* [PATCH 1/4] ARM: dts: omap3: Add support for INCOstartec a83x module
2014-01-27 0:33 [PATCH v3 0/4] ARM: add omap3 INCOstartec board support Christoph Fritz
@ 2014-01-27 0:33 ` Christoph Fritz
2014-01-27 0:33 ` [PATCH 2/4] ARM: dts: omap3: Add support for INCOstartec DBB056 baseboard Christoph Fritz
` (3 subsequent siblings)
4 siblings, 0 replies; 6+ messages in thread
From: Christoph Fritz @ 2014-01-27 0:33 UTC (permalink / raw)
To: Nishanth Menon, Tero Kristo, Javier Martinez Canillas,
Ulf Hansson, Mark Rutland, Ian Campbell, Tony Lindgren,
Tomi Valkeinen, bcousson, Daniel Mack, Hans J. Koch
Cc: devicetree, linux-arm-kernel, linux-omap
INCOstartec LILLY-A83X module is a TI DM3730xx100 (OMAP3) SoC
computer-on-module.
This patch adds device tree support for most of its features.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
---
arch/arm/boot/dts/omap3-lilly-a83x.dtsi | 459 +++++++++++++++++++++++++++++++
1 file changed, 459 insertions(+)
create mode 100644 arch/arm/boot/dts/omap3-lilly-a83x.dtsi
diff --git a/arch/arm/boot/dts/omap3-lilly-a83x.dtsi b/arch/arm/boot/dts/omap3-lilly-a83x.dtsi
new file mode 100644
index 0000000..6369d9f
--- /dev/null
+++ b/arch/arm/boot/dts/omap3-lilly-a83x.dtsi
@@ -0,0 +1,459 @@
+/*
+ * Copyright (C) 2014 Christoph Fritz <chf.fritzc@googlemail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include "omap36xx.dtsi"
+
+/ {
+ model = "INCOstartec LILLY-A83X module (DM3730)";
+ compatible = "incostartec,omap3-lilly-a83x", "ti,omap36xx", "ti,omap3";
+
+ chosen {
+ bootargs = "console=ttyO0,115200n8 vt.global_cursor_default=0 consoleblank=0";
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x8000000>; /* 128 MB */
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led1 {
+ label = "lilly-a83x::led1";
+ gpios = <&gpio1 29 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "default-on";
+ };
+
+ };
+
+ sound {
+ compatible = "ti,omap-twl4030";
+ ti,model = "lilly-a83x";
+
+ ti,mcbsp = <&mcbsp2>;
+ ti,codec = <&twl_audio>;
+ };
+
+ reg_vcc3: vcc3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ hsusb1_phy: hsusb1_phy {
+ compatible = "usb-nop-xceiv";
+ vcc-supply = <®_vcc3>;
+ };
+};
+
+&omap3_pmx_wkup {
+ pinctrl-names = "default";
+
+ lan9221_pins: pinmux_lan9221_pins {
+ pinctrl-single,pins = <
+ OMAP3_WKUP_IOPAD(0x2a5a, PIN_INPUT | MUX_MODE4) /* reserved.gpio_129 */
+ >;
+ };
+
+ tsc2048_pins: pinmux_tsc2048_pins {
+ pinctrl-single,pins = <
+ OMAP3_WKUP_IOPAD(0x2a16, PIN_INPUT_PULLUP | MUX_MODE4) /* sys_boot6.gpio_8 */
+ >;
+ };
+
+ mmc1cd_pins: pinmux_mmc1cd_pins {
+ pinctrl-single,pins = <
+ OMAP3_WKUP_IOPAD(0x2a56, PIN_INPUT | MUX_MODE4) /* reserved.gpio_126 */
+ >;
+ };
+};
+
+&omap3_pmx_core {
+ pinctrl-names = "default";
+
+ uart1_pins: pinmux_uart1_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x217c, PIN_OUTPUT | MUX_MODE0) /* uart1_tx.uart1_tx */
+ OMAP3_CORE1_IOPAD(0x217e, PIN_OUTPUT | MUX_MODE0) /* uart1_rts.uart1_rts */
+ OMAP3_CORE1_IOPAD(0x2180, PIN_INPUT | MUX_MODE0) /* uart1_cts.uart1_cts */
+ OMAP3_CORE1_IOPAD(0x2182, PIN_INPUT | MUX_MODE0) /* uart1_rx.uart1_rx */
+ >;
+ };
+
+ uart2_pins: pinmux_uart2_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x2170, PIN_OUTPUT | MUX_MODE1) /* mcbsp3_clkx.uart2_tx */
+ OMAP3_CORE1_IOPAD(0x2172, PIN_INPUT | MUX_MODE1) /* mcbsp3_fsx.uart2_rx */
+ >;
+ };
+
+ uart3_pins: pinmux_uart3_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
+ OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */
+ >;
+ };
+
+ i2c1_pins: pinmux_i2c1_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x21ba ,PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl.i2c1_scl */
+ OMAP3_CORE1_IOPAD(0x21bc ,PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda.i2c1_sda */
+ >;
+ };
+
+ i2c2_pins: pinmux_i2c2_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x21be, PIN_INPUT | MUX_MODE0) /* i2c2_scl.i2c2_scl */
+ OMAP3_CORE1_IOPAD(0x21c0, PIN_INPUT | MUX_MODE0) /* i2c2_sda.i2c2_sda */
+ >;
+ };
+
+ i2c3_pins: pinmux_i2c3_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x21c2, PIN_INPUT | MUX_MODE0) /* i2c3_scl.i2c3_scl */
+ OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT | MUX_MODE0) /* i2c3_sda.i2c3_sda */
+ >;
+ };
+
+ hsusb1_pins: pinmux_hsusb1_pins {
+ pinctrl-single,pins = <
+
+ /* GPIO 182 controls USB-Hub reset. But USB-Phy its
+ * reset can't be controlled. So we clamp this GPIO to
+ * high (PIN_OFF_OUTPUT_HIGH) to always enable USB-Hub.
