* [PATCH v4 1/5] Documentation: dt: Add Kona PWM binding
2014-03-20 0:12 [PATCH v4 0/5] Add Broadcom Kona PWM Support Tim Kryger
@ 2014-03-20 0:12 ` Tim Kryger
2014-03-20 0:12 ` [PATCH v4 2/5] pwm: kona: Introduce Kona PWM controller support Tim Kryger
` (3 subsequent siblings)
4 siblings, 0 replies; 6+ messages in thread
From: Tim Kryger @ 2014-03-20 0:12 UTC (permalink / raw)
To: Thierry Reding, Matt Porter, Rob Herring, Pawel Moll,
Mark Rutland, Ian Campbell, Kumar Gala, Rob Landley,
Christian Daudt, Grant Likely
Cc: Tim Kryger, Linux PWM List, Device Tree List, Linux Doc List,
Linux Kernel Mailing List, Broadcom Kernel Feedback List,
Linux ARM Kernel List
Add the binding description for the Kona PWM controller found on Broadcom's
mobile SoCs.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
---
.../devicetree/bindings/pwm/bcm-kona-pwm.txt | 21 ++++++++++++++++++++
1 files changed, 21 insertions(+), 0 deletions(-)
create mode 100644 Documentation/devicetree/bindings/pwm/bcm-kona-pwm.txt
diff --git a/Documentation/devicetree/bindings/pwm/bcm-kona-pwm.txt b/Documentation/devicetree/bindings/pwm/bcm-kona-pwm.txt
new file mode 100644
index 0000000..8eae9fe
--- /dev/null
+++ b/Documentation/devicetree/bindings/pwm/bcm-kona-pwm.txt
@@ -0,0 +1,21 @@
+Broadcom Kona PWM controller device tree bindings
+
+This controller has 6 channels.
+
+Required Properties :
+- compatible: should contain "brcm,kona-pwm"
+- reg: physical base address and length of the controller's registers
+- clocks: phandle + clock specifier pair for the external clock
+- #pwm-cells: Should be 3. See pwm.txt in this directory for a
+ description of the cells format.
+
+Refer to clocks/clock-bindings.txt for generic clock consumer properties.
+
+Example:
+
+pwm: pwm@3e01a000 {
+ compatible = "brcm,bcm11351-pwm", "brcm,kona-pwm";
+ reg = <0x3e01a000 0xc4>;
+ clocks = <&pwm_clk>;
+ #pwm-cells = <3>;
+};
--
1.7.0.4
^ permalink raw reply related [flat|nested] 6+ messages in thread* [PATCH v4 2/5] pwm: kona: Introduce Kona PWM controller support
2014-03-20 0:12 [PATCH v4 0/5] Add Broadcom Kona PWM Support Tim Kryger
2014-03-20 0:12 ` [PATCH v4 1/5] Documentation: dt: Add Kona PWM binding Tim Kryger
@ 2014-03-20 0:12 ` Tim Kryger
2014-03-20 0:12 ` [PATCH v4 3/5] ARM: dts: Declare the PWM for bcm11351 (bcm281xx) Tim Kryger
` (2 subsequent siblings)
4 siblings, 0 replies; 6+ messages in thread
From: Tim Kryger @ 2014-03-20 0:12 UTC (permalink / raw)
To: Thierry Reding, Matt Porter, Rob Herring, Pawel Moll,
Mark Rutland, Ian Campbell, Kumar Gala, Rob Landley,
Christian Daudt, Grant Likely
Cc: Tim Kryger, Linux PWM List, Device Tree List, Linux Doc List,
Linux Kernel Mailing List, Broadcom Kernel Feedback List,
Linux ARM Kernel List
Add support for the six-channel Kona PWM controller found on Broadcom
mobile SoCs like bcm281xx.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
---
drivers/pwm/Kconfig | 10 ++
drivers/pwm/Makefile | 1 +
drivers/pwm/pwm-bcm-kona.c | 295 ++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 306 insertions(+), 0 deletions(-)
create mode 100644 drivers/pwm/pwm-bcm-kona.c
diff --git a/drivers/pwm/Kconfig b/drivers/pwm/Kconfig
index 22f2f28..1fd42af 100644
--- a/drivers/pwm/Kconfig
+++ b/drivers/pwm/Kconfig
@@ -62,6 +62,16 @@ config PWM_ATMEL_TCB
To compile this driver as a module, choose M here: the module
will be called pwm-atmel-tcb.
