[PATCH v6 3/8] ARM: brcmstb: add debug UART for earlyprintk support

[Marc Carino <marc.ceeeee@gmail.com>]

Add the UART definitions needed to support earlyprintk on brcmstb machines.

Signed-off-by: Marc Carino <marc.ceeeee@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
---
 arch/arm/Kconfig.debug |   15 ++++++++++++++-
 1 files changed, 14 insertions(+), 1 deletions(-)

diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug
index 0531da8..5d7f76b 100644
--- a/arch/arm/Kconfig.debug
+++ b/arch/arm/Kconfig.debug
@@ -125,6 +125,17 @@ choice
 		  Say Y here if you want kernel low-level debugging support
 		  on Marvell Berlin SoC based platforms.
 
+	config DEBUG_BRCMSTB_UART
+		bool "Use BRCMSTB UART for low-level debug"
+		depends on ARCH_BRCMSTB
+		select DEBUG_UART_8250
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to the first serial port on these devices.
+
+		  If you have a Broadcom STB chip and would like early print
+		  messages to appear over the UART, select this option.
+
 	config DEBUG_CLPS711X_UART1
 		bool "Kernel low-level debugging messages via UART1"
 		depends on ARCH_CLPS711X
@@ -1049,6 +1060,7 @@ config DEBUG_UART_PHYS
 	default 0xd4018000 if DEBUG_MMP_UART3
 	default 0xe0000000 if ARCH_SPEAR13XX
 	default 0xf0000be0 if ARCH_EBSA110
+	default 0xf0406b00 if DEBUG_BRCMSTB_UART
 	default 0xf1012000 if DEBUG_MVEBU_UART_ALTERNATE
 	default 0xf1012000 if ARCH_DOVE || ARCH_KIRKWOOD || ARCH_MV78XX0 || \
 				ARCH_ORION5X
@@ -1083,6 +1095,7 @@ config DEBUG_UART_VIRT
 	default 0xf8090000 if DEBUG_VEXPRESS_UART0_RS1
 	default 0xfb009000 if DEBUG_REALVIEW_STD_PORT
 	default 0xfb10c000 if DEBUG_REALVIEW_PB1176_PORT
+	default 0xfc406b00 if DEBUG_BRCMSTB_UART
 	default 0xfd000000 if ARCH_SPEAR3XX || ARCH_SPEAR6XX
 	default 0xfd000000 if ARCH_SPEAR13XX
 	default 0xfd012000 if ARCH_MV78XX0
@@ -1136,7 +1149,7 @@ config DEBUG_UART_8250_WORD
 		ARCH_KEYSTONE || \
 		DEBUG_DAVINCI_DMx_UART0 || DEBUG_DAVINCI_DA8XX_UART1 || \
 		DEBUG_DAVINCI_DA8XX_UART2 || DEBUG_DAVINCI_TNETV107X_UART1 || \
-		DEBUG_BCM_KONA_UART
+		DEBUG_BCM_KONA_UART || DEBUG_BRCMSTB_UART
 
 config DEBUG_UART_8250_FLOW_CONTROL
 	bool "Enable flow control for 8250 UART"
-- 
1.7.1