[PATCH v2 0/6] IIO pulse capture support for TI ECAP

[PATCH v2 0/6] IIO pulse capture support for TI ECAP

[Matt Porter]

Changes since v1:
	- Rebased to 3.14-rc1
	- Renamed in_pulse_polarity to pulse_polarity
	- Added ABI entries for pulse devices and TI ECAP

This series adds support for PWM capture devices within IIO and
adds a TI ECAP IIO driver.

PWM capture devices are supported using a new IIO "pulse" channel type.

The IIO ECAP driver implements interrupt driven triggered buffer capture
only as raw sample reads are not applicable to this hardware.
Initially, the driver supports a single pulse width measurement with
configurable polarity. The ECAP hardware can support measurement of a
complete period and duty cycle but this is not yet implemented.

Matt Porter (6):
  iio: add support for pulse width capture devices
  iio: pulse: add TI ECAP driver
  iio: enable selection and build of pulse drivers
  iio: Add ABI docs for pulse capture devices
  pwm: enable TI PWMSS if the IIO tiecap driver is selected
  ARM: dts: AM33XX: Add ecap interrupt properties

 Documentation/ABI/testing/sysfs-bus-iio            |  18 +
 .../ABI/testing/sysfs-bus-iio-pulse-tiecap         |   9 +
 arch/arm/boot/dts/am33xx.dtsi                      |   6 +
 drivers/iio/Kconfig                                |   1 +
 drivers/iio/Makefile                               |   1 +
 drivers/iio/industrialio-core.c                    |   1 +
 drivers/iio/pulse/Kconfig                          |  20 +
 drivers/iio/pulse/Makefile                         |   6 +
 drivers/iio/pulse/tiecap.c                         | 493 +++++++++++++++++++++
 drivers/pwm/Kconfig                                |   2 +-
 include/linux/iio/types.h                          |   1 +
 11 files changed, 557 insertions(+), 1 deletion(-)
 create mode 100644 Documentation/ABI/testing/sysfs-bus-iio-pulse-tiecap
 create mode 100644 drivers/iio/pulse/Kconfig
 create mode 100644 drivers/iio/pulse/Makefile
 create mode 100644 drivers/iio/pulse/tiecap.c

-- 
1.8.4

[PATCH v2 1/6] iio: add support for pulse width capture devices

[Matt Porter]

Add a channel type to support pulse width capture devices.
These devices capture the timing of a PWM signal based on a
configurable trigger

Signed-off-by: Matt Porter <mporter@linaro.org>
---
 drivers/iio/industrialio-core.c | 1 +
 include/linux/iio/types.h       | 1 +
 2 files changed, 2 insertions(+)

diff --git a/drivers/iio/industrialio-core.c b/drivers/iio/industrialio-core.c
index acc911a..6ea0cf8 100644
--- a/drivers/iio/industrialio-core.c
+++ b/drivers/iio/industrialio-core.c
@@ -70,6 +70,7 @@ static const char * const iio_chan_type_name_spec[] = {
 	[IIO_CCT] = "cct",
 	[IIO_PRESSURE] = "pressure",
 	[IIO_HUMIDITYRELATIVE] = "humidityrelative",
+	[IIO_PULSE] = "pulse",
 };
 
 static const char * const iio_modifier_names[] = {
diff --git a/include/linux/iio/types.h b/include/linux/iio/types.h
index 084d882..4fa8840 100644
--- a/include/linux/iio/types.h
+++ b/include/linux/iio/types.h
@@ -30,6 +30,7 @@ enum iio_chan_type {
 	IIO_CCT,
 	IIO_PRESSURE,
 	IIO_HUMIDITYRELATIVE,
+	IIO_PULSE,
 };
 
 enum iio_modifier {
-- 
1.8.4

[PATCH v2 2/6] iio: pulse: add TI ECAP driver

[Matt Porter]

Adds support for capturing PWM signals using the TI ECAP peripheral.
This driver supports triggered buffer capture of pulses on multiple
ECAP instances. In addition, the driver supports configurable polarity
of the signal to be captured.