+ */
+
+ OMAP3_CORE1_IOPAD(0x21de, PIN_OUTPUT_PULLUP | PIN_OFF_OUTPUT_HIGH | MUX_MODE4) /* mcspi2_cs1.gpio_182 */
+ >;
+ };
+
+ hsusb_otg_pins: pinmux_hsusb_otg_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x21a2, PIN_INPUT | MUX_MODE0) /* hsusb0_clk.hsusb0_clk */
+ OMAP3_CORE1_IOPAD(0x21a4, PIN_OUTPUT | MUX_MODE0) /* hsusb0_stp.hsusb0_stp */
+ OMAP3_CORE1_IOPAD(0x21a6, PIN_INPUT | MUX_MODE0) /* hsusb0_dir.hsusb0_dir */
+ OMAP3_CORE1_IOPAD(0x21a8, PIN_INPUT | MUX_MODE0) /* hsusb0_nxt.hsusb0_nxt */
+ OMAP3_CORE1_IOPAD(0x21aa, PIN_INPUT | MUX_MODE0) /* hsusb0_data0.hsusb0_data0 */
+ OMAP3_CORE1_IOPAD(0x21ac, PIN_INPUT | MUX_MODE0) /* hsusb0_data1.hsusb0_data1 */
+ OMAP3_CORE1_IOPAD(0x21ae, PIN_INPUT | MUX_MODE0) /* hsusb0_data2.hsusb0_data2 */
+ OMAP3_CORE1_IOPAD(0x21b0, PIN_INPUT | MUX_MODE0) /* hsusb0_data3.hsusb0_data3 */
+ OMAP3_CORE1_IOPAD(0x21b2, PIN_INPUT | MUX_MODE0) /* hsusb0_data4.hsusb0_data4 */
+ OMAP3_CORE1_IOPAD(0x21b4, PIN_INPUT | MUX_MODE0) /* hsusb0_data5.hsusb0_data5 */
+ OMAP3_CORE1_IOPAD(0x21b6, PIN_INPUT | MUX_MODE0) /* hsusb0_data6.hsusb0_data6 */
+ OMAP3_CORE1_IOPAD(0x21b8, PIN_INPUT | MUX_MODE0) /* hsusb0_data7.hsusb0_data7 */
+ >;
+ };
+
+ mmc1_pins: pinmux_mmc1_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */
+ OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */
+ OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */
+ OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */
+ OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */
+ OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */
+ >;
+ };
+
+ spi2_pins: pinmux_spi2_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcspi2_clk.mcspi2_clk */
+ OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcspi2_simo.mcspi2_simo */
+ OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcspi2_somi.mcspi2_somi */
+ OMAP3_CORE1_IOPAD(0x21dc, PIN_OUTPUT | MUX_MODE0) /* mcspi2_cs0.mcspi2_cs0 */
+ >;
+ };
+};
+
+&omap3_pmx_core2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ &hsusb1_2_pins
+ >;
+
+ hsusb1_2_pins: pinmux_hsusb1_2_pins {
+ pinctrl-single,pins = <
+ OMAP3630_CORE2_IOPAD(0x25d8, PIN_OUTPUT | MUX_MODE3) /* etk_clk.hsusb1_stp */
+ OMAP3630_CORE2_IOPAD(0x25da, PIN_INPUT | MUX_MODE3) /* etk_ctl.hsusb1_clk */
+ OMAP3630_CORE2_IOPAD(0x25dc, PIN_INPUT | MUX_MODE3) /* etk_d0.hsusb1_data0 */
+ OMAP3630_CORE2_IOPAD(0x25de, PIN_INPUT | MUX_MODE3) /* etk_d1.hsusb1_data1 */
+ OMAP3630_CORE2_IOPAD(0x25e0, PIN_INPUT | MUX_MODE3) /* etk_d2.hsusb1_data2 */
+ OMAP3630_CORE2_IOPAD(0x25e2, PIN_INPUT | MUX_MODE3) /* etk_d3.hsusb1_data7 */
+ OMAP3630_CORE2_IOPAD(0x25e4, PIN_INPUT | MUX_MODE3) /* etk_d4.hsusb1_data4 */
+ OMAP3630_CORE2_IOPAD(0x25e6, PIN_INPUT | MUX_MODE3) /* etk_d5.hsusb1_data5 */
+ OMAP3630_CORE2_IOPAD(0x25e8, PIN_INPUT | MUX_MODE3) /* etk_d6.hsusb1_data6 */
+ OMAP3630_CORE2_IOPAD(0x25ea, PIN_INPUT | MUX_MODE3) /* etk_d7.hsusb1_data3 */
