From: Peter Griffin <peter.griffin@linaro.org>
To: linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, ulf.hansson@linaro.org,
chris@printf.net, maxime.coquelin@st.com, patrice.chotard@st.com,
srinivas.kandagatla@gmail.com
Cc: peter.griffin@linaro.org, lee.jones@linaro.org,
linux-mmc@vger.kernel.org, devicetree@vger.kernel.org,
peppe.cavallaro@st.com
Subject: [PATCH v4 01/10] mmc: sdhci-st: Intial support for ST SDHCI controller
Date: Wed, 9 Jul 2014 16:07:32 +0100 [thread overview]
Message-ID: <1404918461-25390-2-git-send-email-peter.griffin@linaro.org> (raw)
In-Reply-To: <1404918461-25390-1-git-send-email-peter.griffin@linaro.org>
This platform driver adds initial support for the SDHCI host controller
found on STMicroelectronics SoCs.
It has been tested on STiH41x b2020 platforms currently.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
---
drivers/mmc/host/Kconfig | 12 +++
drivers/mmc/host/Makefile | 1 +
drivers/mmc/host/sdhci-st.c | 176 ++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 189 insertions(+)
create mode 100644 drivers/mmc/host/sdhci-st.c
diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig
index a565254..6615b79 100644
--- a/drivers/mmc/host/Kconfig
+++ b/drivers/mmc/host/Kconfig
@@ -290,6 +290,18 @@ config MMC_MOXART
be found on some embedded hardware such as UC-7112-LX.
If you have a controller with this interface, say Y here.
+config MMC_SDHCI_ST
+ tristate "SDHCI support on STMicroelectronics SoC"
+ depends on ARCH_STI
+ depends on MMC_SDHCI_PLTFM
+ select MMC_SDHCI_IO_ACCESSORS
+ help
+ This selects the Secure Digital Host Controller Interface in
+ STMicroelectronics SoCs.
+
+ If you have a controller with this interface, say Y or M here.
+ If unsure, say N.
+
config MMC_OMAP
tristate "TI OMAP Multimedia Card Interface support"
depends on ARCH_OMAP
diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile
index 7f81ddf..f211eed 100644
--- a/drivers/mmc/host/Makefile
+++ b/drivers/mmc/host/Makefile
@@ -68,6 +68,7 @@ obj-$(CONFIG_MMC_SDHCI_OF_HLWD) += sdhci-of-hlwd.o
obj-$(CONFIG_MMC_SDHCI_BCM_KONA) += sdhci-bcm-kona.o
obj-$(CONFIG_MMC_SDHCI_BCM2835) += sdhci-bcm2835.o
obj-$(CONFIG_MMC_SDHCI_MSM) += sdhci-msm.o
+obj-$(CONFIG_MMC_SDHCI_ST) += sdhci-st.o
ifeq ($(CONFIG_CB710_DEBUG),y)
CFLAGS-cb710-mmc += -DDEBUG
diff --git a/drivers/mmc/host/sdhci-st.c b/drivers/mmc/host/sdhci-st.c
new file mode 100644
index 0000000..328f348
--- /dev/null
+++ b/drivers/mmc/host/sdhci-st.c
@@ -0,0 +1,176 @@
+/*
+ * Support for SDHCI on STMicroelectronics SoCs
+ *
+ * Copyright (C) 2014 STMicroelectronics Ltd
+ * Author: Giuseppe Cavallaro <peppe.cavallaro@st.com>
+ * Contributors: Peter Griffin <peter.griffin@linaro.org>
+ *
+ * Based on sdhci-cns3xxx.c
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/module.h>
+#include <linux/err.h>
+#include <linux/mmc/host.h>
+
+#include "sdhci-pltfm.h"
+
+static u32 sdhci_st_readl(struct sdhci_host *host, int reg)
+{
+ u32 ret;
+
+ switch (reg) {
+ case SDHCI_CAPABILITIES:
+ ret = readl_relaxed(host->ioaddr + reg);
+ /* Support 3.3V and 1.8V */
+ ret &= ~SDHCI_CAN_VDD_300;
+ break;
+ default:
+ ret = readl_relaxed(host->ioaddr + reg);
+ }
+ return ret;
+}
+
+static const struct sdhci_ops sdhci_st_ops = {
+ .get_max_clock = sdhci_pltfm_clk_get_max_clock,
+ .set_clock = sdhci_set_clock,
+ .set_bus_width = sdhci_set_bus_width,
+ .read_l = sdhci_st_readl,
+ .reset = sdhci_reset,
+};
+
+static const struct sdhci_pltfm_data sdhci_st_pdata = {
+ .ops = &sdhci_st_ops,
+ .quirks = SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC |
+ SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN,
+};
+
+
+static int sdhci_st_probe(struct platform_device *pdev)
+{
+ struct sdhci_host *host;
+ struct sdhci_pltfm_host *pltfm_host;
+ struct clk *clk;
+ int ret = 0;
+ u16 host_version;
+
+ clk = devm_clk_get(&pdev->dev, "mmc");
+ if (IS_ERR(clk)) {
+ dev_err(&pdev->dev, "Peripheral clk not found\n");
+ return PTR_ERR(clk);
+ }
+
+ host = sdhci_pltfm_init(pdev, &sdhci_st_pdata, 0);
+ if (IS_ERR(host)) {
+ dev_err(&pdev->dev, "Failed sdhci_pltfm_init\n");
+ return PTR_ERR(host);
+ }
+
+ ret = mmc_of_parse(host->mmc);
+
+ if (ret) {
+ dev_err(&pdev->dev, "Failed mmc_of_parse\n");
+ return ret;
+ }
+
+ clk_prepare_enable(clk);
+
+ pltfm_host = sdhci_priv(host);
+ pltfm_host->clk = clk;
