* [PATCH 1/5] ARM: dts: zynq: Split out common Parallella bits
[not found] ` <1423702513-4032-1-git-send-email-afaerber-l3A5Bk7waGM@public.gmane.org>
@ 2015-02-12 0:55 ` Andreas Färber
0 siblings, 0 replies; 6+ messages in thread
From: Andreas Färber @ 2015-02-12 0:55 UTC (permalink / raw)
To: Michal Simek
Cc: Olof Johansson, Sören Brinkmann,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
Andreas Olofsson, Ola Jeppsson, Matteo Vit, Sean Rickerd,
Andreas Färber, Rob Herring, Pawel Moll, Mark Rutland,
Ian Campbell, Kumar Gala, Russell King,
open list:OPEN FIRMWARE AND..., open list
This prepares for the USB-less Microserver edition as well as
headless vs. HDMI bitstreams.
Cc: Ola Jeppsson <ola-hhg9azYwhpdWk0Htik3J/w@public.gmane.org>
Signed-off-by: Andreas Färber <afaerber-l3A5Bk7waGM@public.gmane.org>
---
arch/arm/boot/dts/zynq-parallella.dts | 80 +---------------------
.../{zynq-parallella.dts => zynq-parallella1.dtsi} | 3 +-
2 files changed, 3 insertions(+), 80 deletions(-)
copy arch/arm/boot/dts/{zynq-parallella.dts => zynq-parallella1.dtsi} (97%)
diff --git a/arch/arm/boot/dts/zynq-parallella.dts b/arch/arm/boot/dts/zynq-parallella.dts
index 0ebd2107022b..99ee6551ae8d 100644
--- a/arch/arm/boot/dts/zynq-parallella.dts
+++ b/arch/arm/boot/dts/zynq-parallella.dts
@@ -1,11 +1,6 @@
/*
* Copyright (c) 2014 SUSE LINUX Products GmbH
- *
- * Derived from zynq-zed.dts:
- *
- * Copyright (C) 2011 Xilinx
- * Copyright (C) 2012 National Instruments Corp.
- * Copyright (C) 2013 Xilinx
+ * Copyright (c) 2015 SUSE Linux GmbH
*
* This software is licensed under the terms of the GNU General Public
* License version 2, as published by the Free Software Foundation, and
@@ -17,79 +12,8 @@
* GNU General Public License for more details.
*/
/dts-v1/;
-/include/ "zynq-7000.dtsi"
+#include "zynq-parallella1.dtsi"
/ {
model = "Adapteva Parallella Board";
- compatible = "adapteva,parallella", "xlnx,zynq-7000";
-
- aliases {
- ethernet0 = &gem0;
- serial0 = &uart1;
- };
-
- memory {
- device_type = "memory";
- reg = <0x0 0x40000000>;
- };
-
- chosen {
- bootargs = "console=ttyPS0,115200 earlyprintk root=/dev/mmcblk0p2 rootfstype=ext4 rw rootwait";
- linux,stdout-path = "/amba/serial@e0001000";
- };
-};
-
-&clkc {
- fclk-enable = <0xf>;
- ps-clk-frequency = <33333333>;
-};
-
-&gem0 {
- status = "okay";
- phy-mode = "rgmii-id";
- phy-handle = <ðernet_phy>;
-
- ethernet_phy: ethernet-phy@0 {
- /* Marvell 88E1318 */
- compatible = "ethernet-phy-id0141.0e90",
- "ethernet-phy-ieee802.3-c22";
- reg = <0>;
- marvell,reg-init = <0x3 0x10 0xff00 0x1e>,
- <0x3 0x11 0xfff0 0xa>;
- };
-};
-
-&i2c0 {
- status = "okay";
-
- isl9305: isl9305@68 {
