* [PATCH v6 1/4] pinctrl: Device tree bindings for Qualcomm PMIC GPIO block
2014-10-22 9:58 [PATCH v6 0/4] Qualcomm SPMI PMIC pin controller drivers Ivan T. Ivanov
@ 2014-10-22 9:58 ` Ivan T. Ivanov
[not found] ` <1413971927-9168-1-git-send-email-iivanov-NEYub+7Iv8PQT0dZR+AlfA@public.gmane.org>
` (3 subsequent siblings)
4 siblings, 0 replies; 6+ messages in thread
From: Ivan T. Ivanov @ 2014-10-22 9:58 UTC (permalink / raw)
To: Linus Walleij, Rob Herring, Pawel Moll, Mark Rutland,
Ian Campbell, Kumar Gala
Cc: Bjorn Andersson, devicetree, linux-kernel, linux-arm-msm,
Ivan T. Ivanov
From: Bjorn Andersson <bjorn.andersson@sonymobile.com>
This introduced the device tree bindings for the GPIO block found
in PMIC's from Qualcomm.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
---
.../devicetree/bindings/pinctrl/qcom,pmic-gpio.txt | 215 +++++++++++++++++++++
include/dt-bindings/pinctrl/qcom,pmic-gpio.h | 142 ++++++++++++++
2 files changed, 357 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt
create mode 100644 include/dt-bindings/pinctrl/qcom,pmic-gpio.h
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt
new file mode 100644
index 0000000..7ed0804
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt
@@ -0,0 +1,215 @@
+Qualcomm PMIC GPIO block
+
+This binding describes the GPIO block(s) found in the 8xxx series of
+PMIC's from Qualcomm.
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: must be one of:
+ "qcom,pm8018-gpio"
+ "qcom,pm8038-gpio"
+ "qcom,pm8058-gpio"
+ "qcom,pm8917-gpio"
+ "qcom,pm8921-gpio"
+ "qcom,pm8941-gpio"
+ "qcom,pma8084-gpio"
+
+- reg:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: Register base of the GPIO block and length.
+
+- interrupts:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: Must contain an array of encoded interrupt specifiers for
+ each available GPIO
+
+- gpio-controller:
+ Usage: required
+ Value type: <none>
+ Definition: Mark the device node as a GPIO controller
+
+- #gpio-cells:
+ Usage: required
+ Value type: <u32>
+ Definition: Must be 2;
+ the first cell will be used to define gpio number and the
+ second denotes the flags for this gpio
+
+Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
+a general description of GPIO and interrupt bindings.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+The pin configuration nodes act as a container for an arbitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin or a list of pins. This configuration can include the
+mux function to select on those pin(s), and various pin configuration
+parameters, as listed below.
+
+
+SUBNODES:
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function.
+
+The following generic properties as defined in pinctrl-bindings.txt are valid
+to specify in a pin configuration subnode:
+
+- pins:
+ Usage: required
+ Value type: <string-array>
+ Definition: List of gpio pins affected by the properties specified in
+ this subnode. Valid pins are:
+ gpio1-gpio6 for pm8018
+ gpio1-gpio12 for pm8038
+ gpio1-gpio40 for pm8058
+ gpio1-gpio38 for pm8917
+ gpio1-gpio44 for pm8921
+ gpio1-gpio36 for pm8941
+ gpio1-gpio22 for pma8084
+
+- function:
+ Usage: required
+ Value type: <string>
+ Definition: Specify the alternative function to be configured for the
+ specified pins. Valid values are:
+ "normal",
+ "paired",
+ "func1",
+ "func2",
+ "dtest1",
+ "dtest2",
+ "dtest3",
+ "dtest4"
+
+- bias-disable:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins should be configured as no pull.
+
+- bias-pull-down:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins should be configured as pull down.
+
+- bias-pull-up:
+ Usage: optional
+ Value type: <empty>
+ Definition: The specified pins should be configured as pull up.
+
+- qcom,pull-up-strength:
+ Usage: optional
+ Value type: <u32>
+ Definition: Specifies the strength to use for pull up, if selected.
+ Valid values are; as defined in
+ <dt-bindings/pinctrl/qcom,pmic-gpio.h>:
+ 1: 30uA (PMIC_GPIO_PULL_UP_30)
+ 2: 1.5uA (PMIC_GPIO_PULL_UP_1P5)
+ 3: 31.5uA (PMIC_GPIO_PULL_UP_31P5)
+ 4: 1.5uA + 30uA boost (PMIC_GPIO_PULL_UP_1P5_30)
+ If this property is ommited 30uA strength will be used if
+ pull up is selected
+
+- bias-high-impedance:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins will put in high-Z mode and disabled.
+
+- input-enable:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins are put in input mode.
+
+- output-high:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins are configured in output mode, driven
+ high.
+
+- output-low:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins are configured in output mode, driven
+ low.
+
+- power-source:
+ Usage: optional
+ Value type: <u32>
+ Definition: Selects the power source for the specified pins. Valid
+ power sources are defined per chip in
+ <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+- qcom,drive-strength:
+ Usage: optional
+ Value type: <u32>
+ Definition: Selects the drive strength for the specified pins. Value
+ drive strengths are:
+ 0: no (PMIC_GPIO_STRENGTH_NO)
+ 1: high (PMIC_GPIO_STRENGTH_HIGH) 0.9mA @ 1.8V - 1.9mA @ 2.6V
+ 2: medium (PMIC_GPIO_STRENGTH_MED) 0.6mA @ 1.8V - 1.25mA @ 2.6V
+ 3: low (PMIC_GPIO_STRENGTH_LOW) 0.15mA @ 1.8V - 0.3mA @ 2.6V
+ as defined in <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+- drive-push-pull:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins are configured in push-pull mode.
+
+- drive-open-drain:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins are configured in open-drain mode.
+
+- drive-open-source:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins are configured in open-source mode.
+
+Example:
+
+ pm8921_gpio: gpio@150 {
+ compatible = "qcom,pm8921-gpio";
+ reg = <0x150 0x160>;
+ interrupts = <192 1>, <193 1>, <194 1>,
+ <195 1>, <196 1>, <197 1>,
+ <198 1>, <199 1>, <200 1>,
+ <201 1>, <202 1>, <203 1>,
+ <204 1>, <205 1>, <206 1>,
+ <207 1>, <208 1>, <209 1>,
+ <210 1>, <211 1>, <212 1>,
+ <213 1>, <214 1>, <215 1>,
+ <216 1>, <217 1>, <218 1>,
+ <219 1>, <220 1>, <221 1>,
+ <222 1>, <223 1>, <224 1>,
+ <225 1>, <226 1>, <227 1>,
+ <228 1>, <229 1>, <230 1>,
+ <231 1>, <232 1>, <233 1>,
+ <234 1>, <235 1>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ pm8921_gpio_keys: gpio-keys {
+ volume-keys {
+ pins = "gpio20", "gpio21";
+ function = "normal";
+
+ input-enable;
+ bias-pull-up;
+ drive-push-pull;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+ power-source = <PM8921_GPIO_S4>;
+ };
+ };
+ };
diff --git a/include/dt-bindings/pinctrl/qcom,pmic-gpio.h b/include/dt-bindings/pinctrl/qcom,pmic-gpio.h
new file mode 100644
index 0000000..fa74d7c
--- /dev/null
+++ b/include/dt-bindings/pinctrl/qcom,pmic-gpio.h
@@ -0,0 +1,142 @@
+/*
+ * This header provides constants for the Qualcomm PMIC GPIO binding.
+ */
+
+#ifndef _DT_BINDINGS_PINCTRL_QCOM_PMIC_GPIO_H
+#define _DT_BINDINGS_PINCTRL_QCOM_PMIC_GPIO_H
+
+#define PMIC_GPIO_PULL_UP_30 0
+#define PMIC_GPIO_PULL_UP_1P5 1
+#define PMIC_GPIO_PULL_UP_31P5 2
+#define PMIC_GPIO_PULL_UP_1P5_30 3
+
+#define PMIC_GPIO_STRENGTH_NO 0
+#define PMIC_GPIO_STRENGTH_HIGH 1
+#define PMIC_GPIO_STRENGTH_MED 2
+#define PMIC_GPIO_STRENGTH_LOW 3
+
+/*
+ * Note: PM8018 GPIO3 and GPIO4 are supporting
+ * only S3 and L2 options (1.8V)
+ */
+#define PM8018_GPIO_L6 0
+#define PM8018_GPIO_L5 1
+#define PM8018_GPIO_S3 2
+#define PM8018_GPIO_L14 3
+#define PM8018_GPIO_L2 4
+#define PM8018_GPIO_L4 5
+#define PM8018_GPIO_VDD 6
+
+/*
+ * Note: PM8038 GPIO7 and GPIO8 are supporting
+ * only L11 and L4 options (1.8V)
+ */
+#define PM8038_GPIO_VPH 0
+#define PM8038_GPIO_BB 1
+#define PM8038_GPIO_L11 2
+#define PM8038_GPIO_L15 3
+#define PM8038_GPIO_L4 4
+#define PM8038_GPIO_L3 5
+#define PM8038_GPIO_L17 6
+
+#define PM8058_GPIO_VPH 0
+#define PM8058_GPIO_BB 1
+#define PM8058_GPIO_S3 2
+#define PM8058_GPIO_L3 3
+#define PM8058_GPIO_L7 4
+#define PM8058_GPIO_L6 5
+#define PM8058_GPIO_L5 6
+#define PM8058_GPIO_L2 7
+
+#define PM8917_GPIO_VPH 0
+#define PM8917_GPIO_S4 2
+#define PM8917_GPIO_L15 3
+#define PM8917_GPIO_L4 4
+#define PM8917_GPIO_L3 5
+#define PM8917_GPIO_L17 6
+
+#define PM8921_GPIO_VPH 0
+#define PM8921_GPIO_BB 1
+#define PM8921_GPIO_S4 2
+#define PM8921_GPIO_L15 3
+#define PM8921_GPIO_L4 4
+#define PM8921_GPIO_L3 5
+#define PM8921_GPIO_L17 6
+
+/*
+ * Note: PM8941 gpios from 15 to 18 are supporting
+ * only S3 and L6 options (1.8V)
+ */
+#define PM8941_GPIO_VPH 0
+#define PM8941_GPIO_L1 1
+#define PM8941_GPIO_S3 2
+#define PM8941_GPIO_L6 3
+
+/*
+ * Note: PMA8084 gpios from 15 to 18 are supporting
+ * only S4 and L6 options (1.8V)
+ */
+#define PMA8084_GPIO_VPH 0
+#define PMA8084_GPIO_L1 1
+#define PMA8084_GPIO_S4 2
+#define PMA8084_GPIO_L6 3
+
+/* To be used with "function" */
+#define PMIC_GPIO_FUNC_NORMAL "normal"
+#define PMIC_GPIO_FUNC_PAIRED "paired"
+#define PMIC_GPIO_FUNC_FUNC1 "func1"
+#define PMIC_GPIO_FUNC_FUNC2 "func2"
+#define PMIC_GPIO_FUNC_DTEST1 "dtest1"
+#define PMIC_GPIO_FUNC_DTEST2 "dtest2"
+#define PMIC_GPIO_FUNC_DTEST3 "dtest3"
+#define PMIC_GPIO_FUNC_DTEST4 "dtest4"
+
+#define PM8038_GPIO1_2_LPG_DRV PMIC_GPIO_FUNC_FUNC1
+#define PM8038_GPIO3_5V_BOOST_EN PMIC_GPIO_FUNC_FUNC1
+#define PM8038_GPIO4_SSBI_ALT_CLK PMIC_GPIO_FUNC_FUNC1
+#define PM8038_GPIO5_6_EXT_REG_EN PMIC_GPIO_FUNC_FUNC1
+#define PM8038_GPIO10_11_EXT_REG_EN PMIC_GPIO_FUNC_FUNC1
+#define PM8038_GPIO6_7_CLK PMIC_GPIO_FUNC_FUNC1
+#define PM8038_GPIO9_BAT_ALRM_OUT PMIC_GPIO_FUNC_FUNC1
+#define PM8038_GPIO6_12_KYPD_DRV PMIC_GPIO_FUNC_FUNC2
+
+#define PM8058_GPIO7_8_MP3_CLK PMIC_GPIO_FUNC_FUNC1
+#define PM8058_GPIO7_8_BCLK_19P2MHZ PMIC_GPIO_FUNC_FUNC2
+#define PM8058_GPIO9_26_KYPD_DRV PMIC_GPIO_FUNC_FUNC1
+#define PM8058_GPIO21_23_UART_TX PMIC_GPIO_FUNC_FUNC2
+#define PM8058_GPIO24_26_LPG_DRV PMIC_GPIO_FUNC_FUNC2
+#define PM8058_GPIO33_BCLK_19P2MHZ PMIC_GPIO_FUNC_FUNC1
+#define PM8058_GPIO34_35_MP3_CLK PMIC_GPIO_FUNC_FUNC1
+#define PM8058_GPIO36_BCLK_19P2MHZ PMIC_GPIO_FUNC_FUNC1
