[parent not found: <1412773376-25212-1-git-send-email-wens-jdAy2FN1RRM@public.gmane.org>]
* [PATCH v3 1/5] ARM: sunxi: Introduce Allwinner A80 support
[not found] ` <1412773376-25212-1-git-send-email-wens-jdAy2FN1RRM@public.gmane.org>
@ 2014-10-08 13:02 ` Chen-Yu Tsai
0 siblings, 0 replies; 13+ messages in thread
From: Chen-Yu Tsai @ 2014-10-08 13:02 UTC (permalink / raw)
To: Maxime Ripard, Rob Herring, Pawel Moll, Mark Rutland,
Ian Campbell, Kumar Gala
Cc: Chen-Yu Tsai, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA, Shuge, Meng Zhang,
Gregory CLEMENT
The Allwinner A80 is a new Cortex octo-core A7/A15 big.LITTLE SoC.
While it's processor cores and interconnecting bus are new, it
re-uses many peripherals found in earlier Allwinner SoCs.
Signed-off-by: Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
---
arch/arm/mach-sunxi/Kconfig | 5 +++++
arch/arm/mach-sunxi/sunxi.c | 9 +++++++++
2 files changed, 14 insertions(+)
diff --git a/arch/arm/mach-sunxi/Kconfig b/arch/arm/mach-sunxi/Kconfig
index 1aaa1e1..d04f84b 100644
--- a/arch/arm/mach-sunxi/Kconfig
+++ b/arch/arm/mach-sunxi/Kconfig
@@ -42,4 +42,9 @@ config MACH_SUN8I
select MFD_SUN6I_PRCM
select RESET_CONTROLLER
+config MACH_SUN9I
+ bool "Allwinner (sun9i) SoCs support"
+ default ARCH_SUNXI
+ select ARM_GIC
+
endif
diff --git a/arch/arm/mach-sunxi/sunxi.c b/arch/arm/mach-sunxi/sunxi.c
index 42d4753..ba926b5 100644
--- a/arch/arm/mach-sunxi/sunxi.c
+++ b/arch/arm/mach-sunxi/sunxi.c
@@ -139,3 +139,12 @@ static const char * const sun8i_board_dt_compat[] = {
DT_MACHINE_START(SUN8I_DT, "Allwinner sun8i (A23) Family")
.dt_compat = sun8i_board_dt_compat,
MACHINE_END
+
+static const char * const sun9i_board_dt_compat[] = {
+ "allwinner,sun9i-a80",
+ NULL,
+};
+
+DT_MACHINE_START(SUN9I_DT, "Allwinner sun9i Family")
+ .dt_compat = sun9i_board_dt_compat,
+MACHINE_END
--
2.1.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [PATCH v3 2/5] ARM: dts: sunxi: Add Allwinner A80 dtsi
2014-10-08 13:02 [PATCH v3 0/5] ARM: sunxi: Add basic support for Allwinner A80 SoC Chen-Yu Tsai
[not found] ` <1412773376-25212-1-git-send-email-wens-jdAy2FN1RRM@public.gmane.org>
@ 2014-10-08 13:02 ` Chen-Yu Tsai
[not found] ` <1412773376-25212-3-git-send-email-wens-jdAy2FN1RRM@public.gmane.org>
2014-10-08 13:02 ` [PATCH v3 3/5] ARM: dts: sun9i: Add A80 Optimus Board support Chen-Yu Tsai
` (4 subsequent siblings)
6 siblings, 1 reply; 13+ messages in thread
From: Chen-Yu Tsai @ 2014-10-08 13:02 UTC (permalink / raw)
To: Maxime Ripard, Rob Herring, Pawel Moll, Mark Rutland,
Ian Campbell, Kumar Gala
Cc: Chen-Yu Tsai, linux-arm-kernel, devicetree, linux-kernel, Shuge,
Meng Zhang, Gregory CLEMENT
The Allwinner A80 is a new multi-purpose SoC with 4 Cortex-A7 and
4 Cortex-A15 cores in a big.LITTLE architecture, and a 64-core
PowerVR G6230 GPU.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
arch/arm/boot/dts/sun9i-a80.dtsi | 257 +++++++++++++++++++++++++++++++++++++++
1 file changed, 257 insertions(+)
create mode 100644 arch/arm/boot/dts/sun9i-a80.dtsi
diff --git a/arch/arm/boot/dts/sun9i-a80.dtsi b/arch/arm/boot/dts/sun9i-a80.dtsi
new file mode 100644
index 0000000..5e2ec4b
--- /dev/null
+++ b/arch/arm/boot/dts/sun9i-a80.dtsi
@@ -0,0 +1,257 @@
+/*
+ * Copyright 2014 Chen-Yu Tsai
+ *
+ * Chen-Yu Tsai <wens@csie.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this library; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/include/ "skeleton64.dtsi"
