From mboxrd@z Thu Jan 1 00:00:00 1970 From: Ulf Hansson Subject: [PATCH V3 19/19] mmc: mmci: Enforce max frequency configuration through DT Date: Thu, 10 Apr 2014 14:21:02 +0200 Message-ID: <1397132462-8005-20-git-send-email-ulf.hansson@linaro.org> References: <1397132462-8005-1-git-send-email-ulf.hansson@linaro.org> Return-path: In-Reply-To: <1397132462-8005-1-git-send-email-ulf.hansson-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org> Sender: devicetree-owner-u79uwXL29TY76Z2rM5mHXA@public.gmane.org To: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org, Russell King , Linus Walleij Cc: devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, Rob Herring , Ulf Hansson List-Id: devicetree@vger.kernel.org Remove the option to provide a maximum frequency as platform data, enforce it through DT. Signed-off-by: Ulf Hansson --- drivers/mmc/host/mmci.c | 5 +---- include/linux/amba/mmci.h | 4 ---- 2 files changed, 1 insertion(+), 8 deletions(-) diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c index 04cff5e..83f5e56 100644 --- a/drivers/mmc/host/mmci.c +++ b/drivers/mmc/host/mmci.c @@ -1478,13 +1478,10 @@ static int mmci_probe(struct amba_device *dev, * If no maximum operating frequency is supplied, fall back to use * the module parameter, which has a (low) default value in case it * is not specified. Either value must not exceed the clock rate into - * the block, of course. Also note that DT takes precedence over - * platform data. + * the block, of course. */ if (mmc->f_max) mmc->f_max = min(host->mclk, mmc->f_max); - else if (plat->f_max) - mmc->f_max = min(host->mclk, plat->f_max); else mmc->f_max = min(host->mclk, fmax); dev_dbg(mmc_dev(mmc), "clocking block at %u Hz\n", mmc->f_max); diff --git a/include/linux/amba/mmci.h b/include/linux/amba/mmci.h index bf339ff..8c98113 100644 --- a/include/linux/amba/mmci.h +++ b/include/linux/amba/mmci.h @@ -9,9 +9,6 @@ /** * struct mmci_platform_data - platform configuration for the MMCI * (also known as PL180) block. - * @f_max: the maximum operational frequency for this host in this - * platform configuration. When this is specified it takes precedence - * over the module parameter for the same frequency. * @ocr_mask: available voltages on the 4 pins from the block, this * is ignored if a regulator is used, see the MMC_VDD_* masks in * mmc/host.h @@ -28,7 +25,6 @@ * @cd_invert: true if the gpio_cd pin value is active low */ struct mmci_platform_data { - unsigned int f_max; unsigned int ocr_mask; int (*ios_handler)(struct device *, struct mmc_ios *); unsigned int (*status)(struct device *); -- 1.7.9.5 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html