+ OMAP3630_CORE2_IOPAD(0x25ec, PIN_INPUT | MUX_MODE3) /* etk_d8.hsusb1_dir */
+ OMAP3630_CORE2_IOPAD(0x25ee, PIN_INPUT | MUX_MODE3) /* etk_d9.hsusb1_nxt */
+ >;
+ };
+
+ gpio1_pins: pinmux_gpio1_pins {
+ pinctrl-single,pins = <
+ OMAP3630_CORE2_IOPAD(0x25fa, PIN_OUTPUT_PULLDOWN | MUX_MODE4) /* etk_d15.gpio_29 */
+ >;
+ };
+
+};
+
+&gpio1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio1_pins>;
+};
+
+&gpio6 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hsusb1_pins>;
+};
+
+&i2c1 {
+ clock-frequency = <2600000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
+
+ twl: twl@48 {
+ reg = <0x48>;
+ interrupts = <7>; /* SYS_NIRQ cascaded to intc */
+ interrupt-parent = <&intc>;
+
+ twl_audio: audio {
+ compatible = "ti,twl4030-audio";
+ codec {
+ };
+ };
+ };
+};
+
+#include "twl4030.dtsi"
+#include "twl4030_omap3.dtsi"
+
+&twl {
+ vmmc1: regulator-vmmc1 {
+ regulator-always-on;
+ };
+
+ vdd1: regulator-vdd1 {
+ regulator-always-on;
+ };
+
+ vdd2: regulator-vdd2 {
+ regulator-always-on;
+ };
+};
+
+&i2c2 {
+ clock-frequency = <2600000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins>;
+};
+
+&i2c3 {
+ clock-frequency = <2600000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c3_pins>;
+ gpiom1: gpio@20 {
+ compatible = "mcp,mcp23017";
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x20>;
+ };
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins>;
+};
+
+&uart4 {
+ status = "disabled";
+};
+
+&mmc1 {
+ cd-gpios = <&gpio4 30 IRQ_TYPE_LEVEL_LOW>;
+ cd-inverted;
+ vmmc-supply = <&vmmc1>;
+ bus-width = <4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins &mmc1cd_pins>;
+ cap-sdio-irq;
+ cap-sd-highspeed;
+ cap-mmc-highspeed;
+};
+
+&mmc2 {
+ status = "disabled";
+};
+
+&mmc3 {
+ status = "disabled";
+};
+
+&mcspi2 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2_pins>;
+
+ tsc2046@0 {
+ reg = <0>; /* CS0 */
+ compatible = "ti,tsc2046";
+ interrupt-parent = <&gpio1>;
+ interrupts = <8 0>; /* boot6 / gpio_8 */
+ spi-max-frequency = <1000000>;
+ pendown-gpio = <&gpio1 8 0>;
+ vcc-supply = <®_vcc3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&tsc2048_pins>;
+
+ ti,x-min = <300>;
+ ti,x-max = <3000>;
+ ti,y-min = <600>;
+ ti,y-max = <3600>;
+ ti,x-plate-ohms = <80>;
+ ti,pressure-max = <255>;
+ ti,swap-xy;
+
+ linux,wakeup;
+ };
+};
+
+&usbhsehci {
+ phys = <&hsusb1_phy>;
+};
+
+&usbhshost {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hsusb1_2_pins>;
+ num-ports = <2>;
+ port1-mode = "ehci-phy";
+};
+
+&usb_otg_hs {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hsusb_otg_pins>;
+ interface-type = <0>;
+ usb-phy = <&usb2_phy>;
+ phys = <&usb2_phy>;
+ phy-names = "usb2-phy";
+ mode = <3>;
+ power = <50>;
+};
+
+&gpmc {
+ ranges = <0 0 0x30000000 0x1000000>,
+ <7 0 0x15000000 0x01000000>;
+
+ nand@0,0 {
+ reg = <0 0 0x1000000>;
+ nand-bus-width = <16>;
+ ti,nand-ecc-opt = "bch8";
+ /* no elm on omap3 */
+
+ gpmc,mux-add-data = <0>;