- compatible = "isil,isl9305";
- reg = <0x68>;
-
- regulators {
- dcd1 {
- regulator-name = "VDD_DSP";
- regulator-always-on;
- };
- dcd2 {
- regulator-name = "1P35V";
- regulator-always-on;
- };
- ldo1 {
- regulator-name = "VDD_ADJ";
- };
- ldo2 {
- regulator-name = "VDD_GPIO";
- regulator-always-on;
- };
- };
- };
-};
-
-&sdhci1 {
- status = "okay";
-};
-
-&uart1 {
- status = "okay";
};
diff --git a/arch/arm/boot/dts/zynq-parallella.dts b/arch/arm/boot/dts/zynq-parallella1.dtsi
similarity index 97%
copy from arch/arm/boot/dts/zynq-parallella.dts
copy to arch/arm/boot/dts/zynq-parallella1.dtsi
index 0ebd2107022b..7c1206f928bc 100644
--- a/arch/arm/boot/dts/zynq-parallella.dts
+++ b/arch/arm/boot/dts/zynq-parallella1.dtsi
@@ -1,5 +1,6 @@
/*
* Copyright (c) 2014 SUSE LINUX Products GmbH
+ * Copyright (c) 2015 SUSE Linux GmbH
*
* Derived from zynq-zed.dts:
*
@@ -16,11 +17,9 @@
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
-/dts-v1/;
/include/ "zynq-7000.dtsi"
/ {
- model = "Adapteva Parallella Board";
compatible = "adapteva,parallella", "xlnx,zynq-7000";
aliases {
--
2.2.2
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH 2/5] ARM: dts: zynq: Add pinctrl to Parallella
[not found] <1423702513-4032-1-git-send-email-afaerber@suse.de>
[not found] ` <1423702513-4032-1-git-send-email-afaerber-l3A5Bk7waGM@public.gmane.org>
@ 2015-02-12 0:55 ` Andreas Färber
2015-02-12 0:55 ` [PATCH 3/5] ARM: dts: zynq: Add LED for Parallella Andreas Färber
` (2 subsequent siblings)
4 siblings, 0 replies; 6+ messages in thread
From: Andreas Färber @ 2015-02-12 0:55 UTC (permalink / raw)
To: Michal Simek
Cc: Olof Johansson, Sören Brinkmann, linux-arm-kernel,
Andreas Olofsson, Ola Jeppsson, Matteo Vit, Sean Rickerd,
Andreas Färber, Rob Herring, Pawel Moll, Mark Rutland,
Ian Campbell, Kumar Gala, Russell King,
open list:OPEN FIRMWARE AND..., open list
Signed-off-by: Andreas Färber <afaerber@suse.de>
---
arch/arm/boot/dts/zynq-parallella1.dtsi | 118 ++++++++++++++++++++++++++++++++
1 file changed, 118 insertions(+)
diff --git a/arch/arm/boot/dts/zynq-parallella1.dtsi b/arch/arm/boot/dts/zynq-parallella1.dtsi
index 7c1206f928bc..e77a4968fe17 100644
--- a/arch/arm/boot/dts/zynq-parallella1.dtsi
+++ b/arch/arm/boot/dts/zynq-parallella1.dtsi
@@ -47,6 +47,8 @@
status = "okay";
phy-mode = "rgmii-id";
phy-handle = <ðernet_phy>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gem0_default>;
ethernet_phy: ethernet-phy@0 {
/* Marvell 88E1318 */
@@ -58,6 +60,11 @@
};
};
+&gpio0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio0_default>;
+};
+
&i2c0 {
status = "okay";
@@ -85,10 +92,121 @@
};
};
+&pinctrl0 {
+ pinctrl_gem0_default: gem0-default {
+ mux {