+config PWM_BCM_KONA
+ tristate "Kona PWM support"
+ depends on ARCH_BCM_MOBILE
+ default y
+ help
+ Generic PWM framework driver for Broadcom Kona PWM block.
+
+ To compile this driver as a module, choose M here: the module
+ will be called pwm-bcm-kona.
+
config PWM_BFIN
tristate "Blackfin PWM support"
depends on BFIN_GPTIMERS
diff --git a/drivers/pwm/Makefile b/drivers/pwm/Makefile
index d8906ec..7413090 100644
--- a/drivers/pwm/Makefile
+++ b/drivers/pwm/Makefile
@@ -3,6 +3,7 @@ obj-$(CONFIG_PWM_SYSFS) += sysfs.o
obj-$(CONFIG_PWM_AB8500) += pwm-ab8500.o
obj-$(CONFIG_PWM_ATMEL) += pwm-atmel.o
obj-$(CONFIG_PWM_ATMEL_TCB) += pwm-atmel-tcb.o
+obj-$(CONFIG_PWM_BCM_KONA) += pwm-bcm-kona.o
obj-$(CONFIG_PWM_BFIN) += pwm-bfin.o
obj-$(CONFIG_PWM_EP93XX) += pwm-ep93xx.o
obj-$(CONFIG_PWM_IMX) += pwm-imx.o
diff --git a/drivers/pwm/pwm-bcm-kona.c b/drivers/pwm/pwm-bcm-kona.c
new file mode 100644
index 0000000..7249b0d
--- /dev/null
+++ b/drivers/pwm/pwm-bcm-kona.c
@@ -0,0 +1,295 @@
+/*
+ * Copyright (C) 2014 Broadcom Corporation
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/ioport.h>
+#include <linux/math64.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/pwm.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+
+#define PWM_CONTROL_OFFSET (0x00000000)
+#define PWM_CONTROL_SMOOTH_SHIFT(chan) (24 + (chan))
+#define PWM_CONTROL_TYPE_SHIFT(chan) (16 + (chan))
+#define PWM_CONTROL_POLARITY_SHIFT(chan) (8 + (chan))
+#define PWM_CONTROL_ENABLE_SHIFT(chan) (chan)
+
+#define PRESCALE_OFFSET (0x00000004)
+#define PRESCALE_SHIFT(chan) ((chan) << 2)
+#define PRESCALE_MASK(chan) (0x7 << PRESCALE_SHIFT(chan))
+#define PRESCALE_MIN (0x00000000)
+#define PRESCALE_MAX (0x00000007)
+
+#define PERIOD_COUNT_OFFSET(chan) (0x00000008 + ((chan) << 3))
+#define PERIOD_COUNT_MIN (0x00000002)
+#define PERIOD_COUNT_MAX (0x00ffffff)
+
+#define DUTY_CYCLE_HIGH_OFFSET(chan) (0x0000000c + ((chan) << 3))
+#define DUTY_CYCLE_HIGH_MIN (0x00000000)
+#define DUTY_CYCLE_HIGH_MAX (0x00ffffff)
+
+struct kona_pwmc {
+ struct pwm_chip chip;
+ void __iomem *base;
+ struct clk *clk;
+};
+
+static inline struct kona_pwmc *to_kona_pwmc(struct pwm_chip *_chip)
+{
+ return container_of(_chip, struct kona_pwmc, chip);
+}
+
+static void kona_pwmc_apply_settings(struct kona_pwmc *kp, unsigned int chan)
+{
+ unsigned long value = readl(kp->base + PWM_CONTROL_OFFSET);
+
+ /*
+ * New duty and period settings are only reflected in the PWM output
+ * after a rising edge of the enable bit. When smooth bit is set, the
+ * new settings are delayed until the prior PWM period has completed.
+ * Furthermore, if the smooth bit is set, the PWM continues to output a
+ * waveform based on the old settings during the time that the enable
+ * bit is low. Otherwise the output is a constant high signal while
+ * the enable bit is low.