+#define PM8058_GPIO37_UPL_OUT PMIC_GPIO_FUNC_FUNC1
+#define PM8058_GPIO37_UART_M_RX PMIC_GPIO_FUNC_FUNC2
+#define PM8058_GPIO38_XO_SLEEP_CLK PMIC_GPIO_FUNC_FUNC1
+#define PM8058_GPIO38_39_CLK_32KHZ PMIC_GPIO_FUNC_FUNC2
+#define PM8058_GPIO39_MP3_CLK PMIC_GPIO_FUNC_FUNC1
+#define PM8058_GPIO40_EXT_BB_EN PMIC_GPIO_FUNC_FUNC1
+
+#define PM8917_GPIO9_18_KEYP_DRV PMIC_GPIO_FUNC_FUNC1
+#define PM8917_GPIO20_BAT_ALRM_OUT PMIC_GPIO_FUNC_FUNC1
+#define PM8917_GPIO21_23_UART_TX PMIC_GPIO_FUNC_FUNC2
+#define PM8917_GPIO25_26_EXT_REG_EN PMIC_GPIO_FUNC_FUNC1
+#define PM8917_GPIO37_38_XO_SLEEP_CLK PMIC_GPIO_FUNC_FUNC1
+#define PM8917_GPIO37_38_MP3_CLK PMIC_GPIO_FUNC_FUNC2
+
+#define PM8941_GPIO9_14_KYPD_DRV PMIC_GPIO_FUNC_FUNC1
+#define PM8941_GPIO15_18_DIV_CLK PMIC_GPIO_FUNC_FUNC1
+#define PM8941_GPIO15_18_SLEEP_CLK PMIC_GPIO_FUNC_FUNC2
+#define PM8941_GPIO23_26_KYPD_DRV PMIC_GPIO_FUNC_FUNC1
+#define PM8941_GPIO23_26_LPG_DRV_HI PMIC_GPIO_FUNC_FUNC2
+#define PM8941_GPIO31_BAT_ALRM_OUT PMIC_GPIO_FUNC_FUNC1
+#define PM8941_GPIO33_36_LPG_DRV_3D PMIC_GPIO_FUNC_FUNC1
+#define PM8941_GPIO33_36_LPG_DRV_HI PMIC_GPIO_FUNC_FUNC2
+
+#define PMA8084_GPIO4_5_LPG_DRV PMIC_GPIO_FUNC_FUNC1
+#define PMA8084_GPIO7_10_LPG_DRV PMIC_GPIO_FUNC_FUNC1
+#define PMA8084_GPIO5_14_KEYP_DRV PMIC_GPIO_FUNC_FUNC2
+#define PMA8084_GPIO19_21_KEYP_DRV PMIC_GPIO_FUNC_FUNC2
+#define PMA8084_GPIO15_18_DIV_CLK PMIC_GPIO_FUNC_FUNC1
+#define PMA8084_GPIO15_18_SLEEP_CLK PMIC_GPIO_FUNC_FUNC2
+#define PMA8084_GPIO22_BAT_ALRM_OUT PMIC_GPIO_FUNC_FUNC1
+
+#endif
--
1.9.1
^ permalink raw reply related [flat|nested] 6+ messages in thread[parent not found: <1413971927-9168-1-git-send-email-iivanov-NEYub+7Iv8PQT0dZR+AlfA@public.gmane.org>]
* [PATCH v6 2/4] pinctrl: Device tree bindings for Qualcomm PMIC MPP block
[not found] ` <1413971927-9168-1-git-send-email-iivanov-NEYub+7Iv8PQT0dZR+AlfA@public.gmane.org>
@ 2014-10-22 9:58 ` Ivan T. Ivanov
0 siblings, 0 replies; 6+ messages in thread
From: Ivan T. Ivanov @ 2014-10-22 9:58 UTC (permalink / raw)
To: Linus Walleij, Rob Herring, Pawel Moll, Mark Rutland,
Ian Campbell, Kumar Gala
Cc: Ivan T. Ivanov, Bjorn Andersson,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-arm-msm-u79uwXL29TY76Z2rM5mHXA
DeviceTree binding documentation for Qualcomm SPMI PMIC MPP
pinctrl drivers.
Signed-off-by: Ivan T. Ivanov <iivanov-NEYub+7Iv8PQT0dZR+AlfA@public.gmane.org>
Acked-by: Bjorn Andersson <bjorn.andersson-/MT0OVThwyLZJqsBc5GL+g@public.gmane.org>
---
.../devicetree/bindings/pinctrl/qcom,pmic-mpp.txt | 162 +++++++++++++++++++++
include/dt-bindings/pinctrl/qcom,pmic-mpp.h | 44 ++++++
2 files changed, 206 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt
create mode 100644 include/dt-bindings/pinctrl/qcom,pmic-mpp.h
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt
new file mode 100644
index 0000000..854774b
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt
@@ -0,0 +1,162 @@
+Qualcomm PMIC Multi-Purpose Pin (MPP) block
+
+This binding describes the MPP block(s) found in the 8xxx series
+of PMIC's from Qualcomm.
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: Should contain one of:
+ "qcom,pm8841-mpp",
+ "qcom,pm8941-mpp",
+ "qcom,pma8084-mpp",
+
+- reg:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: Register base of the MPP block and length.
+
+- interrupts:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: Must contain an array of encoded interrupt specifiers for
+ each available MPP
+
+- gpio-controller:
+ Usage: required
+ Value type: <none>
+ Definition: Mark the device node as a GPIO controller
+
+- #gpio-cells:
+ Usage: required
+ Value type: <u32>
+ Definition: Must be 2;
+ the first cell will be used to define MPP number and the
+ second denotes the flags for this MPP
+
+Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
+a general description of GPIO and interrupt bindings.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+The pin configuration nodes act as a container for an arbitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin or a list of pins. This configuration can include the
+mux function to select on those pin(s), and various pin configuration
+parameters, as listed below.
+
+SUBNODES:
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function.
+
+The following generic properties as defined in pinctrl-bindings.txt are valid
+to specify in a pin configuration subnode:
+
+- pins:
+ Usage: required
+ Value type: <string-array>
+ Definition: List of MPP pins affected by the properties specified in
+ this subnode. Valid pins are:
+ mpp1-mpp4 for pm8841
+ mpp1-mpp8 for pm8941
+ mpp1-mpp4 for pma8084
+
+- function:
+ Usage: required
+ Value type: <string>
+ Definition: Specify the alternative function to be configured for the
+ specified pins. Valid values are:
+ "normal",
+ "paired",
+ "dtest1",
+ "dtest2",
+ "dtest3",
+ "dtest4"
+
+- bias-disable:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins should be configured as no pull.
+
+- bias-pull-up:
+ Usage: optional
+ Value type: <u32>
+ Definition: The specified pins should be configured as pull up.
+ Valid values are 600, 10000 and 30000 in bidirectional mode
+ only, i.e. when operating in qcom,analog-mode and input and
+ outputs are enabled. The hardware ignores the configuration
+ when operating in other modes.
+
+- bias-high-impedance:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins will put in high-Z mode and disabled.
+
+- input-enable:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins are put in input mode, i.e. their input
+ buffer is enabled
+
+- output-high:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins are configured in output mode, driven
+ high.
+
+- output-low:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins are configured in output mode, driven
+ low.
+
+- power-source:
+ Usage: optional
+ Value type: <u32>
+ Definition: Selects the power source for the specified pins. Valid power
+ sources are defined in <dt-bindings/pinctrl/qcom,pmic-mpp.h>
+
+- qcom,analog-mode:
+ Usage: optional
+ Value type: <none>
+ Definition: Selects Analog mode of operation: combined with input-enable
+ and/or output-high, output-low MPP could operate as
+ Bidirectional Logic, Analog Input, Analog Output.
+
+- qcom,amux-route:
+ Usage: optional
+ Value type: <u32>
+ Definition: Selects the source for analog input. Valid values are
+ defined in <dt-bindings/pinctrl/qcom,pmic-mpp.h>
+ PMIC_MPP_AMUX_ROUTE_CH5, PMIC_MPP_AMUX_ROUTE_CH6...
+
+Example:
+
+ mpps@a000 {
+ compatible = "qcom,pm8841-mpp";
+ reg = <0xa000>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupts = <4 0xa0 0 0>, <4 0xa1 0 0>, <4 0xa2 0 0>, <4 0xa3 0 0>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pm8841_default>;
+
+ pm8841_default: default {
+ gpio {
+ pins = "mpp1", "mpp2", "mpp3", "mpp4";
+ function = "normal";
+ input-enable;
+ power-source = <PM8841_MPP_S3>;
+ };
+ };
+ };
diff --git a/include/dt-bindings/pinctrl/qcom,pmic-mpp.h b/include/dt-bindings/pinctrl/qcom,pmic-mpp.h
new file mode 100644
index 0000000..d2c7dab
--- /dev/null
+++ b/include/dt-bindings/pinctrl/qcom,pmic-mpp.h
@@ -0,0 +1,44 @@
+/*
+ * This header provides constants for the Qualcomm PMIC's
+ * Multi-Purpose Pin binding.
+ */
+
+#ifndef _DT_BINDINGS_PINCTRL_QCOM_PMIC_MPP_H
+#define _DT_BINDINGS_PINCTRL_QCOM_PMIC_MPP_H
+
+/* power-source */
+#define PM8841_MPP_VPH 0
+#define PM8841_MPP_S3 2
+
+#define PM8941_MPP_VPH 0
+#define PM8941_MPP_L1 1
+#define PM8941_MPP_S3 2
+#define PM8941_MPP_L6 3
+
+#define PMA8084_MPP_VPH 0
+#define PMA8084_MPP_L1 1
+#define PMA8084_MPP_S4 2
+#define PMA8084_MPP_L6 3
+
+/*
+ * Analog Input - Set the source for analog input.
+ * To be used with "qcom,amux-route" property
+ */
+#define PMIC_MPP_AMUX_ROUTE_CH5 0
+#define PMIC_MPP_AMUX_ROUTE_CH6 1
+#define PMIC_MPP_AMUX_ROUTE_CH7 2
+#define PMIC_MPP_AMUX_ROUTE_CH8 3
+#define PMIC_MPP_AMUX_ROUTE_ABUS1 4
+#define PMIC_MPP_AMUX_ROUTE_ABUS2 5
+#define PMIC_MPP_AMUX_ROUTE_ABUS3 6
+#define PMIC_MPP_AMUX_ROUTE_ABUS4 7
+
+/* To be used with "function" */
+#define PMIC_MPP_FUNC_NORMAL "normal"
+#define PMIC_MPP_FUNC_PAIRED "paired"
+#define PMIC_MPP_FUNC_DTEST1 "dtest1"
+#define PMIC_MPP_FUNC_DTEST2 "dtest2"
+#define PMIC_MPP_FUNC_DTEST3 "dtest3"
+#define PMIC_MPP_FUNC_DTEST4 "dtest4"
+
+#endif
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH v6 3/4] pinctrl: Qualcomm SPMI PMIC GPIO pin controller driver
2014-10-22 9:58 [PATCH v6 0/4] Qualcomm SPMI PMIC pin controller drivers Ivan T. Ivanov
2014-10-22 9:58 ` [PATCH v6 1/4] pinctrl: Device tree bindings for Qualcomm PMIC GPIO block Ivan T. Ivanov
[not found] ` <1413971927-9168-1-git-send-email-iivanov-NEYub+7Iv8PQT0dZR+AlfA@public.gmane.org>
@ 2014-10-22 9:58 ` Ivan T. Ivanov
2014-10-22 9:58 ` [PATCH v6 4/4] pinctrl: Qualcomm SPMI PMIC MPP " Ivan T. Ivanov
2014-10-28 16:29 ` [PATCH v6 0/4] Qualcomm SPMI PMIC pin controller drivers Linus Walleij
4 siblings, 0 replies; 6+ messages in thread
From: Ivan T. Ivanov @ 2014-10-22 9:58 UTC (permalink / raw)
To: Linus Walleij, Grant Likely, Rob Herring
Cc: Ivan T. Ivanov, Bjorn Andersson, Georgi Djakov, Andy Gross,
linux-kernel, devicetree, linux-arm-msm
This is the pinctrl, pinmux, pinconf and gpiolib driver for the
Qualcomm GPIO sub-function blocks found in the PMIC chips.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
---
drivers/pinctrl/qcom/Kconfig | 13 +
drivers/pinctrl/qcom/Makefile | 1 +
drivers/pinctrl/qcom/pinctrl-spmi-gpio.c | 933 +++++++++++++++++++++++++++++++
3 files changed, 947 insertions(+)
create mode 100644 drivers/pinctrl/qcom/pinctrl-spmi-gpio.c
diff --git a/drivers/pinctrl/qcom/Kconfig b/drivers/pinctrl/qcom/Kconfig
index 81275af..3cd243c 100644
--- a/drivers/pinctrl/qcom/Kconfig
+++ b/drivers/pinctrl/qcom/Kconfig
@@ -47,4 +47,17 @@ config PINCTRL_MSM8X74
This is the pinctrl, pinmux, pinconf and gpiolib driver for the
Qualcomm TLMM block found in the Qualcomm 8974 platform.