+
+/ {
+ interrupt-parent = <&gic>;
+
+ aliases {
+ serial0 = &uart0;
+ serial1 = &uart1;
+ serial2 = &uart2;
+ serial3 = &uart3;
+ serial4 = &uart4;
+ serial5 = &uart5;
+ serial6 = &r_uart;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@0 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <0x0>;
+ };
+
+ cpu1: cpu@1 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <0x1>;
+ };
+
+ cpu2: cpu@2 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <0x2>;
+ };
+
+ cpu3: cpu@3 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <0x3>;
+ };
+
+ cpu4: cpu@100 {
+ compatible = "arm,cortex-a15";
+ device_type = "cpu";
+ reg = <0x100>;
+ };
+
+ cpu5: cpu@101 {
+ compatible = "arm,cortex-a15";
+ device_type = "cpu";
+ reg = <0x101>;
+ };
+
+ cpu6: cpu@102 {
+ compatible = "arm,cortex-a15";
+ device_type = "cpu";
+ reg = <0x102>;
+ };
+
+ cpu7: cpu@103 {
+ compatible = "arm,cortex-a15";
+ device_type = "cpu";
+ reg = <0x103>;
+ };
+ };
+
+ memory {
+ /* 8GB max. with LPAE */
+ reg = <0 0x20000000 0x02 0>;
+ };
+
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ /*
+ * map 64 bit address range down to 32 bits,
+ * as the peripherals are all under 512MB.
+ */
+ ranges = <0 0 0 0x20000000>;
+
+ osc24M: osc24M_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ clock-output-names = "osc24M";
+ };
+
+ osc32k: osc32k_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <32768>;
+ clock-output-names = "osc32k";
+ };
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ /*
+ * map 64 bit address range down to 32 bits,
+ * as the peripherals are all under 512MB.
+ */
+ ranges = <0 0 0 0x20000000>;
+
+ gic: interrupt-controller@01c41000 {
+ compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
+ reg = <0x01c41000 0x1000>,
+ <0x01c42000 0x1000>,
+ <0x01c44000 0x2000>,
+ <0x01c46000 0x2000>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ interrupts = <1 9 0xf04>;
+ };
+
+ timer@06000c00 {
+ compatible = "allwinner,sun4i-a10-timer";
+ reg = <0x06000c00 0xa0>;
+ interrupts = <0 18 4>,
+ <0 19 4>,
+ <0 20 4>,
+ <0 21 4>,
+ <0 22 4>,
+ <0 23 4>;
+
+ clocks = <&osc24M>;
+ };
+
+ uart0: serial@07000000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x07000000 0x400>;
+ interrupts = <0 0 4>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&osc24M>;
+ status = "disabled";
+ };
+
+ uart1: serial@07000400 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x07000400 0x400>;
+ interrupts = <0 1 4>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&osc24M>;
+ status = "disabled";
+ };
+
+ uart2: serial@07000800 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x07000800 0x400>;
+ interrupts = <0 2 4>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&osc24M>;
+ status = "disabled";
+ };
+
+ uart3: serial@07000c00 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x07000c00 0x400>;
+ interrupts = <0 3 4>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&osc24M>;
+ status = "disabled";
+ };
+
+ uart4: serial@07001000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x07001000 0x400>;
+ interrupts = <0 4 4>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&osc24M>;
+ status = "disabled";
+ };
+
+ uart5: serial@07001400 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x07001400 0x400>;
