From: Jingchang Lu <jingchang.lu-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
To: shawn.guo-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org
Cc: arnd-r2nGTMty4D4@public.gmane.org,
mark.rutland-5wv7dgnIgG8@public.gmane.org,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org,
devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
Jingchang Lu
<jingchang.lu-KZfg59tc24xl57MIdRCFDg@public.gmane.org>,
Chao Fu <B44548-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
Subject: [PATCHv7 3/6] ARM: dts: Add initial LS1021A TWR board dts support
Date: Fri, 31 Oct 2014 17:01:10 +0800 [thread overview]
Message-ID: <1414746073-12394-4-git-send-email-jingchang.lu@freescale.com> (raw)
In-Reply-To: <1414746073-12394-1-git-send-email-jingchang.lu-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
The LS1021A TWR is a low cost, high-performance evaluation,
development and test platform supporting the LS1021A processor.
It is optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.
For more detail information about the LS1021A TWR board, please
refer to LS1021A QorIQ Tower System Reference Manual.
Signed-off-by: Chao Fu <B44548-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
Signed-off-by: Jingchang Lu <jingchang.lu-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/ls1021a-twr.dts | 127 ++++++++++++++++++++++++++++++++++++++
2 files changed, 128 insertions(+)
create mode 100644 arch/arm/boot/dts/ls1021a-twr.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 515ce04..cdb561c 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -252,6 +252,7 @@ dtb-$(CONFIG_ARCH_MXC) += \
imx6sl-evk.dtb \
imx6sx-sdb.dtb \
ls1021a-qds.dtb \
+ ls1021a-twr.dtb \
vf610-colibri-eval-v3.dtb \
vf610-cosmic.dtb \
vf610-twr.dtb
diff --git a/arch/arm/boot/dts/ls1021a-twr.dts b/arch/arm/boot/dts/ls1021a-twr.dts
new file mode 100644
index 0000000..a2c591e
--- /dev/null
+++ b/arch/arm/boot/dts/ls1021a-twr.dts
@@ -0,0 +1,127 @@
+/*
+ * Copyright 2013-2014 Freescale Semiconductor, Inc.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "ls1021a.dtsi"
+
+/ {
+ model = "LS1021A TWR Board";
+
+ aliases {
+ enet2_rgmii_phy = &rgmii_phy1;
+ enet0_sgmii_phy = &sgmii_phy2;
+ enet1_sgmii_phy = &sgmii_phy0;
+ };
+};
+
+&dspi1 {
+ bus-num = <0>;
+ status = "okay";
+
+ dspiflash: s25fl064k@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spansion,s25fl064k";
+ spi-max-frequency = <16000000>;
+ spi-cpol;
+ spi-cpha;
+ reg = <0>;
+ };
+};
+
+&i2c0 {
+ status = "okay";
+};
+
+&i2c1 {
+ status = "okay";
+};
+
+&ifc {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ /* NOR Flash on board */
+ ranges = <0x0 0x0 0x0 0x60000000 0x08000000>;
+ status = "okay";
+
+ nor@0,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "cfi-flash";
+ reg = <0x0 0x0 0x8000000>;
+ bank-width = <2>;
+ device-width = <1>;
+ };
+};
+
+&lpuart0 {
+ status = "okay";
+};
+
+&mdio0 {
+ sgmii_phy0: ethernet-phy@0 {
+ reg = <0x0>;
+ };
+ rgmii_phy1: ethernet-phy@1 {
+ reg = <0x1>;
+ };
+ sgmii_phy2: ethernet-phy@2 {
+ reg = <0x2>;
+ };
+ tbi1: tbi-phy@1f {
+ reg = <0x1f>;
+ device_type = "tbi-phy";
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
--
1.8.0
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
next prev parent reply other threads:[~2014-10-31 9:01 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-10-31 9:01 [PATCHv7 0/6] ARM: imx: Add Freescale LS1021A SoC and board support Jingchang Lu
[not found] ` <1414746073-12394-1-git-send-email-jingchang.lu-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
2014-10-31 9:01 ` [RESENDv6 1/6] ARM: dts: Add SoC level device tree support for LS1021A Jingchang Lu
2014-10-31 9:01 ` [PATCHv7 2/6] ARM: dts: Add initial LS1021A QDS board dts support Jingchang Lu
2014-10-31 9:01 ` Jingchang Lu [this message]
2014-10-31 9:01 ` [RESENDv5 4/6] dt-bindings: arm: add Freescale LS1021A SoC device tree binding Jingchang Lu
2014-10-31 9:01 ` [RESENDv5 5/6] ARM: imx: Add initial support for Freescale LS1021A Jingchang Lu
[not found] ` <1414746073-12394-6-git-send-email-jingchang.lu-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
2014-11-11 16:03 ` [PATCH] ARM: imx: temporarily remove CONFIG_SOC_FSL from LS1021A Arnd Bergmann
2014-11-12 10:42 ` Shawn Guo
2014-11-12 11:04 ` Arnd Bergmann
2014-11-14 9:31 ` Jingchang Lu
[not found] ` <7b9de442bdd34acbb4398efe92a64a4f-CEkquS/Gb818MjqJKlOTwZwN6zqB+hSMnBOFsp37pqbUKgpGm//BTAC/G2K4zDHf@public.gmane.org>
2014-11-14 10:56 ` Arnd Bergmann
2014-10-31 9:01 ` [RESENDv6 6/6] ARM: imx: Add Freescale LS1021A SMP support Jingchang Lu
2014-11-04 5:28 ` [PATCHv7 0/6] ARM: imx: Add Freescale LS1021A SoC and board support Shawn Guo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1414746073-12394-4-git-send-email-jingchang.lu@freescale.com \
--to=jingchang.lu-kzfg59tc24xl57midrcfdg@public.gmane.org \
--cc=B44548-KZfg59tc24xl57MIdRCFDg@public.gmane.org \
--cc=arnd-r2nGTMty4D4@public.gmane.org \
--cc=devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org \
--cc=mark.rutland-5wv7dgnIgG8@public.gmane.org \
--cc=shawn.guo-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).