[PATCHv6 0/6] ARM: imx: Add Freescale LS1021A SoC and board support

[PATCHv6 0/6] ARM: imx: Add Freescale LS1021A SoC and board support

[Jingchang Lu]

This series contain the support for Freescale LS1021A CPU and LS1021A-QDS
and LS1021A-TWR board.

The LS1021A SoC combines two ARM Cortex-A7 cores that have been optimized
for high reliability and pack the highest level of integration available
for sub-3W embedded communications processors and with a comprehensive
enablement model focused on ease of programmability.

The LS1021A SoC shares IPs with i.MX family, Vybrid family and Freescale
PowerPC platform. 

For the detail information about LS1021A SoC, please refer to the RM doc.

---
changes in v6:
 add dts patch description.
 remove '-' from QDS and TWR board dts name for consistence with u-boot.

changes in v5:
 remove unideal dts nodes for later add.
 add X11 license to dts files.

changes in v4:
 add "syscon" compatible to scfg and dcfg dts node.
 remove mxc_restart in the platform machine desc.
 remove dma_zone_size defination.

changes in v3:
 rewrite scfg and dcfg binding doc description.
 remove sai related node leaving to the driver support.

changes in v2:
 remove unused nodes.
 wakeup the secondary core by IPI call to u-boot standby procedure. 
 add dt-bindings for LS1021A SoC and platform gerenal configuration nodes.

----------------------------------------------------------------
Jingchang Lu (6):
	ARM: dts: Add SoC level device tree support for LS1021A
	ARM: dts: Add initial LS1021A QDS board dts support
	ARM: dts: Add initial LS1021A TWR board dts support
	dt-bindings: arm: add Freescale LS1021A SoC device tree binding
	ARM: imx: Add initial support for Freescale LS1021A
	ARM: imx: Add Freescale LS1021A SMP support

 Documentation/devicetree/bindings/arm/fsl.txt |  38 +++++
 arch/arm/boot/dts/Makefile                    |   2 +
 arch/arm/boot/dts/ls1021a.dtsi                | 408 ++++++++++++++++++++++++++++++++++++++++++++++++++
 arch/arm/boot/dts/ls1021aqds.dts              | 240 +++++++++++++++++++++++++++++
 arch/arm/boot/dts/ls1021atwr.dts              | 127 ++++++++++++++++
 arch/arm/mach-imx/Kconfig                     |  14 ++
 arch/arm/mach-imx/Makefile                    |   4 +-
 arch/arm/mach-imx/common.h                    |   1 +
 arch/arm/mach-imx/mach-ls1021a.c              |  22 +++
 arch/arm/mach-imx/platsmp.c                   |  33 ++++
 10 files changed, 888 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/boot/dts/ls1021a.dtsi
 create mode 100644 arch/arm/boot/dts/ls1021aqds.dts
 create mode 100755 arch/arm/boot/dts/ls1021atwr.dts
 create mode 100644 arch/arm/mach-imx/mach-ls1021a.c

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCHv6 1/6] ARM: dts: Add SoC level device tree support for LS1021A

[Jingchang Lu]

From: Jingchang Lu <b35083-KZfg59tc24xl57MIdRCFDg@public.gmane.org>

This add Freescale QorIQ LS1021A SoC device tree support.
The QorIQ LS1021A processor incorporates dual ARM Cortex-A7 cores,
providing virtualization support, advanced security features and the
broadest array of high-speed interconnects and optimized peripheral
features.

The LS1021A SoC shares IPs with i.MX, Vybrid and PowerPC platform.

For the detail information about Freescale QorIQ LS1021A SoC,
please refer to the QorIQ LS1021A Reference Manual.

Signed-off-by: Nikhil Badola <nikhil.badola-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
Signed-off-by: Chenhui Zhao <chenhui.zhao-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
Signed-off-by: Suresh Gupta <suresh.gupta-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
Signed-off-by: Shaveta Leekha <shaveta-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
Signed-off-by: Ruchika Gupta <ruchika.gupta-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
Signed-off-by: Chao Fu <b44548-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
Signed-off-by: Tang Yuantian <Yuantian.Tang-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
Signed-off-by: Alison Wang <alison.wang-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
Signed-off-by: Jingchang Lu <jingchang.lu-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
---
 arch/arm/boot/dts/ls1021a.dtsi | 408 +++++++++++++++++++++++++++++++++++++++++
 1 file changed, 408 insertions(+)
 create mode 100644 arch/arm/boot/dts/ls1021a.dtsi