Signed-off-by: Matt Porter <mporter-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
---
 drivers/iio/pulse/Kconfig  |  20 ++
 drivers/iio/pulse/Makefile |   6 +
 drivers/iio/pulse/tiecap.c | 493 +++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 519 insertions(+)
 create mode 100644 drivers/iio/pulse/Kconfig
 create mode 100644 drivers/iio/pulse/Makefile
 create mode 100644 drivers/iio/pulse/tiecap.c

diff --git a/drivers/iio/pulse/Kconfig b/drivers/iio/pulse/Kconfig
new file mode 100644
index 0000000..9864d4b
--- /dev/null
+++ b/drivers/iio/pulse/Kconfig
@@ -0,0 +1,20 @@
+#
+# Pulse Capture Devices
+#
+# When adding new entries keep the list in alphabetical order
+
+menu "Pulse Capture Devices"
+
+config IIO_TIECAP
+	tristate "TI ECAP Pulse Capture"
+	depends on SOC_AM33XX
+	select IIO_BUFFER
+	select IIO_TRIGGERED_BUFFER
+	help
+	 If you say yes here you get support for the TI ECAP peripheral
+	 in pulse capture mode.
+
+	 This driver can also be built as a module.  If so, the module
+	 will be called tiecap
+
+endmenu
diff --git a/drivers/iio/pulse/Makefile b/drivers/iio/pulse/Makefile
new file mode 100644
index 0000000..94d4b00
--- /dev/null
+++ b/drivers/iio/pulse/Makefile
@@ -0,0 +1,6 @@
+#
+# Makefile for IIO PWM Capture Devices
+#
+
+# When adding new entries keep the list in alphabetical order
+obj-$(CONFIG_IIO_TIECAP)	+= tiecap.o
diff --git a/drivers/iio/pulse/tiecap.c b/drivers/iio/pulse/tiecap.c
new file mode 100644
index 0000000..3d21080
--- /dev/null
+++ b/drivers/iio/pulse/tiecap.c
@@ -0,0 +1,493 @@
+/*
+ * ECAP IIO pulse capture driver
+ *
+ * Copyright (C) 2014 Linaro Limited
+ * Author: Matt Porter <mporter-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/iio/buffer.h>
+#include <linux/iio/iio.h>
+#include <linux/iio/sysfs.h>
+#include <linux/iio/trigger.h>
+#include <linux/iio/trigger_consumer.h>
+#include <linux/iio/triggered_buffer.h>
+#include <linux/io.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+
+#include "../../pwm/pwm-tipwmss.h"
+
+/* ECAP regs and bits */
+#define CAP1			0x08
+#define CAP2			0x0c
+#define ECCTL1			0x28
+#define ECCTL1_RUN_FREE		BIT(15)
+#define ECCTL1_CAPLDEN		BIT(8)
+#define ECCTL1_CAP2POL		BIT(2)
+#define ECCTL1_CTRRST1		BIT(1)
+#define ECCTL1_CAP1POL		BIT(0)
+#define ECCTL2			0x2a
+#define ECCTL2_SYNCO_SEL_DIS	BIT(7)
+#define ECCTL2_TSCTR_FREERUN	BIT(4)
+#define ECCTL2_REARM		BIT(3)
+#define ECCTL2_STOP_WRAP_2	BIT(1)
+#define ECEINT			0x2c
+#define ECFLG			0x2e
+#define ECCLR			0x30
+#define ECINT_CTRCMP		BIT(7)
+#define ECINT_CTRPRD		BIT(6)
+#define ECINT_CTROVF		BIT(5)
+#define ECINT_CEVT4		BIT(4)
+#define ECINT_CEVT3		BIT(3)
+#define ECINT_CEVT2		BIT(2)
