>>>   drivers/usb/phy/phy-rcar-gen2-usb.c | 35
>>> ++++++++++++++++++++++++++++++-----
>>>   1 file changed, 30 insertions(+), 5 deletions(-)

>>> diff --git a/drivers/usb/phy/phy-rcar-gen2-usb.c
>>> b/drivers/usb/phy/phy-rcar-gen2-usb.c
>>> index db3ab34..906b74b 100644
>>> --- a/drivers/usb/phy/phy-rcar-gen2-usb.c
>>> +++ b/drivers/usb/phy/phy-rcar-gen2-usb.c
>> [...]
>>> @@ -177,8 +185,9 @@ static int rcar_gen2_usb_phy_probe(struct
>>> platform_device *pdev)
>>>       struct clk *clk;
>>>       int retval;
>>>
>>> +    of_id = of_match_device(rcar_gen2_usb_phy_ofmatch, &pdev->dev);

>>     I don't think another match is needed.

>>>       pdata = dev_get_platdata(&pdev->dev);
>>> -    if (!pdata) {
>>> +    if (!pdata && !of_id) {
>>>           dev_err(dev, "No platform data\n");
>>>           return -EINVAL;
>>>       }
>>> @@ -203,16 +212,31 @@ static int rcar_gen2_usb_phy_probe(struct
>>> platform_device *pdev)
>> [...]
>>> +    if (of_id) {

>>     Isn't checking dev->of_node enough?

> of_node does not contain the id of the entry matched at start time/

    I don't see where are you necessarily using that entry.

>>> +        int len = 0;
>>> +
>>> +        if (of_get_property(dev->of_node, "renesas,usb0-hs", &len))
>>> +            priv->ugctrl2 = USBHS_UGCTRL2_USB0_HS;
>>> +        else
>>> +            priv->ugctrl2 = USBHS_UGCTRL2_USB0_PCI;
>>> +
>>> +        if (of_get_property(dev->of_node, "renesas,usb2-ss", &len))
>>> +            priv->ugctrl2 |= USBHS_UGCTRL2_USB2_SS;

>>     Where is the bindings file you document these properties in?

> Should have been in another patch in the series.

    Hm, I think I saw all 6 patches of the series but no bindings.
Bindings files are typically appended to the patch that adds DT support to a 
driver...

WBR, Sergei

Re: [PATCH 4/6] phy-rcar-usb-gen2: add device tree support

[Sergei Shtylyov]

Hello.

On 20-01-2014 14:49, Ben Dooks wrote:

>>> Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
>>> Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
>>> ---
>>> Cc: linux-usb@vger.kernel.org (open list:USB PHY LAYER)
>>> Cc: linux-sh@vger.kernel.org (open list:ARM/SHMOBILE ARM...)
>>> Cc: Magnus Damm <magnus.damm@gmail.com> (supporter:ARM/SHMOBILE ARM...)
>>> Cc: Simon Horman <horms@verge.net.au> (supporter:ARM/SHMOBILE ARM...)
>>> Cc: devicetree@vger.kernel.org (open list:OPEN FIRMWARE AND...)
>>> ---
>>>   drivers/usb/phy/phy-rcar-gen2-usb.c | 35
>>> ++++++++++++++++++++++++++++++-----
>>>   1 file changed, 30 insertions(+), 5 deletions(-)

>>> diff --git a/drivers/usb/phy/phy-rcar-gen2-usb.c
>>> b/drivers/usb/phy/phy-rcar-gen2-usb.c
>>> index db3ab34..906b74b 100644
>>> --- a/drivers/usb/phy/phy-rcar-gen2-usb.c
>>> +++ b/drivers/usb/phy/phy-rcar-gen2-usb.c
>> [...]
>>> @@ -203,16 +212,31 @@ static int rcar_gen2_usb_phy_probe(struct
>>> platform_device *pdev)
>> [...]
>>> +    if (of_id) {
[...]
>>> +        int len = 0;
>>> +
>>> +        if (of_get_property(dev->of_node, "renesas,usb0-hs", &len))
>>> +            priv->ugctrl2 = USBHS_UGCTRL2_USB0_HS;
>>> +        else
>>> +            priv->ugctrl2 = USBHS_UGCTRL2_USB0_PCI;
>>> +
>>> +        if (of_get_property(dev->of_node, "renesas,usb2-ss", &len))
>>> +            priv->ugctrl2 |= USBHS_UGCTRL2_USB2_SS;

>>     Where is the bindings file you document these properties in?

> Should have been in another patch in the series.

    I didn't see it.