+ gpmc,device-nand;
+ gpmc,device-width = <2>;
+ gpmc,wait-pin = <0>;
+ gpmc,wait-monitoring-ns = <0>;
+ gpmc,burst-length= <4>;
+ gpmc,cs-on-ns = <0>;
+ gpmc,cs-rd-off-ns = <100>;
+ gpmc,cs-wr-off-ns = <100>;
+ gpmc,adv-on-ns = <0>;
+ gpmc,adv-rd-off-ns = <100>;
+ gpmc,adv-wr-off-ns = <100>;
+ gpmc,oe-on-ns = <5>;
+ gpmc,oe-off-ns = <75>;
+ gpmc,we-on-ns = <5>;
+ gpmc,we-off-ns = <75>;
+ gpmc,rd-cycle-ns = <100>;
+ gpmc,wr-cycle-ns = <100>;
+ gpmc,access-ns = <60>;
+ gpmc,page-burst-access-ns = <5>;
+ gpmc,bus-turnaround-ns = <0>;
+ gpmc,cycle2cycle-samecsen;
+ gpmc,cycle2cycle-delay-ns = <50>;
+ gpmc,wr-data-mux-bus-ns = <75>;
+ gpmc,wr-access-ns = <155>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "MLO";
+ reg = <0 0x80000>;
+ };
+
+ partition@0x80000 {
+ label = "u-boot";
+ reg = <0x80000 0x1e0000>;
+ };
+
+ partition@0x260000 {
+ label = "u-boot-environment";
+ reg = <0x260000 0x20000>;
+ };
+
+ partition@0x280000 {
+ label = "kernel";
+ reg = <0x280000 0x500000>;
+ };
+
+ partition@0x780000 {
+ label = "filesystem";
+ reg = <0x780000 0xf880000>;
+ };
+ };
+
+ ethernet@7,0 {
+ compatible = "smsc,lan9221", "smsc,lan9115";
+ bank-width = <2>;
+ gpmc,mux-add-data = <2>;
+ gpmc,cs-on-ns = <10>;
+ gpmc,cs-rd-off-ns = <60>;
+ gpmc,cs-wr-off-ns = <60>;
+ gpmc,adv-on-ns = <0>;
+ gpmc,adv-rd-off-ns = <10>;
+ gpmc,adv-wr-off-ns = <10>;
+ gpmc,oe-on-ns = <10>;
+ gpmc,oe-off-ns = <60>;
+ gpmc,we-on-ns = <10>;
+ gpmc,we-off-ns = <60>;
+ gpmc,rd-cycle-ns = <100>;
+ gpmc,wr-cycle-ns = <100>;
+ gpmc,access-ns = <50>;
+ gpmc,page-burst-access-ns = <5>;
+ gpmc,bus-turnaround-ns = <0>;
+ gpmc,cycle2cycle-delay-ns = <75>;
+ gpmc,wr-data-mux-bus-ns = <15>;
+ gpmc,wr-access-ns = <75>;
+ gpmc,cycle2cycle-samecsen;
+ gpmc,cycle2cycle-diffcsen;
+ vddvario-supply = <®_vcc3>;
+ vdd33a-supply = <®_vcc3>;
+ reg-io-width = <4>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <1 0x2>;
+ reg = <7 0 0xff>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&lan9221_pins>;
+ phy-mode = "mii";
+ };
+};
--
1.7.10.4
^ permalink raw reply related [flat|nested] 6+ messages in thread* [PATCH 2/4] ARM: dts: omap3: Add support for INCOstartec DBB056 baseboard
2014-01-27 0:33 [PATCH v3 0/4] ARM: add omap3 INCOstartec board support Christoph Fritz
2014-01-27 0:33 ` [PATCH 1/4] ARM: dts: omap3: Add support for INCOstartec a83x module Christoph Fritz
@ 2014-01-27 0:33 ` Christoph Fritz
2014-01-27 0:33 ` [PATCH 3/4] ARM: OMAP2+: add legacy display for omap3 DBB056 Christoph Fritz
` (2 subsequent siblings)
4 siblings, 0 replies; 6+ messages in thread
From: Christoph Fritz @ 2014-01-27 0:33 UTC (permalink / raw)
To: Nishanth Menon, Tero Kristo, Javier Martinez Canillas,
Ulf Hansson, Mark Rutland, Ian Campbell, Tony Lindgren,
Tomi Valkeinen, bcousson, Daniel Mack, Hans J. Koch
Cc: devicetree, linux-arm-kernel, linux-omap
INCOstartec LILLY-DBB056 is a carrier board (baseboard) for
computer-on-module LILLY-A83X.