diff --git a/arch/arm/boot/dts/ls1021a.dtsi b/arch/arm/boot/dts/ls1021a.dtsi
new file mode 100644
index 0000000..657da14
--- /dev/null
+++ b/arch/arm/boot/dts/ls1021a.dtsi
@@ -0,0 +1,408 @@
+/*
+ * Copyright 2013-2014 Freescale Semiconductor, Inc.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of
+ *     the License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ *     You should have received a copy of the GNU General Public
+ *     License along with this file; if not, write to the Free
+ *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ *     MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "skeleton64.dtsi"
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	compatible = "fsl,ls1021a";
+	interrupt-parent = <&gic>;
+
+	aliases {
+		serial0 = &lpuart0;
+		serial1 = &lpuart1;
+		serial2 = &lpuart2;
+		serial3 = &lpuart3;
+		serial4 = &lpuart4;
+		serial5 = &lpuart5;
+		sysclk = &sysclk;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@f00 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <0xf00>;
+			clocks = <&cluster1_clk>;
+		};
+
+		cpu@f01 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <0xf01>;
+			clocks = <&cluster1_clk>;
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		device_type = "soc";
+		interrupt-parent = <&gic>;
+		ranges;
+
+		gic: interrupt-controller@1400000 {
+			compatible = "arm,cortex-a7-gic";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			reg = <0x0 0x1401000 0x0 0x1000>,
+			      <0x0 0x1402000 0x0 0x1000>,
+			      <0x0 0x1404000 0x0 0x2000>,
+			      <0x0 0x1406000 0x0 0x2000>;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>;
+
+		};
+
+		ifc: ifc@1530000 {
+			compatible = "fsl,ifc", "simple-bus";
+			reg = <0x0 0x1530000 0x0 0x10000>;
+			interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		dcfg: dcfg@1ee0000 {
+			compatible = "fsl,ls1021a-dcfg", "syscon";
+			reg = <0x0 0x1ee0000 0x0 0x10000>;
+			big-endian;
+		};
+
+		esdhc: esdhc@1560000 {
+			compatible = "fsl,esdhc";
+			reg = <0x0 0x1560000 0x0 0x10000>;
+			interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
+			clock-frequency = <0>;
+			voltage-ranges = <1800 1800 3300 3300>;
+			sdhci,auto-cmd12;
+			big-endian;
+			bus-width = <4>;
+			status = "disabled";
+		};
+
+		scfg: scfg@1570000 {
+			compatible = "fsl,ls1021a-scfg", "syscon";
+			reg = <0x0 0x1570000 0x0 0x10000>;
+		};
+
+		clockgen: clocking@1ee1000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x0 0x1ee1000 0x10000>;
+
+			sysclk: sysclk {
+				compatible = "fixed-clock";
+				#clock-cells = <0>;
+				clock-output-names = "sysclk";
+			};
+
+			cga_pll1: pll@800 {
+				compatible = "fsl,qoriq-core-pll-2.0";
+				#clock-cells = <1>;
+				reg = <0x800 0x10>;
+				clocks = <&sysclk>;
+				clock-output-names = "cga-pll1", "cga-pll1-div2",
+						     "cga-pll1-div4";
+			};
+
+			platform_clk: pll@c00 {
+				compatible = "fsl,qoriq-core-pll-2.0";
+				#clock-cells = <1>;
+				reg = <0xc00 0x10>;
+				clocks = <&sysclk>;
+				clock-output-names = "platform-clk", "platform-clk-div2";
+			};
+
+			cluster1_clk: clk0c0@0 {
+				compatible = "fsl,qoriq-core-mux-2.0";
+				#clock-cells = <0>;
+				reg = <0x0 0x10>;
+				clock-names = "pll1cga", "pll1cga-div2", "pll1cga-div4";
+				clocks = <&cga_pll1 0>, <&cga_pll1 1>, <&cga_pll1 2>;
+				clock-output-names = "cluster1-clk";
+			};
+		};
+
+		dspi0: dspi@2100000 {
+			compatible = "fsl,vf610-dspi";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0x2100000 0x0 0x10000>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "dspi";
+			clocks = <&platform_clk 1>;
+			spi-num-chipselects = <5>;
+			big-endian;
+			status = "disabled";
+		};
+
+		dspi1: dspi@2110000 {
+			compatible = "fsl,vf610-dspi";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0x2110000 0x0 0x10000>;
+			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "dspi";
+			clocks = <&platform_clk 1>;
+			spi-num-chipselects = <5>;
+			big-endian;
+			status = "disabled";
+		};
+
+		i2c0: i2c@2180000 {
+			compatible = "fsl,vf610-i2c";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0x2180000 0x0 0x10000>;
+			interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "i2c";
+			clocks = <&platform_clk 1>;
+			status = "disabled";
+		};
+
+		i2c1: i2c@2190000 {
+			compatible = "fsl,vf610-i2c";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0x2190000 0x0 0x10000>;
+			interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "i2c";
+			clocks = <&platform_clk 1>;
+			status = "disabled";
+		};
+
+		i2c2: i2c@21a0000 {
