* [PATCH 0/2] add dts for PopMetal board
@ 2015-02-27 10:55 Andy Yan
2015-02-27 10:59 ` [PATCH 1/2] dt-bindings: add root compatible property " Andy Yan
[not found] ` <1425034505-25163-1-git-send-email-andy.yan-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
0 siblings, 2 replies; 7+ messages in thread
From: Andy Yan @ 2015-02-27 10:55 UTC (permalink / raw)
To: heiko, devicetree
Cc: mark.rutland, linux, pawel.moll, ijc+devicetree, linux-kernel,
naobsd, b.galvani, linux-rockchip, robh+dt, galak, Andy Yan,
romain.perier, linux-arm-kernel, mark.yao
PopMetal is a rockchip rk3288 based board made by ChipSpark,
which has many interface such as VGA,HDMI,usb,ir,sdcad and lots of
sensors such as gyroscope(L3G4200D),accelerometer(mma8452),compass(AK8963C).
http://wiki.chipspark.com/en/index.php?title=PopMetal
This patch add basic support for it. More feather will be enabled later.
Andy Yan (2):
dt-bindings: add root compatible property for PopMetal board
ARM: dts: add rk3288 PopMetal board
Documentation/devicetree/bindings/arm/rockchip.txt | 4 +
arch/arm/boot/dts/rk3288-popmetal.dts | 396 +++++++++++++++++++++
2 files changed, 400 insertions(+)
create mode 100644 arch/arm/boot/dts/rk3288-popmetal.dts
--
1.9.1
^ permalink raw reply [flat|nested] 7+ messages in thread* [PATCH 1/2] dt-bindings: add root compatible property for PopMetal board 2015-02-27 10:55 [PATCH 0/2] add dts for PopMetal board Andy Yan @ 2015-02-27 10:59 ` Andy Yan 2015-02-28 17:43 ` Heiko Stübner [not found] ` <1425034505-25163-1-git-send-email-andy.yan-TNX95d0MmH7DzftRWevZcw@public.gmane.org> 1 sibling, 1 reply; 7+ messages in thread From: Andy Yan @ 2015-02-27 10:59 UTC (permalink / raw) To: heiko, devicetree Cc: mark.rutland, linux, pawel.moll, ijc+devicetree, linux-kernel, naobsd, b.galvani, linux-rockchip, robh+dt, galak, Andy Yan, romain.perier, linux-arm-kernel, mark.yao PopMetal board is a rk3288 based board made by ChipSpark, this patch add root compatible property for it Signed-off-by: Andy Yan <andy.yan@rock-chips.com> --- Documentation/devicetree/bindings/arm/rockchip.txt | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt index 6809e4e..818d249 100644 --- a/Documentation/devicetree/bindings/arm/rockchip.txt +++ b/Documentation/devicetree/bindings/arm/rockchip.txt @@ -22,3 +22,7 @@ Rockchip platforms device tree bindings - compatible = "firefly,firefly-rk3288", "rockchip,rk3288"; or - compatible = "firefly,firefly-rk3288-beta", "rockchip,rk3288"; + +- PopMetal PopMetal-RK3288 board: + Required root node properties: + - compatible = "chipspark,popmetal-rk3288", "rockchip,rk3288"; -- 1.9.1 ^ permalink raw reply related [flat|nested] 7+ messages in thread
* Re: [PATCH 1/2] dt-bindings: add root compatible property for PopMetal board 2015-02-27 10:59 ` [PATCH 1/2] dt-bindings: add root compatible property " Andy Yan @ 2015-02-28 17:43 ` Heiko Stübner 2015-03-01 6:49 ` Andy Yan 0 siblings, 1 reply; 7+ messages in thread From: Heiko Stübner @ 2015-02-28 17:43 UTC (permalink / raw) To: Andy Yan Cc: mark.rutland, devicetree, linux, pawel.moll, ijc+devicetree, linux-kernel, naobsd, b.galvani, linux-rockchip, robh+dt, galak, romain.perier, linux-arm-kernel, mark.yao Hi Andy, Am Freitag, 27. Februar 2015, 18:59:01 schrieb Andy Yan: > PopMetal board is a rk3288 based board made by ChipSpark, > this patch add root compatible property for it > > Signed-off-by: Andy Yan <andy.yan@rock-chips.com> > > --- > > Documentation/devicetree/bindings/arm/rockchip.txt | 4 ++++ > 1 file changed, 4 insertions(+) > > diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt > b/Documentation/devicetree/bindings/arm/rockchip.txt index 6809e4e..818d249 > 100644 > --- a/Documentation/devicetree/bindings/arm/rockchip.txt > +++ b/Documentation/devicetree/bindings/arm/rockchip.txt > @@ -22,3 +22,7 @@ Rockchip platforms device tree bindings > - compatible = "firefly,firefly-rk3288", "rockchip,rk3288"; > or > - compatible = "firefly,firefly-rk3288-beta", "rockchip,rk3288"; > + > +- PopMetal PopMetal-RK3288 board: this should probably be ChipSPARK PopMetal-RK3288 board: > + Required