+#define ECINT_CEVT1		BIT(1)
+#define ECINT_ALL		(ECINT_CTRCMP |	\
+				ECINT_CTRPRD |	\
+				ECINT_CTROVF |	\
+				ECINT_CEVT4 |	\
+				ECINT_CEVT3 |	\
+				ECINT_CEVT2 |	\
+				ECINT_CEVT1)
+
+/* ECAP driver flags */
+#define ECAP_POLARITY_HIGH	BIT(1)
+#define ECAP_ENABLED		BIT(0)
+
+struct ecap_context {
+	u32	cap1;
+	u32	cap2;
+	u16	ecctl1;
+	u16	ecctl2;
+	u16	eceint;
+};
+
+struct ecap_state {
+	unsigned long		flags;
+	unsigned int		clk_rate;
+	void __iomem		*regs;
+	u32			*buf;
+	struct ecap_context	ctx;
+};
+
+#define dev_to_ecap_state(d)	iio_priv(dev_to_iio_dev(d))
+
+static const struct iio_chan_spec ecap_channels[] = {
+	{
+		.type		= IIO_PULSE,
+		.channel	= 0,
+		.info_mask_separate =
+			BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_SCALE),
+		.scan_index	= 0,
+		.scan_type = {
+			.sign		= 'u',
+			.realbits	= 32,
+			.storagebits	= 32,
+			.endianness	= IIO_LE,
+		},
+		.modified = 0,
+	},
+	IIO_CHAN_SOFT_TIMESTAMP(1)
+};
+
+static ssize_t ecap_attr_show(struct device *dev,
+			      struct device_attribute *attr, char *buf)
+{
+	struct ecap_state *state = dev_to_ecap_state(dev);
+
+	return sprintf(buf, "%d\n",
+		       test_bit(ECAP_POLARITY_HIGH, &state->flags));
+}
+
+static ssize_t ecap_attr_store(struct device *dev,
+			       struct device_attribute *attr,
+			       const char *buf,
+			       size_t len)
+{
+	int ret;
+	bool val;
+	struct ecap_state *state = dev_to_ecap_state(dev);
+
+	if (test_bit(ECAP_ENABLED, &state->flags))
+		return -EINVAL;
+
+	ret = strtobool(buf, &val);
+	if (ret)
+		return ret;
+
+	if (val)
+		set_bit(ECAP_POLARITY_HIGH, &state->flags);
+	else
+		clear_bit(ECAP_POLARITY_HIGH, &state->flags);
+
+	return len;
+}
+
+static IIO_DEVICE_ATTR(pulse_polarity, S_IRUGO | S_IWUSR,
+	ecap_attr_show, ecap_attr_store, 0);
+
+static struct attribute *ecap_attributes[] = {
+	&iio_dev_attr_pulse_polarity.dev_attr.attr,
+	NULL,
+};
+
+static struct attribute_group ecap_attribute_group = {
+	.attrs = ecap_attributes,
+};
+
+static int ecap_read_raw(struct iio_dev *idev,
+			struct iio_chan_spec const *ch, int *val,
+			int *val2, long mask)
+{
+	struct ecap_state *state = iio_priv(idev);
+
+	switch (mask) {
+	case IIO_CHAN_INFO_RAW:
+		/*
+		 * Always return 0 as a pulse width sample
+		 * is only valid in a triggered condition
+		 */
+		*val = 0;
+		*val2 = 0;
+		return IIO_VAL_INT;
+	case IIO_CHAN_INFO_SCALE:
+		*val = 0;
+		*val2 = NSEC_PER_SEC / state->clk_rate;
+		return IIO_VAL_INT_PLUS_NANO;
+	default:
+		return -EINVAL;
+	}
+}
+
+static const struct iio_info ecap_info = {
+	.driver_module = THIS_MODULE,
+	.attrs = &ecap_attribute_group,
+	.read_raw = &ecap_read_raw,
+};
+