+ */
+
+ /* Clear enable bit but set smooth bit to maintain old output */
+ value |= 1 << PWM_CONTROL_SMOOTH_SHIFT(chan);
+ value &= ~(1 << PWM_CONTROL_ENABLE_SHIFT(chan));
+ writel(value, kp->base + PWM_CONTROL_OFFSET);
+
+ /* Set enable bit and clear smooth bit to apply new settings */
+ value &= ~(1 << PWM_CONTROL_SMOOTH_SHIFT(chan));
+ value |= 1 << PWM_CONTROL_ENABLE_SHIFT(chan);
+ writel(value, kp->base + PWM_CONTROL_OFFSET);
+}
+
+static int kona_pwmc_config(struct pwm_chip *chip, struct pwm_device *pwm,
+ int duty_ns, int period_ns)
+{
+ struct kona_pwmc *kp = to_kona_pwmc(chip);
+ u64 val, div, rate;
+ unsigned long prescale = PRESCALE_MIN, pc, dc;
+ unsigned int value, chan = pwm->hwpwm;
+
+ /*
+ * Find period count, duty count and prescale to suit duty_ns and
+ * period_ns. This is done according to formulas described below:
+ *
+ * period_ns = 10^9 * (PRESCALE + 1) * PC / PWM_CLK_RATE
+ * duty_ns = 10^9 * (PRESCALE + 1) * DC / PWM_CLK_RATE
+ *
+ * PC = (PWM_CLK_RATE * period_ns) / (10^9 * (PRESCALE + 1))
+ * DC = (PWM_CLK_RATE * duty_ns) / (10^9 * (PRESCALE + 1))
+ */
+
+ rate = clk_get_rate(kp->clk);
+
+ while (1) {
+ div = 1000000000;
+ div *= 1 + prescale;
+ val = rate * period_ns;
+ pc = div64_u64(val, div);
+ val = rate * duty_ns;
+ dc = div64_u64(val, div);
+
+ /* If duty_ns or period_ns are not achievable then return */
+ if (pc < PERIOD_COUNT_MIN || dc < DUTY_CYCLE_HIGH_MIN)
+ return -EINVAL;
+
+ /* If pc and dc are in bounds, the calculation is done */
+ if (pc <= PERIOD_COUNT_MAX && dc <= DUTY_CYCLE_HIGH_MAX)
+ break;
+
+ /* Otherwise, increase prescale and recalculate pc and dc */
+ if (++prescale > PRESCALE_MAX)
+ return -EINVAL;
+ }
+
+ /* If the PWM channel is enabled, write the settings to the HW */
+ if (test_bit(PWMF_ENABLED, &pwm->flags)) {
+ value = readl(kp->base + PRESCALE_OFFSET);
+ value &= ~PRESCALE_MASK(chan);
+ value |= prescale << PRESCALE_SHIFT(chan);
+ writel(value, kp->base + PRESCALE_OFFSET);
+
+ writel(pc, kp->base + PERIOD_COUNT_OFFSET(chan));
+
+ writel(dc, kp->base + DUTY_CYCLE_HIGH_OFFSET(chan));
+
+ kona_pwmc_apply_settings(kp, chan);
+ }
+
+ return 0;
+}
+
+static int kona_pwmc_set_polarity(struct pwm_chip *chip, struct pwm_device *pwm,
+ enum pwm_polarity polarity)
+{
+ /* TODO: Add polarity support */
+ if (polarity == PWM_POLARITY_INVERSED)
+ return -EINVAL;
+
+ return 0;
+}
+
+static int kona_pwmc_enable(struct pwm_chip *chip, struct pwm_device *pwm)
+{
+ struct kona_pwmc *kp = to_kona_pwmc(chip);
+ int ret;
+
+ ret = clk_prepare_enable(kp->clk);
+ if (ret < 0) {
+ dev_err(chip->dev, "failed to enable clock: %d\n", ret);
+ return ret;
+ }
+
+ ret = kona_pwmc_config(chip, pwm, pwm->duty_cycle, pwm->period);
+ if (ret < 0) {
+ clk_disable_unprepare(kp->clk);
+ return ret;
+ }
+
+ return 0;
+}
+
+static void kona_pwmc_disable(struct pwm_chip *chip, struct pwm_device *pwm)
+{
+ struct kona_pwmc *kp = to_kona_pwmc(chip);
+ unsigned int chan = pwm->hwpwm;
+
+ /*
+ * The "enable" bits in the control register only affect when settings
+ * start to take effect so the only real way to disable the PWM output
+ * is to program a zero duty cycle.