root node properties: > + - compatible = "chipspark,popmetal-rk3288", "rockchip,rk3288"; ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH 1/2] dt-bindings: add root compatible property for PopMetal board 2015-02-28 17:43 ` Heiko Stübner @ 2015-03-01 6:49 ` Andy Yan 0 siblings, 0 replies; 7+ messages in thread From: Andy Yan @ 2015-03-01 6:49 UTC (permalink / raw) To: Heiko Stübner Cc: devicetree, naobsd, romain.perier, b.galvani, galak, linux-kernel, ijc+devicetree, linux-rockchip, robh+dt, pawel.moll, mark.rutland, linux, linux-arm-kernel, mark.yao Hi Heiko: On 2015年03月01日 01:43, Heiko Stübner wrote: > Hi Andy, > > Am Freitag, 27. Februar 2015, 18:59:01 schrieb Andy Yan: >> PopMetal board is a rk3288 based board made by ChipSpark, >> this patch add root compatible property for it >> >> Signed-off-by: Andy Yan <andy.yan@rock-chips.com> >> >> --- >> >> Documentation/devicetree/bindings/arm/rockchip.txt | 4 ++++ >> 1 file changed, 4 insertions(+) >> >> diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt >> b/Documentation/devicetree/bindings/arm/rockchip.txt index 6809e4e..818d249 >> 100644 >> --- a/Documentation/devicetree/bindings/arm/rockchip.txt >> +++ b/Documentation/devicetree/bindings/arm/rockchip.txt >> @@ -22,3 +22,7 @@ Rockchip platforms device tree bindings >> - compatible = "firefly,firefly-rk3288", "rockchip,rk3288"; >> or >> - compatible = "firefly,firefly-rk3288-beta", "rockchip,rk3288"; >> + >> +- PopMetal PopMetal-RK3288 board: > this should probably be > ChipSPARK PopMetal-RK3288 board: ok, this will be fixed in V2 > > >> + Required root node properties: >> + - compatible = "chipspark,popmetal-rk3288", "rockchip,rk3288"; > > > ^ permalink raw reply [flat|nested] 7+ messages in thread
[parent not found: <1425034505-25163-1-git-send-email-andy.yan-TNX95d0MmH7DzftRWevZcw@public.gmane.org>]
* [PATCH 2/2] ARM: dts: add rk3288 PopMetal board [not found] ` <1425034505-25163-1-git-send-email-andy.yan-TNX95d0MmH7DzftRWevZcw@public.gmane.org> @ 2015-02-27 11:03 ` Andy Yan 2015-02-28 17:57 ` Heiko Stübner 0 siblings, 1 reply; 7+ messages in thread From: Andy Yan @ 2015-02-27 11:03 UTC (permalink / raw) To: heiko-4mtYJXux2i+zQB+pC5nmwQ, devicetree-u79uwXL29TY76Z2rM5mHXA Cc: naobsd-Re5JQEeQqe8AvxtiuMwx3w, romain.perier-Re5JQEeQqe8AvxtiuMwx3w, b.galvani-Re5JQEeQqe8AvxtiuMwx3w, galak-sgV2jX0FEOL9JmXXK+q4OQ, linux-kernel-u79uwXL29TY76Z2rM5mHXA, ijc+devicetree-KcIKpvwj1kUDXYZnReoRVg, linux-rockchip-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, robh+dt-DgEjT+Ai2ygdnm+yROfE0A, pawel.moll-5wv7dgnIgG8, mark.rutland-5wv7dgnIgG8, linux-lFZ/pmaqli7XmaaqVzeoHQ, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, mark.yao-TNX95d0MmH7DzftRWevZcw, Andy Yan PopMetal is a rockchip rk3288 based board made by ChipSpark, which has many interface such as VGA,HDMI,usb,ir,sdcad and lots of sensors such as gyroscope(L3G4200D),accelerometer(mma8452), compass(AK8963C). This patch add a basic support for this board, which make the board boot into a initramfs shell with sdcard and all sensors enabled Signed-off-by: Andy Yan <andy.yan-TNX95d0MmH7DzftRWevZcw@public.gmane.org> --- arch/arm/boot/dts/rk3288-popmetal.dts | 396 ++++++++++++++++++++++++++++++++++ 1 file changed, 396 insertions(+) create mode 100644 arch/arm/boot/dts/rk3288-popmetal.dts diff --git a/arch/arm/boot/dts/rk3288-popmetal.dts b/arch/arm/boot/dts/rk3288-popmetal.dts new file mode 100644 index 0000000..f0c0cd9 --- /dev/null +++ b/arch/arm/boot/dts/rk3288-popmetal.dts @@ -0,0 +1,396 @@ +/* + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +/dts-v1/; + +#include "rk3288.dtsi" + +/ { + model = "PopMetal-RK3288"; + compatible = "chipspark,popmetal-rk3288", "rockchip,rk3288"; + memory{ + reg = <0 0x80000000>; + }; + + ext_gmac: external-gmac-clock { + compatible = "fixed-clock"; + clock-frequency = <125000000>; + clock-output-names = "ext_gmac"; + #clock-cells = <0>; + }; + + gpio-keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + autorepeat; + + pinctrl-names = "default"; + pinctrl-0 = <&pwrbtn>; + + button@0 { + gpios = <&gpio0 5 