+static irqreturn_t ecap_trigger_handler(int irq, void *private)
+{
+	struct iio_poll_func *pf = private;
+	struct iio_dev *idev = pf->indio_dev;
+	struct ecap_state *state = iio_priv(idev);
+
+	/* Read pulse counter value */
+	*state->buf = readl(state->regs + CAP2);
+
+	iio_push_to_buffers_with_timestamp(idev, state->buf, iio_get_time_ns());
+
+	iio_trigger_notify_done(idev->trig);
+
+	return IRQ_HANDLED;
+};
+
+
+static const struct iio_trigger_ops iio_interrupt_trigger_ops = {
+	.owner = THIS_MODULE,
+};
+
+static irqreturn_t ecap_interrupt_handler(int irq, void *private)
+{
+	struct iio_dev *idev = private;
+	struct ecap_state *state = iio_priv(idev);
+	u16 ints;
+
+	iio_trigger_poll(idev->trig, 0);
+
+	/* Clear CAP2 interrupt */
+	ints = readw(state->regs + ECFLG);
+	if (ints & ECINT_CEVT2)
+		writew(ECINT_CEVT2, state->regs + ECCLR);
+	else
+		dev_warn(&idev->dev, "unhandled interrupt flagged: %04x\n",
+			 ints);
+
+	return IRQ_HANDLED;
+}
+
+static int ecap_buffer_predisable(struct iio_dev *idev)
+{
+	struct ecap_state *state = iio_priv(idev);
+	int ret = 0;
+	u16 ecctl2;
+
+	/* Stop capture */
+	clear_bit(ECAP_ENABLED, &state->flags);
+	ecctl2 = readw(state->regs + ECCTL2) & ~ECCTL2_TSCTR_FREERUN;
+	writew(ecctl2, state->regs + ECCTL2);
+
+	/* Disable and clear all interrupts */
+	writew(0, state->regs + ECEINT);
+	writew(ECINT_ALL, state->regs + ECCLR);
+
+	ret = iio_triggered_buffer_predisable(idev);
+
+	pm_runtime_put_sync(idev->dev.parent);
+
+	return ret;
+}
+
+static int ecap_buffer_postenable(struct iio_dev *idev)
+{
+	struct ecap_state *state = iio_priv(idev);
+	int ret = 0;
+	u16 ecctl1, ecctl2;
+
+	pm_runtime_get_sync(idev->dev.parent);
+
+	/* Configure pulse polarity */
+	ecctl1 = readw(state->regs + ECCTL1);
+	if (test_bit(ECAP_POLARITY_HIGH, &state->flags)) {
+		/* CAP1 rising, CAP2 falling */
+		ecctl1 |= ECCTL1_CAP2POL;
+		ecctl1 &= ~ECCTL1_CAP1POL;
+	} else {
+		/* CAP1 falling, CAP2 rising */
+		ecctl1 &= ~ECCTL1_CAP2POL;
+		ecctl1 |= ECCTL1_CAP1POL;
+	}
+	writew(ecctl1, state->regs + ECCTL1);
+
+	/* Enable CAP2 interrupt */
+	writew(ECINT_CEVT2, state->regs + ECEINT);
+
+	/* Enable capture */
+	ecctl2 = readw(state->regs + ECCTL2);
+	ecctl2 |= ECCTL2_TSCTR_FREERUN | ECCTL2_REARM;
+	writew(ecctl2, state->regs + ECCTL2);
+	set_bit(ECAP_ENABLED, &state->flags);
+
+	ret = iio_triggered_buffer_postenable(idev);
+
+	return ret;
+}
+
+static const struct iio_buffer_setup_ops ecap_buffer_setup_ops = {
+	.postenable = &ecap_buffer_postenable,
+	.predisable = &ecap_buffer_predisable,
+};
+
+static void ecap_init_hw(struct iio_dev *idev)
+{
+	struct ecap_state *state = iio_priv(idev);
+
+	clear_bit(ECAP_ENABLED, &state->flags);