+config PINCTRL_QCOM_SPMI_PMIC
+ tristate "Qualcomm SPMI PMIC pin controller driver"
+ depends on GPIOLIB && OF && SPMI
+ select REGMAP_SPMI
+ select PINMUX
+ select PINCONF
+ select GENERIC_PINCONF
+ help
+ This is the pinctrl, pinmux, pinconf and gpiolib driver for the
+ Qualcomm GPIO and MPP blocks found in the Qualcomm PMIC's chips,
+ which are using SPMI for communication with SoC. Example PMIC's
+ devices are pm8841, pm8941 and pma8084.
+
endif
diff --git a/drivers/pinctrl/qcom/Makefile b/drivers/pinctrl/qcom/Makefile
index ba8519f..9b49c65a 100644
--- a/drivers/pinctrl/qcom/Makefile
+++ b/drivers/pinctrl/qcom/Makefile
@@ -5,3 +5,4 @@ obj-$(CONFIG_PINCTRL_APQ8084) += pinctrl-apq8084.o
obj-$(CONFIG_PINCTRL_IPQ8064) += pinctrl-ipq8064.o
obj-$(CONFIG_PINCTRL_MSM8960) += pinctrl-msm8960.o
obj-$(CONFIG_PINCTRL_MSM8X74) += pinctrl-msm8x74.o
+obj-$(CONFIG_PINCTRL_QCOM_SPMI_PMIC) += pinctrl-spmi-gpio.o
diff --git a/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c b/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c
new file mode 100644
index 0000000..b863b50
--- /dev/null
+++ b/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c
@@ -0,0 +1,933 @@
+/*
+ * Copyright (c) 2012-2014, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/gpio.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/pinctrl/pinconf-generic.h>
+#include <linux/pinctrl/pinconf.h>
+#include <linux/pinctrl/pinmux.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+#include "../core.h"
+#include "../pinctrl-utils.h"
+
+#define PMIC_GPIO_ADDRESS_RANGE 0x100
+
+/* type and subtype registers base address offsets */
+#define PMIC_GPIO_REG_TYPE 0x4
+#define PMIC_GPIO_REG_SUBTYPE 0x5
+
+/* GPIO peripheral type and subtype out_values */
+#define PMIC_GPIO_TYPE 0x10
+#define PMIC_GPIO_SUBTYPE_GPIO_4CH 0x1
+#define PMIC_GPIO_SUBTYPE_GPIOC_4CH 0x5
+#define PMIC_GPIO_SUBTYPE_GPIO_8CH 0x9
+#define PMIC_GPIO_SUBTYPE_GPIOC_8CH 0xd
+
+#define PMIC_MPP_REG_RT_STS 0x10
+#define PMIC_MPP_REG_RT_STS_VAL_MASK 0x1
+
+/* control register base address offsets */
+#define PMIC_GPIO_REG_MODE_CTL 0x40
+#define PMIC_GPIO_REG_DIG_VIN_CTL 0x41
+#define PMIC_GPIO_REG_DIG_PULL_CTL 0x42
+#define PMIC_GPIO_REG_DIG_OUT_CTL 0x45
+#define PMIC_GPIO_REG_EN_CTL 0x46
+
+/* PMIC_GPIO_REG_MODE_CTL */
+#define PMIC_GPIO_REG_MODE_VALUE_SHIFT 0x1
+#define PMIC_GPIO_REG_MODE_FUNCTION_SHIFT 1
+#define PMIC_GPIO_REG_MODE_FUNCTION_MASK 0x7
+#define PMIC_GPIO_REG_MODE_DIR_SHIFT 4
+#define PMIC_GPIO_REG_MODE_DIR_MASK 0x7
+
+/* PMIC_GPIO_REG_DIG_VIN_CTL */
+#define PMIC_GPIO_REG_VIN_SHIFT 0
+#define PMIC_GPIO_REG_VIN_MASK 0x7
+
+/* PMIC_GPIO_REG_DIG_PULL_CTL */
+#define PMIC_GPIO_REG_PULL_SHIFT 0
+#define PMIC_GPIO_REG_PULL_MASK 0x7
+
+#define PMIC_GPIO_PULL_DOWN 4
+#define PMIC_GPIO_PULL_DISABLE 5
+
+/* PMIC_GPIO_REG_DIG_OUT_CTL */
+#define PMIC_GPIO_REG_OUT_STRENGTH_SHIFT 0
+#define PMIC_GPIO_REG_OUT_STRENGTH_MASK 0x3
+#define PMIC_GPIO_REG_OUT_TYPE_SHIFT 4
+#define PMIC_GPIO_REG_OUT_TYPE_MASK 0x3
+
+/*
+ * Output type - indicates pin should be configured as push-pull,
+ * open drain or open source.
+ */
+#define PMIC_GPIO_OUT_BUF_CMOS 0
+#define PMIC_GPIO_OUT_BUF_OPEN_DRAIN_NMOS 1
+#define PMIC_GPIO_OUT_BUF_OPEN_DRAIN_PMOS 2
+
+/* PMIC_GPIO_REG_EN_CTL */
+#define PMIC_GPIO_REG_MASTER_EN_SHIFT 7
+
+#define PMIC_GPIO_PHYSICAL_OFFSET 1
+
+/* Qualcomm specific pin configurations */
+#define PMIC_GPIO_CONF_PULL_UP (PIN_CONFIG_END + 1)
+#define PMIC_GPIO_CONF_STRENGTH (PIN_CONFIG_END + 2)
+
+/**
+ * struct pmic_gpio_pad - keep current GPIO settings
+ * @base: Address base in SPMI device.
+ * @irq: IRQ number which this GPIO generate.
+ * @is_enabled: Set to false when GPIO should be put in high Z state.
+ * @out_value: Cached pin output value
+ * @have_buffer: Set to true if GPIO output could be configured in push-pull,
+ * open-drain or open-source mode.
+ * @output_enabled: Set to true if GPIO output logic is enabled.
+ * @input_enabled: Set to true if GPIO input buffer logic is enabled.
+ * @num_sources: Number of power-sources supported by this GPIO.
+ * @power_source: Current power-source used.
+ * @buffer_type: Push-pull, open-drain or open-source.
+ * @pullup: Constant current which flow trough GPIO output buffer.
+ * @strength: No, Low, Medium, High
+ * @function: See pmic_gpio_functions[]
+ */
+struct pmic_gpio_pad {
+ u16 base;
+ int irq;
+ bool is_enabled;
+ bool out_value;
+ bool have_buffer;
+ bool output_enabled;
+ bool input_enabled;
+ unsigned int num_sources;
+ unsigned int power_source;
+ unsigned int buffer_type;
+ unsigned int pullup;
+ unsigned int strength;
+ unsigned int function;
+};
+
+struct pmic_gpio_state {
+ struct device *dev;
+ struct regmap *map;
+ struct pinctrl_dev *ctrl;
+ struct gpio_chip chip;
+};
+
+struct pmic_gpio_bindings {
+ const char *property;
+ unsigned param;
+};
+
+static struct pmic_gpio_bindings pmic_gpio_bindings[] = {
+ {"qcom,pull-up-strength", PMIC_GPIO_CONF_PULL_UP},
+ {"qcom,drive-strength", PMIC_GPIO_CONF_STRENGTH},
+};
+
+static const char *const pmic_gpio_groups[] = {
+ "gpio1", "gpio2", "gpio3", "gpio4", "gpio5", "gpio6", "gpio7", "gpio8",
+ "gpio9", "gpio10", "gpio11", "gpio12", "gpio13", "gpio14", "gpio15",
+ "gpio16", "gpio17", "gpio18", "gpio19", "gpio20", "gpio21", "gpio22",
+ "gpio23", "gpio24", "gpio25", "gpio26", "gpio27", "gpio28", "gpio29",
+ "gpio30", "gpio31", "gpio32", "gpio33", "gpio34", "gpio35", "gpio36",
+};
+
+static const char *const pmic_gpio_functions[] = {
+ PMIC_GPIO_FUNC_NORMAL, PMIC_GPIO_FUNC_PAIRED,
+ PMIC_GPIO_FUNC_FUNC1, PMIC_GPIO_FUNC_FUNC2,
+ PMIC_GPIO_FUNC_DTEST1, PMIC_GPIO_FUNC_DTEST2,
+ PMIC_GPIO_FUNC_DTEST3, PMIC_GPIO_FUNC_DTEST4,
+};
+
+static inline struct pmic_gpio_state *to_gpio_state(struct gpio_chip *chip)
+{
+ return container_of(chip, struct pmic_gpio_state, chip);
+};
+
+static int pmic_gpio_read(struct pmic_gpio_state *state,
+ struct pmic_gpio_pad *pad, unsigned int addr)
+{
+ unsigned int val;
+ int ret;
+
+ ret = regmap_read(state->map, pad->base + addr, &val);
+ if (ret < 0)
+ dev_err(state->dev, "read 0x%x failed\n", addr);
+ else
+ ret = val;
+
+ return ret;
+}
+
+static int pmic_gpio_write(struct pmic_gpio_state *state,
+ struct pmic_gpio_pad *pad, unsigned int addr,
+ unsigned int val)
+{
+ int ret;
+
+ ret = regmap_write(state->map, pad->base + addr, val);
+ if (ret < 0)
+ dev_err(state->dev, "write 0x%x failed\n", addr);
+
+ return ret;
+}
+
+static int pmic_gpio_get_groups_count(struct pinctrl_dev *pctldev)
+{
+ /* Every PIN is a group */
+ return pctldev->desc->npins;
+}
+
+static const char *pmic_gpio_get_group_name(struct pinctrl_dev *pctldev,
+ unsigned pin)
+{
+ return pctldev->desc->pins[pin].name;
+}
+
+static int pmic_gpio_get_group_pins(struct pinctrl_dev *pctldev, unsigned pin,
+ const unsigned **pins, unsigned *num_pins)
+{
+ *pins = &pctldev->desc->pins[pin].number;
+ *num_pins = 1;
+ return 0;
+}
+
+static int pmic_gpio_parse_dt_config(struct device_node *np,
+ struct pinctrl_dev *pctldev,
+ unsigned long **configs,
+ unsigned int *nconfs)
+{
+ struct pmic_gpio_bindings *par;
+ unsigned long cfg;
+ int ret, i;
+ u32 val;
+
+ for (i = 0; i < ARRAY_SIZE(pmic_gpio_bindings); i++) {
+ par = &pmic_gpio_bindings[i];
+ ret = of_property_read_u32(np, par->property, &val);
+
+ /* property not found */
+ if (ret == -EINVAL)
+ continue;
+
+ /* use zero as default value */
+ if (ret)
+ val = 0;
+
+ dev_dbg(pctldev->dev, "found %s with value %u\n",
+ par->property, val);
+
+ cfg = pinconf_to_config_packed(par->param, val);
+
+ ret = pinctrl_utils_add_config(pctldev, configs, nconfs, cfg);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
+static int pmic_gpio_dt_subnode_to_map(struct pinctrl_dev *pctldev,
+ struct device_node *np,
+ struct pinctrl_map **map,
+ unsigned *reserv, unsigned *nmaps,
+ enum pinctrl_map_type type)
+{
+ unsigned long *configs = NULL;
+ unsigned nconfs = 0;
+ struct property *prop;
+ const char *group;
+ int ret;
+
+ ret = pmic_gpio_parse_dt_config(np, pctldev, &configs, &nconfs);
+ if (ret < 0)
+ return ret;
+
+ if (!nconfs)
+ return 0;
+
+ ret = of_property_count_strings(np, "pins");
+ if (ret < 0)
+ goto exit;
+
+ ret = pinctrl_utils_reserve_map(pctldev, map, reserv, nmaps, ret);
+ if (ret < 0)
+ goto exit;
+
+ of_property_for_each_string(np, "pins", prop, group) {
+ ret = pinctrl_utils_add_map_configs(pctldev, map,
+ reserv, nmaps, group,
+ configs, nconfs, type);
