From: Chao Xie <chao.xie@marvell.com>
To: haojian.zhuang@gmail.com, haojian.zhuang@linaro.org,
mturquette@linaro.org, chao.xie@marvell.com,
xiechao_mail@163.com, linux-arm-kernel@lists.infradead.org,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: [PATCH 01/12] clk: mmp: add prefix "mmp" for structures defined for clk-frac
Date: Tue, 26 Aug 2014 12:38:13 +0800 [thread overview]
Message-ID: <1409027904-21859-2-git-send-email-chao.xie@marvell.com> (raw)
In-Reply-To: <1409027904-21859-1-git-send-email-chao.xie@marvell.com>
From: Chao Xie <chao.xie@marvell.com>
The structures defined for clk-frac will be used out side
of clk-frac.c.
To avoid conflicts, add prefix "mmp" for these structures'
name.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
---
drivers/clk/mmp/clk-frac.c | 23 ++++++++++++-----------
drivers/clk/mmp/clk-mmp2.c | 4 ++--
drivers/clk/mmp/clk-pxa168.c | 4 ++--
drivers/clk/mmp/clk-pxa910.c | 4 ++--
drivers/clk/mmp/clk.h | 8 ++++----
5 files changed, 22 insertions(+), 21 deletions(-)
diff --git a/drivers/clk/mmp/clk-frac.c b/drivers/clk/mmp/clk-frac.c
index 23a56f5..3fbc9ca 100644
--- a/drivers/clk/mmp/clk-frac.c
+++ b/drivers/clk/mmp/clk-frac.c
@@ -22,19 +22,19 @@
* numerator/denominator = Fin / (Fout * factor)
*/
-#define to_clk_factor(hw) container_of(hw, struct clk_factor, hw)
-struct clk_factor {
+#define to_clk_factor(hw) container_of(hw, struct mmp_clk_factor, hw)
+struct mmp_clk_factor {
struct clk_hw hw;
void __iomem *base;
- struct clk_factor_masks *masks;
- struct clk_factor_tbl *ftbl;
+ struct mmp_clk_factor_masks *masks;
+ struct mmp_clk_factor_tbl *ftbl;
unsigned int ftbl_cnt;
};
static long clk_factor_round_rate(struct clk_hw *hw, unsigned long drate,
unsigned long *prate)
{
- struct clk_factor *factor = to_clk_factor(hw);
+ struct mmp_clk_factor *factor = to_clk_factor(hw);
unsigned long rate = 0, prev_rate;
int i;
@@ -58,8 +58,8 @@ static long clk_factor_round_rate(struct clk_hw *hw, unsigned long drate,
static unsigned long clk_factor_recalc_rate(struct clk_hw *hw,
unsigned long parent_rate)
{
- struct clk_factor *factor = to_clk_factor(hw);
- struct clk_factor_masks *masks = factor->masks;
+ struct mmp_clk_factor *factor = to_clk_factor(hw);
+ struct mmp_clk_factor_masks *masks = factor->masks;
unsigned int val, num, den;
val = readl_relaxed(factor->base);
@@ -81,8 +81,8 @@ static unsigned long clk_factor_recalc_rate(struct clk_hw *hw,
static int clk_factor_set_rate(struct clk_hw *hw, unsigned long drate,
unsigned long prate)
{
- struct clk_factor *factor = to_clk_factor(hw);
- struct clk_factor_masks *masks = factor->masks;
+ struct mmp_clk_factor *factor = to_clk_factor(hw);
+ struct mmp_clk_factor_masks *masks = factor->masks;
int i;
unsigned long val;
unsigned long prev_rate, rate = 0;
@@ -118,10 +118,11 @@ static struct clk_ops clk_factor_ops = {
struct clk *mmp_clk_register_factor(const char *name, const char *parent_name,
unsigned long flags, void __iomem *base,
- struct clk_factor_masks *masks, struct clk_factor_tbl *ftbl,
+ struct mmp_clk_factor_masks *masks,
+ struct mmp_clk_factor_tbl *ftbl,
unsigned int ftbl_cnt)
{
- struct clk_factor *factor;
+ struct mmp_clk_factor *factor;
struct clk_init_data init;
struct clk *clk;
diff --git a/drivers/clk/mmp/clk-mmp2.c b/drivers/clk/mmp/clk-mmp2.c
index b2721ca..7083f12 100644
--- a/drivers/clk/mmp/clk-mmp2.c
+++ b/drivers/clk/mmp/clk-mmp2.c
@@ -54,7 +54,7 @@
static DEFINE_SPINLOCK(clk_lock);
-static struct clk_factor_masks uart_factor_masks = {
+static struct mmp_clk_factor_masks uart_factor_masks = {
.factor = 2,
.num_mask = 0x1fff,
.den_mask = 0x1fff,
@@ -62,7 +62,7 @@ static struct clk_factor_masks uart_factor_masks = {
.den_shift = 0,
};
-static struct clk_factor_tbl uart_factor_tbl[] = {
+static struct mmp_clk_factor_tbl uart_factor_tbl[] = {
{.num = 14634, .den = 2165}, /*14.745MHZ */
{.num = 3521, .den = 689}, /*19.23MHZ */
{.num = 9679, .den = 5728}, /*58.9824MHZ */
diff --git a/drivers/clk/mmp/clk-pxa168.c b/drivers/clk/mmp/clk-pxa168.c
index 014396b..75266ac 100644
--- a/drivers/clk/mmp/clk-pxa168.c
+++ b/drivers/clk/mmp/clk-pxa168.c
@@ -47,7 +47,7 @@