+ */
+
+ writel(0, kp->base + DUTY_CYCLE_HIGH_OFFSET(chan));
+ kona_pwmc_apply_settings(kp, chan);
+
+ /*
+ * When the PWM clock is disabled, the output is pegged high or low
+ * depending on its state at that instant. To guarantee that the new
+ * settings have taken effect and the output is low a delay of 400ns is
+ * required.
+ */
+
+ ndelay(400);
+
+ clk_disable_unprepare(kp->clk);
+}
+
+static const struct pwm_ops kona_pwm_ops = {
+ .config = kona_pwmc_config,
+ .set_polarity = kona_pwmc_set_polarity,
+ .enable = kona_pwmc_enable,
+ .disable = kona_pwmc_disable,
+ .owner = THIS_MODULE,
+};
+
+static int kona_pwmc_probe(struct platform_device *pdev)
+{
+ struct kona_pwmc *kp;
+ struct resource *res;
+ unsigned int chan;
+ unsigned int value = 0;
+ int ret = 0;
+
+ kp = devm_kzalloc(&pdev->dev, sizeof(*kp), GFP_KERNEL);
+ if (kp == NULL)
+ return -ENOMEM;
+
+ platform_set_drvdata(pdev, kp);
+
+ kp->chip.dev = &pdev->dev;
+ kp->chip.ops = &kona_pwm_ops;
+ kp->chip.base = -1;
+ kp->chip.npwm = 6;
+ kp->chip.of_xlate = of_pwm_xlate_with_flags;
+ kp->chip.of_pwm_n_cells = 3;
+ kp->chip.can_sleep = true;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ kp->base = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(kp->base))
+ return PTR_ERR(kp->base);
+
+ kp->clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(kp->clk)) {
+ dev_err(&pdev->dev, "failed to get clock: %ld\n",
+ PTR_ERR(kp->clk));
+ return PTR_ERR(kp->clk);
+ }
+
+ ret = clk_prepare_enable(kp->clk);
+ if (ret < 0) {
+ dev_err(&pdev->dev, "failed to enable clock: %d\n", ret);
+ return ret;
+ }
+
+ /* Set smooth mode, push/pull, and normal polarity for all channels */
+ for (chan = 0; chan < kp->chip.npwm; chan++) {
+ value |= (1 << PWM_CONTROL_SMOOTH_SHIFT(chan));
+ value |= (1 << PWM_CONTROL_TYPE_SHIFT(chan));
+ value |= (1 << PWM_CONTROL_POLARITY_SHIFT(chan));
+ }
+
+ writel(value, kp->base + PWM_CONTROL_OFFSET);
+
+ clk_disable_unprepare(kp->clk);
+
+ ret = pwmchip_add(&kp->chip);
+ if (ret < 0)
+ dev_err(&pdev->dev, "failed to add PWM chip: %d\n", ret);
+
+ return ret;
+}
+
+static int kona_pwmc_remove(struct platform_device *pdev)
+{
+ struct kona_pwmc *kp = platform_get_drvdata(pdev);
+ unsigned int chan;
+
+ for (chan = 0; chan < kp->chip.npwm; chan++)
+ if (test_bit(PWMF_ENABLED, &kp->chip.pwms[chan].flags))
+ clk_disable_unprepare(kp->clk);
+
+ return pwmchip_remove(&kp->chip);
+}
+
+static const struct of_device_id bcm_kona_pwmc_dt[] = {
+ { .compatible = "brcm,kona-pwm" },
+ { },
+};
+MODULE_DEVICE_TABLE(of, bcm_kona_pwmc_dt);
+
+static struct platform_driver kona_pwmc_driver = {
+ .driver = {
+ .name = "bcm-kona-pwm",
+ .of_match_table = bcm_kona_pwmc_dt,
+ },
+ .probe = kona_pwmc_probe,
+ .remove = kona_pwmc_remove,
+};
+
+module_platform_driver(kona_pwmc_driver);
+MODULE_AUTHOR("Broadcom Corporation <bcm-kernel-feedback-list@broadcom.com>");
+MODULE_AUTHOR("Tim Kryger <tkryger@broadcom.com>");
+MODULE_DESCRIPTION("Broadcom Kona PWM driver");
+MODULE_LICENSE("GPL v2");
--
1.7.0.4
^ permalink raw reply related [flat|nested] 6+ messages in thread