+ function = "ethernet0";
+ groups = "ethernet0_0_grp";
+ };
+
+ conf {
+ groups = "ethernet0_0_grp";
+ slew-rate = <0>;
+ io-standard = <1>;
+ };
+
+ conf-rx {
+ pins = "MIO22", "MIO23", "MIO24", "MIO25", "MIO26", "MIO27";
+ bias-high-impedance;
+ low-power-disable;
+ };
+
+ conf-tx {
+ pins = "MIO16", "MIO17", "MIO18", "MIO19", "MIO20", "MIO21";
+ bias-disable;
+ low-power-enable;
+ };
+
+ mux-mdio {
+ function = "mdio0";
+ groups = "mdio0_0_grp";
+ };
+
+ conf-mdio {
+ groups = "mdio0_0_grp";
+ slew-rate = <0>;
+ io-standard = <1>;
+ bias-disable;
+ };
+ };
+
+ pinctrl_gpio0_default: gpio0-default {
+ mux {
+ function = "gpio0";
+ groups = "gpio0_7_grp";
+ };
+
+ conf {
+ groups = "gpio0_7_grp";
+ slew-rate = <0>;
+ io-standard = <3>;
+ };
+
+ conf-pull-up {
+ pins = "MIO7";
+ bias-pull-up;
+ };
+ };
+
+ pinctrl_sdhci1_default: sdhci1-default {
+ mux {
+ function = "sdio1";
+ groups = "sdio1_0_grp";
+ };
+
+ conf {
+ groups = "sdio1_0_grp";
+ slew-rate = <0>;
+ io-standard = <1>;
+ bias-disable;
+ };
+
+ mux-cd {
+ function = "sdio1_cd";
+ groups = "gpio0_0_grp";
+ };
+
+ conf-cd {
+ groups = "gpio0_0_grp";
+ bias-high-impedance;
+ bias-pull-up;
+ slew-rate = <0>;
+ io-standard = <3>;
+ };
+ };
+
+ pinctrl_uart1_default: uart1-default {
+ mux {
+ function = "uart1";
+ groups = "uart1_0_grp";
+ };
+
+ conf {
+ groups = "uart1_0_grp";
+ slew-rate = <0>;
+ io-standard = <3>;
+ };
+
+ conf-rx {
+ pins = "MIO9";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO8";
+ bias-disable = <0>;
+ };
+ };
+};
+
&sdhci1 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sdhci1_default>;
};
&uart1 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1_default>;
};
--
2.2.2
^ permalink raw reply related [flat|nested] 6+ messages in thread* [PATCH 3/5] ARM: dts: zynq: Add LED for Parallella
[not found] <1423702513-4032-1-git-send-email-afaerber@suse.de>
[not found] ` <1423702513-4032-1-git-send-email-afaerber-l3A5Bk7waGM@public.gmane.org>
2015-02-12 0:55 ` [PATCH 2/5] ARM: dts: zynq: Add pinctrl to Parallella Andreas Färber
@ 2015-02-12 0:55 ` Andreas Färber
2015-02-12 0:55 ` [PATCH 4/5] ARM: dts: zynq: Split off Parallella Microserver device tree Andreas Färber
2015-02-12 0:55 ` [PATCH 5/5] ARM: dts: zynq: Add USB for Parallella Andreas Färber
4 siblings, 0 replies; 6+ messages in thread
From: Andreas Färber @ 2015-02-12 0:55 UTC (permalink / raw)
To: Michal Simek
Cc: Olof Johansson, Sören Brinkmann, linux-arm-kernel,
Andreas Olofsson, Ola Jeppsson, Matteo Vit, Sean Rickerd,
Andreas Färber, Rob Herring, Pawel Moll, Mark Rutland,
Ian Campbell, Kumar Gala, Russell King,
open list:OPEN FIRMWARE AND..., open list
This is the green LED CR10.