+ if (ret < 0)
+ break;
+ }
+exit:
+ kfree(configs);
+ return ret;
+}
+
+static int pmic_gpio_dt_node_to_map(struct pinctrl_dev *pctldev,
+ struct device_node *np_config,
+ struct pinctrl_map **map, unsigned *nmaps)
+{
+ enum pinctrl_map_type type;
+ struct device_node *np;
+ unsigned reserv;
+ int ret;
+
+ ret = 0;
+ *map = NULL;
+ *nmaps = 0;
+ reserv = 0;
+ type = PIN_MAP_TYPE_CONFIGS_GROUP;
+
+ for_each_child_of_node(np_config, np) {
+ ret = pinconf_generic_dt_subnode_to_map(pctldev, np, map,
+ &reserv, nmaps, type);
+ if (ret)
+ break;
+
+ ret = pmic_gpio_dt_subnode_to_map(pctldev, np, map, &reserv,
+ nmaps, type);
+ if (ret)
+ break;
+ }
+
+ if (ret < 0)
+ pinctrl_utils_dt_free_map(pctldev, *map, *nmaps);
+
+ return ret;
+}
+
+static const struct pinctrl_ops pmic_gpio_pinctrl_ops = {
+ .get_groups_count = pmic_gpio_get_groups_count,
+ .get_group_name = pmic_gpio_get_group_name,
+ .get_group_pins = pmic_gpio_get_group_pins,
+ .dt_node_to_map = pmic_gpio_dt_node_to_map,
+ .dt_free_map = pinctrl_utils_dt_free_map,
+};
+
+static int pmic_gpio_get_functions_count(struct pinctrl_dev *pctldev)
+{
+ return ARRAY_SIZE(pmic_gpio_functions);
+}
+
+static const char *pmic_gpio_get_function_name(struct pinctrl_dev *pctldev,
+ unsigned function)
+{
+ return pmic_gpio_functions[function];
+}
+
+static int pmic_gpio_get_function_groups(struct pinctrl_dev *pctldev,
+ unsigned function,
+ const char *const **groups,
+ unsigned *const num_qgroups)
+{
+ *groups = pmic_gpio_groups;
+ *num_qgroups = pctldev->desc->npins;
+ return 0;
+}
+
+static int pmic_gpio_set_mux(struct pinctrl_dev *pctldev, unsigned function,
+ unsigned pin)
+{
+ struct pmic_gpio_state *state = pinctrl_dev_get_drvdata(pctldev);
+ struct pmic_gpio_pad *pad;
+ unsigned int val;
+ int ret;
+
+ pad = pctldev->desc->pins[pin].drv_data;
+
+ pad->function = function;
+
+ val = 0;
+ if (pad->output_enabled) {
+ if (pad->input_enabled)
+ val = 2;
+ else
+ val = 1;
+ }
+
+ val |= pad->function << PMIC_GPIO_REG_MODE_FUNCTION_SHIFT;
+ val |= pad->out_value & PMIC_GPIO_REG_MODE_VALUE_SHIFT;
+
+ ret = pmic_gpio_write(state, pad, PMIC_GPIO_REG_MODE_CTL, val);
+ if (ret < 0)
+ return ret;
+
+ val = pad->is_enabled << PMIC_GPIO_REG_MASTER_EN_SHIFT;
+
+ return pmic_gpio_write(state, pad, PMIC_GPIO_REG_EN_CTL, val);
+}
+
+static const struct pinmux_ops pmic_gpio_pinmux_ops = {
+ .get_functions_count = pmic_gpio_get_functions_count,
+ .get_function_name = pmic_gpio_get_function_name,
+ .get_function_groups = pmic_gpio_get_function_groups,
+ .set_mux = pmic_gpio_set_mux,
+};
+
+static int pmic_gpio_config_get(struct pinctrl_dev *pctldev,
+ unsigned int pin, unsigned long *config)
+{
+ unsigned param = pinconf_to_config_param(*config);
+ struct pmic_gpio_pad *pad;
+ unsigned arg;
+
+ pad = pctldev->desc->pins[pin].drv_data;
+
+ switch (param) {
+ case PIN_CONFIG_DRIVE_PUSH_PULL:
+ arg = pad->buffer_type == PMIC_GPIO_OUT_BUF_CMOS;
+ break;
+ case PIN_CONFIG_DRIVE_OPEN_DRAIN:
+ arg = pad->buffer_type == PMIC_GPIO_OUT_BUF_OPEN_DRAIN_NMOS;
+ break;
+ case PIN_CONFIG_DRIVE_OPEN_SOURCE:
+ arg = pad->buffer_type == PMIC_GPIO_OUT_BUF_OPEN_DRAIN_PMOS;
+ break;
+ case PIN_CONFIG_BIAS_PULL_DOWN:
+ arg = pad->pullup == PMIC_GPIO_PULL_DOWN;
+ break;
+ case PIN_CONFIG_BIAS_DISABLE:
+ arg = pad->pullup = PMIC_GPIO_PULL_DISABLE;
+ break;
+ case PIN_CONFIG_BIAS_PULL_UP:
+ arg = pad->pullup == PMIC_GPIO_PULL_UP_30;
+ break;
+ case PIN_CONFIG_BIAS_HIGH_IMPEDANCE:
+ arg = !pad->is_enabled;
+ break;
+ case PIN_CONFIG_POWER_SOURCE:
+ arg = pad->power_source;
+ break;
+ case PIN_CONFIG_INPUT_ENABLE:
+ arg = pad->input_enabled;
+ break;
+ case PIN_CONFIG_OUTPUT:
+ arg = pad->out_value;
+ break;
+ case PMIC_GPIO_CONF_PULL_UP:
+ arg = pad->pullup;
+ break;
+ case PMIC_GPIO_CONF_STRENGTH:
+ arg = pad->strength;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ *config = pinconf_to_config_packed(param, arg);
+ return 0;
+}
+
+static int pmic_gpio_config_set(struct pinctrl_dev *pctldev, unsigned int pin,
+ unsigned long *configs, unsigned nconfs)
+{
+ struct pmic_gpio_state *state = pinctrl_dev_get_drvdata(pctldev);
+ struct pmic_gpio_pad *pad;
+ unsigned param, arg;
+ unsigned int val;
+ int i, ret;
+
+ pad = pctldev->desc->pins[pin].drv_data;
+
+ for (i = 0; i < nconfs; i++) {
+ param = pinconf_to_config_param(configs[i]);
+ arg = pinconf_to_config_argument(configs[i]);
+
+ switch (param) {
+ case PIN_CONFIG_DRIVE_PUSH_PULL:
+ pad->buffer_type = PMIC_GPIO_OUT_BUF_CMOS;
+ break;
+ case PIN_CONFIG_DRIVE_OPEN_DRAIN:
+ if (!pad->have_buffer)
+ return -EINVAL;
+ pad->buffer_type = PMIC_GPIO_OUT_BUF_OPEN_DRAIN_NMOS;
+ break;
+ case PIN_CONFIG_DRIVE_OPEN_SOURCE:
+ if (!pad->have_buffer)
+ return -EINVAL;
+ pad->buffer_type = PMIC_GPIO_OUT_BUF_OPEN_DRAIN_PMOS;
+ break;
+ case PIN_CONFIG_BIAS_DISABLE:
+ pad->pullup = PMIC_GPIO_PULL_DISABLE;
+ break;
+ case PIN_CONFIG_BIAS_PULL_UP:
+ pad->pullup = PMIC_GPIO_PULL_UP_30;
+ break;
+ case PIN_CONFIG_BIAS_PULL_DOWN:
+ if (arg)
+ pad->pullup = PMIC_GPIO_PULL_DOWN;
+ else
+ pad->pullup = PMIC_GPIO_PULL_DISABLE;
+ break;
+ case PIN_CONFIG_BIAS_HIGH_IMPEDANCE:
+ pad->is_enabled = false;
+ break;
+ case PIN_CONFIG_POWER_SOURCE:
+ if (arg > pad->num_sources)
+ return -EINVAL;
+ pad->power_source = arg;
+ break;
+ case PIN_CONFIG_INPUT_ENABLE:
+ pad->input_enabled = arg ? true : false;
+ break;
+ case PIN_CONFIG_OUTPUT:
+ pad->output_enabled = true;
+ pad->out_value = arg;
+ break;
+ case PMIC_GPIO_CONF_PULL_UP:
+ if (arg > PMIC_GPIO_PULL_UP_1P5_30)
+ return -EINVAL;
+ pad->pullup = arg;
+ break;
+ case PMIC_GPIO_CONF_STRENGTH:
+ if (arg > PMIC_GPIO_STRENGTH_LOW)
+ return -EINVAL;
+ pad->strength = arg;
+ break;
+ default:
+ return -EINVAL;
+ }
+ }
+
+ val = pad->power_source << PMIC_GPIO_REG_VIN_SHIFT;
+
+ ret = pmic_gpio_write(state, pad, PMIC_GPIO_REG_DIG_VIN_CTL, val);
+ if (ret < 0)
+ return ret;
+
+ val = pad->pullup << PMIC_GPIO_REG_PULL_SHIFT;
+
+ ret = pmic_gpio_write(state, pad, PMIC_GPIO_REG_DIG_PULL_CTL, val);
+ if (ret < 0)
+ return ret;
+
+ val = pad->buffer_type << PMIC_GPIO_REG_OUT_TYPE_SHIFT;
+ val = pad->strength << PMIC_GPIO_REG_OUT_STRENGTH_SHIFT;
+
+ ret = pmic_gpio_write(state, pad, PMIC_GPIO_REG_DIG_OUT_CTL, val);
+ if (ret < 0)
+ return ret;
+
+ val = 0;
+ if (pad->output_enabled) {
+ if (pad->input_enabled)
+ val = 2;
+ else
+ val = 1;
+ }
+
+ val = val << PMIC_GPIO_REG_MODE_DIR_SHIFT;
+ val |= pad->function << PMIC_GPIO_REG_MODE_FUNCTION_SHIFT;
+ val |= pad->out_value & PMIC_GPIO_REG_MODE_VALUE_SHIFT;
+
+ return pmic_gpio_write(state, pad, PMIC_GPIO_REG_MODE_CTL, val);
+}
+
+static void pmic_gpio_config_dbg_show(struct pinctrl_dev *pctldev,
+ struct seq_file *s, unsigned pin)
+{
+ struct pmic_gpio_state *state = pinctrl_dev_get_drvdata(pctldev);
+ struct pmic_gpio_pad *pad;
+ int ret, val;
+
+ static const char *const biases[] = {
+ "pull-up 30uA", "pull-up 1.5uA", "pull-up 31.5uA",
+ "pull-up 1.5uA + 30uA boost", "pull-down 10uA", "no pull"
+ };
+ static const char *const buffer_types[] = {
+ "push-pull", "open-drain", "open-source"
+ };
+ static const char *const strengths[] = {
+ "no", "high", "medium", "low"
+ };
+
+ pad = pctldev->desc->pins[pin].drv_data;
+
+ seq_printf(s, " gpio%-2d:", pin + PMIC_GPIO_PHYSICAL_OFFSET);
+
+ val = pmic_gpio_read(state, pad, PMIC_GPIO_REG_EN_CTL);
+
+ if (val < 0 || !(val >> PMIC_GPIO_REG_MASTER_EN_SHIFT)) {
+ seq_puts(s, " ---");
+ } else {
+
+ if (!pad->input_enabled) {
+ ret = pmic_gpio_read(state, pad, PMIC_MPP_REG_RT_STS);
+ if (!ret) {
+ ret &= PMIC_MPP_REG_RT_STS_VAL_MASK;
+ pad->out_value = ret;
+ }
+ }
+
+ seq_printf(s, " %-4s", pad->output_enabled ? "out" : "in");
+ seq_printf(s, " %-7s", pmic_gpio_functions[pad->function]);
+ seq_printf(s, " vin-%d", pad->power_source);
+ seq_printf(s, " %-27s", biases[pad->pullup]);
+ seq_printf(s, " %-10s", buffer_types[pad->buffer_type]);
+ seq_printf(s, " %-4s", pad->out_value ? "high" : "low");
+ seq_printf(s, " %-7s", strengths[pad->strength]);
+ }
+}
+
+static const struct pinconf_ops pmic_gpio_pinconf_ops = {
+ .pin_config_group_get = pmic_gpio_config_get,
+ .pin_config_group_set = pmic_gpio_config_set,
+ .pin_config_group_dbg_show = pmic_gpio_config_dbg_show,
+};
+
+static int pmic_gpio_direction_input(struct gpio_chip *chip, unsigned pin)
+{
+ struct pmic_gpio_state *state = to_gpio_state(chip);
+ unsigned long config;
+
+ config = pinconf_to_config_packed(PIN_CONFIG_INPUT_ENABLE, 1);