+	set_bit(ECAP_POLARITY_HIGH, &state->flags);
+
+	writew(ECCTL1_RUN_FREE | ECCTL1_CAPLDEN |
+	       ECCTL1_CAP2POL | ECCTL1_CTRRST1,
+	       state->regs + ECCTL1);
+
+	writew(ECCTL2_SYNCO_SEL_DIS | ECCTL2_STOP_WRAP_2,
+	       state->regs + ECCTL2);
+}
+
+static const struct of_device_id ecap_of_ids[] = {
+	{ .compatible	= "ti,am33xx-ecap" },
+	{ /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, ecap_of_ids);
+
+static int ecap_probe(struct platform_device *pdev)
+{
+	int irq, ret;
+	struct iio_dev *idev;
+	struct ecap_state *state;
+	struct resource *r;
+	struct clk *clk;
+	struct iio_trigger *trig;
+	u16 status;
+
+	idev = devm_iio_device_alloc(&pdev->dev, sizeof(struct ecap_state));
+	if (!idev)
+		return -ENOMEM;
+
+	state = iio_priv(idev);
+
+	clk = devm_clk_get(&pdev->dev, "fck");
+	if (IS_ERR(clk)) {
+		dev_err(&pdev->dev, "failed to get clock\n");
+		return PTR_ERR(clk);
+	}
+
+	state->clk_rate = clk_get_rate(clk);
+	if (!state->clk_rate) {
+		dev_err(&pdev->dev, "failed to get clock rate\n");
+		return -EINVAL;
+	}
+
+	platform_set_drvdata(pdev, idev);
+
+	idev->dev.parent = &pdev->dev;
+	idev->name = dev_name(&pdev->dev);
+	idev->modes = INDIO_DIRECT_MODE;
+	idev->info = &ecap_info;
+	idev->channels = ecap_channels;
+	/* One h/w capture and one s/w timestamp channel per instance */
+	idev->num_channels = 2;
+
+	trig = devm_iio_trigger_alloc(&pdev->dev, "%s-dev%d",
+				      idev->name, idev->id);
+	if (!trig)
+		return -ENOMEM;
+	trig->dev.parent = idev->dev.parent;
+	iio_trigger_set_drvdata(trig, idev);
+	trig->ops = &iio_interrupt_trigger_ops;
+
+	ret = iio_trigger_register(trig);
+	if (ret) {
+		dev_err(&pdev->dev, "failed to register trigger\n");
+		return ret;
+	}
+
+	ret = iio_triggered_buffer_setup(idev, NULL,
+					 &ecap_trigger_handler,
+					 &ecap_buffer_setup_ops);
+	if (ret)
+		return ret;
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
+		dev_err(&pdev->dev, "no irq is specified\n");
+		return irq;
+	}
+	ret = devm_request_irq(&pdev->dev, irq,
+				&ecap_interrupt_handler,
+				0, dev_name(&pdev->dev), idev);
+	if (ret) {
+		dev_err(&pdev->dev, "unable to request irq\n");
+		goto uninit_buffer;
+	}
+
+	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	state->regs = devm_ioremap_resource(&pdev->dev, r);
+	if (IS_ERR(state->regs)) {
+		dev_err(&pdev->dev, "unable to remap registers\n");
+		ret = PTR_ERR(state->regs);
+		goto uninit_buffer;
+	};
+
+	ret = iio_device_register(idev);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "unable to register device\n");
+		goto uninit_buffer;
+	}
+
+	state->buf = devm_kzalloc(&idev->dev, idev->scan_bytes, GFP_KERNEL);
+	if (!state->buf) {
