From: Peter Griffin <peter.griffin@linaro.org>
To: peter.griffin@linaro.org, chris@printf.net,
ulf.hansson@linaro.org, maxime.coquelin@st.com,
patrice.chotard@st.com, srinivas.kandagatla@gmail.com
Cc: linux-mmc@vger.kernel.org, devicetree@vger.kernel.org
Subject: [PATCH v2 00/10] Add SDHCI support for STMicroelectronics SoCs
Date: Wed, 4 Jun 2014 17:07:24 +0100 [thread overview]
Message-ID: <1401898054-686-1-git-send-email-peter.griffin@linaro.org> (raw)
This series adds a SDHCI platform driver for ST SoCs, along with
the additional device tree bindings and configuration to enable
the controller to work properly.
Initially it supports the stih416 and stih415 SoCs, and has
been tested on a stih416-b2020 board.
regards,
Peter.
Changes since v1
- Whitespace cleanups
- Use readl_relaxed io accessor
- Add update to MAINTAINERS
- Remove reset controller code from platform driver
- Remove #ifdef around sleep ops
- Use sdhci_pltfm_clk_get_max_clock lib function
- Pass bus-width etc through board device tree node
- Remove unncessary header
- Remove / change some debug messages
- Remove final break from switch case
Peter Griffin (10):
mmc: sdhci-st: Intial support for ST SDHCI controller
mmc: sdhci-st: ST Microelectronics SDHCI binding documentation.
ARM: STi: DT: Add sdhci pins for stih416
ARM: STi: DT: Add sdhci controller for stih416
ARM: STi: DT: Add sdhci pin configuration for stih415
ARM: STi: DT: Add sdhci controller for stih415
ARM: STi: DT: Enable mmc0 for both stih415 and stih416 SoCs
ARM: STi: DT: Enable second sdhci controller for stih416 b2020 boards.
ARM: update multi_v7_defconfig for STI
MAINTAINERS: Add sdhci-st file to ARCH/STI architecture
Documentation/devicetree/bindings/mmc/sdhci-st.txt | 33 ++++
MAINTAINERS | 1 +
arch/arm/boot/dts/stih415-pinctrl.dtsi | 21 +++
arch/arm/boot/dts/stih415.dtsi | 12 ++
arch/arm/boot/dts/stih416-b2020-revE.dts | 6 +
arch/arm/boot/dts/stih416-b2020.dts | 8 +
arch/arm/boot/dts/stih416-pinctrl.dtsi | 39 ++++
arch/arm/boot/dts/stih416.dtsi | 24 +++
arch/arm/boot/dts/stih41x-b2020.dtsi | 4 +
arch/arm/boot/dts/stih41x-b2020x.dtsi | 4 +
arch/arm/configs/multi_v7_defconfig | 1 +
drivers/mmc/host/Kconfig | 12 ++
drivers/mmc/host/Makefile | 1 +
drivers/mmc/host/sdhci-st.c | 201 +++++++++++++++++++++
14 files changed, 367 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mmc/sdhci-st.txt
create mode 100644 drivers/mmc/host/sdhci-st.c
--
1.9.1
next reply other threads:[~2014-06-04 16:07 UTC|newest]
Thread overview: 15+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-06-04 16:07 Peter Griffin [this message]
2014-06-04 16:07 ` [PATCH v2 01/10] mmc: sdhci-st: Intial support for ST SDHCI controller Peter Griffin
2014-06-04 16:07 ` [PATCH v2 02/10] mmc: sdhci-st: ST Microelectronics SDHCI binding documentation Peter Griffin
2014-06-04 16:07 ` [PATCH v2 03/10] ARM: STi: DT: Add sdhci pins for stih416 Peter Griffin
2014-06-04 16:07 ` [PATCH v2 04/10] ARM: STi: DT: Add sdhci controller " Peter Griffin
2014-06-04 16:07 ` [PATCH v2 05/10] ARM: STi: DT: Add sdhci pin configuration for stih415 Peter Griffin
2014-06-04 16:07 ` [PATCH v2 07/10] ARM: STi: DT: Enable mmc0 for both stih415 and stih416 SoCs Peter Griffin
2014-06-04 16:07 ` [PATCH v2 08/10] ARM: STi: DT: Enable second sdhci controller for stih416 b2020 boards Peter Griffin
2014-07-09 10:09 ` Ulf Hansson
2014-07-09 10:30 ` Peter Griffin
2014-07-09 11:00 ` Maxime Coquelin
2014-07-09 12:17 ` Ulf Hansson
[not found] ` <1401898054-686-1-git-send-email-peter.griffin-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
2014-06-04 16:07 ` [PATCH v2 06/10] ARM: STi: DT: Add sdhci controller for stih415 Peter Griffin
2014-06-04 16:07 ` [PATCH v2 09/10] ARM: update multi_v7_defconfig for STI Peter Griffin
2014-06-04 16:07 ` [PATCH v2 10/10] MAINTAINERS: Add sdhci-st file to ARCH/STI architecture Peter Griffin
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1401898054-686-1-git-send-email-peter.griffin@linaro.org \
--to=peter.griffin@linaro.org \
--cc=chris@printf.net \
--cc=devicetree@vger.kernel.org \
--cc=linux-mmc@vger.kernel.org \
--cc=maxime.coquelin@st.com \
--cc=patrice.chotard@st.com \
--cc=srinivas.kandagatla@gmail.com \
--cc=ulf.hansson@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).