+
+ return pmic_gpio_config_set(state->ctrl, pin, &config, 1);
+}
+
+static int pmic_gpio_direction_output(struct gpio_chip *chip,
+ unsigned pin, int val)
+{
+ struct pmic_gpio_state *state = to_gpio_state(chip);
+ unsigned long config;
+
+ config = pinconf_to_config_packed(PIN_CONFIG_OUTPUT, val);
+
+ return pmic_gpio_config_set(state->ctrl, pin, &config, 1);
+}
+
+static int pmic_gpio_get(struct gpio_chip *chip, unsigned pin)
+{
+ struct pmic_gpio_state *state = to_gpio_state(chip);
+ struct pmic_gpio_pad *pad;
+ int ret;
+
+ pad = state->ctrl->desc->pins[pin].drv_data;
+
+ if (!pad->is_enabled)
+ return -EINVAL;
+
+ if (pad->input_enabled) {
+ ret = pmic_gpio_read(state, pad, PMIC_MPP_REG_RT_STS);
+ if (ret < 0)
+ return ret;
+
+ pad->out_value = ret & PMIC_MPP_REG_RT_STS_VAL_MASK;
+ }
+
+ return pad->out_value;
+}
+
+static void pmic_gpio_set(struct gpio_chip *chip, unsigned pin, int value)
+{
+ struct pmic_gpio_state *state = to_gpio_state(chip);
+ unsigned long config;
+
+ config = pinconf_to_config_packed(PIN_CONFIG_OUTPUT, value);
+
+ pmic_gpio_config_set(state->ctrl, pin, &config, 1);
+}
+
+static int pmic_gpio_request(struct gpio_chip *chip, unsigned base)
+{
+ return pinctrl_request_gpio(chip->base + base);
+}
+
+static void pmic_gpio_free(struct gpio_chip *chip, unsigned base)
+{
+ pinctrl_free_gpio(chip->base + base);
+}
+
+static int pmic_gpio_of_xlate(struct gpio_chip *chip,
+ const struct of_phandle_args *gpio_desc,
+ u32 *flags)
+{
+ if (chip->of_gpio_n_cells < 2)
+ return -EINVAL;
+
+ if (flags)
+ *flags = gpio_desc->args[1];
+
+ return gpio_desc->args[0] - PMIC_GPIO_PHYSICAL_OFFSET;
+}
+
+static int pmic_gpio_to_irq(struct gpio_chip *chip, unsigned pin)
+{
+ struct pmic_gpio_state *state = to_gpio_state(chip);
+ struct pmic_gpio_pad *pad;
+
+ pad = state->ctrl->desc->pins[pin].drv_data;
+
+ return pad->irq;
+}
+
+static void pmic_gpio_dbg_show(struct seq_file *s, struct gpio_chip *chip)
+{
+ struct pmic_gpio_state *state = to_gpio_state(chip);
+ unsigned i;
+
+ for (i = 0; i < chip->ngpio; i++) {
+ pmic_gpio_config_dbg_show(state->ctrl, s, i);
+ seq_puts(s, "\n");
+ }
+}
+
+static const struct gpio_chip pmic_gpio_gpio_template = {
+ .direction_input = pmic_gpio_direction_input,
+ .direction_output = pmic_gpio_direction_output,
+ .get = pmic_gpio_get,
+ .set = pmic_gpio_set,
+ .request = pmic_gpio_request,
+ .free = pmic_gpio_free,
+ .of_xlate = pmic_gpio_of_xlate,
+ .to_irq = pmic_gpio_to_irq,
+ .dbg_show = pmic_gpio_dbg_show,
+};
+
+static int pmic_gpio_populate(struct pmic_gpio_state *state,
+ struct pmic_gpio_pad *pad)
+{
+ int type, subtype, val, dir;
+
+ type = pmic_gpio_read(state, pad, PMIC_GPIO_REG_TYPE);
+ if (type < 0)
+ return type;
+
+ if (type != PMIC_GPIO_TYPE) {
+ dev_err(state->dev, "incorrect block type 0x%x at 0x%x\n",
+ type, pad->base);
+ return -ENODEV;
+ }
+
+ subtype = pmic_gpio_read(state, pad, PMIC_GPIO_REG_SUBTYPE);
+ if (subtype < 0)
+ return subtype;
+
+ switch (subtype) {
+ case PMIC_GPIO_SUBTYPE_GPIO_4CH:
+ pad->have_buffer = true;
+ case PMIC_GPIO_SUBTYPE_GPIOC_4CH:
+ pad->num_sources = 4;
+ break;
+ case PMIC_GPIO_SUBTYPE_GPIO_8CH:
+ pad->have_buffer = true;
+ case PMIC_GPIO_SUBTYPE_GPIOC_8CH:
+ pad->num_sources = 8;
+ break;
+ default:
+ dev_err(state->dev, "unknown GPIO type 0x%x\n", subtype);
+ return -ENODEV;
+ }
+
+ val = pmic_gpio_read(state, pad, PMIC_GPIO_REG_MODE_CTL);
+ if (val < 0)
+ return val;
+
+ pad->out_value = val & PMIC_GPIO_REG_MODE_VALUE_SHIFT;
+
+ dir = val >> PMIC_GPIO_REG_MODE_DIR_SHIFT;
+ dir &= PMIC_GPIO_REG_MODE_DIR_MASK;
+ switch (dir) {
+ case 0:
+ pad->input_enabled = true;
+ pad->output_enabled = false;
+ break;
+ case 1:
+ pad->input_enabled = false;
+ pad->output_enabled = true;
+ break;
+ case 2:
+ pad->input_enabled = true;
+ pad->output_enabled = true;
+ break;
+ default:
+ dev_err(state->dev, "unknown GPIO direction\n");
+ return -ENODEV;
+ }
+
+ pad->function = val >> PMIC_GPIO_REG_MODE_FUNCTION_SHIFT;
+ pad->function &= PMIC_GPIO_REG_MODE_FUNCTION_MASK;
+
+ val = pmic_gpio_read(state, pad, PMIC_GPIO_REG_DIG_VIN_CTL);
+ if (val < 0)
+ return val;
+
+ pad->power_source = val >> PMIC_GPIO_REG_VIN_SHIFT;
+ pad->power_source &= PMIC_GPIO_REG_VIN_MASK;
+
+ val = pmic_gpio_read(state, pad, PMIC_GPIO_REG_DIG_PULL_CTL);
+ if (val < 0)
+ return val;
+
+ pad->pullup = val >> PMIC_GPIO_REG_PULL_SHIFT;
+ pad->pullup &= PMIC_GPIO_REG_PULL_MASK;
+
+ val = pmic_gpio_read(state, pad, PMIC_GPIO_REG_DIG_OUT_CTL);
+ if (val < 0)
+ return val;
+
+ pad->strength = val >> PMIC_GPIO_REG_OUT_STRENGTH_SHIFT;
+ pad->strength &= PMIC_GPIO_REG_OUT_STRENGTH_MASK;
+
+ pad->buffer_type = val >> PMIC_GPIO_REG_OUT_TYPE_SHIFT;
+ pad->buffer_type &= PMIC_GPIO_REG_OUT_TYPE_MASK;
+
+ /* Pin could be disabled with PIN_CONFIG_BIAS_HIGH_IMPEDANCE */
+ pad->is_enabled = true;
+ return 0;
+}
+
+static int pmic_gpio_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct pinctrl_pin_desc *pindesc;
+ struct pinctrl_desc *pctrldesc;
+ struct pmic_gpio_pad *pad, *pads;
+ struct pmic_gpio_state *state;
+ int ret, npins, i;
+ u32 res[2];
+
+ ret = of_property_read_u32_array(dev->of_node, "reg", res, 2);
+ if (ret < 0) {
+ dev_err(dev, "missing base address and/or range");
+ return ret;
+ }
+
+ npins = res[1] / PMIC_GPIO_ADDRESS_RANGE;
+
+ if (!npins)
+ return -EINVAL;
+
+ BUG_ON(npins > ARRAY_SIZE(pmic_gpio_groups));
+
+ state = devm_kzalloc(dev, sizeof(*state), GFP_KERNEL);
+ if (!state)
+ return -ENOMEM;
+
+ platform_set_drvdata(pdev, state);
+
+ state->dev = &pdev->dev;
+ state->map = dev_get_regmap(dev->parent, NULL);
+
+ pindesc = devm_kcalloc(dev, npins, sizeof(*pindesc), GFP_KERNEL);
+ if (!pindesc)
+ return -ENOMEM;
+
+ pads = devm_kcalloc(dev, npins, sizeof(*pads), GFP_KERNEL);
+ if (!pads)
+ return -ENOMEM;
+
+ pctrldesc = devm_kzalloc(dev, sizeof(*pctrldesc), GFP_KERNEL);
+ if (!pctrldesc)
+ return -ENOMEM;
+
+ pctrldesc->pctlops = &pmic_gpio_pinctrl_ops;
+ pctrldesc->pmxops = &pmic_gpio_pinmux_ops;
+ pctrldesc->confops = &pmic_gpio_pinconf_ops;
+ pctrldesc->owner = THIS_MODULE;
+ pctrldesc->name = dev_name(dev);
+ pctrldesc->pins = pindesc;
+ pctrldesc->npins = npins;
+
+ for (i = 0; i < npins; i++, pindesc++) {
+ pad = &pads[i];
+ pindesc->drv_data = pad;
+ pindesc->number = i;
+ pindesc->name = pmic_gpio_groups[i];
+
+ pad->irq = platform_get_irq(pdev, i);
+ if (pad->irq < 0)
+ return pad->irq;
+
+ pad->base = res[0] + i * PMIC_GPIO_ADDRESS_RANGE;
+
+ ret = pmic_gpio_populate(state, pad);
+ if (ret < 0)
+ return ret;
+ }
+
+ state->chip = pmic_gpio_gpio_template;
+ state->chip.dev = dev;
+ state->chip.base = -1;
+ state->chip.ngpio = npins;
+ state->chip.label = dev_name(dev);
+ state->chip.of_gpio_n_cells = 2;
+ state->chip.can_sleep = false;
+
+ state->ctrl = pinctrl_register(pctrldesc, dev, state);
+ if (!state->ctrl)
+ return -ENODEV;
+
+ ret = gpiochip_add(&state->chip);
+ if (ret) {
+ dev_err(state->dev, "can't add gpio chip\n");
+ goto err_chip;
+ }
+
+ ret = gpiochip_add_pin_range(&state->chip, dev_name(dev), 0, 0, npins);
+ if (ret) {
+ dev_err(dev, "failed to add pin range\n");
+ goto err_range;
+ }
+
+ return 0;
+
+err_range:
+ gpiochip_remove(&state->chip);
+err_chip:
+ pinctrl_unregister(state->ctrl);
+ return ret;
+}
+
+static int pmic_gpio_remove(struct platform_device *pdev)
+{
+ struct pmic_gpio_state *state = platform_get_drvdata(pdev);
+
+ gpiochip_remove(&state->chip);
+ pinctrl_unregister(state->ctrl);
+ return 0;
+}
+
+static const struct of_device_id pmic_gpio_of_match[] = {
+ { .compatible = "qcom,pm8941-gpio" }, /* 36 GPIO's */
+ { .compatible = "qcom,pma8084-gpio" }, /* 22 GPIO's */
+ { },
+};
+
+MODULE_DEVICE_TABLE(of, pmic_gpio_of_match);
+
+static struct platform_driver pmic_gpio_driver = {
+ .driver = {
+ .name = "qcom-spmi-gpio",
+ .of_match_table = pmic_gpio_of_match,
+ },
+ .probe = pmic_gpio_probe,
+ .remove = pmic_gpio_remove,
+};
+
+module_platform_driver(pmic_gpio_driver);
+
+MODULE_AUTHOR("Ivan T. Ivanov <iivanov@mm-sol.com>");
+MODULE_DESCRIPTION("Qualcomm SPMI PMIC GPIO pin control driver");
+MODULE_ALIAS("platform:qcom-spmi-gpio");
+MODULE_LICENSE("GPL v2");
--
1.9.1
^ permalink raw reply related [flat|nested] 6+ messages in thread* [PATCH v6 4/4] pinctrl: Qualcomm SPMI PMIC MPP pin controller driver
2014-10-22 9:58 [PATCH v6 0/4] Qualcomm SPMI PMIC pin controller drivers Ivan T. Ivanov
` (2 preceding siblings ...)