+		ret = -ENOMEM;
+		goto uninit_buffer;
+	}
+
+	pm_runtime_enable(&pdev->dev);
+	pm_runtime_get_sync(&pdev->dev);
+
+	status = pwmss_submodule_state_change(pdev->dev.parent,
+			PWMSS_ECAPCLK_EN);
+	if (!(status & PWMSS_ECAPCLK_EN_ACK)) {
+		dev_err(&pdev->dev, "failed to enable PWMSS config space clock\n");
+		ret = -EINVAL;
+		goto pwmss_clk_failure;
+	}
+
+	ecap_init_hw(idev);
+
+	pm_runtime_put_sync(&pdev->dev);
+
+	return 0;
+
+pwmss_clk_failure:
+	pm_runtime_put_sync(&pdev->dev);
+	pm_runtime_disable(&pdev->dev);
+	iio_device_unregister(idev);
+
+uninit_buffer:
+	iio_triggered_buffer_cleanup(idev);
+
+	return ret;
+}
+
+static int ecap_remove(struct platform_device *pdev)
+{
+	struct iio_dev *idev = platform_get_drvdata(pdev);
+
+	pm_runtime_get_sync(&pdev->dev);
+
+	pwmss_submodule_state_change(pdev->dev.parent, PWMSS_ECAPCLK_STOP_REQ);
+
+	pm_runtime_put_sync(&pdev->dev);
+	pm_runtime_disable(&pdev->dev);
+
+	iio_device_unregister(idev);
+
+	return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int ecap_suspend(struct device *dev)
+{
+	struct ecap_state *state = dev_to_ecap_state(dev);
+
+	pm_runtime_get_sync(dev);
+	state->ctx.cap1 = readl(state->regs + CAP1);
+	state->ctx.cap2 = readl(state->regs + CAP2);
+	state->ctx.eceint = readw(state->regs + ECEINT);
+	state->ctx.ecctl1 = readw(state->regs + ECCTL1);
+	state->ctx.ecctl2 = readw(state->regs + ECCTL2);
+	pm_runtime_put_sync(dev);
+
+	/* If capture was active, disable ECAP */
+	if (test_bit(ECAP_ENABLED, &state->flags))
+		pm_runtime_put_sync(dev);
+
+	return 0;
+}
+
+static int ecap_resume(struct device *dev)
+{
+	struct ecap_state *state = dev_to_ecap_state(dev);
+
+	/* If capture was active, enable ECAP */
+	if (test_bit(ECAP_ENABLED, &state->flags))
+		pm_runtime_get_sync(dev);
+
+	pm_runtime_get_sync(dev);
+	writel(state->ctx.cap1, state->regs + CAP1);
+	writel(state->ctx.cap2, state->regs + CAP2);
+	writew(state->ctx.eceint, state->regs + ECEINT);
+	writew(state->ctx.ecctl1, state->regs + ECCTL1);
+	writew(state->ctx.ecctl2, state->regs + ECCTL2);
+	pm_runtime_put_sync(dev);
+
+	return 0;
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(ecap_pm_ops, ecap_suspend, ecap_resume);
+
+static struct platform_driver ecap_iio_driver = {
+	.driver = {
+		.name		= "ecap",
+		.owner		= THIS_MODULE,
+		.of_match_table = of_match_ptr(ecap_of_ids),
+		.pm		= &ecap_pm_ops,
+	},
+	.probe = ecap_probe,
+	.remove = ecap_remove,
+};
+
+module_platform_driver(ecap_iio_driver);
+
+MODULE_DESCRIPTION("ECAP IIO pulse capture driver");
+MODULE_AUTHOR("Matt Porter <mporter-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>");
+MODULE_LICENSE("GPL");
-- 
1.8.4