+			compatible = "fsl,vf610-i2c";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0x21a0000 0x0 0x10000>;
+			interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "i2c";
+			clocks = <&platform_clk 1>;
+			status = "disabled";
+		};
+
+		uart0: serial@21c0500 {
+			compatible = "fsl,16550-FIFO64", "ns16550a";
+			reg = <0x0 0x21c0500 0x0 0x100>;
+			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+			clock-frequency = <0>;
+			fifo-size = <15>;
+			status = "disabled";
+		};
+
+		uart1: serial@21c0600 {
+			compatible = "fsl,16550-FIFO64", "ns16550a";
+			reg = <0x0 0x21c0600 0x0 0x100>;
+			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+			clock-frequency = <0>;
+			fifo-size = <15>;
+			status = "disabled";
+		};
+
+		uart2: serial@21d0500 {
+			compatible = "fsl,16550-FIFO64", "ns16550a";
+			reg = <0x0 0x21d0500 0x0 0x100>;
+			interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+			clock-frequency = <0>;
+			fifo-size = <15>;
+			status = "disabled";
+		};
+
+		uart3: serial@21d0600 {
+			compatible = "fsl,16550-FIFO64", "ns16550a";
+			reg = <0x0 0x21d0600 0x0 0x100>;
+			interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+			clock-frequency = <0>;
+			fifo-size = <15>;
+			status = "disabled";
+		};
+
+		lpuart0: serial@2950000 {
+			compatible = "fsl,ls1021a-lpuart";
+			reg = <0x0 0x2950000 0x0 0x1000>;
+			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&sysclk>;
+			clock-names = "ipg";
+			status = "disabled";
+		};
+
+		lpuart1: serial@2960000 {
+			compatible = "fsl,ls1021a-lpuart";
+			reg = <0x0 0x2960000 0x0 0x1000>;
+			interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&platform_clk 1>;
+			clock-names = "ipg";
+			status = "disabled";
+		};
+
+		lpuart2: serial@2970000 {
+			compatible = "fsl,ls1021a-lpuart";
+			reg = <0x0 0x2970000 0x0 0x1000>;
+			interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&platform_clk 1>;
+			clock-names = "ipg";
+			status = "disabled";
+		};
+
+		lpuart3: serial@2980000 {
+			compatible = "fsl,ls1021a-lpuart";
+			reg = <0x0 0x2980000 0x0 0x1000>;
+			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&platform_clk 1>;
+			clock-names = "ipg";
+			status = "disabled";
+		};
+
+		lpuart4: serial@2990000 {
+			compatible = "fsl,ls1021a-lpuart";
+			reg = <0x0 0x2990000 0x0 0x1000>;
+			interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&platform_clk 1>;
+			clock-names = "ipg";
+			status = "disabled";
+		};
+
+		lpuart5: serial@29a0000 {
+			compatible = "fsl,ls1021a-lpuart";
+			reg = <0x0 0x29a0000 0x0 0x1000>;
+			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&platform_clk 1>;
+			clock-names = "ipg";
+			status = "disabled";
+		};
+
+		wdog0: watchdog@2ad0000 {
+			compatible = "fsl,imx21-wdt";
+			reg = <0x0 0x2ad0000 0x0 0x10000>;
+			interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&platform_clk 1>;
+			clock-names = "wdog-en";
+			big-endian;
+		};
+
+		sai1: sai@2b50000 {
+			compatible = "fsl,vf610-sai";
+			reg = <0x0 0x2b50000 0x0 0x10000>;
+			interrupts = <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&platform_clk 1>;
+			clock-names = "sai";
+			dma-names = "tx", "rx";
+			dmas = <&edma0 1 47>,
+			       <&edma0 1 46>;
+			big-endian;
+			status = "disabled";
+		};
+
+		sai2: sai@2b60000 {
+			compatible = "fsl,vf610-sai";
+			reg = <0x0 0x2b60000 0x0 0x10000>;
+			interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&platform_clk 1>;
+			clock-names = "sai";
+			dma-names = "tx", "rx";
+			dmas = <&edma0 1 45>,
+			       <&edma0 1 44>;
+			big-endian;
+			status = "disabled";
+		};
+
+		edma0: edma@2c00000 {
+			#dma-cells = <2>;
+			compatible = "fsl,vf610-edma";
+			reg = <0x0 0x2c00000 0x0 0x10000>,
+			      <0x0 0x2c10000 0x0 0x10000>,
+			      <0x0 0x2c20000 0x0 0x10000>;
+			interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "edma-tx", "edma-err";
+			dma-channels = <32>;
+			big-endian;
+			clock-names = "dmamux0", "dmamux1";
+			clocks = <&platform_clk 1>,
+				 <&platform_clk 1>;
+		};
+
+		mdio0: mdio@2d24000 {
+			compatible = "gianfar";
+			device_type = "mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0x2d24000 0x0 0x4000>;
+		};
+
+		usb@8600000 {
+			compatible = "fsl-usb2-dr-v2.5", "fsl-usb2-dr";
+			reg = <0x0 0x8600000 0x0 0x1000>;
+			interrupts = <GIC_SPI 171 IRQ_TYPE_LEVEL_HIGH>;
+			dr_mode = "host";
+			phy_type = "ulpi";
+		};
+
+		usb3@3100000 {
+			compatible = "snps,dwc3";
+			reg = <0x0 0x3100000 0x0 0x10000>;
+			interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
+			dr_mode = "host";
+		};
+	};
+};
-- 
1.8.0

