From: Marek Belisko <marek@goldelico.com>
To: bcousson@baylibre.com, tony@atomide.com
Cc: robh+dt@kernel.org, pawel.moll@arm.com, mark.rutland@arm.com,
ijc+devicetree@hellion.org.uk, galak@codeaurora.org,
linux@arm.linux.org.uk, linux-omap@vger.kernel.org,
devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, hns@goldelico.com,
Marek Belisko <marek@goldelico.com>
Subject: [PATCH 5/7] arm: dts: omap3-gta04: Add USB host support
Date: Mon, 21 Jul 2014 23:05:25 +0200 [thread overview]
Message-ID: <1405976727-15166-6-git-send-email-marek@goldelico.com> (raw)
In-Reply-To: <1405976727-15166-1-git-send-email-marek@goldelico.com>
Signed-off-by: Marek Belisko <marek@goldelico.com>
---
arch/arm/boot/dts/omap3-gta04.dts | 45 +++++++++++++++++++++++++++++++++++++++
1 file changed, 45 insertions(+)
diff --git a/arch/arm/boot/dts/omap3-gta04.dts b/arch/arm/boot/dts/omap3-gta04.dts
index 4ca1277..370c08b 100644
--- a/arch/arm/boot/dts/omap3-gta04.dts
+++ b/arch/arm/boot/dts/omap3-gta04.dts
@@ -74,9 +74,30 @@
};
};
};
+
+ hsusb2_phy: hsusb2_phy {
+ compatible = "usb-nop-xceiv";
+ reset-gpios = <&gpio6 14 GPIO_ACTIVE_LOW>;
+ };
};
&omap3_pmx_core {
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ &hsusb2_pins
+ >;
+
+ hsusb2_pins: pinmux_hsusb2_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi1_cs3.hsusb2_data2 */
+ OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_clk.hsusb2_data7 */
+ OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_simo.hsusb2_data4 */
+ OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_somi.hsusb2_data5 */
+ OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs0.hsusb2_data6 */
+ OMAP3_CORE1_IOPAD(0x21de, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs1.hsusb2_data3 */
+ >;
+ };
+
uart1_pins: pinmux_uart1_pins {
pinctrl-single,pins = <
0x152 (PIN_INPUT | MUX_MODE0) /* uart1_rx.uart1_rx */
@@ -144,6 +165,22 @@
};
&omap3_pmx_core2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ &hsusb2_2_pins
+ >;
+
+ hsusb2_2_pins: pinmux_hsusb2_2_pins {
+ pinctrl-single,pins = <
+ OMAP3630_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3) /* etk_d10.hsusb2_clk */
+ OMAP3630_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3) /* etk_d11.hsusb2_stp */
+ OMAP3630_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d12.hsusb2_dir */
+ OMAP3630_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d13.hsusb2_nxt */
+ OMAP3630_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d14.hsusb2_data0 */
+ OMAP3630_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d15.hsusb2_data1 */
+ >;
+ };
+
spi_gpio_pins: spi_gpio_pinmux {
pinctrl-single,pins = <
OMAP3630_CORE2_IOPAD(0x25d8, PIN_OUTPUT | MUX_MODE4) /* clk */
@@ -259,6 +296,14 @@
power = <50>;
};
+&usbhshost {
+ port2-mode = "ehci-phy";
+};
+
+&usbhsehci {
+ phys = <0 &hsusb2_phy>;
+};
+
&mmc1 {
pinctrl-names = "default";
pinctrl-0 = <&mmc1_pins>;
--
1.9.1
next prev parent reply other threads:[~2014-07-21 21:05 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-07-21 21:05 [PATCH 0/7] arm: dts: oma3-gta04: Various updates Marek Belisko
2014-07-21 21:05 ` [PATCH 1/7] arm: dts: omap3-gta04: Add nand support Marek Belisko
[not found] ` <1405976727-15166-2-git-send-email-marek-xXXSsgcRVICgSpxsJD1C4w@public.gmane.org>
2014-07-22 6:24 ` Tony Lindgren
[not found] ` <20140722062442.GF18374-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org>
2014-07-22 9:00 ` Belisko Marek
2014-07-21 21:05 ` [PATCH 2/7] arm: dts: omap3-gta04: Fix magnetometer model Marek Belisko
2014-07-21 21:05 ` [PATCH 3/7] arm: dts: omap3-gta04: Add wifi reset node Marek Belisko
2014-07-21 21:05 ` [PATCH 4/7] arm: dts: omap3-gta04: Move spi gpio pins to pmx_core2 Marek Belisko
2014-07-21 21:05 ` Marek Belisko [this message]
[not found] ` <1405976727-15166-1-git-send-email-marek-xXXSsgcRVICgSpxsJD1C4w@public.gmane.org>
2014-07-21 21:05 ` [PATCH 6/7] arm: dts: omap3-gta04: Add display alias Marek Belisko
2014-07-21 21:05 ` [PATCH 7/7] arm: dts: omap3-gta04: Add twl4030 regulators parameters Marek Belisko
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1405976727-15166-6-git-send-email-marek@goldelico.com \
--to=marek@goldelico.com \
--cc=bcousson@baylibre.com \
--cc=devicetree@vger.kernel.org \
--cc=galak@codeaurora.org \
--cc=hns@goldelico.com \
--cc=ijc+devicetree@hellion.org.uk \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-omap@vger.kernel.org \
--cc=linux@arm.linux.org.uk \
--cc=mark.rutland@arm.com \
--cc=pawel.moll@arm.com \
--cc=robh+dt@kernel.org \
--cc=tony@atomide.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).