2014-10-22 9:58 ` [PATCH v6 3/4] pinctrl: Qualcomm SPMI PMIC GPIO pin controller driver Ivan T. Ivanov
@ 2014-10-22 9:58 ` Ivan T. Ivanov
2014-10-28 16:29 ` [PATCH v6 0/4] Qualcomm SPMI PMIC pin controller drivers Linus Walleij
4 siblings, 0 replies; 6+ messages in thread
From: Ivan T. Ivanov @ 2014-10-22 9:58 UTC (permalink / raw)
To: Linus Walleij, Grant Likely, Rob Herring
Cc: Ivan T. Ivanov, Bjorn Andersson, Georgi Djakov, Andy Gross,
linux-kernel, devicetree, linux-arm-msm
This is the pinctrl, pinmux, pinconf and gpiolib driver for the
Qualcomm MPP sub-function blocks found in the PMIC chips.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
---
drivers/pinctrl/qcom/Makefile | 1 +
drivers/pinctrl/qcom/pinctrl-spmi-mpp.c | 949 ++++++++++++++++++++++++++++++++
2 files changed, 950 insertions(+)
create mode 100644 drivers/pinctrl/qcom/pinctrl-spmi-mpp.c
diff --git a/drivers/pinctrl/qcom/Makefile b/drivers/pinctrl/qcom/Makefile
index 9b49c65a..bfd79af 100644
--- a/drivers/pinctrl/qcom/Makefile
+++ b/drivers/pinctrl/qcom/Makefile
@@ -6,3 +6,4 @@ obj-$(CONFIG_PINCTRL_IPQ8064) += pinctrl-ipq8064.o
obj-$(CONFIG_PINCTRL_MSM8960) += pinctrl-msm8960.o
obj-$(CONFIG_PINCTRL_MSM8X74) += pinctrl-msm8x74.o
obj-$(CONFIG_PINCTRL_QCOM_SPMI_PMIC) += pinctrl-spmi-gpio.o
+obj-$(CONFIG_PINCTRL_QCOM_SPMI_PMIC) += pinctrl-spmi-mpp.o
diff --git a/drivers/pinctrl/qcom/pinctrl-spmi-mpp.c b/drivers/pinctrl/qcom/pinctrl-spmi-mpp.c
new file mode 100644
index 0000000..a8924db
--- /dev/null
+++ b/drivers/pinctrl/qcom/pinctrl-spmi-mpp.c
@@ -0,0 +1,949 @@
+/*
+ * Copyright (c) 2012-2014, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/gpio.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/pinctrl/pinconf-generic.h>
+#include <linux/pinctrl/pinconf.h>
+#include <linux/pinctrl/pinmux.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+
+#include <dt-bindings/pinctrl/qcom,pmic-mpp.h>
+
+#include "../core.h"
+#include "../pinctrl-utils.h"
+
+#define PMIC_MPP_ADDRESS_RANGE 0x100
+
+/*
+ * Pull Up Values - it indicates whether a pull-up should be
+ * applied for bidirectional mode only. The hardware ignores the
+ * configuration when operating in other modes.
+ */
+#define PMIC_MPP_PULL_UP_0P6KOHM 0
+#define PMIC_MPP_PULL_UP_10KOHM 1
+#define PMIC_MPP_PULL_UP_30KOHM 2
+#define PMIC_MPP_PULL_UP_OPEN 3
+
+/* type registers base address bases */
+#define PMIC_MPP_REG_TYPE 0x4
+#define PMIC_MPP_REG_SUBTYPE 0x5
+
+/* mpp peripheral type and subtype values */
+#define PMIC_MPP_TYPE 0x11
+#define PMIC_MPP_SUBTYPE_4CH_NO_ANA_OUT 0x3
+#define PMIC_MPP_SUBTYPE_ULT_4CH_NO_ANA_OUT 0x4
+#define PMIC_MPP_SUBTYPE_4CH_NO_SINK 0x5
+#define PMIC_MPP_SUBTYPE_ULT_4CH_NO_SINK 0x6
+#define PMIC_MPP_SUBTYPE_4CH_FULL_FUNC 0x7
+#define PMIC_MPP_SUBTYPE_8CH_FULL_FUNC 0xf
+
+#define PMIC_MPP_REG_RT_STS 0x10
+#define PMIC_MPP_REG_RT_STS_VAL_MASK 0x1
+
+/* control register base address bases */
+#define PMIC_MPP_REG_MODE_CTL 0x40
+#define PMIC_MPP_REG_DIG_VIN_CTL 0x41
+#define PMIC_MPP_REG_DIG_PULL_CTL 0x42
+#define PMIC_MPP_REG_DIG_IN_CTL 0x43
+#define PMIC_MPP_REG_EN_CTL 0x46
+#define PMIC_MPP_REG_AIN_CTL 0x4a
+
+/* PMIC_MPP_REG_MODE_CTL */
+#define PMIC_MPP_REG_MODE_VALUE_MASK 0x1
+#define PMIC_MPP_REG_MODE_FUNCTION_SHIFT 1
+#define PMIC_MPP_REG_MODE_FUNCTION_MASK 0x7
+#define PMIC_MPP_REG_MODE_DIR_SHIFT 4
+#define PMIC_MPP_REG_MODE_DIR_MASK 0x7
+
+/* PMIC_MPP_REG_DIG_VIN_CTL */
+#define PMIC_MPP_REG_VIN_SHIFT 0
+#define PMIC_MPP_REG_VIN_MASK 0x7
+
+/* PMIC_MPP_REG_DIG_PULL_CTL */
+#define PMIC_MPP_REG_PULL_SHIFT 0
+#define PMIC_MPP_REG_PULL_MASK 0x7
+
+/* PMIC_MPP_REG_EN_CTL */
+#define PMIC_MPP_REG_MASTER_EN_SHIFT 7
+
+/* PMIC_MPP_REG_AIN_CTL */
+#define PMIC_MPP_REG_AIN_ROUTE_SHIFT 0
+#define PMIC_MPP_REG_AIN_ROUTE_MASK 0x7
+
+#define PMIC_MPP_PHYSICAL_OFFSET 1
+
+/* Qualcomm specific pin configurations */
+#define PMIC_MPP_CONF_AMUX_ROUTE (PIN_CONFIG_END + 1)
+#define PMIC_MPP_CONF_ANALOG_MODE (PIN_CONFIG_END + 2)
+
+/**
+ * struct pmic_mpp_pad - keep current MPP settings
+ * @base: Address base in SPMI device.
+ * @irq: IRQ number which this MPP generate.
+ * @is_enabled: Set to false when MPP should be put in high Z state.
+ * @out_value: Cached pin output value.
+ * @output_enabled: Set to true if MPP output logic is enabled.
+ * @input_enabled: Set to true if MPP input buffer logic is enabled.
+ * @analog_mode: Set to true when MPP should operate in Analog Input, Analog
+ * Output or Bidirectional Analog mode.
+ * @num_sources: Number of power-sources supported by this MPP.
+ * @power_source: Current power-source used.
+ * @amux_input: Set the source for analog input.
+ * @pullup: Pullup resistor value. Valid in Bidirectional mode only.
+ * @function: See pmic_mpp_functions[].
+ */
+struct pmic_mpp_pad {
+ u16 base;
+ int irq;
+ bool is_enabled;
+ bool out_value;
+ bool output_enabled;
+ bool input_enabled;
+ bool analog_mode;
+ unsigned int num_sources;
+ unsigned int power_source;
+ unsigned int amux_input;
+ unsigned int pullup;
+ unsigned int function;
+};
+
+struct pmic_mpp_state {
+ struct device *dev;
+ struct regmap *map;
+ struct pinctrl_dev *ctrl;
+ struct gpio_chip chip;
+};
+
+struct pmic_mpp_bindings {
+ const char *property;
+ unsigned param;
+};
+
+static struct pmic_mpp_bindings pmic_mpp_bindings[] = {
+ {"qcom,amux-route", PMIC_MPP_CONF_AMUX_ROUTE},
+ {"qcom,analog-mode", PMIC_MPP_CONF_ANALOG_MODE},
+};
+
+static const char *const pmic_mpp_groups[] = {
+ "mpp1", "mpp2", "mpp3", "mpp4", "mpp5", "mpp6", "mpp7", "mpp8",
+};
+
+static const char *const pmic_mpp_functions[] = {
+ PMIC_MPP_FUNC_NORMAL, PMIC_MPP_FUNC_PAIRED,
+ "reserved1", "reserved2",
+ PMIC_MPP_FUNC_DTEST1, PMIC_MPP_FUNC_DTEST2,
+ PMIC_MPP_FUNC_DTEST3, PMIC_MPP_FUNC_DTEST4,
+};
+
+static inline struct pmic_mpp_state *to_mpp_state(struct gpio_chip *chip)
+{
+ return container_of(chip, struct pmic_mpp_state, chip);
+};
+
+static int pmic_mpp_read(struct pmic_mpp_state *state,
+ struct pmic_mpp_pad *pad, unsigned int addr)
+{
+ unsigned int val;
+ int ret;
+
+ ret = regmap_read(state->map, pad->base + addr, &val);
+ if (ret < 0)
+ dev_err(state->dev, "read 0x%x failed\n", addr);
+ else
+ ret = val;
+
+ return ret;
+}
+
+static int pmic_mpp_write(struct pmic_mpp_state *state,
+ struct pmic_mpp_pad *pad, unsigned int addr,
+ unsigned int val)
+{
+ int ret;
+
+ ret = regmap_write(state->map, pad->base + addr, val);
+ if (ret < 0)
+ dev_err(state->dev, "write 0x%x failed\n", addr);
+
+ return ret;
+}
+
+static int pmic_mpp_get_groups_count(struct pinctrl_dev *pctldev)
+{
+ /* Every PIN is a group */
+ return pctldev->desc->npins;
+}
+
+static const char *pmic_mpp_get_group_name(struct pinctrl_dev *pctldev,
+ unsigned pin)
+{
+ return pctldev->desc->pins[pin].name;
+}
+
+static int pmic_mpp_get_group_pins(struct pinctrl_dev *pctldev,
+ unsigned pin,
+ const unsigned **pins, unsigned *num_pins)
+{
+ *pins = &pctldev->desc->pins[pin].number;
+ *num_pins = 1;
+ return 0;
+}
+
+static int pmic_mpp_parse_dt_config(struct device_node *np,
+ struct pinctrl_dev *pctldev,
+ unsigned long **configs,
+ unsigned int *nconfs)
+{
+ struct pmic_mpp_bindings *par;
+ unsigned long cfg;
+ int ret, i;
+ u32 val;
+
+ for (i = 0; i < ARRAY_SIZE(pmic_mpp_bindings); i++) {
+ par = &pmic_mpp_bindings[i];
+ ret = of_property_read_u32(np, par->property, &val);
+
+ /* property not found */
+ if (ret == -EINVAL)
+ continue;
+
+ /* use zero as default value, when no value is specified */
+ if (ret)
+ val = 0;
+
+ dev_dbg(pctldev->dev, "found %s with value %u\n",
+ par->property, val);
+
+ cfg = pinconf_to_config_packed(par->param, val);
+
+ ret = pinctrl_utils_add_config(pctldev, configs, nconfs, cfg);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
+static int pmic_mpp_dt_subnode_to_map(struct pinctrl_dev *pctldev,
+ struct device_node *np,
+ struct pinctrl_map **map,
+ unsigned *reserv, unsigned *nmaps,
+ enum pinctrl_map_type type)
+{
+ unsigned long *configs = NULL;
+ unsigned nconfs = 0;
+ struct property *prop;
+ const char *group;
+ int ret;
+
+ ret = pmic_mpp_parse_dt_config(np, pctldev, &configs, &nconfs);
+ if (ret < 0)
+ return ret;
+
+ if (!nconfs)
+ return 0;
+
+ ret = of_property_count_strings(np, "pins");
+ if (ret < 0)
+ goto exit;
+
+ ret = pinctrl_utils_reserve_map(pctldev, map, reserv, nmaps, ret);
+ if (ret < 0)
+ goto exit;
+
+ of_property_for_each_string(np, "pins", prop, group) {
+ ret = pinctrl_utils_add_map_configs(pctldev, map,
+ reserv, nmaps, group,
+ configs, nconfs, type);
+ if (ret < 0)
+ break;
+ }
+exit:
+ kfree(configs);
+ return ret;
+}
+
+static int pmic_mpp_dt_node_to_map(struct pinctrl_dev *pctldev,
+ struct device_node *np_config,
+ struct pinctrl_map **map, unsigned *nmaps)
+{
+ struct device_node *np;