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCHv6 2/6] ARM: dts: Add initial LS1021A QDS board dts support

[Jingchang Lu]

From: Jingchang Lu <b35083-KZfg59tc24xl57MIdRCFDg@public.gmane.org>

The LS1021A QorIQ development system (QDS) is a high-performance
computing evaluation, development and test platform supporting
the LS1021A processor. The LS1021A QDS is optimized to support
the high-bandwidth DDR3LP/DDR4 memory and a full complement of
high-speed SerDes ports.

For more detail information about the LS1021AQDS, please refer to
the QorIQ LS1021A Development System Reference Manual.

Signed-off-by: Alison Wang <alison.wang-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
Signed-off-by: Chao Fu <B44548-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
Signed-off-by: Jason Jin <Jason.Jin-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
Signed-off-by: Xiubo Li <Li.Xiubo-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
Signed-off-by: Jaiprakash Singh <b44839-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
Signed-off-by: Jingchang Lu <jingchang.lu-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
---
 arch/arm/boot/dts/Makefile       |   1 +
 arch/arm/boot/dts/ls1021aqds.dts | 240 +++++++++++++++++++++++++++++++++++++++
 2 files changed, 241 insertions(+)
 create mode 100644 arch/arm/boot/dts/ls1021aqds.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 4a75e29..d75527a 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -251,6 +251,7 @@ dtb-$(CONFIG_ARCH_MXC) += \
 	imx6q-tx6q-1110.dtb \
 	imx6sl-evk.dtb \
 	imx6sx-sdb.dtb \
+	ls1021aqds.dtb \
 	vf610-colibri-eval-v3.dtb \
 	vf610-cosmic.dtb \
 	vf610-twr.dtb
diff --git a/arch/arm/boot/dts/ls1021aqds.dts b/arch/arm/boot/dts/ls1021aqds.dts
new file mode 100644
index 0000000..9c5e16b
--- /dev/null
+++ b/arch/arm/boot/dts/ls1021aqds.dts
@@ -0,0 +1,240 @@
+/*
+ * Copyright 2013-2014 Freescale Semiconductor, Inc.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of
+ *     the License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ *     You should have received a copy of the GNU General Public
+ *     License along with this file; if not, write to the Free
+ *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ *     MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "ls1021a.dtsi"
+
+/ {
+	model = "LS1021A QDS Board";
+
+	aliases {
+		enet0_rgmii_phy = &rgmii_phy1;
+		enet1_rgmii_phy = &rgmii_phy2;
+		enet2_rgmii_phy = &rgmii_phy3;
+		enet0_sgmii_phy = &sgmii_phy1c;
+		enet1_sgmii_phy = &sgmii_phy1d;
+	};
+};
+
+&dspi0 {
+	bus-num = <0>;
+	status = "okay";
+
+	dspiflash: at45db021d@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "atmel,at45db021d", "atmel,at45", "atmel,dataflash";
+		spi-max-frequency = <16000000>;
+		spi-cpol;
+		spi-cpha;
+		reg = <0>;
+	};
+};
+
+&i2c0 {
+	status = "okay";
+
+	pca9547: mux@77 {
+		reg = <0x77>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0>;
+
+			ds3232: rtc@68 {
+				compatible = "dallas,ds3232";
+				reg = <0x68>;
+				interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
+			};
+		};
+
+		i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x2>;
+
+			ina220@40 {
+				compatible = "ti,ina220";
+				reg = <0x40>;
+				shunt-resistor = <1000>;
+			};
+
+			ina220@41 {
+				compatible = "ti,ina220";
+				reg = <0x41>;
+				shunt-resistor = <1000>;
+			};
+		};
+
+		i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x3>;
+
+			eeprom@56 {
+				compatible = "atmel,24c512";
+				reg = <0x56>;
+			};
+
+			eeprom@57 {
+				compatible = "atmel,24c512";
+				reg = <0x57>;
+			};
+
+			adt7461a@4c {
+				compatible = "adi,adt7461a";
+				reg = <0x4c>;
+			};
+		};
+	};
+};
+
+&ifc {
+	#address-cells = <2>;
+	#size-cells = <1>;
+	/* NOR, NAND Flashes and FPGA on board */
+	ranges = <0x0 0x0 0x0 0x60000000 0x08000000
+		  0x2 0x0 0x0 0x7e800000 0x00010000
+		  0x3 0x0 0x0 0x7fb00000 0x00000100>;
+	status = "okay";
+
+	nor@0,0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "cfi-flash";
+		reg = <0x0 0x0 0x8000000>;
+		bank-width = <2>;
+		device-width = <1>;
+	};
+
+	fpga: board-control@3,0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "simple-bus";
+		reg = <0x3 0x0 0x0000100>;
+		bank-width = <1>;
+		device-width = <1>;
+		ranges = <0 3 0 0x100>;
+
+		mdio-mux-emi1 {
+			compatible = "mdio-mux-mmioreg";
+			mdio-parent-bus = <&mdio0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x54 1>; /* BRDCFG4 */
+			mux-mask = <0xe0>; /* EMI1[2:0] */
+
+			/* Onboard PHYs */
+			ls1021amdio0: mdio@0 {
+				reg = <0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				rgmii_phy1: ethernet-phy@1 {
+					reg = <0x1>;
+				};
+			};
+
+			ls1021amdio1: mdio@20 {
+				reg = <0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				rgmii_phy2: ethernet-phy@2 {
+					reg = <0x2>;
+				};
+			};
+
+			ls1021amdio2: mdio@40 {
+				reg = <0x40>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				rgmii_phy3: ethernet-phy@3 {
+					reg = <0x3>;
+				};
+			};
+
+			ls1021amdio3: mdio@60 {
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				sgmii_phy1c: ethernet-phy@1c {
+					reg = <0x1c>;
+				};
+			};
+
+			ls1021amdio4: mdio@80 {
+				reg = <0x80>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				sgmii_phy1d: ethernet-phy@1d {
+					reg = <0x1d>;
+				};
+			};
+		};
+	};
+};
+
+&lpuart0 {
+	status = "okay";
+};
+
+&mdio0 {
+	tbi0: tbi-phy@8 {
+		reg = <0x8>;
+		device_type = "tbi-phy";
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
-- 
1.8.0