This patch adds device-tree support for most of its features.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/omap3-lilly-dbb056.dts | 165 ++++++++++++++++++++++++++++++
2 files changed, 166 insertions(+)
create mode 100644 arch/arm/boot/dts/omap3-lilly-dbb056.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index cfd364d..b449161 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -215,6 +215,7 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \
omap3-gta04.dtb \
omap3-igep0020.dtb \
omap3-igep0030.dtb \
+ omap3-lilly-dbb056.dtb \
omap3-zoom3.dtb \
omap4-panda.dtb \
omap4-panda-a4.dtb \
diff --git a/arch/arm/boot/dts/omap3-lilly-dbb056.dts b/arch/arm/boot/dts/omap3-lilly-dbb056.dts
new file mode 100644
index 0000000..89e2b68
--- /dev/null
+++ b/arch/arm/boot/dts/omap3-lilly-dbb056.dts
@@ -0,0 +1,165 @@
+/*
+ * Copyright (C) 2014 Christoph Fritz <chf.fritzc@googlemail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+/dts-v1/;
+
+#include "omap3-lilly-a83x.dtsi"
+
+/ {
+ model = "INCOstartec LILLY-DBB056 (DM3730)";
+ compatible = "incostartec,omap3-lilly-dbb056", "incostartec,omap3-lilly-a83x", "ti,omap36xx", "ti,omap3";
+};
+
+&twl {
+ vaux2: regulator-vaux2 {
+ compatible = "ti,twl4030-vaux2";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ };
+};
+
+&vpll2 {
+ /* Needed for DSS */
+ regulator-name = "vdds_dsi";
+};
+
+&omap3_pmx_core {
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcd_pins>;
+
+ lan9117_pins: pinmux_lan9117_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x2114, PIN_INPUT | MUX_MODE4) /* cam_fld.gpio_98 */
+ >;
+ };
+
+ gpio4_pins: pinmux_gpio4_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x212e, PIN_INPUT | MUX_MODE4) /* cam_xclkb.gpio_111 -> sja1000 IRQ */
+ >;
+ };
+
+ lcd_pins: pinmux_lcd_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0) /* dss_pclk.dss_pclk */
+ OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0) /* dss_hsync.dss_hsync */
+ OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT | MUX_MODE0) /* dss_vsync.dss_vsync */
+ OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT | MUX_MODE0) /* dss_acbias.dss_acbias */
+ OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT | MUX_MODE0) /* dss_data0.dss_data0 */
+ OMAP3_CORE1_IOPAD(0x20de, PIN_OUTPUT | MUX_MODE0) /* dss_data1.dss_data1 */
+ OMAP3_CORE1_IOPAD(0x20e0, PIN_OUTPUT | MUX_MODE0) /* dss_data2.dss_data2 */
+ OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE0) /* dss_data3.dss_data3 */
+ OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT | MUX_MODE0) /* dss_data4.dss_data4 */
+ OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT | MUX_MODE0) /* dss_data5.dss_data5 */
+ OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT | MUX_MODE0) /* dss_data6.dss_data6 */
+ OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT | MUX_MODE0) /* dss_data7.dss_data7 */
+ OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT | MUX_MODE0) /* dss_data8.dss_data8 */
+ OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT | MUX_MODE0) /* dss_data9.dss_data9 */
+ OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE0) /* dss_data10.dss_data10 */
+ OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE0) /* dss_data11.dss_data11 */
+ OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT | MUX_MODE0) /* dss_data12.dss_data12 */
+ OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT | MUX_MODE0) /* dss_data13.dss_data13 */
+ OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT | MUX_MODE0) /* dss_data14.dss_data14 */
+ OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT | MUX_MODE0) /* dss_data15.dss_data15 */
+ OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT | MUX_MODE0) /* dss_data16.dss_data16 */
+ OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT | MUX_MODE0) /* dss_data17.dss_data17 */