static DEFINE_SPINLOCK(clk_lock);
-static struct clk_factor_masks uart_factor_masks = {
+static struct mmp_clk_factor_masks uart_factor_masks = {
.factor = 2,
.num_mask = 0x1fff,
.den_mask = 0x1fff,
@@ -55,7 +55,7 @@ static struct clk_factor_masks uart_factor_masks = {
.den_shift = 0,
};
-static struct clk_factor_tbl uart_factor_tbl[] = {
+static struct mmp_clk_factor_tbl uart_factor_tbl[] = {
{.num = 8125, .den = 1536}, /*14.745MHZ */
};
diff --git a/drivers/clk/mmp/clk-pxa910.c b/drivers/clk/mmp/clk-pxa910.c
index 9efc6a4..f817999 100644
--- a/drivers/clk/mmp/clk-pxa910.c
+++ b/drivers/clk/mmp/clk-pxa910.c
@@ -45,7 +45,7 @@
static DEFINE_SPINLOCK(clk_lock);
-static struct clk_factor_masks uart_factor_masks = {
+static struct mmp_clk_factor_masks uart_factor_masks = {
.factor = 2,
.num_mask = 0x1fff,
.den_mask = 0x1fff,
@@ -53,7 +53,7 @@ static struct clk_factor_masks uart_factor_masks = {
.den_shift = 0,
};
-static struct clk_factor_tbl uart_factor_tbl[] = {
+static struct mmp_clk_factor_tbl uart_factor_tbl[] = {
{.num = 8125, .den = 1536}, /*14.745MHZ */
};
diff --git a/drivers/clk/mmp/clk.h b/drivers/clk/mmp/clk.h
index ab86dd4..3fe92be 100644
--- a/drivers/clk/mmp/clk.h
+++ b/drivers/clk/mmp/clk.h
@@ -7,7 +7,7 @@
#define APBC_NO_BUS_CTRL BIT(0)
#define APBC_POWER_CTRL BIT(1)
-struct clk_factor_masks {
+struct mmp_clk_factor_masks {
unsigned int factor;
unsigned int num_mask;
unsigned int den_mask;
@@ -15,7 +15,7 @@ struct clk_factor_masks {
unsigned int den_shift;
};
-struct clk_factor_tbl {
+struct mmp_clk_factor_tbl {
unsigned int num;
unsigned int den;
};
@@ -30,6 +30,6 @@ extern struct clk *mmp_clk_register_apmu(const char *name,
spinlock_t *lock);
extern struct clk *mmp_clk_register_factor(const char *name,
const char *parent_name, unsigned long flags,
- void __iomem *base, struct clk_factor_masks *masks,
- struct clk_factor_tbl *ftbl, unsigned int ftbl_cnt);
+ void __iomem *base, struct mmp_clk_factor_masks *masks,
+ struct mmp_clk_factor_tbl *ftbl, unsigned int ftbl_cnt);
#endif
--
1.8.3.2
next prev parent reply other threads:[~2014-08-26 4:38 UTC|newest]
Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-08-26 4:38 [PATCH 00/12] clk: mmp: clock device tree support Chao Xie
2014-08-26 4:38 ` Chao Xie [this message]
2014-08-26 4:38 ` [PATCH 02/12] clk: mmp: add spin lock for clk-frac Chao Xie
2014-09-03 18:04 ` Mike Turquette
2014-09-10 1:30 ` Chao Xie
2014-08-26 4:38 ` [PATCH 03/12] clk: mmp: add init callback " Chao Xie
2014-08-26 4:38 ` [PATCH 05/12] clk: mmp: add clock type mix Chao Xie
2014-08-26 4:38 ` [PATCH 06/12] clk: mmp: add mmp private gate clock Chao Xie
2014-09-03 17:55 ` Mike Turquette
2014-09-04 4:02 ` Chao Xie
[not found] ` <479e7ccf.16dee.1483ed3a882.Coremail.xiechao_mail-9Onoh4P/yGk@public.gmane.org>
2014-09-04 4:16 ` Chen-Yu Tsai
2014-08-26 4:38 ` [PATCH 07/12] clk: mmp: add basic support functions for DT support Chao Xie
2014-08-26 4:38 ` [PATCH 08/12] clk: mmp: add pxa168 DT support for clock driver Chao Xie
2014-08-26 4:38 ` [PATCH 09/12] clk: mmp: add pxa910 " Chao Xie
2014-08-26 4:38 ` [PATCH 10/12] clk: mmp: add mmp2 " Chao Xie
2014-08-26 4:38 ` [PATCH 11/12] arm: mmp: Make all the dts file to be compiled by Makefile Chao Xie
2014-08-26 4:38 ` [PATCH 12/12] arm: mmp: Make use of the DT supported clock Chao Xie
[not found] ` <1409027904-21859-1-git-send-email-chao.xie-eYqpPyKDWXRBDgjK7y7TUQ@public.gmane.org>
2014-08-26 4:38 ` [PATCH 04/12] clk: mmp: move definiton of mmp_clk_frac to clk.h Chao Xie
2014-08-26 4:55 ` [PATCH 00/12] clk: mmp: clock device tree support Haojian Zhuang
-- strict thread matches above, loose matches on Subject: below --
2014-06-10 1:27 Chao Xie
2014-06-10 1:27 ` [PATCH 01/12] clk: mmp: add prefix "mmp" for structures defined for clk-frac Chao Xie
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1409027904-21859-2-git-send-email-chao.xie@marvell.com \
--to=chao.xie@marvell.com \
--cc=devicetree@vger.kernel.org \
--cc=haojian.zhuang@gmail.com \
--cc=haojian.zhuang@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mturquette@linaro.org \
--cc=xiechao_mail@163.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).