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCHv6 3/6] ARM: dts: Add initial LS1021A TWR board dts support

[Jingchang Lu]

The LS1021A TWR is a low cost, high-performance evaluation,
development and test platform supporting the LS1021A processor.
It is optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.

For more detail information about the LS1021A TWR board, please
refer to LS1021A QorIQ Tower System Reference Manual.

Signed-off-by: Chao Fu <B44548-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
Signed-off-by: Jingchang Lu <jingchang.lu-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
---
 arch/arm/boot/dts/Makefile       |   1 +
 arch/arm/boot/dts/ls1021atwr.dts | 127 +++++++++++++++++++++++++++++++++++++++
 2 files changed, 128 insertions(+)
 create mode 100755 arch/arm/boot/dts/ls1021atwr.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index d75527a..9ce43aa 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -252,6 +252,7 @@ dtb-$(CONFIG_ARCH_MXC) += \
 	imx6sl-evk.dtb \
 	imx6sx-sdb.dtb \
 	ls1021aqds.dtb \
+	ls1021atwr.dtb \
 	vf610-colibri-eval-v3.dtb \
 	vf610-cosmic.dtb \
 	vf610-twr.dtb
diff --git a/arch/arm/boot/dts/ls1021atwr.dts b/arch/arm/boot/dts/ls1021atwr.dts
new file mode 100755
index 0000000..a2c591e
--- /dev/null
+++ b/arch/arm/boot/dts/ls1021atwr.dts
@@ -0,0 +1,127 @@
+/*
+ * Copyright 2013-2014 Freescale Semiconductor, Inc.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of
+ *     the License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ *     You should have received a copy of the GNU General Public
+ *     License along with this file; if not, write to the Free
+ *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ *     MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "ls1021a.dtsi"
+
+/ {
+	model = "LS1021A TWR Board";
+
+	aliases {
+		enet2_rgmii_phy = &rgmii_phy1;
+		enet0_sgmii_phy = &sgmii_phy2;
+		enet1_sgmii_phy = &sgmii_phy0;
+	};
+};
+
+&dspi1 {
+	bus-num = <0>;
+	status = "okay";
+
+	dspiflash: s25fl064k@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "spansion,s25fl064k";
+		spi-max-frequency = <16000000>;
+		spi-cpol;
+		spi-cpha;
+		reg = <0>;
+	};
+};
+
+&i2c0 {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&ifc {
+	#address-cells = <2>;
+	#size-cells = <1>;
+	/* NOR Flash on board */
+	ranges = <0x0 0x0 0x0 0x60000000 0x08000000>;
+	status = "okay";
+
+	nor@0,0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "cfi-flash";
+		reg = <0x0 0x0 0x8000000>;
+		bank-width = <2>;
+		device-width = <1>;
+	};
+};
+
+&lpuart0 {
+	status = "okay";
+};
+
+&mdio0 {
+	sgmii_phy0: ethernet-phy@0 {
+		reg = <0x0>;
+	};
+	rgmii_phy1: ethernet-phy@1 {
+		reg = <0x1>;
+	};
+	sgmii_phy2: ethernet-phy@2 {
+		reg = <0x2>;
+	};
+	tbi1: tbi-phy@1f {
+		reg = <0x1f>;
+		device_type = "tbi-phy";
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
-- 
1.8.0