+ enum pinctrl_map_type type;
+ unsigned reserv;
+ int ret;
+
+ ret = 0;
+ *map = NULL;
+ *nmaps = 0;
+ reserv = 0;
+ type = PIN_MAP_TYPE_CONFIGS_GROUP;
+
+ for_each_child_of_node(np_config, np) {
+ ret = pinconf_generic_dt_subnode_to_map(pctldev, np, map,
+ &reserv, nmaps, type);
+ if (ret)
+ break;
+
+ ret = pmic_mpp_dt_subnode_to_map(pctldev, np, map, &reserv,
+ nmaps, type);
+ if (ret)
+ break;
+ }
+
+ if (ret < 0)
+ pinctrl_utils_dt_free_map(pctldev, *map, *nmaps);
+
+ return ret;
+}
+
+static const struct pinctrl_ops pmic_mpp_pinctrl_ops = {
+ .get_groups_count = pmic_mpp_get_groups_count,
+ .get_group_name = pmic_mpp_get_group_name,
+ .get_group_pins = pmic_mpp_get_group_pins,
+ .dt_node_to_map = pmic_mpp_dt_node_to_map,
+ .dt_free_map = pinctrl_utils_dt_free_map,
+};
+
+static int pmic_mpp_get_functions_count(struct pinctrl_dev *pctldev)
+{
+ return ARRAY_SIZE(pmic_mpp_functions);
+}
+
+static const char *pmic_mpp_get_function_name(struct pinctrl_dev *pctldev,
+ unsigned function)
+{
+ return pmic_mpp_functions[function];
+}
+
+static int pmic_mpp_get_function_groups(struct pinctrl_dev *pctldev,
+ unsigned function,
+ const char *const **groups,
+ unsigned *const num_qgroups)
+{
+ *groups = pmic_mpp_groups;
+ *num_qgroups = pctldev->desc->npins;
+ return 0;
+}
+
+static int pmic_mpp_set_mux(struct pinctrl_dev *pctldev, unsigned function,
+ unsigned pin)
+{
+ struct pmic_mpp_state *state = pinctrl_dev_get_drvdata(pctldev);
+ struct pmic_mpp_pad *pad;
+ unsigned int val;
+ int ret;
+
+ pad = pctldev->desc->pins[pin].drv_data;
+
+ pad->function = function;
+
+ if (!pad->analog_mode) {
+ val = 0; /* just digital input */
+ if (pad->output_enabled) {
+ if (pad->input_enabled)
+ val = 2; /* digital input and output */
+ else
+ val = 1; /* just digital output */
+ }
+ } else {
+ val = 4; /* just analog input */
+ if (pad->output_enabled) {
+ if (pad->input_enabled)
+ val = 3; /* analog input and output */
+ else
+ val = 5; /* just analog output */
+ }
+ }
+
+ val |= pad->function << PMIC_MPP_REG_MODE_FUNCTION_SHIFT;
+ val |= pad->out_value & PMIC_MPP_REG_MODE_VALUE_MASK;
+
+ ret = pmic_mpp_write(state, pad, PMIC_MPP_REG_MODE_CTL, val);
+ if (ret < 0)
+ return ret;
+
+ val = pad->is_enabled << PMIC_MPP_REG_MASTER_EN_SHIFT;
+
+ return pmic_mpp_write(state, pad, PMIC_MPP_REG_EN_CTL, val);
+}
+
+static const struct pinmux_ops pmic_mpp_pinmux_ops = {
+ .get_functions_count = pmic_mpp_get_functions_count,
+ .get_function_name = pmic_mpp_get_function_name,
+ .get_function_groups = pmic_mpp_get_function_groups,
+ .set_mux = pmic_mpp_set_mux,
+};
+
+static int pmic_mpp_config_get(struct pinctrl_dev *pctldev,
+ unsigned int pin, unsigned long *config)
+{
+ unsigned param = pinconf_to_config_param(*config);
+ struct pmic_mpp_pad *pad;
+ unsigned arg = 0;
+
+ pad = pctldev->desc->pins[pin].drv_data;
+
+ switch (param) {
+ case PIN_CONFIG_BIAS_DISABLE:
+ arg = pad->pullup == PMIC_MPP_PULL_UP_OPEN;
+ break;
+ case PIN_CONFIG_BIAS_PULL_UP:
+ switch (pad->pullup) {
+ case PMIC_MPP_PULL_UP_OPEN:
+ arg = 0;
+ break;
+ case PMIC_MPP_PULL_UP_0P6KOHM:
+ arg = 600;
+ break;
+ case PMIC_MPP_PULL_UP_10KOHM:
+ arg = 10000;
+ break;
+ case PMIC_MPP_PULL_UP_30KOHM:
+ arg = 30000;
+ break;
+ default:
+ return -EINVAL;
+ }
+ break;
+ case PIN_CONFIG_BIAS_HIGH_IMPEDANCE:
+ arg = !pad->is_enabled;
+ break;
+ case PIN_CONFIG_POWER_SOURCE:
+ arg = pad->power_source;
+ break;
+ case PIN_CONFIG_INPUT_ENABLE:
+ arg = pad->input_enabled;
+ break;
+ case PIN_CONFIG_OUTPUT:
+ arg = pad->out_value;
+ break;
+ case PMIC_MPP_CONF_AMUX_ROUTE:
+ arg = pad->amux_input;
+ break;
+ case PMIC_MPP_CONF_ANALOG_MODE:
+ arg = pad->analog_mode;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ /* Convert register value to pinconf value */
+ *config = pinconf_to_config_packed(param, arg);
+ return 0;
+}
+
+static int pmic_mpp_config_set(struct pinctrl_dev *pctldev, unsigned int pin,
+ unsigned long *configs, unsigned nconfs)
+{
+ struct pmic_mpp_state *state = pinctrl_dev_get_drvdata(pctldev);
+ struct pmic_mpp_pad *pad;
+ unsigned param, arg;
+ unsigned int val;
+ int i, ret;
+
+ pad = pctldev->desc->pins[pin].drv_data;
+
+ for (i = 0; i < nconfs; i++) {
+ param = pinconf_to_config_param(configs[i]);
+ arg = pinconf_to_config_argument(configs[i]);
+
+ switch (param) {
+ case PIN_CONFIG_BIAS_DISABLE:
+ pad->pullup = PMIC_MPP_PULL_UP_OPEN;
+ break;
+ case PIN_CONFIG_BIAS_PULL_UP:
+ switch (arg) {
+ case 600:
+ pad->pullup = PMIC_MPP_PULL_UP_0P6KOHM;
+ break;
+ case 10000:
+ pad->pullup = PMIC_MPP_PULL_UP_10KOHM;
+ break;
+ case 30000:
+ pad->pullup = PMIC_MPP_PULL_UP_30KOHM;
+ break;
+ default:
+ return -EINVAL;
+ }
+ break;
+ case PIN_CONFIG_BIAS_HIGH_IMPEDANCE:
+ pad->is_enabled = false;
+ break;
+ case PIN_CONFIG_POWER_SOURCE:
+ if (arg >= pad->num_sources)
+ return -EINVAL;
+ pad->power_source = arg;
+ break;
+ case PIN_CONFIG_INPUT_ENABLE:
+ pad->input_enabled = arg ? true : false;
+ break;
+ case PIN_CONFIG_OUTPUT:
+ pad->output_enabled = true;
+ pad->out_value = arg;
+ break;
+ case PMIC_MPP_CONF_AMUX_ROUTE:
+ if (arg >= PMIC_MPP_AMUX_ROUTE_ABUS4)
+ return -EINVAL;
+ pad->amux_input = arg;
+ break;
+ case PMIC_MPP_CONF_ANALOG_MODE:
+ pad->analog_mode = true;
+ break;
+ default:
+ return -EINVAL;
+ }
+ }
+
+ val = pad->power_source << PMIC_MPP_REG_VIN_SHIFT;
+
+ ret = pmic_mpp_write(state, pad, PMIC_MPP_REG_DIG_VIN_CTL, val);
+ if (ret < 0)
+ return ret;
+
+ val = pad->pullup << PMIC_MPP_REG_PULL_SHIFT;
+
+ ret = pmic_mpp_write(state, pad, PMIC_MPP_REG_DIG_PULL_CTL, val);
+ if (ret < 0)
+ return ret;
+
+ val = pad->amux_input & PMIC_MPP_REG_AIN_ROUTE_MASK;
+
+ ret = pmic_mpp_write(state, pad, PMIC_MPP_REG_AIN_CTL, val);
+ if (ret < 0)
+ return ret;
+
+ if (!pad->analog_mode) {
+ val = 0; /* just digital input */
+ if (pad->output_enabled) {
+ if (pad->input_enabled)
+ val = 2; /* digital input and output */
+ else
+ val = 1; /* just digital output */
+ }
+ } else {
+ val = 4; /* just analog input */
+ if (pad->output_enabled) {
+ if (pad->input_enabled)
+ val = 3; /* analog input and output */
+ else
+ val = 5; /* just analog output */
+ }
+ }
+
+ val = val << PMIC_MPP_REG_MODE_DIR_SHIFT;
+ val |= pad->function << PMIC_MPP_REG_MODE_FUNCTION_SHIFT;
+ val |= pad->out_value & PMIC_MPP_REG_MODE_VALUE_MASK;
+
+ return pmic_mpp_write(state, pad, PMIC_MPP_REG_MODE_CTL, val);
+}
+
+static void pmic_mpp_config_dbg_show(struct pinctrl_dev *pctldev,
+ struct seq_file *s, unsigned pin)
+{
+ struct pmic_mpp_state *state = pinctrl_dev_get_drvdata(pctldev);
+ struct pmic_mpp_pad *pad;
+ int ret, val;
+
+ static const char *const biases[] = {
+ "0.6kOhm", "10kOhm", "30kOhm", "Disabled"
+ };
+
+
+ pad = pctldev->desc->pins[pin].drv_data;
+
+ seq_printf(s, " mpp%-2d:", pin + PMIC_MPP_PHYSICAL_OFFSET);
+
+ val = pmic_mpp_read(state, pad, PMIC_MPP_REG_EN_CTL);
+
+ if (val < 0 || !(val >> PMIC_MPP_REG_MASTER_EN_SHIFT)) {
+ seq_puts(s, " ---");
+ } else {
+
+ if (pad->input_enabled) {
+ ret = pmic_mpp_read(state, pad, PMIC_MPP_REG_RT_STS);
+ if (!ret) {
+ ret &= PMIC_MPP_REG_RT_STS_VAL_MASK;
+ pad->out_value = ret;
+ }
+ }
+
+ seq_printf(s, " %-4s", pad->output_enabled ? "out" : "in");
+ seq_printf(s, " %-4s", pad->analog_mode ? "ana" : "dig");
+ seq_printf(s, " %-7s", pmic_mpp_functions[pad->function]);
+ seq_printf(s, " vin-%d", pad->power_source);
+ seq_printf(s, " %-8s", biases[pad->pullup]);
+ seq_printf(s, " %-4s", pad->out_value ? "high" : "low");
+ }
+}
+
+static const struct pinconf_ops pmic_mpp_pinconf_ops = {
+ .pin_config_group_get = pmic_mpp_config_get,
+ .pin_config_group_set = pmic_mpp_config_set,
+ .pin_config_group_dbg_show = pmic_mpp_config_dbg_show,
+};
+
+static int pmic_mpp_direction_input(struct gpio_chip *chip, unsigned pin)
+{
+ struct pmic_mpp_state *state = to_mpp_state(chip);
+ unsigned long config;
+
+ config = pinconf_to_config_packed(PIN_CONFIG_INPUT_ENABLE, 1);
+
+ return pmic_mpp_config_set(state->ctrl, pin, &config, 1);
+}
+
+static int pmic_mpp_direction_output(struct gpio_chip *chip,
+ unsigned pin, int val)
+{
+ struct pmic_mpp_state *state = to_mpp_state(chip);
+ unsigned long config;
+
+ config = pinconf_to_config_packed(PIN_CONFIG_OUTPUT, val);
+
+ return pmic_mpp_config_set(state->ctrl, pin, &config, 1);
+}
+
+static int pmic_mpp_get(struct gpio_chip *chip, unsigned pin)
+{
+ struct pmic_mpp_state *state = to_mpp_state(chip);
+ struct pmic_mpp_pad *pad;
+ int ret;
+
+ pad = state->ctrl->desc->pins[pin].drv_data;
+
+ if (pad->input_enabled) {
+ ret = pmic_mpp_read(state, pad, PMIC_MPP_REG_RT_STS);
+ if (ret < 0)
+ return ret;
+
+ pad->out_value = ret & PMIC_MPP_REG_RT_STS_VAL_MASK;
+ }
+
+ return pad->out_value;
+}
+
+static void pmic_mpp_set(struct gpio_chip *chip, unsigned pin, int value)
+{