+ OMAP3_CORE1_IOPAD(0x218c, PIN_OUTPUT | MUX_MODE4) /* mcbsp1_clk.gpio_156 -> enable DSS */
+ >;
+ };
+
+ mmc2_pins: pinmux_mmc2_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */
+ OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */
+ OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */
+ OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */
+ OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */
+ OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */
+ OMAP3_CORE1_IOPAD(0x2164, PIN_OUTPUT | MUX_MODE1) /* sdmmc2_dat4.sdmmc2_dir_dat0 */
+ OMAP3_CORE1_IOPAD(0x2166, PIN_OUTPUT | MUX_MODE1) /* sdmmc2_dat5.sdmmc2_dir_dat1 */
+ OMAP3_CORE1_IOPAD(0x2168, PIN_OUTPUT | MUX_MODE1) /* sdmmc2_dat6.sdmmc2_dir_cmd */
+ OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT | MUX_MODE1) /* sdmmc2_dat7.sdmmc2_clkin */
+ OMAP3_CORE1_IOPAD(0x219a, PIN_INPUT_PULLUP | MUX_MODE4) /* uart3_cts_rctx.gpio_163 -> wp */
+ OMAP3_CORE1_IOPAD(0x219c, PIN_INPUT_PULLUP | MUX_MODE4) /* uart3_rts_sd.gpio_164 -> cd */
+ >;
+ };
+
+ spi1_pins: pinmux_spi1_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT | MUX_MODE0) /* mcspi1_clk.mcspi1_clk */
+ OMAP3_CORE1_IOPAD(0x21ca, PIN_INPUT | MUX_MODE0) /* mcspi1_simo.mcspi1_simo */
+ OMAP3_CORE1_IOPAD(0x21cc, PIN_INPUT | MUX_MODE0) /* mcspi1_somi.mcspi1_somi */
+ OMAP3_CORE1_IOPAD(0x21ce, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcspi1_cs0.mcspi1_cs0 */
+ >;
+ };
+};
+
+&gpio4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio4_pins>;
+};
+
+&mmc2 {
+ status = "okay";
+ bus-width = <4>;
+ vmmc-supply = <&vmmc1>;
+ cd-gpios = <&gpio6 4 0>; /* gpio_164 */
+ wp-gpios = <&gpio6 3 0>; /* gpio_163 */
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_pins>;
+ ti,dual-volt;
+};
+
+&mcspi1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi1_pins>;
+};
+
+&gpmc {
+ ranges = <0 0 0x30000000 0x1000000>, /* nand assigned by COM a83x */
+ <4 0 0x20000000 0x01000000>,
+ <7 0 0x15000000 0x01000000>; /* eth assigend by COM a83x */
+
+ ethernet@4,0 {
+ compatible = "smsc,lan9117", "smsc,lan9115";
+ bank-width = <2>;
+ gpmc,mux-add-data = <2>;
+ gpmc,cs-on-ns = <10>;
+ gpmc,cs-rd-off-ns = <65>;
+ gpmc,cs-wr-off-ns = <65>;
+ gpmc,adv-on-ns = <0>;
+ gpmc,adv-rd-off-ns = <10>;
+ gpmc,adv-wr-off-ns = <10>;
+ gpmc,oe-on-ns = <10>;
+ gpmc,oe-off-ns = <65>;
+ gpmc,we-on-ns = <10>;
+ gpmc,we-off-ns = <65>;
+ gpmc,rd-cycle-ns = <100>;
+ gpmc,wr-cycle-ns = <100>;
+ gpmc,access-ns = <60>;
+ gpmc,page-burst-access-ns = <5>;
+ gpmc,bus-turnaround-ns = <0>;
+ gpmc,cycle2cycle-delay-ns = <75>;
+ gpmc,wr-data-mux-bus-ns = <15>;
+ gpmc,wr-access-ns = <75>;
+ gpmc,cycle2cycle-samecsen;
+ gpmc,cycle2cycle-diffcsen;
+ vddvario-supply = <®_vcc3>;
+ vdd33a-supply = <®_vcc3>;
+ reg-io-width = <4>;
+ interrupt-parent = <&gpio4>;
+ interrupts = <2 0x2>;
+ reg = <4 0 0xff>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&lan9117_pins>;
+ phy-mode = "mii";
+ smsc,force-internal-phy;
+ };
+};
--
1.7.10.4
^ permalink raw reply related [flat|nested] 6+ messages in thread* [PATCH 3/4] ARM: OMAP2+: add legacy display for omap3 DBB056
2014-01-27 0:33 [PATCH v3 0/4] ARM: add omap3 INCOstartec board support Christoph Fritz
2014-01-27 0:33 ` [PATCH 1/4] ARM: dts: omap3: Add support for INCOstartec a83x module Christoph Fritz
2014-01-27 0:33 ` [PATCH 2/4] ARM: dts: omap3: Add support for INCOstartec DBB056 baseboard Christoph Fritz
@ 2014-01-27 0:33 ` Christoph Fritz
2014-01-27 0:33 ` [PATCH 4/4] ARM: OMAP2+: Add pdata quirk for sys_clkout2 " Christoph Fritz
[not found] ` <1390782797-24105-1-git-send-email-chf.fritz-gM/Ye1E23mwN+BqQ9rBEUg@public.gmane.org>
4 siblings, 0 replies; 6+ messages in thread
From: Christoph Fritz @ 2014-01-27 0:33 UTC (permalink / raw)
To: Nishanth Menon, Tero Kristo, Javier Martinez Canillas,
Ulf Hansson, Mark Rutland, Ian Campbell, Tony Lindgren,
Tomi Valkeinen, bcousson, Daniel Mack, Hans J. Koch