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCHv5 RESEND 4/6] dt-bindings: arm: add Freescale LS1021A SoC device tree binding

[Jingchang Lu]

Signed-off-by: Jingchang Lu <jingchang.lu-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
---
 Documentation/devicetree/bindings/arm/fsl.txt | 38 +++++++++++++++++++++++++++
 1 file changed, 38 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/fsl.txt b/Documentation/devicetree/bindings/arm/fsl.txt
index e935d7d..4e8b7df 100644
--- a/Documentation/devicetree/bindings/arm/fsl.txt
+++ b/Documentation/devicetree/bindings/arm/fsl.txt
@@ -74,3 +74,41 @@ Required root node properties:
 i.MX6q generic board
 Required root node properties:
     - compatible = "fsl,imx6q";
+
+
+Freescale LS1021A Platform Device Tree Bindings
+------------------------------------------------
+
+Required root node compatible properties:
+  - compatible = "fsl,ls1021a";
+
+Freescale LS1021A SoC-specific Device Tree Bindings
+-------------------------------------------
+
+Freescale SCFG
+  SCFG is the supplemental configuration unit, that provides SoC specific
+configuration and status registers for the chip. Such as getting PEX port
+status.
+  Required properties:
+  - compatible: should be "fsl,ls1021a-scfg"
+  - reg: should contain base address and length of SCFG memory-mapped registers
+
+Example:
+	scfg: scfg@1570000 {
+		compatible = "fsl,ls1021a-scfg";
+		reg = <0x0 0x1570000 0x0 0x10000>;
+	};
+
+Freescale DCFG
+  DCFG is the device configuration unit, that provides general purpose
+configuration and status for the device. Such as setting the secondary
+core start address and release the secondary core from holdoff and startup.
+  Required properties:
+  - compatible: should be "fsl,ls1021a-dcfg"
+  - reg : should contain base address and length of DCFG memory-mapped registers
+
+Example:
+	dcfg: dcfg@1ee0000 {
+		compatible = "fsl,ls1021a-dcfg";
+		reg = <0x0 0x1ee0000 0x0 0x10000>;
+	};
-- 
1.8.0

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCHv5 RESEND 5/6] ARM: imx: Add initial support for Freescale LS1021A

[Jingchang Lu]

From: Jingchang Lu <b35083-KZfg59tc24xl57MIdRCFDg@public.gmane.org>

The LS1021A SoC is a dual-core Cortex-A7 based processor,
this adds the initial support for it.

Signed-off-by: Jingchang Lu <b35083-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
---
 arch/arm/mach-imx/Kconfig        | 14 ++++++++++++++
 arch/arm/mach-imx/Makefile       |  2 ++
 arch/arm/mach-imx/mach-ls1021a.c | 21 +++++++++++++++++++++
 3 files changed, 37 insertions(+)
 create mode 100644 arch/arm/mach-imx/mach-ls1021a.c

diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig
index 11b2957..49a0096 100644
--- a/arch/arm/mach-imx/Kconfig
+++ b/arch/arm/mach-imx/Kconfig
@@ -639,6 +639,20 @@ config SOC_VF610
 	help
 	  This enable support for Freescale Vybrid VF610 processor.
 
+config FSL_SOC
+	bool
+
+config SOC_LS1021A
+	bool "Freescale LS1021A support"
+	select ARM_GIC
+	select HAVE_ARM_ARCH_TIMER
+	select FSL_SOC
+	select PCI_DOMAINS if PCI
+	select ZONE_DMA if ARM_LPAE
+
+	help
+	  This enable support for Freescale LS1021A processor.
+
 endif
 
 source "arch/arm/mach-imx/devices/Kconfig"
diff --git a/arch/arm/mach-imx/Makefile b/arch/arm/mach-imx/Makefile
index 6e4fcd8..ce137bc 100644
--- a/arch/arm/mach-imx/Makefile
+++ b/arch/arm/mach-imx/Makefile
@@ -110,4 +110,6 @@ obj-$(CONFIG_SOC_IMX53) += mach-imx53.o
 