+ struct pmic_mpp_state *state = to_mpp_state(chip);
+ unsigned long config;
+
+ config = pinconf_to_config_packed(PIN_CONFIG_OUTPUT, value);
+
+ pmic_mpp_config_set(state->ctrl, pin, &config, 1);
+}
+
+static int pmic_mpp_request(struct gpio_chip *chip, unsigned base)
+{
+ return pinctrl_request_gpio(chip->base + base);
+}
+
+static void pmic_mpp_free(struct gpio_chip *chip, unsigned base)
+{
+ pinctrl_free_gpio(chip->base + base);
+}
+
+static int pmic_mpp_of_xlate(struct gpio_chip *chip,
+ const struct of_phandle_args *gpio_desc,
+ u32 *flags)
+{
+ if (chip->of_gpio_n_cells < 2)
+ return -EINVAL;
+
+ if (flags)
+ *flags = gpio_desc->args[1];
+
+ return gpio_desc->args[0] - PMIC_MPP_PHYSICAL_OFFSET;
+}
+
+static int pmic_mpp_to_irq(struct gpio_chip *chip, unsigned pin)
+{
+ struct pmic_mpp_state *state = to_mpp_state(chip);
+ struct pmic_mpp_pad *pad;
+
+ pad = state->ctrl->desc->pins[pin].drv_data;
+
+ return pad->irq;
+}
+
+static void pmic_mpp_dbg_show(struct seq_file *s, struct gpio_chip *chip)
+{
+ struct pmic_mpp_state *state = to_mpp_state(chip);
+ unsigned i;
+
+ for (i = 0; i < chip->ngpio; i++) {
+ pmic_mpp_config_dbg_show(state->ctrl, s, i);
+ seq_puts(s, "\n");
+ }
+}
+
+static const struct gpio_chip pmic_mpp_gpio_template = {
+ .direction_input = pmic_mpp_direction_input,
+ .direction_output = pmic_mpp_direction_output,
+ .get = pmic_mpp_get,
+ .set = pmic_mpp_set,
+ .request = pmic_mpp_request,
+ .free = pmic_mpp_free,
+ .of_xlate = pmic_mpp_of_xlate,
+ .to_irq = pmic_mpp_to_irq,
+ .dbg_show = pmic_mpp_dbg_show,
+};
+
+static int pmic_mpp_populate(struct pmic_mpp_state *state,
+ struct pmic_mpp_pad *pad)
+{
+ int type, subtype, val, dir;
+
+ type = pmic_mpp_read(state, pad, PMIC_MPP_REG_TYPE);
+ if (type < 0)
+ return type;
+
+ if (type != PMIC_MPP_TYPE) {
+ dev_err(state->dev, "incorrect block type 0x%x at 0x%x\n",
+ type, pad->base);
+ return -ENODEV;
+ }
+
+ subtype = pmic_mpp_read(state, pad, PMIC_MPP_REG_SUBTYPE);
+ if (subtype < 0)
+ return subtype;
+
+ switch (subtype) {
+ case PMIC_MPP_SUBTYPE_4CH_NO_ANA_OUT:
+ case PMIC_MPP_SUBTYPE_ULT_4CH_NO_ANA_OUT:
+ case PMIC_MPP_SUBTYPE_4CH_NO_SINK:
+ case PMIC_MPP_SUBTYPE_ULT_4CH_NO_SINK:
+ case PMIC_MPP_SUBTYPE_4CH_FULL_FUNC:
+ pad->num_sources = 4;
+ break;
+ case PMIC_MPP_SUBTYPE_8CH_FULL_FUNC:
+ pad->num_sources = 8;
+ break;
+ default:
+ dev_err(state->dev, "unknown MPP type 0x%x at 0x%x\n",
+ subtype, pad->base);
+ return -ENODEV;
+ }
+
+ val = pmic_mpp_read(state, pad, PMIC_MPP_REG_MODE_CTL);
+ if (val < 0)
+ return val;
+
+ pad->out_value = val & PMIC_MPP_REG_MODE_VALUE_MASK;
+
+ dir = val >> PMIC_MPP_REG_MODE_DIR_SHIFT;
+ dir &= PMIC_MPP_REG_MODE_DIR_MASK;
+
+ switch (dir) {
+ case 0:
+ pad->input_enabled = true;
+ pad->output_enabled = false;
+ pad->analog_mode = false;
+ break;
+ case 1:
+ pad->input_enabled = false;
+ pad->output_enabled = true;
+ pad->analog_mode = false;
+ break;
+ case 2:
+ pad->input_enabled = true;
+ pad->output_enabled = true;
+ pad->analog_mode = false;
+ break;
+ case 3:
+ pad->input_enabled = true;
+ pad->output_enabled = true;
+ pad->analog_mode = true;
+ break;
+ case 4:
+ pad->input_enabled = true;
+ pad->output_enabled = false;
+ pad->analog_mode = true;
+ break;
+ case 5:
+ pad->input_enabled = false;
+ pad->output_enabled = true;
+ pad->analog_mode = true;
+ break;
+ default:
+ dev_err(state->dev, "unknown MPP direction\n");
+ return -ENODEV;
+ }
+
+ pad->function = val >> PMIC_MPP_REG_MODE_FUNCTION_SHIFT;
+ pad->function &= PMIC_MPP_REG_MODE_FUNCTION_MASK;
+
+ val = pmic_mpp_read(state, pad, PMIC_MPP_REG_DIG_VIN_CTL);
+ if (val < 0)
+ return val;
+
+ pad->power_source = val >> PMIC_MPP_REG_VIN_SHIFT;
+ pad->power_source &= PMIC_MPP_REG_VIN_MASK;
+
+ val = pmic_mpp_read(state, pad, PMIC_MPP_REG_DIG_PULL_CTL);
+ if (val < 0)
+ return val;
+
+ pad->pullup = val >> PMIC_MPP_REG_PULL_SHIFT;
+ pad->pullup &= PMIC_MPP_REG_PULL_MASK;
+
+ val = pmic_mpp_read(state, pad, PMIC_MPP_REG_AIN_CTL);
+ if (val < 0)
+ return val;
+
+ pad->amux_input = val >> PMIC_MPP_REG_AIN_ROUTE_SHIFT;
+ pad->amux_input &= PMIC_MPP_REG_AIN_ROUTE_MASK;
+
+ /* Pin could be disabled with PIN_CONFIG_BIAS_HIGH_IMPEDANCE */
+ pad->is_enabled = true;
+ return 0;
+}
+
+static int pmic_mpp_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct pinctrl_pin_desc *pindesc;
+ struct pinctrl_desc *pctrldesc;
+ struct pmic_mpp_pad *pad, *pads;
+ struct pmic_mpp_state *state;
+ int ret, npins, i;
+ u32 res[2];
+
+ ret = of_property_read_u32_array(dev->of_node, "reg", res, 2);
+ if (ret < 0) {
+ dev_err(dev, "missing base address and/or range");
+ return ret;
+ }
+
+ npins = res[1] / PMIC_MPP_ADDRESS_RANGE;
+ if (!npins)
+ return -EINVAL;
+
+ BUG_ON(npins > ARRAY_SIZE(pmic_mpp_groups));
+
+ state = devm_kzalloc(dev, sizeof(*state), GFP_KERNEL);
+ if (!state)
+ return -ENOMEM;
+
+ platform_set_drvdata(pdev, state);
+
+ state->dev = &pdev->dev;
+ state->map = dev_get_regmap(dev->parent, NULL);
+
+ pindesc = devm_kcalloc(dev, npins, sizeof(*pindesc), GFP_KERNEL);
+ if (!pindesc)
+ return -ENOMEM;
+
+ pads = devm_kcalloc(dev, npins, sizeof(*pads), GFP_KERNEL);
+ if (!pads)
+ return -ENOMEM;
+
+ pctrldesc = devm_kzalloc(dev, sizeof(*pctrldesc), GFP_KERNEL);
+ if (!pctrldesc)
+ return -ENOMEM;
+
+ pctrldesc->pctlops = &pmic_mpp_pinctrl_ops;
+ pctrldesc->pmxops = &pmic_mpp_pinmux_ops;
+ pctrldesc->confops = &pmic_mpp_pinconf_ops;
+ pctrldesc->owner = THIS_MODULE;
+ pctrldesc->name = dev_name(dev);
+ pctrldesc->pins = pindesc;
+ pctrldesc->npins = npins;
+
+ for (i = 0; i < npins; i++, pindesc++) {
+ pad = &pads[i];
+ pindesc->drv_data = pad;
+ pindesc->number = i;
+ pindesc->name = pmic_mpp_groups[i];
+
+ pad->irq = platform_get_irq(pdev, i);
+ if (pad->irq < 0)
+ return pad->irq;
+
+ pad->base = res[0] + i * PMIC_MPP_ADDRESS_RANGE;
+
+ ret = pmic_mpp_populate(state, pad);
+ if (ret < 0)
+ return ret;
+ }
+
+ state->chip = pmic_mpp_gpio_template;
+ state->chip.dev = dev;
+ state->chip.base = -1;
+ state->chip.ngpio = npins;
+ state->chip.label = dev_name(dev);
+ state->chip.of_gpio_n_cells = 2;
+ state->chip.can_sleep = false;
+
+ state->ctrl = pinctrl_register(pctrldesc, dev, state);
+ if (!state->ctrl)
+ return -ENODEV;
+
+ ret = gpiochip_add(&state->chip);
+ if (ret) {
+ dev_err(state->dev, "can't add gpio chip\n");
+ goto err_chip;
+ }
+
+ ret = gpiochip_add_pin_range(&state->chip, dev_name(dev), 0, 0, npins);
+ if (ret) {
+ dev_err(dev, "failed to add pin range\n");
+ goto err_range;
+ }
+
+ return 0;
+
+err_range:
+ gpiochip_remove(&state->chip);
+err_chip:
+ pinctrl_unregister(state->ctrl);
+ return ret;
+}
+
+static int pmic_mpp_remove(struct platform_device *pdev)
+{
+ struct pmic_mpp_state *state = platform_get_drvdata(pdev);
+
+ gpiochip_remove(&state->chip);
+ pinctrl_unregister(state->ctrl);
+ return 0;
+}
+
+static const struct of_device_id pmic_mpp_of_match[] = {
+ { .compatible = "qcom,pm8841-mpp" }, /* 4 MPP's */
+ { .compatible = "qcom,pm8941-mpp" }, /* 8 MPP's */
+ { .compatible = "qcom,pma8084-mpp" }, /* 8 MPP's */
+ { },
+};
+
+MODULE_DEVICE_TABLE(of, pmic_mpp_of_match);
+
+static struct platform_driver pmic_mpp_driver = {
+ .driver = {
+ .name = "qcom-spmi-mpp",
+ .of_match_table = pmic_mpp_of_match,
+ },
+ .probe = pmic_mpp_probe,
+ .remove = pmic_mpp_remove,
+};
+
+module_platform_driver(pmic_mpp_driver);
+
+MODULE_AUTHOR("Ivan T. Ivanov <iivanov@mm-sol.com>");
+MODULE_DESCRIPTION("Qualcomm SPMI PMIC MPP pin control driver");
+MODULE_ALIAS("platform:qcom-spmi-mpp");
+MODULE_LICENSE("GPL v2");
--
1.9.1
^ permalink raw reply related [flat|nested] 6+ messages in thread* Re: [PATCH v6 0/4] Qualcomm SPMI PMIC pin controller drivers
2014-10-22 9:58 [PATCH v6 0/4] Qualcomm SPMI PMIC pin controller drivers Ivan T. Ivanov
` (3 preceding siblings ...)
2014-10-22 9:58 ` [PATCH v6 4/4] pinctrl: Qualcomm SPMI PMIC MPP " Ivan T. Ivanov
@ 2014-10-28 16:29 ` Linus Walleij
4 siblings, 0 replies; 6+ messages in thread
From: Linus Walleij @ 2014-10-28 16:29 UTC (permalink / raw)
To: Ivan T. Ivanov
Cc: Rob Herring, Mark Rutland, Pawel Moll, Ian Campbell, Kumar Gala,
Grant Likely, Bjorn Andersson, Georgi Djakov, Andy Gross,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-arm-msm@vger.kernel.org
On Wed, Oct 22, 2014 at 11:58 AM, Ivan T. Ivanov <iivanov@mm-sol.com> wrote:
> Changes since v4:
>
> - Rebased on v3.18-rc1:
> pinmux_ops.enable is now pinmux_ops.set_mux
> gpiochip_remove() did not return a value.
> - Added Ack's from Bjorn
Thanks guys, I have applied the latest version of the v6 patch series,
including the v6-prim version of 3/4 that fixed the compile error...
Unless something radically bad happens it goes into v3.19.
Yours,
Linus Walleij
^ permalink raw reply [flat|nested] 6+ messages in thread