+
+ ret = sdhci_add_host(host);
+ if (ret) {
+ dev_err(&pdev->dev, "Failed sdhci_add_host\n");
+ goto err_out;
+ }
+
+ platform_set_drvdata(pdev, host);
+
+ host_version = readw_relaxed((host->ioaddr + SDHCI_HOST_VERSION));
+
+ dev_info(&pdev->dev, "SDHCI ST Initialised: Host Version: 0x%x Vendor Version 0x%x\n",
+ ((host_version & SDHCI_SPEC_VER_MASK) >> SDHCI_SPEC_VER_SHIFT),
+ ((host_version & SDHCI_VENDOR_VER_MASK) >>
+ SDHCI_VENDOR_VER_SHIFT));
+
+ return 0;
+
+err_out:
+ clk_disable_unprepare(clk);
+ sdhci_pltfm_free(pdev);
+
+ return ret;
+}
+
+static int sdhci_st_remove(struct platform_device *pdev)
+{
+ struct sdhci_host *host = platform_get_drvdata(pdev);
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+
+ clk_disable_unprepare(pltfm_host->clk);
+
+ return sdhci_pltfm_unregister(pdev);
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int sdhci_st_suspend(struct device *dev)
+{
+ struct sdhci_host *host = dev_get_drvdata(dev);
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ int ret = sdhci_suspend_host(host);
+
+ if (ret)
+ goto out;
+
+ clk_disable_unprepare(pltfm_host->clk);
+out:
+ return ret;
+}
+
+static int sdhci_st_resume(struct device *dev)
+{
+ struct sdhci_host *host = dev_get_drvdata(dev);
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+
+ clk_prepare_enable(pltfm_host->clk);
+
+ return sdhci_resume_host(host);
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(sdhci_st_pmops, sdhci_st_suspend, sdhci_st_resume);
+
+static const struct of_device_id st_sdhci_match[] = {
+ { .compatible = "st,sdhci" },
+ {},
+};
+
+MODULE_DEVICE_TABLE(of, st_sdhci_match);
+
+static struct platform_driver sdhci_st_driver = {
+ .probe = sdhci_st_probe,
+ .remove = sdhci_st_remove,
+ .driver = {
+ .name = "sdhci-st",
+ .pm = &sdhci_st_pmops,
+ .of_match_table = of_match_ptr(st_sdhci_match),
+ },
+};
+
+module_platform_driver(sdhci_st_driver);
+
+MODULE_DESCRIPTION("SDHCI driver for STMicroelectronics SoCs");
+MODULE_AUTHOR("Giuseppe Cavallaro <peppe.cavallaro@st.com>");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:st-sdhci");
--
1.9.1
next prev parent reply other threads:[~2014-07-09 15:07 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-07-09 15:07 [PATCH v4 00/10] Add SDHCI support for ST Microelectronics SoCs Peter Griffin
2014-07-09 15:07 ` Peter Griffin [this message]
[not found] ` <1404918461-25390-2-git-send-email-peter.griffin-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
2014-07-10 7:12 ` [PATCH v4 01/10] mmc: sdhci-st: Intial support for ST SDHCI controller Ulf Hansson
2014-07-09 15:07 ` [PATCH v4 02/10] mmc: sdhci-st: ST Microelectronics SDHCI binding documentation Peter Griffin
2014-07-10 7:13 ` Ulf Hansson
2014-07-09 15:07 ` [PATCH v4 03/10] ARM: STi: DT: Add sdhci pins for stih416 Peter Griffin
2014-07-09 15:07 ` [PATCH v4 04/10] ARM: STi: DT: Add sdhci controller " Peter Griffin
2014-07-09 15:07 ` [PATCH v4 05/10] ARM: STi: DT: Add sdhci pin configuration for stih415 Peter Griffin
2014-07-09 15:07 ` [PATCH v4 06/10] ARM: STi: DT: Add sdhci controller " Peter Griffin
2014-07-09 15:07 ` [PATCH v4 07/10] ARM: STi: DT: Enable mmc0 for both stih415 and stih416 SoCs Peter Griffin
[not found] ` <1404918461-25390-1-git-send-email-peter.griffin-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
2014-07-09 15:07 ` [PATCH v4 08/10] ARM: STi: DT: Enable second sdhci controller for stih416 b2020 boards Peter Griffin
2014-07-09 15:07 ` [PATCH v4 09/10] ARM: update multi_v7_defconfig for STI Peter Griffin
2014-07-21 9:49 ` Maxime Coquelin
2014-07-09 15:07 ` [PATCH v4 10/10] MAINTAINERS: Add sdhci-st file to ARCH/STI architecture Peter Griffin
2014-07-09 15:51 ` [PATCH v4 00/10] Add SDHCI support for ST Microelectronics SoCs Maxime Coquelin
2014-07-10 12:51 ` Ulf Hansson
2014-07-10 12:57 ` Maxime Coquelin
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1404918461-25390-2-git-send-email-peter.griffin@linaro.org \
--to=peter.griffin@linaro.org \
--cc=chris@printf.net \
--cc=devicetree@vger.kernel.org \
--cc=lee.jones@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mmc@vger.kernel.org \
--cc=maxime.coquelin@st.com \
--cc=patrice.chotard@st.com \
--cc=peppe.cavallaro@st.com \
--cc=srinivas.kandagatla@gmail.com \
--cc=ulf.hansson@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).