 obj-$(CONFIG_SOC_VF610) += clk-vf610.o mach-vf610.o
 
+obj-$(CONFIG_SOC_LS1021A) += mach-ls1021a.o
+
 obj-y += devices/
diff --git a/arch/arm/mach-imx/mach-ls1021a.c b/arch/arm/mach-imx/mach-ls1021a.c
new file mode 100644
index 0000000..9d2034b
--- /dev/null
+++ b/arch/arm/mach-imx/mach-ls1021a.c
@@ -0,0 +1,21 @@
+/*
+ * Copyright 2013-2014 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <asm/mach/arch.h>
+
+#include "common.h"
+
+static const char * const ls1021a_dt_compat[] __initconst = {
+	"fsl,ls1021a",
+	NULL,
+};
+
+DT_MACHINE_START(LS1021A, "Freescale LS1021A")
+	.dt_compat	= ls1021a_dt_compat,
+MACHINE_END
-- 
1.8.0

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCHv6 6/6] ARM: imx: Add Freescale LS1021A SMP support

[Jingchang Lu]

From: Jingchang Lu <b35083-KZfg59tc24xl57MIdRCFDg@public.gmane.org>

Freescale LS1021A SoCs deploy two cortex-A7 processors,
this adds bring-up support for the secondary core.

Signed-off-by: Jingchang Lu <b35083-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
---
 arch/arm/mach-imx/Makefile       |  2 +-
 arch/arm/mach-imx/common.h       |  1 +
 arch/arm/mach-imx/mach-ls1021a.c |  1 +
 arch/arm/mach-imx/platsmp.c      | 33 +++++++++++++++++++++++++++++++++
 4 files changed, 36 insertions(+), 1 deletion(-)

diff --git a/arch/arm/mach-imx/Makefile b/arch/arm/mach-imx/Makefile
index ce137bc..38d75e2 100644
--- a/arch/arm/mach-imx/Makefile
+++ b/arch/arm/mach-imx/Makefile
@@ -89,7 +89,7 @@ obj-$(CONFIG_HAVE_IMX_ANATOP) += anatop.o
 obj-$(CONFIG_HAVE_IMX_GPC) += gpc.o
 obj-$(CONFIG_HAVE_IMX_MMDC) += mmdc.o
 obj-$(CONFIG_HAVE_IMX_SRC) += src.o
-ifdef CONFIG_SOC_IMX6
+ifneq ($(CONFIG_SOC_IMX6)$(CONFIG_SOC_LS1021A),)
 AFLAGS_headsmp.o :=-Wa,-march=armv7-a
 obj-$(CONFIG_SMP) += headsmp.o platsmp.o
 obj-$(CONFIG_HOTPLUG_CPU) += hotplug.o
diff --git a/arch/arm/mach-imx/common.h b/arch/arm/mach-imx/common.h
index 1dabf43..c473ca5 100644
--- a/arch/arm/mach-imx/common.h
+++ b/arch/arm/mach-imx/common.h
@@ -157,5 +157,6 @@ static inline void imx_init_l2cache(void) {}
 #endif
 
 extern struct smp_operations imx_smp_ops;
+extern struct smp_operations ls1021a_smp_ops;
 
 #endif
diff --git a/arch/arm/mach-imx/mach-ls1021a.c b/arch/arm/mach-imx/mach-ls1021a.c
index 9d2034b..b89c858 100644
--- a/arch/arm/mach-imx/mach-ls1021a.c
+++ b/arch/arm/mach-imx/mach-ls1021a.c
@@ -17,5 +17,6 @@ static const char * const ls1021a_dt_compat[] __initconst = {
 };
 
 DT_MACHINE_START(LS1021A, "Freescale LS1021A")
+	.smp		= smp_ops(ls1021a_smp_ops),
 	.dt_compat	= ls1021a_dt_compat,
 MACHINE_END
diff --git a/arch/arm/mach-imx/platsmp.c b/arch/arm/mach-imx/platsmp.c
index 771bd25..7f27001 100644
--- a/arch/arm/mach-imx/platsmp.c
+++ b/arch/arm/mach-imx/platsmp.c
@@ -11,7 +11,10 @@
  */
 