+ interrupts = <0 5 4>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&osc24M>;
+ status = "disabled";
+ };
+
+ r_wdt: watchdog@08001000 {
+ compatible = "allwinner,sun6i-a31-wdt";
+ reg = <0x08001000 0x20>;
+ interrupts = <0 36 4>;
+ };
+
+ r_uart: serial@08002800 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x08002800 0x400>;
+ interrupts = <0 38 4>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&osc24M>;
+ status = "disabled";
+ };
+ };
+};
--
2.1.1
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH v3 3/5] ARM: dts: sun9i: Add A80 Optimus Board support
2014-10-08 13:02 [PATCH v3 0/5] ARM: sunxi: Add basic support for Allwinner A80 SoC Chen-Yu Tsai
[not found] ` <1412773376-25212-1-git-send-email-wens-jdAy2FN1RRM@public.gmane.org>
2014-10-08 13:02 ` [PATCH v3 2/5] ARM: dts: sunxi: Add Allwinner A80 dtsi Chen-Yu Tsai
@ 2014-10-08 13:02 ` Chen-Yu Tsai
[not found] ` <1412773376-25212-4-git-send-email-wens-jdAy2FN1RRM@public.gmane.org>
2014-10-08 13:02 ` [PATCH v3 4/5] devicetree: bindings: Document supported Allwinner sunxi SoCs Chen-Yu Tsai
` (3 subsequent siblings)
6 siblings, 1 reply; 13+ messages in thread
From: Chen-Yu Tsai @ 2014-10-08 13:02 UTC (permalink / raw)
To: Maxime Ripard, Rob Herring, Pawel Moll, Mark Rutland,
Ian Campbell, Kumar Gala
Cc: Chen-Yu Tsai, linux-arm-kernel, devicetree, linux-kernel, Shuge,
Meng Zhang, Gregory CLEMENT
The A80 Optimus Board is was launched with the Allwinner A80 SoC.
It was jointly developed by Allwinner and Merrii.
This board has a UART port, a JTAG connector, USB host ports, a USB
3.0 OTG connector, an HDMI output, a micro SD slot, 8G NAND flash,
4G DRAM, a camera sensor interface, a WiFi/BT combo chip, a headphone
jack, IR receiver, and additional GPIO headers.
This patch adds only basic support.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
arch/arm/boot/dts/Makefile | 2 +
arch/arm/boot/dts/sun9i-a80-optimus.dts | 66 +++++++++++++++++++++++++++++++++
2 files changed, 68 insertions(+)
create mode 100644 arch/arm/boot/dts/sun9i-a80-optimus.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 14dbc6c..6e5474c 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -426,6 +426,8 @@ dtb-$(CONFIG_MACH_SUN7I) += \
sun7i-a20-pcduino3.dtb
dtb-$(CONFIG_MACH_SUN8I) += \
sun8i-a23-ippo-q8h-v5.dtb
+dtb-$(CONFIG_MACH_SUN9I) += \
+ sun9i-a80-optimus.dtb
dtb-$(CONFIG_ARCH_TEGRA) += tegra20-harmony.dtb \
tegra20-iris-512.dtb \
tegra20-medcom-wide.dtb \
diff --git a/arch/arm/boot/dts/sun9i-a80-optimus.dts b/arch/arm/boot/dts/sun9i-a80-optimus.dts
new file mode 100644
index 0000000..f83abab
--- /dev/null
+++ b/arch/arm/boot/dts/sun9i-a80-optimus.dts
@@ -0,0 +1,66 @@
+/*
+ * Copyright 2014 Chen-Yu Tsai
+ *
+ * Chen-Yu Tsai <wens@csie.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this library; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+/include/ "sun9i-a80.dtsi"
+
+/ {
+ model = "Merrii A80 Optimus Board";
+ compatible = "merrii,a80-optimus", "allwinner,sun9i-a80";
+
+ chosen {
+ bootargs = "earlyprintk console=ttyS0,115200";
+ };
+
+ soc {
+ uart0: serial@07000000 {
+ status = "okay";
+ };
+ };
+};
--
2.1.1
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH v3 4/5] devicetree: bindings: Document supported Allwinner sunxi SoCs
2014-10-08 13:02 [PATCH v3 0/5] ARM: sunxi: Add basic support for Allwinner A80 SoC Chen-Yu Tsai
` (2 preceding siblings ...)