Signed-off-by: Andreas Färber <afaerber@suse.de>
---
arch/arm/boot/dts/zynq-parallella1.dtsi | 11 +++++++++++
1 file changed, 11 insertions(+)
diff --git a/arch/arm/boot/dts/zynq-parallella1.dtsi b/arch/arm/boot/dts/zynq-parallella1.dtsi
index e77a4968fe17..8b2895c06c8e 100644
--- a/arch/arm/boot/dts/zynq-parallella1.dtsi
+++ b/arch/arm/boot/dts/zynq-parallella1.dtsi
@@ -18,6 +18,7 @@
* GNU General Public License for more details.
*/
/include/ "zynq-7000.dtsi"
+#include <dt-bindings/gpio/gpio.h>
/ {
compatible = "adapteva,parallella", "xlnx,zynq-7000";
@@ -36,6 +37,16 @@
bootargs = "console=ttyPS0,115200 earlyprintk root=/dev/mmcblk0p2 rootfstype=ext4 rw rootwait";
linux,stdout-path = "/amba/serial@e0001000";
};
+
+ leds {
+ compatible = "gpio-leds";
+
+ cr10 {
+ label = "parallella:cr10:usr";
+ gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+ };
};
&clkc {
--
2.2.2
^ permalink raw reply related [flat|nested] 6+ messages in thread* [PATCH 4/5] ARM: dts: zynq: Split off Parallella Microserver device tree
[not found] <1423702513-4032-1-git-send-email-afaerber@suse.de>
` (2 preceding siblings ...)
2015-02-12 0:55 ` [PATCH 3/5] ARM: dts: zynq: Add LED for Parallella Andreas Färber
@ 2015-02-12 0:55 ` Andreas Färber
2015-02-12 13:12 ` Ola Jeppsson
2015-02-12 0:55 ` [PATCH 5/5] ARM: dts: zynq: Add USB for Parallella Andreas Färber
4 siblings, 1 reply; 6+ messages in thread
From: Andreas Färber @ 2015-02-12 0:55 UTC (permalink / raw)
To: Michal Simek
Cc: Olof Johansson, Sören Brinkmann, linux-arm-kernel,
Andreas Olofsson, Ola Jeppsson, Matteo Vit, Sean Rickerd,
Andreas Färber, Rob Herring, Pawel Moll, Mark Rutland,
Ian Campbell, Kumar Gala, Russell King,
open list:OPEN FIRMWARE AND..., open list
The Microserver edition has neither HDMI nor USB.
Cc: Ola Jeppsson <ola@adapteva.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/zynq-parallella-microserver.dts | 19 +++++++++++++++++++
2 files changed, 20 insertions(+)
create mode 100644 arch/arm/boot/dts/zynq-parallella-microserver.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index a1c776b8dcec..42c75eeba584 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -606,6 +606,7 @@ dtb-$(CONFIG_ARCH_VT8500) += \
wm8850-w70v2.dtb
dtb-$(CONFIG_ARCH_ZYNQ) += \
zynq-parallella.dtb \
+ zynq-parallella-microserver.dtb \
zynq-zc702.dtb \
zynq-zc706.dtb \
zynq-zed.dtb \
diff --git a/arch/arm/boot/dts/zynq-parallella-microserver.dts b/arch/arm/boot/dts/zynq-parallella-microserver.dts
new file mode 100644
index 000000000000..1f3bd2d27a93
--- /dev/null
+++ b/arch/arm/boot/dts/zynq-parallella-microserver.dts
@@ -0,0 +1,19 @@
+/*
+ * Copyright (c) 2014 SUSE LINUX Products GmbH
+ * Copyright (c) 2015 SUSE Linux GmbH
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+/dts-v1/;
+#include "zynq-parallella1.dtsi"
+
+/ {
+ model = "Adapteva Parallella Microserver Board";
+};
--
2.2.2
^ permalink raw reply related [flat|nested] 6+ messages in thread* Re: [PATCH 4/5] ARM: dts: zynq: Split off Parallella Microserver device tree
2015-02-12 0:55 ` [PATCH 4/5] ARM: dts: zynq: Split off Parallella Microserver device tree Andreas Färber
@ 2015-02-12 13:12 ` Ola Jeppsson
0 siblings, 0 replies; 6+ messages in thread
From: Ola Jeppsson @ 2015-02-12 13:12 UTC (permalink / raw)
To: Andreas Färber, Michal Simek
Cc: Olof Johansson, Sören Brinkmann, linux-arm-kernel,
Andreas Olofsson, Matteo Vit, Sean Rickerd, Rob Herring,
Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala, Russell King,
open list:OPEN FIRMWARE AND..., open list
On 2015-02-12 01:55, Andreas Färber wrote:
> The Microserver edition has neither HDMI nor USB.