GPIO_ACTIVE_LOW>; + linux,code = <116>; + label = "GPIO Key Power"; + linux,input-type = <1>; + gpio-key,wakeup = <1>; + debounce-interval = <100>; + }; + }; + + ir: ir-receiver { + compatible = "gpio-ir-receiver"; + gpios = <&gpio0 6 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&ir_int>; + }; + +}; + +&emmc { + broken-cd; + bus-width = <8>; + cap-mmc-highspeed; + disable-wp; + non-removable; + num-slots = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_pwr &emmc_bus8>; + status = "okay"; +}; + +&sdmmc { + bus-width = <4>; + cap-mmc-highspeed; + cap-sd-highspeed; + card-detect-delay = <200>; + disable-wp; /* wp not hooked up */ + num-slots = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>; + status = "okay"; +}; + +&gmac { + phy-supply = <&vcc_lan>; + phy-mode = "rgmii"; + clock_in_out = "input"; + snps,reset-gpio = <&gpio4 7 0>; + snps,reset-active-low; + snps,reset-delays-us = <0 10000 1000000>; + assigned-clocks = <&cru SCLK_MAC>; + assigned-clock-parents = <&ext_gmac>; + pinctrl-names = "default"; + pinctrl-0 = <&rgmii_pins>; + tx_delay = <0x30>; + rx_delay = <0x10>; + status = "ok"; +}; + +&hdmi { + ddc-i2c-bus = <&i2c5>; + status = "okay"; +}; + +&i2c0 { + status = "okay"; + clock-frequency = <400000>; + + rk808: pmic@1b { + compatible = "rockchip,rk808"; + reg = <0x1b>; + interrupt-parent = <&gpio0>; + interrupts = <4 IRQ_TYPE_LEVEL_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&pmic_int &global_pwroff>; + rockchip,system-power-controller; + wakeup-source; + #clock-cells = <1>; + clock-output-names = "xin32k", "rk808-clkout2"; + + vcc8-supply = <&vcc_18>; + vcc9-supply = <&vcc_io>; + vcc10-supply = <&vcc_io>; + vcc12-supply = <&vcc_io>; + + regulators { + vdd_cpu: DCDC_REG1 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <1350000>; + regulator-name = "vdd_arm"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdd_gpu: DCDC_REG2 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1250000>; + regulator-name = "vdd_gpu"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1000000>; + }; + }; + + vcc_ddr: DCDC_REG3 { + regulator-always-on; + regulator-boot-on; + regulator-name = "vcc_ddr"; + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + + vcc_io: DCDC_REG4 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc_io"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <3300000>; + }; + }; + + vcc_lan: LDO_REG1 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc_lan"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <3300000>; + }; + }; + + vccio_sd: LDO_REG2 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vccio_sd"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdd_10: LDO_REG3 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-name = "vdd_10"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1000000>; + }; + }; + + vcc18_lcd: LDO_REG4 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc18_lcd"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1800000>; + }; + }; + + ldo5: LDO_REG5 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-name = "ldo5"; + }; + + vdd10_lcd: LDO_REG6 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-name = "vdd10_lcd"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1000000>; + }; + }; + + vcc_18: LDO_REG7 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc_18"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1800000>; + }; + }; + + vcca_codec: LDO_REG8 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcca_codec"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <3300000>; + }; + }; + + vcc_wl: SWITCH_REG1 { + regulator-always-on; + regulator-boot-on; + regulator-name = "vcc_wl"; + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + + vcc_lcd: SWITCH_REG2 { + regulator-always-on; + regulator-boot-on; + regulator-name = "vcc_lcd"; + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + }; + }; +}; + +&i2c1 { + status = "okay"; + clock-frequency = <400000>; + + ak8963: ak8963@0d { + compatible = "asahi-kasei,ak8975"; + reg = <0x0d>; + interrupt-parent = <&gpio8>; + interrupts = <1 IRQ_TYPE_EDGE_RISING>; + pinctrl-names = "default"; + pinctrl-0 = <&comp_int>; + }; + + l3g4200d: l3g4200d@68 { + compatible = "st,l3g4200d-gyro"; + st,drdy-int-pin = <2>; + reg = <0x6b>; + }; + + mma8452: mma8452@1d { + compatible = "fsl,mma8452"; + reg = <0x1d>; + interrupt-parent = <&gpio8>; + interrupts = <0 IRQ_TYPE_EDGE_RISING>; + pinctrl-names = "default"; + pinctrl-0 = <&gsensor_int>; + }; +}; + +&i2c2 { + status = "okay"; +}; + +&i2c3 { + status = "okay"; +}; + +&i2c4 { + status = "okay"; +}; + +&i2c5 { + status = "okay"; +}; + +&pinctrl { + buttons { + pwrbtn: pwrbtn { + rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + ak8963 { + comp_int: comp-int { + rockchip,pins = <8 1 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + ir { + ir_int: ir-int { + rockchip,pins = <0 6 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + mma8452 { + gsensor_int: gsensor-int { + rockchip,pins = <8 0 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + pmic { + pmic_int: pmic-int { + rockchip,pins = <RK_GPIO0 4 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; +}; + +&vopb { + status = "okay"; +}; + +&vopb_mmu { + status = "okay"; +}; + +&vopl { + status = "okay"; +}; + +&vopl_mmu { + status = "okay"; +}; + +&uart0 { + status = "okay"; +}; + +&uart1 { + status = "okay"; +}; + +&uart2 { + status = "okay"; +}; + +&uart3 { + status = "okay"; +}; + +&uart4 { + status = "okay"; +}; + +&usbphy { + status = "okay"; +}; -- 1.9.1 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply related [flat|nested] 7+ messages in thread
* Re: [PATCH 2/2] ARM: dts: add rk3288 PopMetal board 2015-02-27 11:03 ` [PATCH 2/2] ARM: dts: add rk3288 " Andy Yan @ 2015-02-28 17:57 ` Heiko Stübner 2015-03-01 7:27 ` Andy Yan 0 siblings, 1 reply; 7+ messages in thread From: Heiko Stübner @ 2015-02-28 17:57 UTC (permalink / raw) To: Andy Yan Cc: devicetree, naobsd, romain.perier, b.galvani, galak, linux-kernel, ijc+devicetree, linux-rockchip, robh+dt, pawel.moll, mark.rutland, linux, linux-arm-kernel, mark.yao Hi Andy, Am Freitag, 27. Februar 2015, 19:03:03 schrieb Andy Yan: > PopMetal is a rockchip rk3288 based board made by ChipSpark, > which has many interface such as VGA,HDMI,usb,ir,sdcad and > lots of sensors such as gyroscope(L3G4200D),accelerometer(mma8452), > compass(AK8963C). > > This patch add a basic support for this board, which make the board > boot into a initramfs shell with sdcard and all sensors enabled > > Signed-off-by: Andy Yan <andy.yan@rock-chips.com> > --- > > arch/arm/boot/dts/rk3288-popmetal.dts | 396 > ++++++++++++++++++++++++++++++++++ 1 file changed, 396 insertions(+) > create mode 100644 arch/arm/boot/dts/rk3288-popmetal.dts > > diff --git a/arch/arm/boot/dts/rk3288-popmetal.dts > b/arch/arm/boot/dts/rk3288-popmetal.dts new file mode 100644 > index 0000000..f0c0cd9 > --- /dev/null > +++ b/arch/arm/boot/dts/rk3288-popmetal.dts > @@ -0,0 +1,396 @@ > +/* > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License as published by > + * the Free Software Foundation; either version 2 of the License, or > + * (at your option) any later version. > + * > + * This program is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. could you please put the new file under a gpl2+x11 dual license? See the firefly dts files for an example. Relicensing the of the already existing files is somewhere on my todo list, but but at least we shouldn't introduce new restricted files at this point :-) . Licensing with a more permissible license is necessary so that other projects can use our dts files too (like the BSDs) and the gpl2 + x11 dual license is the current agreed upon combination. > + */ > + > +/dts-v1/; > + > +#include "rk3288.dtsi" > + > +/ { > + model = "PopMetal-RK3288"; > + compatible = "chipspark,popmetal-rk3288", "rockchip,rk3288"; a blank line here please > + memory{ > + reg = <0 0x80000000>; > + }; > + > + ext_gmac: external-gmac-clock { > + compatible = "fixed-clock"; > + clock-frequency = <125000000>; > + clock-output-names = "ext_gmac"; > + #clock-cells = <0>; > + }; > + > + gpio-keys { > + compatible = "gpio-keys"; > + #address-cells = <1>; > + #size-cells = <0>; > + autorepeat; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&pwrbtn>; > + > + button@0 { > + gpios = <&gpio0 5 GPIO_ACTIVE_LOW>; > + linux,code = <116>; > + label = "GPIO Key Power"; > + linux,input-type = <1>; > + gpio-key,wakeup = <1>; > + debounce-interval = <100>; > + }; > + }; > + > + ir: ir-receiver { > + compatible = "gpio-ir-receiver"; > + gpios = <&gpio0 6 GPIO_ACTIVE_LOW>; > + pinctrl-names = "default"; > + pinctrl-0 = <&ir_int>; > + }; > + > +}; > + > +&emmc { > + broken-cd; > + bus-width = <8>; > + cap-mmc-highspeed; > + disable-wp; > + non-removable; > + num-slots = <1>; > + pinctrl-names = "default"; > + pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_pwr &emmc_bus8>; > + status = "okay"; > +}; > + > +&sdmmc { > + bus-width = <4>; > + cap-mmc-highspeed; > + cap-sd-highspeed; > + card-detect-delay = <200>; > + disable-wp; /* wp not hooked up */ > + num-slots = <1>; > + pinctrl-names = "default"; > + pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>; > + status = "okay"; > +}; > + > +&gmac { > + phy-supply = <&vcc_lan>; > + phy-mode = "rgmii"; > + clock_in_out = "input"; > + snps,reset-gpio = <&gpio4 7 0>; > + snps,reset-active-low; > + snps,reset-delays-us = <0 10000 1000000>; > + assigned-clocks = <&cru SCLK_MAC>; > + assigned-clock-parents = <&ext_gmac>; > + pinctrl-names = "default"; > + pinctrl-0 = <&rgmii_pins>; > + tx_delay = <0x30>; > + rx_delay = <0x10>; > + status = "ok"; > +}; > + > +&hdmi { > + ddc-i2c-bus = <&i2c5>; > + status = "okay"; > +}; > + > +&i2c0 { > + status = "okay"; > + clock-frequency = <400000>; > + > + rk808: pmic@1b { > + compatible = "rockchip,rk808"; > + reg = <0x1b>; > + interrupt-parent = <&gpio0>; > + interrupts = <4 IRQ_TYPE_LEVEL_LOW>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pmic_int &global_pwroff>; > + rockchip,system-power-controller; > + wakeup-source; > + #clock-cells = <1>; > + clock-output-names = "xin32k", "rk808-clkout2"; > + > + vcc8-supply = <&vcc_18>; > + vcc9-supply = <&vcc_io>; > + vcc10-supply = <&vcc_io>; > + vcc12-supply = <&vcc_io>; > + > + regulators { > + vdd_cpu: DCDC_REG1 { > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <750000>; > + regulator-max-microvolt = <1350000>; > + regulator-name = "vdd_arm"; > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + vdd_gpu: DCDC_REG2 { > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <850000>; > + regulator-max-microvolt = <1250000>; > + regulator-name = "vdd_gpu"; > + regulator-state-mem { > + regulator-on-in-suspend; > + regulator-suspend-microvolt = <1000000>; > + }; > + }; > + > + vcc_ddr: DCDC_REG3 { > + regulator-always-on; > + regulator-boot-on; > + regulator-name = "vcc_ddr"; > + regulator-state-mem { > + regulator-on-in-suspend; > + }; > + }; > + > + vcc_io: DCDC_REG4 { > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "vcc_io"; > + regulator-state-mem { > + regulator-on-in-suspend; > + regulator-suspend-microvolt = <3300000>; > + }; > + }; > + > + vcc_lan: LDO_REG1 { > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "vcc_lan"; > + regulator-state-mem { > + regulator-on-in-suspend; > + regulator-suspend-microvolt = <3300000>; > + }; > + }; > + > + vccio_sd: LDO_REG2 { > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "vccio_sd"; > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + vdd_10: LDO_REG3 { > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <1000000>; > + regulator-max-microvolt = <1000000>; > + regulator-name = "vdd_10"; > + regulator-state-mem { > + regulator-on-in-suspend; > + regulator-suspend-microvolt = <1000000>; > + }; > + }; > + > + vcc18_lcd: LDO_REG4 { > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-name = "vcc18_lcd"; > + regulator-state-mem { > + regulator-on-in-suspend; > + regulator-suspend-microvolt = <1800000>; > + }; > + }; > + > + ldo5: LDO_REG5 { > + regulator-always-on; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "ldo5"; > + }; > + > + vdd10_lcd: LDO_REG6 { > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <1000000>; > + regulator-max-microvolt = <1000000>; > + regulator-name = "vdd10_lcd"; > + regulator-state-mem { > + regulator-on-in-suspend; > + regulator-suspend-microvolt = <1000000>; > + }; > + }; > + > + vcc_18: LDO_REG7 { > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-name = "vcc_18"; > + regulator-state-mem { > + regulator-on-in-suspend; > + regulator-suspend-microvolt = <1800000>; > + }; > + }; > + > + vcca_codec: LDO_REG8 { > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "vcca_codec"; > + regulator-state-mem { > + regulator-on-in-suspend; > + regulator-suspend-microvolt = <3300000>; > + }; > + }; > + > + vcc_wl: SWITCH_REG1 { > + regulator-always-on; > + regulator-boot-on; > + regulator-name = "vcc_wl"; > + regulator-state-mem { > + regulator-on-in-suspend; > + }; > + }; > + > + vcc_lcd: SWITCH_REG2 { > + regulator-always-on; > + regulator-boot-on; > + regulator-name = "vcc_lcd"; > + regulator-state-mem { > + regulator-on-in-suspend; > + }; > + }; only for my peace of mind, does the board wake again from suspend with these rk808 settings? I.e. while I my rk3288-evb-rk808 wakes sucessfully, I haven't been able to wake an act8846 based board (firefly) yet. > + }; > + }; > +}; > + > +&i2c1 { > + status = "okay"; > + clock-frequency = <400000>; > + > + ak8963: ak8963@0d { > + compatible = "asahi-kasei,ak8975"; > + reg = <0x0d>; > + interrupt-parent = <&gpio8>; > + interrupts = <1 IRQ_TYPE_EDGE_RISING>; > + pinctrl-names = "default"; > + pinctrl-0 = <&comp_int>; > + }; > + > + l3g4200d: l3g4200d@68 { > + compatible = "st,l3g4200d-gyro"; > + st,drdy-int-pin = <2>; > + reg = <0x6b>; > + }; > + > + mma8452: mma8452@1d { > + compatible = "fsl,mma8452"; > + reg = <0x1d>; > + interrupt-parent = <&gpio8>; > + interrupts = <0 IRQ_TYPE_EDGE_RISING>; > + pinctrl-names = "default"; > + pinctrl-0 = <&gsensor_int>; > + }; > +}; > + > +&i2c2 { > + status = "okay"; > +}; > + > +&i2c3 { > + status = "okay"; > +}; > + > +&i2c4 { > + status = "okay"; > +}; > + > +&i2c5 { > + status = "okay"; > +}; > + > +&pinctrl { > + buttons { > + pwrbtn: pwrbtn { > + rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_up>; > + }; pwrbtn needs one indentation more. Also please sort alphabetically ... "ak8963" before "buttons" > + }; > + > + ak8963 { > + comp_int: comp-int { > + rockchip,pins = <8 1 RK_FUNC_GPIO &pcfg_pull_up>; > + }; > + }; > + > + ir { > + ir_int: ir-int { > + rockchip,pins = <0 6 RK_FUNC_GPIO &pcfg_pull_up>; > + }; > + }; > + > + mma8452 { > + gsensor_int: gsensor-int { > + rockchip,pins = <8 0 RK_FUNC_GPIO &pcfg_pull_up>; > + }; > + }; > + > + pmic { > + pmic_int: pmic-int { > + rockchip,pins = <RK_GPIO0 4 RK_FUNC_GPIO &pcfg_pull_up>; > + }; > + }; > +}; > + > +&vopb { > + status = "okay"; > +}; > + > +&vopb_mmu { > + status = "okay"; > +}; > + > +&vopl { > + status = "okay"; > +}; > + > +&vopl_mmu { > + status = "okay"; > +}; > + > +&uart0 { > + status = "okay"; > +}; > + > +&uart1 { > + status = "okay"; > +}; > + > +&uart2 { > + status = "okay"; > +}; > + > +&uart3 { > + status = "okay"; > +}; > + > +&uart4 { > + status = "okay"; > +}; > + > +&usbphy { > + status = "okay"; > +}; in general looks good. Because of the license issue I need you to submit a v2, otherwise I could have fixed the small nitpicks myself. Heiko ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH 2/2] ARM: dts: add rk3288 PopMetal board 2015-02-28 17:57 ` Heiko Stübner @ 2015-03-01 7:27 ` Andy Yan 0 siblings, 0 replies; 7+ messages in thread From: Andy Yan @ 2015-03-01 7:27 UTC (permalink / raw) To: Heiko Stübner Cc: devicetree-u79uwXL29TY76Z2rM5mHXA, naobsd-Re5JQEeQqe8AvxtiuMwx3w, romain.perier-Re5JQEeQqe8AvxtiuMwx3w, b.galvani-Re5JQEeQqe8AvxtiuMwx3w, galak-sgV2jX0FEOL9JmXXK+q4OQ, linux-kernel-u79uwXL29TY76Z2rM5mHXA, ijc+devicetree-KcIKpvwj1kUDXYZnReoRVg, linux-rockchip-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, robh+dt-DgEjT+Ai2ygdnm+yROfE0A, pawel.moll-5wv7dgnIgG8, mark.rutland-5wv7dgnIgG8, linux-lFZ/pmaqli7XmaaqVzeoHQ, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, mark.yao-TNX95d0MmH7DzftRWevZcw Hi Heiko: On 2015年03月01日 01:57, Heiko Stübner wrote: > Hi Andy, > > Am Freitag, 27. Februar 