From mboxrd@z Thu Jan 1 00:00:00 1970 From: Roger Quadros Subject: [PATCH 4/5] ARM: dts: dra72-evm: Add extcon nodes for USB Date: Mon, 19 Jan 2015 19:52:21 +0200 Message-ID: <1421689942-10201-5-git-send-email-rogerq@ti.com> References: <1421689942-10201-1-git-send-email-rogerq@ti.com> Mime-Version: 1.0 Content-Type: text/plain Return-path: In-Reply-To: <1421689942-10201-1-git-send-email-rogerq@ti.com> Sender: linux-kernel-owner@vger.kernel.org To: balbi@ti.com, tony@atomide.com, myungjoo.ham@samsung.com, cw00.choi@samsung.com Cc: george.cherian@ti.com, nsekhar@ti.com, devicetree@vger.kernel.org, linux-usb@vger.kernel.org, linux-omap@vger.kernel.org, linux-kernel@vger.kernel.org, Roger Quadros List-Id: devicetree@vger.kernel.org On this EVM, the USB cable state has to be determined via the ID pin tied to a GPIO line. We use the gpio-usb-extcon driver to read the ID pin and the extcon framework to forward the USB cable state information to the USB driver so the controller can be configured in the right mode (host/peripheral). Gets USB peripheral mode to work on this EVM. Signed-off-by: Roger Quadros --- arch/arm/boot/dts/dra72-evm.dts | 31 +++++++++++++++++++++++++++++++ 1 file changed, 31 insertions(+) diff --git a/arch/arm/boot/dts/dra72-evm.dts b/arch/arm/boot/dts/dra72-evm.dts index 89085d0..d93a98f 100644 --- a/arch/arm/boot/dts/dra72-evm.dts +++ b/arch/arm/boot/dts/dra72-evm.dts @@ -8,6 +8,7 @@ /dts-v1/; #include "dra72x.dtsi" +#include / { model = "TI DRA722"; @@ -24,6 +25,16 @@ regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; }; + + extcon_usb1: extcon_usb1 { + compatible = "linux,extcon-usb"; + id-gpio = <&pcf_gpio_21 1 GPIO_ACTIVE_HIGH>; + }; + + extcon_usb2: extcon_usb2 { + compatible = "linux,extcon-usb"; + id-gpio = <&pcf_gpio_21 2 GPIO_ACTIVE_HIGH>; + }; }; &dra7_pmx_core { @@ -243,6 +254,18 @@ ti,palmas-long-press-seconds = <6>; }; }; + + pcf_gpio_21: gpio@21 { + compatible = "ti,pcf8575"; + reg = <0x21>; + lines-initial-states = <0x1408>; + gpio-controller; + #gpio-cells = <2>; + interrupt-parent = <&gpio6>; + interrupts = <11 IRQ_TYPE_EDGE_FALLING>; + interrupt-controller; + #interrupt-cells = <2>; + }; }; &uart1 { @@ -345,6 +368,14 @@ phy-supply = <&ldo4_reg>; }; +&omap_dwc3_1 { + extcon = <&extcon_usb1>; +}; + +&omap_dwc3_2 { + extcon = <&extcon_usb2>; +}; + &usb1 { dr_mode = "peripheral"; pinctrl-names = "default"; -- 2.1.0