>
> Cc: Ola Jeppsson <ola@adapteva.com>
> Signed-off-by: Andreas Färber <afaerber@suse.de>
> ---
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/zynq-parallella-microserver.dts | 19 +++++++++++++++++++
> 2 files changed, 20 insertions(+)
> create mode 100644 arch/arm/boot/dts/zynq-parallella-microserver.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index a1c776b8dcec..42c75eeba584 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -606,6 +606,7 @@ dtb-$(CONFIG_ARCH_VT8500) += \
> wm8850-w70v2.dtb
> dtb-$(CONFIG_ARCH_ZYNQ) += \
> zynq-parallella.dtb \
> + zynq-parallella-microserver.dtb \
> zynq-zc702.dtb \
> zynq-zc706.dtb \
> zynq-zed.dtb \
> diff --git a/arch/arm/boot/dts/zynq-parallella-microserver.dts b/arch/arm/boot/dts/zynq-parallella-microserver.dts
> new file mode 100644
> index 000000000000..1f3bd2d27a93
> --- /dev/null
> +++ b/arch/arm/boot/dts/zynq-parallella-microserver.dts
> @@ -0,0 +1,19 @@
> +/*
> + * Copyright (c) 2014 SUSE LINUX Products GmbH
> + * Copyright (c) 2015 SUSE Linux GmbH
> + *
> + * This software is licensed under the terms of the GNU General Public
> + * License version 2, as published by the Free Software Foundation, and
> + * may be copied, distributed, and modified under those terms.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +/dts-v1/;
> +#include "zynq-parallella1.dtsi"
> +
> +/ {
> + model = "Adapteva Parallella Microserver Board";
> +};
To me it would make more sense to use the model number in the file name.
I.e., p1600 instead of microserver.
http://www.digikey.com/product-search/en?v=1554&FV=fff40028%2Cfff8014d
// Ola
--
Phone: +46.733208642
Skype: olajep
Email: ola@adapteva.com
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH 5/5] ARM: dts: zynq: Add USB for Parallella
[not found] <1423702513-4032-1-git-send-email-afaerber@suse.de>
` (3 preceding siblings ...)
2015-02-12 0:55 ` [PATCH 4/5] ARM: dts: zynq: Split off Parallella Microserver device tree Andreas Färber
@ 2015-02-12 0:55 ` Andreas Färber
4 siblings, 0 replies; 6+ messages in thread
From: Andreas Färber @ 2015-02-12 0:55 UTC (permalink / raw)
To: Michal Simek
Cc: Olof Johansson, Sören Brinkmann, linux-arm-kernel,
Andreas Olofsson, Ola Jeppsson, Matteo Vit, Sean Rickerd,
Andreas Färber, Rob Herring, Pawel Moll, Mark Rutland,
Ian Campbell, Kumar Gala, Russell King,
open list:OPEN FIRMWARE AND..., open list
The Microserver edition does not feature USB - only the Kickstarter,
pre-order, Desktop and Embedded editions.