[PATCH v2 5/6] pwm: enable TI PWMSS if the IIO tiecap driver is selected

[Matt Porter]

The IIO TI ECAP driver depends on the TI PWMSS management
driver in this subsystem. Enable PWMSS when the IIO TI ECAP
driver is selected.

Signed-off-by: Matt Porter <mporter-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
---
 drivers/pwm/Kconfig | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/pwm/Kconfig b/drivers/pwm/Kconfig
index 22f2f28..bd3cc65 100644
--- a/drivers/pwm/Kconfig
+++ b/drivers/pwm/Kconfig
@@ -219,7 +219,7 @@ config  PWM_TIEHRPWM
 
 config  PWM_TIPWMSS
 	bool
-	default y if SOC_AM33XX && (PWM_TIECAP || PWM_TIEHRPWM)
+	default y if SOC_AM33XX && (IIO_TIECAP || PWM_TIECAP || PWM_TIEHRPWM)
 	help
 	  PWM Subsystem driver support for AM33xx SOC.
 
-- 
1.8.4

[PATCH v2 3/6] iio: enable selection and build of pulse drivers

[Matt Porter]

Add the pulse driver subdirectory when configuring and building
IIO.

Signed-off-by: Matt Porter <mporter@linaro.org>
---
 drivers/iio/Kconfig  | 1 +
 drivers/iio/Makefile | 1 +
 2 files changed, 2 insertions(+)

diff --git a/drivers/iio/Kconfig b/drivers/iio/Kconfig
index 5dd0e12..286acc3 100644
--- a/drivers/iio/Kconfig
+++ b/drivers/iio/Kconfig
@@ -74,6 +74,7 @@ if IIO_TRIGGER
    source "drivers/iio/trigger/Kconfig"
 endif #IIO_TRIGGER
 source "drivers/iio/pressure/Kconfig"
+source "drivers/iio/pulse/Kconfig"
 source "drivers/iio/temperature/Kconfig"
 
 endif # IIO
diff --git a/drivers/iio/Makefile b/drivers/iio/Makefile
index 887d390..9a953c9 100644
--- a/drivers/iio/Makefile
+++ b/drivers/iio/Makefile
@@ -24,5 +24,6 @@ obj-y += light/
 obj-y += magnetometer/
 obj-y += orientation/
 obj-y += pressure/
+obj-y += pulse/
 obj-y += temperature/
 obj-y += trigger/
-- 
1.8.4

[PATCH v2 4/6] iio: Add ABI docs for pulse capture devices

[Matt Porter]

Add standard ABI entries for pulse capture devices. Also add
a separate ABI entry for the TI ECAP driver polarity option.

Signed-off-by: Matt Porter <mporter@linaro.org>
---
 Documentation/ABI/testing/sysfs-bus-iio              | 18 ++++++++++++++++++
 Documentation/ABI/testing/sysfs-bus-iio-pulse-tiecap |  9 +++++++++
 2 files changed, 27 insertions(+)
 create mode 100644 Documentation/ABI/testing/sysfs-bus-iio-pulse-tiecap

diff --git a/Documentation/ABI/testing/sysfs-bus-iio b/Documentation/ABI/testing/sysfs-bus-iio
index 6e02c50..918a201 100644
--- a/Documentation/ABI/testing/sysfs-bus-iio
+++ b/Documentation/ABI/testing/sysfs-bus-iio
@@ -210,6 +210,14 @@ Contact:	linux-iio@vger.kernel.org
 Description:
 		Scaled humidity measurement in milli percent.
 