Cc: devicetree, linux-arm-kernel, linux-omap
Full device tree support for omapdss is not yet accomplished. Until
then, init display by legacy platform code.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
---
arch/arm/mach-omap2/dss-common.c | 49 ++++++++++++++++++++++++++++++++++++
arch/arm/mach-omap2/dss-common.h | 1 +
arch/arm/mach-omap2/pdata-quirks.c | 8 +++++-
3 files changed, 57 insertions(+), 1 deletion(-)
diff --git a/arch/arm/mach-omap2/dss-common.c b/arch/arm/mach-omap2/dss-common.c
index dadccc9..b8b4e39 100644
--- a/arch/arm/mach-omap2/dss-common.c
+++ b/arch/arm/mach-omap2/dss-common.c
@@ -257,3 +257,52 @@ void __init omap3_igep2_display_init_of(void)
platform_device_register(&omap3_igep2_tfp410_device);
platform_device_register(&omap3_igep2_dvi_connector_device);
}
+
+/* OMAP3 dbb056 data */
+
+#define DBB056_DISPLAY_ENABLE_GPIO 156
+
+static const struct display_timing dbb056_lcd_videomode = {
+ .pixelclock = { 0, 19200000, 0 },
+
+ .hactive = { 0, 640, 0 },
+ .hfront_porch = { 0, 104, 0 },
+ .hback_porch = { 0, 8, 0 },
+ .hsync_len = { 0, 8, 0 },
+
+ .vactive = { 0, 480, 0 },
+ .vfront_porch = { 0, 104, 0 },
+ .vback_porch = { 0, 8, 0 },
+ .vsync_len = { 0, 8, 0 },
+
+ .flags = DISPLAY_FLAGS_HSYNC_LOW | DISPLAY_FLAGS_VSYNC_LOW |
+ DISPLAY_FLAGS_DE_HIGH | DISPLAY_FLAGS_PIXDATA_NEGEDGE,
+};
+
+static struct panel_dpi_platform_data dbb056_lcd_pdata = {
+ .name = "lcd",
+ .source = "dpi.0",
+
+ .data_lines = 18,
+
+ .display_timing = &dbb056_lcd_videomode,
+
+ .enable_gpio = DBB056_DISPLAY_ENABLE_GPIO,
+ .backlight_gpio = -1,
+};
+
+static struct platform_device dbb056_lcd_device = {
+ .name = "panel-dpi",
+ .id = 0,
+ .dev.platform_data = &dbb056_lcd_pdata,
+};
+
+static struct omap_dss_board_info omap_dbb056_dss_data = {
+ .default_display_name = "lcd",
+};
+
+void __init omap3_dbb056_display_init_of(void)
+{
+ platform_device_register(&dbb056_lcd_device);
+ omap_display_init(&omap_dbb056_dss_data);
+}
diff --git a/arch/arm/mach-omap2/dss-common.h b/arch/arm/mach-omap2/dss-common.h
index a9becf0..a125b55 100644
--- a/arch/arm/mach-omap2/dss-common.h
+++ b/arch/arm/mach-omap2/dss-common.h
@@ -9,5 +9,6 @@
void __init omap4_panda_display_init_of(void);
void __init omap_4430sdp_display_init_of(void);
void __init omap3_igep2_display_init_of(void);
+void __init omap3_dbb056_display_init_of(void);
#endif
diff --git a/arch/arm/mach-omap2/pdata-quirks.c b/arch/arm/mach-omap2/pdata-quirks.c
index 3d5b24d..435a823 100644
--- a/arch/arm/mach-omap2/pdata-quirks.c
+++ b/arch/arm/mach-omap2/pdata-quirks.c
@@ -169,6 +169,11 @@ static void __init am3517_evm_legacy_init(void)
omap_ctrl_writel(v, AM35XX_CONTROL_IP_SW_RESET);
omap_ctrl_readl(AM35XX_CONTROL_IP_SW_RESET); /* OCP barrier */
}
+
+static void __init omap3_dbb056_legacy_init(void)
+{
+ omap3_dbb056_display_init_of();
+}
#endif /* CONFIG_ARCH_OMAP3 */
#ifdef CONFIG_ARCH_OMAP4
@@ -259,10 +264,11 @@ struct of_dev_auxdata omap_auxdata_lookup[] __initdata = {
static struct pdata_init pdata_quirks[] __initdata = {
#ifdef CONFIG_ARCH_OMAP3
{ "compulab,omap3-sbc-t3730", omap3_sbc_t3730_legacy_init, },
+ { "incostartec,omap3-lilly-dbb056", omap3_dbb056_legacy_init, },
+ { "isee,omap3-igep0020", omap3_igep0020_legacy_init, },
{ "nokia,omap3-n900", hsmmc2_internal_input_clk, },
{ "nokia,omap3-n9", hsmmc2_internal_input_clk, },
{ "nokia,omap3-n950", hsmmc2_internal_input_clk, },
- { "isee,omap3-igep0020", omap3_igep0020_legacy_init, },
{ "ti,omap3-evm-37xx", omap3_evm_legacy_init, },
{ "ti,omap3-zoom3", omap3_zoom_legacy_init, },
{ "ti,am3517-evm", am3517_evm_legacy_init, },
--
1.7.10.4
^ permalink raw reply related [flat|nested] 6+ messages in thread* [PATCH 4/4] ARM: OMAP2+: Add pdata quirk for sys_clkout2 for omap3 DBB056
2014-01-27 0:33 [PATCH v3 0/4] ARM: add omap3 INCOstartec board support Christoph Fritz
` (2 preceding siblings ...)