Signed-off-by: Andreas Färber <afaerber@suse.de>
---
arch/arm/boot/dts/zynq-parallella.dts | 16 +++++++
arch/arm/boot/dts/zynq-parallella1.dtsi | 74 +++++++++++++++++++++++++++++++++
2 files changed, 90 insertions(+)
diff --git a/arch/arm/boot/dts/zynq-parallella.dts b/arch/arm/boot/dts/zynq-parallella.dts
index 99ee6551ae8d..b2eede1c708f 100644
--- a/arch/arm/boot/dts/zynq-parallella.dts
+++ b/arch/arm/boot/dts/zynq-parallella.dts
@@ -17,3 +17,19 @@
/ {
model = "Adapteva Parallella Board";
};
+
+&usb_phy0 {
+ status = "okay";
+};
+
+&usb_phy1 {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+};
+
+&usb1 {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/zynq-parallella1.dtsi b/arch/arm/boot/dts/zynq-parallella1.dtsi
index 8b2895c06c8e..1395aaadf3be 100644
--- a/arch/arm/boot/dts/zynq-parallella1.dtsi
+++ b/arch/arm/boot/dts/zynq-parallella1.dtsi
@@ -47,6 +47,18 @@
default-state = "on";
};
};
+
+ usb_phy0: phy0 {
+ compatible = "usb-nop-xceiv";
+ #phy-cells = <0>;
+ status = "disabled";
+ };
+
+ usb_phy1: phy1 {
+ compatible = "usb-nop-xceiv";
+ #phy-cells = <0>;
+ status = "disabled";
+ };
};
&clkc {
@@ -208,6 +220,54 @@
bias-disable = <0>;
};
};
+
+ pinctrl_usb0_default: usb0-default {
+ mux {
+ function = "usb0";
+ groups = "usb0_0_grp";
+ };
+
+ conf {
+ groups = "usb0_0_grp";
+ slew-rate = <0>;
+ io-standard = <1>;
+ };
+
+ conf-rx {
+ pins = "MIO29", "MIO31", "MIO36";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO28", "MIO30", "MIO32", "MIO33", "MIO34",
+ "MIO35", "MIO37", "MIO38", "MIO39";
+ bias-disable;
+ };
+ };
+
+ pinctrl_usb1_default: usb1-default {
+ mux {
+ function = "usb1";
+ groups = "usb1_0_grp";
+ };
+
+ conf {
+ groups = "usb1_0_grp";
+ slew-rate = <0>;
+ io-standard = <1>;
+ };
+
+ conf-rx {
+ pins = "MIO41", "MIO43", "MIO48";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO40", "MIO42", "MIO44", "MIO45", "MIO46",
+ "MIO47", "MIO49", "MIO50", "MIO51";
+ bias-disable;
+ };
+ };
};
&sdhci1 {
@@ -221,3 +281,17 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1_default>;
};
+
+&usb0 {
+ dr_mode = "host";
+ usb-phy = <&usb_phy0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb0_default>;
+};
+
+&usb1 {
+ dr_mode = "peripheral";
+ usb-phy = <&usb_phy1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb1_default>;
+};
--
2.2.2
^ permalink raw reply related [flat|nested] 6+ messages in thread
end of thread, other threads:[~2015-02-12 13:12 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <1423702513-4032-1-git-send-email-afaerber@suse.de>
[not found] ` <1423702513-4032-1-git-send-email-afaerber-l3A5Bk7waGM@public.gmane.org>
2015-02-12 0:55 ` [PATCH 1/5] ARM: dts: zynq: Split out common Parallella bits Andreas Färber
2015-02-12 0:55 ` [PATCH 2/5] ARM: dts: zynq: Add pinctrl to Parallella Andreas Färber
2015-02-12 0:55 ` [PATCH 3/5] ARM: dts: zynq: Add LED for Parallella Andreas Färber
2015-02-12 0:55 ` [PATCH 4/5] ARM: dts: zynq: Split off Parallella Microserver device tree Andreas Färber
2015-02-12 13:12 ` Ola Jeppsson
2015-02-12 0:55 ` [PATCH 5/5] ARM: dts: zynq: Add USB for Parallella Andreas Färber
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).