WBR, Sergei

Re: [PATCH 4/6] phy-rcar-usb-gen2: add device tree support

[Ben Dooks]

On 27/02/14 15:54, Sergei Shtylyov wrote:
> Hello.
>
> On 20-01-2014 14:49, Ben Dooks wrote:
>
>>>> Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
>>>> Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
>>>> ---
>>>> Cc: linux-usb@vger.kernel.org (open list:USB PHY LAYER)
>>>> Cc: linux-sh@vger.kernel.org (open list:ARM/SHMOBILE ARM...)
>>>> Cc: Magnus Damm <magnus.damm@gmail.com> (supporter:ARM/SHMOBILE ARM...)
>>>> Cc: Simon Horman <horms@verge.net.au> (supporter:ARM/SHMOBILE ARM...)
>>>> Cc: devicetree@vger.kernel.org (open list:OPEN FIRMWARE AND...)
>>>> ---
>>>>   drivers/usb/phy/phy-rcar-gen2-usb.c | 35
>>>> ++++++++++++++++++++++++++++++-----
>>>>   1 file changed, 30 insertions(+), 5 deletions(-)
>
>>>> diff --git a/drivers/usb/phy/phy-rcar-gen2-usb.c
>>>> b/drivers/usb/phy/phy-rcar-gen2-usb.c
>>>> index db3ab34..906b74b 100644
>>>> --- a/drivers/usb/phy/phy-rcar-gen2-usb.c
>>>> +++ b/drivers/usb/phy/phy-rcar-gen2-usb.c
>>> [...]
>>>> @@ -203,16 +212,31 @@ static int rcar_gen2_usb_phy_probe(struct
>>>> platform_device *pdev)
>>> [...]
>>>> +    if (of_id) {
> [...]
>>>> +        int len = 0;
>>>> +
>>>> +        if (of_get_property(dev->of_node, "renesas,usb0-hs", &len))
>>>> +            priv->ugctrl2 = USBHS_UGCTRL2_USB0_HS;
>>>> +        else
>>>> +            priv->ugctrl2 = USBHS_UGCTRL2_USB0_PCI;
>>>> +
>>>> +        if (of_get_property(dev->of_node, "renesas,usb2-ss", &len))
>>>> +            priv->ugctrl2 |= USBHS_UGCTRL2_USB2_SS;
>
>>>     Where is the bindings file you document these properties in?
>
>> Should have been in another patch in the series.
>
>     I didn't see it.

I thought it went out, I will need to go check.

-- 
Ben Dooks				http://www.codethink.co.uk/
Senior Engineer				Codethink - Providing Genius

Re: [PATCH 4/6] phy-rcar-usb-gen2: add device tree support

[Sergei Shtylyov]

Hello.

On 02/27/2014 07:03 PM, Ben Dooks wrote:

>>>>> Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
>>>>> Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
>>>>> ---
>>>>> Cc: linux-usb@vger.kernel.org (open list:USB PHY LAYER)
>>>>> Cc: linux-sh@vger.kernel.org (open list:ARM/SHMOBILE ARM...)
>>>>> Cc: Magnus Damm <magnus.damm@gmail.com> (supporter:ARM/SHMOBILE ARM...)
>>>>> Cc: Simon Horman <horms@verge.net.au> (supporter:ARM/SHMOBILE ARM...)
>>>>> Cc: devicetree@vger.kernel.org (open list:OPEN FIRMWARE AND...)
>>>>> ---
>>>>>   drivers/usb/phy/phy-rcar-gen2-usb.c | 35
>>>>> ++++++++++++++++++++++++++++++-----
>>>>>   1 file changed, 30 insertions(+), 5 deletions(-)

>>>>> diff --git a/drivers/usb/phy/phy-rcar-gen2-usb.c
>>>>> b/drivers/usb/phy/phy-rcar-gen2-usb.c
>>>>> index db3ab34..906b74b 100644
>>>>> --- a/drivers/usb/phy/phy-rcar-gen2-usb.c
>>>>> +++ b/drivers/usb/phy/phy-rcar-gen2-usb.c
>>>> [...]
>>>>> @@ -203,16 +212,31 @@ static int rcar_gen2_usb_phy_probe(struct
>>>>> platform_device *pdev)
>>>> [...]
>>>>> +    if (of_id) {
>> [...]
>>>>> +        int len = 0;
>>>>> +
>>>>> +        if (of_get_property(dev->of_node, "renesas,usb0-hs", &len))
>>>>> +            priv->ugctrl2 = USBHS_UGCTRL2_USB0_HS;
>>>>> +        else
>>>>> +            priv->ugctrl2 = USBHS_UGCTRL2_USB0_PCI;
>>>>> +
>>>>> +        if (of_get_property(dev->of_node, "renesas,usb2-ss", &len))
>>>>> +            priv->ugctrl2 |= USBHS_UGCTRL2_USB2_SS;

>>>>     Where is the bindings file you document these properties in?

>>> Should have been in another patch in the series.

>>     I didn't see it.

> I thought it went out, I will need to go check.

    It turned out that I'd already replied to that email that I had seen all 6 
patches but not the binding patch, so most probably it didn't went out that 
time. I've seen the latter patch (just not posted to linux-usb), so no problem 
here.