2014-10-08 13:02 ` [PATCH v3 3/5] ARM: dts: sun9i: Add A80 Optimus Board support Chen-Yu Tsai
@ 2014-10-08 13:02 ` Chen-Yu Tsai
2014-10-08 13:02 ` [PATCH v3 5/5] Documentation: sunxi: Add A80 datasheet link Chen-Yu Tsai
` (2 subsequent siblings)
6 siblings, 0 replies; 13+ messages in thread
From: Chen-Yu Tsai @ 2014-10-08 13:02 UTC (permalink / raw)
To: Maxime Ripard, Rob Herring, Pawel Moll, Mark Rutland,
Ian Campbell, Kumar Gala
Cc: Chen-Yu Tsai, linux-arm-kernel, devicetree, linux-kernel, Shuge,
Meng Zhang, Gregory CLEMENT
This adds a list of supported Allwinner SoC bindings.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
Documentation/devicetree/bindings/arm/sunxi.txt | 12 ++++++++++++
1 file changed, 12 insertions(+)
create mode 100644 Documentation/devicetree/bindings/arm/sunxi.txt
diff --git a/Documentation/devicetree/bindings/arm/sunxi.txt b/Documentation/devicetree/bindings/arm/sunxi.txt
new file mode 100644
index 0000000..42941fd
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/sunxi.txt
@@ -0,0 +1,12 @@
+Allwinner sunXi Platforms Device Tree Bindings
+
+Each device tree must specify which Allwinner SoC it uses,
+using one of the following compatible strings:
+
+ allwinner,sun4i-a10
+ allwinner,sun5i-a10s
+ allwinner,sun5i-a13
+ allwinner,sun6i-a31
+ allwinner,sun7i-a20
+ allwinner,sun8i-a23
+ allwinner,sun9i-a80
--
2.1.1
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH v3 5/5] Documentation: sunxi: Add A80 datasheet link
2014-10-08 13:02 [PATCH v3 0/5] ARM: sunxi: Add basic support for Allwinner A80 SoC Chen-Yu Tsai
` (3 preceding siblings ...)
2014-10-08 13:02 ` [PATCH v3 4/5] devicetree: bindings: Document supported Allwinner sunxi SoCs Chen-Yu Tsai
@ 2014-10-08 13:02 ` Chen-Yu Tsai
2014-10-09 2:54 ` [PATCH v3 0/5] ARM: sunxi: Add basic support for Allwinner A80 SoC Andreas Färber
2014-10-10 18:26 ` Maxime Ripard
6 siblings, 0 replies; 13+ messages in thread
From: Chen-Yu Tsai @ 2014-10-08 13:02 UTC (permalink / raw)
To: Maxime Ripard, Rob Herring, Pawel Moll, Mark Rutland,
Ian Campbell, Kumar Gala
Cc: Chen-Yu Tsai, linux-arm-kernel, devicetree, linux-kernel, Shuge,
Meng Zhang, Gregory CLEMENT
We now have initial support for the A80, as well a the datasheet.
Update the documents to reflect this.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
Documentation/arm/sunxi/README | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/Documentation/arm/sunxi/README b/Documentation/arm/sunxi/README
index 57c4da6..e68d163 100644
--- a/Documentation/arm/sunxi/README
+++ b/Documentation/arm/sunxi/README
@@ -58,4 +58,5 @@ SunXi family
* Quad ARM Cortex-A15, Quad ARM Cortex-A7 based SoCs
- Allwinner A80
- + Not Supported
\ No newline at end of file
+ + Datasheet
+ http://dl.linux-sunxi.org/A80/A80_Datasheet_Revision_1.0_0404.pdf
--
2.1.1
^ permalink raw reply related [flat|nested] 13+ messages in thread* Re: [PATCH v3 0/5] ARM: sunxi: Add basic support for Allwinner A80 SoC
2014-10-08 13:02 [PATCH v3 0/5] ARM: sunxi: Add basic support for Allwinner A80 SoC Chen-Yu Tsai
` (4 preceding siblings ...)