+What:		/sys/bus/iio/devices/iio:deviceX/in_pulseY_raw
+What:		/sys/bus/iio/devices/iio:deviceX/in_pulse_raw
+KernelVersion:	3.15
+Contact:	linux-iio@vger.kernel.org
+Description:
+		Raw pulse measurement from channel Y. Units after
+		application of scale and offset are nanoseconds.
+
 What:		/sys/bus/iio/devices/iio:deviceX/in_accel_offset
 What:		/sys/bus/iio/devices/iio:deviceX/in_accel_x_offset
 What:		/sys/bus/iio/devices/iio:deviceX/in_accel_y_offset
@@ -220,6 +228,8 @@ What:		/sys/bus/iio/devices/iio:deviceX/in_tempY_offset
 What:		/sys/bus/iio/devices/iio:deviceX/in_temp_offset
 What:		/sys/bus/iio/devices/iio:deviceX/in_pressureY_offset
 What:		/sys/bus/iio/devices/iio:deviceX/in_pressure_offset
+What:		/sys/bus/iio/devices/iio:deviceX/in_pulseY_offset
+What:		/sys/bus/iio/devices/iio:deviceX/in_pulse_offset
 KernelVersion:	2.6.35
 Contact:	linux-iio@vger.kernel.org
 Description:
@@ -251,6 +261,8 @@ What:		/sys/bus/iio/devices/iio:deviceX/in_magn_y_scale
 What:		/sys/bus/iio/devices/iio:deviceX/in_magn_z_scale
 What:		/sys/bus/iio/devices/iio:deviceX/in_pressureY_scale
 What:		/sys/bus/iio/devices/iio:deviceX/in_pressure_scale
+What:		/sys/bus/iio/devices/iio:deviceX/in_pulseY_scale
+What:		/sys/bus/iio/devices/iio:deviceX/in_pulse_scale
 KernelVersion:	2.6.35
 Contact:	linux-iio@vger.kernel.org
 Description:
@@ -784,6 +796,8 @@ What:		/sys/.../iio:deviceX/scan_elements/in_incli_x_en
 What:		/sys/.../iio:deviceX/scan_elements/in_incli_y_en
 What:		/sys/.../iio:deviceX/scan_elements/in_pressureY_en
 What:		/sys/.../iio:deviceX/scan_elements/in_pressure_en
+What:		/sys/.../iio:deviceX/scan_elements/in_pulseY_en
+What:		/sys/.../iio:deviceX/scan_elements/in_pulse_en
 KernelVersion:	2.6.37
 Contact:	linux-iio@vger.kernel.org
 Description:
@@ -799,6 +813,8 @@ What:		/sys/.../iio:deviceX/scan_elements/in_voltageY_supply_type
 What:		/sys/.../iio:deviceX/scan_elements/in_timestamp_type
 What:		/sys/.../iio:deviceX/scan_elements/in_pressureY_type
 What:		/sys/.../iio:deviceX/scan_elements/in_pressure_type
+What:		/sys/.../iio:deviceX/scan_elements/in_pulseY_type
+What:		/sys/.../iio:deviceX/scan_elements/in_pulse_type
 KernelVersion:	2.6.37
 Contact:	linux-iio@vger.kernel.org
 Description:
@@ -845,6 +861,8 @@ What:		/sys/.../iio:deviceX/scan_elements/in_incli_y_index
 What:		/sys/.../iio:deviceX/scan_elements/in_timestamp_index
 What:		/sys/.../iio:deviceX/scan_elements/in_pressureY_index
 What:		/sys/.../iio:deviceX/scan_elements/in_pressure_index
+What:		/sys/.../iio:deviceX/scan_elements/in_pulseY_index
+What:		/sys/.../iio:deviceX/scan_elements/in_pulse_index
 KernelVersion:	2.6.37
 Contact:	linux-iio@vger.kernel.org
 Description:
diff --git a/Documentation/ABI/testing/sysfs-bus-iio-pulse-tiecap b/Documentation/ABI/testing/sysfs-bus-iio-pulse-tiecap
new file mode 100644
index 0000000..a9e4a9f
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-bus-iio-pulse-tiecap
@@ -0,0 +1,9 @@
+What:		/sys/bus/iio/devices/iio:deviceX/pulse_polarityY
+What:		/sys/bus/iio/devices/iio:deviceX/pulse_polarity
+Date:		January 2014
+KernelVersion:	3.15
+Contact:	Matt Porter <mporter@linaro.org>
+Description:
+		Get and set the polarity of the pulse signal to be captured
+		for channel Y.  1 indicates a high pulse signal and 0
+		indicates a low pulse signal.
-- 
1.8.4

[PATCH v2 6/6] ARM: dts: AM33XX: Add ecap interrupt properties

[Matt Porter]

Add missing interrupt properties to the ecap0, ecap1, and ecap2
nodes.

Signed-off-by: Matt Porter <mporter@linaro.org>
---
 arch/arm/boot/dts/am33xx.dtsi | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi
index 6d95d3d..b4139ba 100644
--- a/arch/arm/boot/dts/am33xx.dtsi
+++ b/arch/arm/boot/dts/am33xx.dtsi
@@ -582,6 +582,8 @@
 				compatible = "ti,am33xx-ecap";
 				#pwm-cells = <3>;
 				reg = <0x48300100 0x80>;
+				interrupts = <31>;
+				interrupt-names = "ecap0";
 				ti,hwmods = "ecap0";
 				status = "disabled";
 			};
@@ -610,6 +612,8 @@
 				compatible = "ti,am33xx-ecap";
 				#pwm-cells = <3>;
 				reg = <0x48302100 0x80>;
+				interrupts = <47>;
+				interrupt-names = "ecap1";
 				ti,hwmods = "ecap1";
 				status = "disabled";
 			};
@@ -638,6 +642,8 @@
 				compatible = "ti,am33xx-ecap";
 				#pwm-cells = <3>;
 				reg = <0x48304100 0x80>;
+				interrupts = <61>;
+				interrupt-names = "ecap2";
 				ti,hwmods = "ecap2";
 				status = "disabled";
 			};
-- 
1.8.4