WBR, Sergei

Re: [PATCH 4/6] phy-rcar-usb-gen2: add device tree support

[Ben Dooks]

On 20/01/14 12:18, Sergei Shtylyov wrote:
> Hello.
>
> On 18-01-2014 19:03, Ben Dooks wrote:
>
>> Add support for the phy-rcar-gen2-usb driver to be probed from device
>> tree.
>
>> Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
>> Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
>> ---
>> Cc: linux-usb@vger.kernel.org (open list:USB PHY LAYER)
>> Cc: linux-sh@vger.kernel.org (open list:ARM/SHMOBILE ARM...)
>> Cc: Magnus Damm <magnus.damm@gmail.com> (supporter:ARM/SHMOBILE ARM...)
>> Cc: Simon Horman <horms@verge.net.au> (supporter:ARM/SHMOBILE ARM...)
>> Cc: devicetree@vger.kernel.org (open list:OPEN FIRMWARE AND...)
>> ---
>>   drivers/usb/phy/phy-rcar-gen2-usb.c | 35
>> ++++++++++++++++++++++++++++++-----
>>   1 file changed, 30 insertions(+), 5 deletions(-)
>
>> diff --git a/drivers/usb/phy/phy-rcar-gen2-usb.c
>> b/drivers/usb/phy/phy-rcar-gen2-usb.c
>> index db3ab34..906b74b 100644
>> --- a/drivers/usb/phy/phy-rcar-gen2-usb.c
>> +++ b/drivers/usb/phy/phy-rcar-gen2-usb.c
> [...]
>> @@ -203,16 +212,31 @@ static int rcar_gen2_usb_phy_probe(struct
>> platform_device *pdev)
> [...]
>> +    if (of_id) {
>> +        int len = 0;
>> +
>> +        if (of_get_property(dev->of_node, "renesas,usb0-hs", &len))
>> +            priv->ugctrl2 = USBHS_UGCTRL2_USB0_HS;
>> +        else
>> +            priv->ugctrl2 = USBHS_UGCTRL2_USB0_PCI;
>> +
>> +        if (of_get_property(dev->of_node, "renesas,usb2-ss", &len))
>
>     You can use of_property_read_bool() in both cases as both these
> props are boolean I guess. It's more handy.

Thanks, missed that one, will sort that out.


-- 
Ben Dooks				http://www.codethink.co.uk/
Senior Engineer				Codethink - Providing Genius

[PATCH 5/6] ARM: shmobile: r8a7790.dtsi: add usbphy node

[Ben Dooks]

Add node for USB PHY driver to the base R8A7790 device tree include file.
It is up to the board file to enable and configure it as necessary.

Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
---
Cc: devicetree@vger.kernel.org (open list:OPEN FIRMWARE AND...)
Cc: Magnus Damm <magnus.damm@gmail.com> (supporter:ARM/SHMOBILE ARM...)
Cc: Simon Horman <horms@verge.net.au> (supporter:ARM/SHMOBILE ARM...)
Cc: linux-sh@vger.kernel.org (open list:ARM/SHMOBILE ARM...)
---
 arch/arm/boot/dts/r8a7790.dtsi | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/arch/arm/boot/dts/r8a7790.dtsi b/arch/arm/boot/dts/r8a7790.dtsi
index c5e9783..ea180a5 100644
--- a/arch/arm/boot/dts/r8a7790.dtsi
+++ b/arch/arm/boot/dts/r8a7790.dtsi
@@ -758,4 +758,12 @@
 		interrupts = <0 113 IRQ_TYPE_LEVEL_HIGH>;
 		status = "disabled";
 	};
+
+	usbphy: usbphy@e6590100 {
+		compatible = "renesas,usb-phy-r8a7790";
+		clocks = <&mstp7_clks R8A7790_CLK_HSUSB>;
+		clock-names = "usbhs";
+		reg = < 0x0 0xe6590100 0x0 0x100>;
+		status = "disabled";
+	};
 };
-- 
1.8.5.2

[PATCH 6/6] ARM: shmobile: lager.dtb: add usbphy reference

[Ben Dooks]

Enable the usbphy node so that the phy driver is available.

Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
---
Cc: linux-sh@vger.kernel.org (open list:ARM/SHMOBILE ARM...)
Cc: devicetree@vger.kernel.org (open list:OPEN FIRMWARE AND...)
Cc: Magnus Damm <magnus.damm@gmail.com> (supporter:ARM/SHMOBILE ARM...)
Cc: Simon Horman <horms@verge.net.au> (supporter:ARM/SHMOBILE ARM...)
---
 arch/arm/boot/dts/r8a7790-lager.dts | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm/boot/dts/r8a7790-lager.dts b/arch/arm/boot/dts/r8a7790-lager.dts
index 8dfcd25..83bf18d 100644
--- a/arch/arm/boot/dts/r8a7790-lager.dts
+++ b/arch/arm/boot/dts/r8a7790-lager.dts
@@ -125,3 +125,7 @@
 	pinctrl-0 = <&usb2_pins>;
 	pinctrl-names = "default";
 };
+
+&usbphy {
+	status = "okay";
+};
-- 
1.8.5.2