2014-10-08 13:02 ` [PATCH v3 5/5] Documentation: sunxi: Add A80 datasheet link Chen-Yu Tsai
@ 2014-10-09 2:54 ` Andreas Färber
[not found] ` <5435F8EB.2040407-l3A5Bk7waGM@public.gmane.org>
2014-10-10 18:26 ` Maxime Ripard
6 siblings, 1 reply; 13+ messages in thread
From: Andreas Färber @ 2014-10-09 2:54 UTC (permalink / raw)
To: Chen-Yu Tsai, Maxime Ripard
Cc: Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
devicetree, linux-kernel, Gregory CLEMENT, Shuge, Meng Zhang,
linux-arm-kernel
[-- Attachment #1: Type: text/plain, Size: 1135 bytes --]
Hi,
Am 08.10.2014 um 15:02 schrieb Chen-Yu Tsai:
> This is v3 of the initial Allwinner A80 support series.
> This patch series adds very basic support for Allwinner's A80 SoC,
> a big.LITTLE architecture with 4 Cortex-A7s and 4 Cortex-A15s.
>
> Development is done on the A80 Optimus Board, the defacto development
> board for the A80, with the accompanying SDK as a reference.
>
> So far I've been unable to get the board to boot from MMC, or
> using Android fastboot. I'm using Allwinner's FEL mode to load
> the bootloader and kernel+dtb image over USB. Notes on my attempts
> can be found here: http://linux-sunxi.org/User:Wens#A80_Optimus
Tested-by: Andreas Färber <afaerber@suse.de>
With this patch set on top of Maxime's sunxi-next branch, I get as far
as searching for the rootfs.
CPUs 1-7 fail to boot with -38, which I guess is due to the vendor
U-Boot not yet supporting PSCI.
Thanks a lot for your work and help, Chen-Yu!
Regards,
Andreas
--
SUSE LINUX Products GmbH, Maxfeldstr. 5, 90409 Nürnberg, Germany
GF: Jeff Hawn, Jennifer Guild, Felix Imendörffer; HRB 16746 AG Nürnberg
[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 836 bytes --]
^ permalink raw reply [flat|nested] 13+ messages in thread* Re: [PATCH v3 0/5] ARM: sunxi: Add basic support for Allwinner A80 SoC
2014-10-08 13:02 [PATCH v3 0/5] ARM: sunxi: Add basic support for Allwinner A80 SoC Chen-Yu Tsai
` (5 preceding siblings ...)
2014-10-09 2:54 ` [PATCH v3 0/5] ARM: sunxi: Add basic support for Allwinner A80 SoC Andreas Färber
@ 2014-10-10 18:26 ` Maxime Ripard
6 siblings, 0 replies; 13+ messages in thread
From: Maxime Ripard @ 2014-10-10 18:26 UTC (permalink / raw)
To: Chen-Yu Tsai
Cc: Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
linux-arm-kernel, devicetree, linux-kernel, Shuge, Meng Zhang,
Gregory CLEMENT
[-- Attachment #1: Type: text/plain, Size: 1198 bytes --]
On Wed, Oct 08, 2014 at 09:02:51PM +0800, Chen-Yu Tsai wrote:
> Hi everyone,
>
> This is v3 of the initial Allwinner A80 support series.
> This patch series adds very basic support for Allwinner's A80 SoC,
> a big.LITTLE architecture with 4 Cortex-A7s and 4 Cortex-A15s.
>
> Development is done on the A80 Optimus Board, the defacto development
> board for the A80, with the accompanying SDK as a reference.
>
> So far I've been unable to get the board to boot from MMC, or
> using Android fastboot. I'm using Allwinner's FEL mode to load
> the bootloader and kernel+dtb image over USB. Notes on my attempts
> can be found here: http://linux-sunxi.org/User:Wens#A80_Optimus
>
>
> Patch 1 introduces the compatible string for the A80.
>
> Patch 2 adds a barebone dtsi with just the cpu, memory and uart nodes.
>
> Patch 3 adds a barebone dts for the A80 Optimus Board.
>
> Patch 4 documents all the Allwinner SoCs we currently support.
>
> Patch 5 updates the sunxi README with a link to the A80's datasheet.
Applied all of them, thanks!
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]
^ permalink raw reply [flat|nested] 13+ messages in thread