 #include <linux/init.h>
+#include <linux/of_address.h>
+#include <linux/of.h>
 #include <linux/smp.h>
+
 #include <asm/cacheflush.h>
 #include <asm/page.h>
 #include <asm/smp_scu.h>
@@ -94,3 +97,33 @@ struct smp_operations  imx_smp_ops __initdata = {
 	.cpu_kill		= imx_cpu_kill,
 #endif
 };
+
+#define DCFG_CCSR_SCRATCHRW1	0x200
+
+static int ls1021a_boot_secondary(unsigned int cpu, struct task_struct *idle)
+{
+	arch_send_wakeup_ipi_mask(cpumask_of(cpu));
+
+	return 0;
+}
+
+static void __init ls1021a_smp_prepare_cpus(unsigned int max_cpus)
+{
+	struct device_node *np;
+	void __iomem *dcfg_base;
+	unsigned long paddr;
+
+	np = of_find_compatible_node(NULL, NULL, "fsl,ls1021a-dcfg");
+	dcfg_base = of_iomap(np, 0);
+	BUG_ON(!dcfg_base);
+
+	paddr = virt_to_phys(secondary_startup);
+	writel_relaxed(cpu_to_be32(paddr), dcfg_base + DCFG_CCSR_SCRATCHRW1);
+
+	iounmap(dcfg_base);
+}
+
+struct smp_operations  ls1021a_smp_ops __initdata = {
+	.smp_prepare_cpus	= ls1021a_smp_prepare_cpus,
+	.smp_boot_secondary	= ls1021a_boot_secondary,
+};
-- 
1.8.0

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCHv6 0/6] ARM: imx: Add Freescale LS1021A SoC and board support

[Shawn Guo]

On Fri, Oct 24, 2014 at 06:08:41PM +0800, Jingchang Lu wrote:
> This series contain the support for Freescale LS1021A CPU and LS1021A-QDS
> and LS1021A-TWR board.
> 
> The LS1021A SoC combines two ARM Cortex-A7 cores that have been optimized
> for high reliability and pack the highest level of integration available
> for sub-3W embedded communications processors and with a comprehensive
> enablement model focused on ease of programmability.
> 
> The LS1021A SoC shares IPs with i.MX family, Vybrid family and Freescale
> PowerPC platform. 
> 
> For the detail information about LS1021A SoC, please refer to the RM doc.
> 
> ---
> changes in v6:
>  add dts patch description.
>  remove '-' from QDS and TWR board dts name for consistence with u-boot.

I'm not sure it's a good idea.  The most idiomatic DTS naming schema is
just <socname>-<boardname>.dts.

Shawn
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCHv6 0/6] ARM: imx: Add Freescale LS1021A SoC and board support

[Jingchang Lu]

________________________________________
From: Shawn Guo <shawn.guo-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
Sent: Sunday, October 26, 2014 8:23 AM
To: Lu Jingchang-B35083
Cc: arnd-r2nGTMty4D4@public.gmane.org; mark.rutland-5wv7dgnIgG8@public.gmane.org; linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org; devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Subject: Re: [PATCHv6 0/6] ARM: imx: Add Freescale LS1021A SoC and board support

On Fri, Oct 24, 2014 at 06:08:41PM +0800, Jingchang Lu wrote:
>> This series contain the support for Freescale LS1021A CPU and LS1021A-QDS
>> and LS1021A-TWR board.
>>
>> The LS1021A SoC combines two ARM Cortex-A7 cores that have been optimized
>> for high reliability and pack the highest level of integration available
> >for sub-3W embedded communications processors and with a comprehensive
>> enablement model focused on ease of programmability.
>>
>> The LS1021A SoC shares IPs with i.MX family, Vybrid family and Freescale
>> PowerPC platform.
>>
>> For the detail information about LS1021A SoC, please refer to the RM doc.
>>
>> ---
>> changes in v6:
>>  add dts patch description.
>>  remove '-' from QDS and TWR board dts name for consistence with u-boot.

>I'm not sure it's a good idea.  The most idiomatic DTS naming schema is
just <socname>-<boardname>.dts.
Many our PowerPC platforms doesn't have '-' between SoCs and board names. This becomes a project requirement when integrating in our SDK release, and I have renamed these board names internally, so I also rename them on upstream for consistence. Thanks.

Best Regards,
Jingchang

>Shawn
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCHv6 0/6] ARM: imx: Add Freescale LS1021A SoC and board support

[Stefan Agner]

Am 2014-10-26 15:57, schrieb Jingchang Lu:
<snip>
>>> ---
>>> changes in v6:
>>>  add dts patch description.
>>>  remove '-' from QDS and TWR board dts name for consistence with u-boot.
> 
>>I'm not sure it's a good idea.  The most idiomatic DTS naming schema is
> just <socname>-<boardname>.dts.
> Many our PowerPC platforms doesn't have '-' between SoCs and board
> names. This becomes a project requirement when integrating in our SDK
> release, and I have renamed these board names internally, so I also
> rename them on upstream for consistence. Thanks.

Especially since this SoC has a letter in the end, its quite hard to
tell what is the SoC name and what is the board name. Hence I vote for
the hyphen too.

--
Stefan

> 
> Best Regards,
> Jingchang
> 
>>Shawn
> 
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html