2014-01-27 0:33 ` [PATCH 3/4] ARM: OMAP2+: add legacy display for omap3 DBB056 Christoph Fritz
@ 2014-01-27 0:33 ` Christoph Fritz
[not found] ` <1390782797-24105-1-git-send-email-chf.fritz-gM/Ye1E23mwN+BqQ9rBEUg@public.gmane.org>
4 siblings, 0 replies; 6+ messages in thread
From: Christoph Fritz @ 2014-01-27 0:33 UTC (permalink / raw)
To: Nishanth Menon, Tero Kristo, Javier Martinez Canillas,
Ulf Hansson, Mark Rutland, Ian Campbell, Tony Lindgren,
Tomi Valkeinen, bcousson, Daniel Mack, Hans J. Koch
Cc: devicetree, linux-arm-kernel, linux-omap
Full device tree support for clock control, especially to set frequencies,
is not yet accomplished. Until then, configure the 24Mhz of sys_clkout2 to
feed an USB-Hub here.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
---
arch/arm/mach-omap2/pdata-quirks.c | 37 ++++++++++++++++++++++++++++++++++++
1 file changed, 37 insertions(+)
diff --git a/arch/arm/mach-omap2/pdata-quirks.c b/arch/arm/mach-omap2/pdata-quirks.c
index 435a823..e36ac3f 100644
--- a/arch/arm/mach-omap2/pdata-quirks.c
+++ b/arch/arm/mach-omap2/pdata-quirks.c
@@ -172,6 +172,43 @@ static void __init am3517_evm_legacy_init(void)
static void __init omap3_dbb056_legacy_init(void)
{
+ struct clk *clkout2;
+ struct clk *cm96fck;
+
+ /* Reparent clkout2 to 96M_FCK */
+ pr_info("%s: Late Reparent clkout2 to 96M_FCK\n", __func__);
+ clkout2 = clk_get(NULL, "clkout2_src_ck");
+ if (clkout2 < 0) {
+ pr_err("a83x-quirk: couldn't get clkout2_src_ck\n");
+ return;
+ }
+ cm96fck = clk_get(NULL, "cm_96m_fck");
+ if (cm96fck < 0) {
+ pr_err("a83x-quirk: couldn't get cm_96m_fck\n");
+ return;
+ }
+ if (clk_set_parent(clkout2, cm96fck) < 0) {
+ pr_err("a83x-quirk: couldn't reparent clkout2_src_ck\n");
+ return;
+ }
+
+ /* Set clkout2 to 24MHz for internal usb hub*/
+ pr_info("%s: Set clkout2 to 24MHz for internal usb hub\n", __func__);
+ clkout2 = clk_get(NULL, "sys_clkout2");
+ if (clkout2 < 0) {
+ pr_err("%s: couldn't get sys_clkout2\n", __func__);
+ return;
+ }
+ if (clk_set_rate(clkout2, 24000000) < 0) {
+ pr_err("%s: couldn't set sys_clkout2 rate\n", __func__);
+ return;
+ }
+ if (clk_prepare_enable(clkout2) < 0) {
+ pr_err("%s: couldn't enable sys_clkout2\n", __func__);
+ return;
+ }
+
+ /* Initialize display */
omap3_dbb056_display_init_of();
}
#endif /* CONFIG_ARCH_OMAP3 */
--
1.7.10.4
^ permalink raw reply related [flat|nested] 6+ messages in thread[parent not found: <1390782797-24105-1-git-send-email-chf.fritz-gM/Ye1E23mwN+BqQ9rBEUg@public.gmane.org>]
* Re: [PATCH v3 0/4] ARM: add omap3 INCOstartec board support
[not found] ` <1390782797-24105-1-git-send-email-chf.fritz-gM/Ye1E23mwN+BqQ9rBEUg@public.gmane.org>
@ 2014-02-07 10:19 ` Christoph Fritz
0 siblings, 0 replies; 6+ messages in thread
From: Christoph Fritz @ 2014-02-07 10:19 UTC (permalink / raw)
To: Nishanth Menon
Cc: Tero Kristo, Javier Martinez Canillas, Ulf Hansson, Mark Rutland,
Ian Campbell, Tony Lindgren, Tomi Valkeinen,
bcousson-rdvid1DuHRBWk0Htik3J/w, Daniel Mack, Hans J. Koch,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-omap-u79uwXL29TY76Z2rM5mHXA
On Mon, 2014-01-27 at 01:33 +0100, Christoph Fritz wrote:
> This set of patches adds board support for an omap3 system from INCOstartec.
> It's based on next-20140124.
>
> Due to a regression since next-20140115 the following errors are present:
>
> - pin sys_clkout2, which gets configured to 24 Mhz by the fourth patch
> in this set, erroneously outputs only 12 Mhz.
> Just out of curiosity, configuring it to 48 Mhz puts out desired 24 Mhz.
>
> - omap_dss, which gets configured by the third patch in this set, fails
> to do 'dss_set_fck_rate(fck);' in
> drivers/video/omap2/dss/dss.c:dss_setup_default_clock() which leads to:
>
> | omapdss_dss: probe of omapdss_dss failed with error -22
> | omapdss CORE error: Failed to initialize DSS platform driver
> | panel-dpi panel-dpi.0: failed to find video source 'dpi.0
>
> Both regressions seem to have something to do with the clock framework.
> Could this be related to the DT clock conversion patches?
Now with dt clock conversion fixes on its way, any chance to get this
upstream?
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 6+ messages in thread