2015, 19:03:03 schrieb Andy Yan: >> PopMetal is a rockchip rk3288 based board made by ChipSpark, >> which has many interface such as VGA,HDMI,usb,ir,sdcad and >> lots of sensors such as gyroscope(L3G4200D),accelerometer(mma8452), >> compass(AK8963C). >> >> This patch add a basic support for this board, which make the board >> boot into a initramfs shell with sdcard and all sensors enabled >> >> Signed-off-by: Andy Yan <andy.yan-TNX95d0MmH7DzftRWevZcw@public.gmane.org> >> --- >> >> arch/arm/boot/dts/rk3288-popmetal.dts | 396 >> ++++++++++++++++++++++++++++++++++ 1 file changed, 396 insertions(+) >> create mode 100644 arch/arm/boot/dts/rk3288-popmetal.dts >> >> diff --git a/arch/arm/boot/dts/rk3288-popmetal.dts >> b/arch/arm/boot/dts/rk3288-popmetal.dts new file mode 100644 >> index 0000000..f0c0cd9 >> --- /dev/null >> +++ b/arch/arm/boot/dts/rk3288-popmetal.dts >> @@ -0,0 +1,396 @@ >> +/* >> + * This program is free software; you can redistribute it and/or modify >> + * it under the terms of the GNU General Public License as published by >> + * the Free Software Foundation; either version 2 of the License, or >> + * (at your option) any later version. >> + * >> + * This program is distributed in the hope that it will be useful, >> + * but WITHOUT ANY WARRANTY; without even the implied warranty of >> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the >> + * GNU General Public License for more details. > could you please put the new file under a gpl2+x11 dual license? > See the firefly dts files for an example. > > Relicensing the of the already existing files is somewhere on my todo list, but > but at least we shouldn't introduce new restricted files at this point :-) . > > > Licensing with a more permissible license is necessary so that other projects > can use our dts files too (like the BSDs) and the gpl2 + x11 dual license is > the current agreed upon combination. ok, I will use gpl2+x11 dual license > >> + */ >> + >> +/dts-v1/; >> + >> +#include "rk3288.dtsi" >> + >> +/ { >> + model = "PopMetal-RK3288"; >> + compatible = "chipspark,popmetal-rk3288", "rockchip,rk3288"; > a blank line here please ok > >> + memory{ >> + reg = <0 0x80000000>; >> + }; >> + >> + ext_gmac: external-gmac-clock { >> + compatible = "fixed-clock"; >> + clock-frequency = <125000000>; >> + clock-output-names = "ext_gmac"; >> + #clock-cells = <0>; >> + }; >> + >> + gpio-keys { >> + compatible = "gpio-keys"; >> + #address-cells = <1>; >> + #size-cells = <0>; >> + autorepeat; >> + >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pwrbtn>; >> + >> + button@0 { >> + gpios = <&gpio0 5 GPIO_ACTIVE_LOW>; >> + linux,code = <116>; >> + label = "GPIO Key Power"; >> + linux,input-type = <1>; >> + gpio-key,wakeup = <1>; >> + debounce-interval = <100>; >> + }; >> + }; >> + >> + ir: ir-receiver { >> + compatible = "gpio-ir-receiver"; >> + gpios = <&gpio0 6 GPIO_ACTIVE_LOW>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&ir_int>; >> + }; >> + >> +}; >> + >> +&emmc { >> + broken-cd; >> + bus-width = <8>; >> + cap-mmc-highspeed; >> + disable-wp; >> + non-removable; >> + num-slots = <1>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_pwr &emmc_bus8>; >> + status = "okay"; >> +}; >> + >> +&sdmmc { >> + bus-width = <4>; >> + cap-mmc-highspeed; >> + cap-sd-highspeed; >> + card-detect-delay = <200>; >> + disable-wp; /* wp not hooked up */ >> + num-slots = <1>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>; >> + status = "okay"; >> +}; >> + >> +&gmac { >> + phy-supply = <&vcc_lan>; >> + phy-mode = "rgmii"; >> + clock_in_out = "input"; >> + snps,reset-gpio = <&gpio4 7 0>; >> + snps,reset-active-low; >> + snps,reset-delays-us = <0 10000 1000000>; >> + assigned-clocks = <&cru SCLK_MAC>; >> + assigned-clock-parents = <&ext_gmac>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&rgmii_pins>; >> + tx_delay = <0x30>; >> + rx_delay = <0x10>; >> + status = "ok"; >> +}; >> + >> +&hdmi { >> + ddc-i2c-bus = <&i2c5>; >> + status = "okay"; >> +}; >> + >> +&i2c0 { >> + status = "okay"; >> + clock-frequency = <400000>; >> + >> + rk808: pmic@1b { >> + compatible = "rockchip,rk808"; >> + reg = <0x1b>; >> + interrupt-parent = <&gpio0>; >> + interrupts = <4 IRQ_TYPE_LEVEL_LOW>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pmic_int &global_pwroff>; >> + rockchip,system-power-controller; >> + wakeup-source; >> + #clock-cells = <1>; >> + clock-output-names = "xin32k", "rk808-clkout2"; >> + >> + vcc8-supply = <&vcc_18>; >> + vcc9-supply = <&vcc_io>; >> + vcc10-supply = <&vcc_io>; >> + vcc12-supply = <&vcc_io>; >> + >> + regulators { >> + vdd_cpu: DCDC_REG1 { >> + regulator-always-on; >> + regulator-boot-on; >> + regulator-min-microvolt = <750000>; >> + regulator-max-microvolt = <1350000>; >> + regulator-name = "vdd_arm"; >> + regulator-state-mem { >> + regulator-off-in-suspend; >> + }; >> + }; >> + >> + vdd_gpu: DCDC_REG2 { >> + regulator-always-on; >> + regulator-boot-on; >> + regulator-min-microvolt = <850000>; >> + regulator-max-microvolt = <1250000>; >> + regulator-name = "vdd_gpu"; >> + regulator-state-mem { >> + regulator-on-in-suspend; >> + regulator-suspend-microvolt = <1000000>; >> + }; >> + }; >> + >> + vcc_ddr: DCDC_REG3 { >> + regulator-always-on; >> + regulator-boot-on; >> + regulator-name = "vcc_ddr"; >> + regulator-state-mem { >> + regulator-on-in-suspend; >> + }; >> + }; >> + >> + vcc_io: DCDC_REG4 { >> + regulator-always-on; >> + regulator-boot-on; >> + regulator-min-microvolt = <3300000>; >> + regulator-max-microvolt = <3300000>; >> + regulator-name = "vcc_io"; >> + regulator-state-mem { >> + regulator-on-in-suspend; >> + regulator-suspend-microvolt = <3300000>; >> + }; >> + }; >> + >> + vcc_lan: LDO_REG1 { >> + regulator-always-on; >> + regulator-boot-on; >> + regulator-min-microvolt = <3300000>; >> + regulator-max-microvolt = <3300000>; >> + regulator-name = "vcc_lan"; >> + regulator-state-mem { >> + regulator-on-in-suspend; >> + regulator-suspend-microvolt = <3300000>; >> + }; >> + }; >> + >> + vccio_sd: LDO_REG2 { >> + regulator-always-on; >> + regulator-boot-on; >> + regulator-min-microvolt = <3300000>; >> + regulator-max-microvolt = <3300000>; >> + regulator-name = "vccio_sd"; >> + regulator-state-mem { >> + regulator-off-in-suspend; >> + }; >> + }; >> + >> + vdd_10: LDO_REG3 { >> + regulator-always-on; >> + regulator-boot-on; >> + regulator-min-microvolt = <1000000>; >> + regulator-max-microvolt = <1000000>; >> + regulator-name = "vdd_10"; >> + regulator-state-mem { >> + regulator-on-in-suspend; >> + regulator-suspend-microvolt = <1000000>; >> + }; >> + }; >> + >> + vcc18_lcd: LDO_REG4 { >> + regulator-always-on; >> + regulator-boot-on; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + regulator-name = "vcc18_lcd"; >> + regulator-state-mem { >> + regulator-on-in-suspend; >> + regulator-suspend-microvolt = <1800000>; >> + }; >> + }; >> + >> + ldo5: LDO_REG5 { >> + regulator-always-on; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <3300000>; >> + regulator-name = "ldo5"; >> + }; >> + >> + vdd10_lcd: LDO_REG6 { >> + regulator-always-on; >> + regulator-boot-on; >> + regulator-min-microvolt = <1000000>; >> + regulator-max-microvolt = <1000000>; >> + regulator-name = "vdd10_lcd"; >> + regulator-state-mem { >> + regulator-on-in-suspend; >> + regulator-suspend-microvolt = <1000000>; >> + }; >> + }; >> + >> + vcc_18: LDO_REG7 { >> + regulator-always-on; >> + regulator-boot-on; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + regulator-name = "vcc_18"; >> + regulator-state-mem { >> + regulator-on-in-suspend; >> + regulator-suspend-microvolt = <1800000>; >> + }; >> + }; >> + >> + vcca_codec: LDO_REG8 { >> + regulator-always-on; >> + regulator-boot-on; >> + regulator-min-microvolt = <3300000>; >> + regulator-max-microvolt = <3300000>; >> + regulator-name = "vcca_codec"; >> + regulator-state-mem { >> + regulator-on-in-suspend; >> + regulator-suspend-microvolt = <3300000>; >> + }; >> + }; >> + >> + vcc_wl: SWITCH_REG1 { >> + regulator-always-on; >> + regulator-boot-on; >> + regulator-name = "vcc_wl"; >> + regulator-state-mem { >> + regulator-on-in-suspend; >> + }; >> + }; >> + >> + vcc_lcd: SWITCH_REG2 { >> + regulator-always-on; >> + regulator-boot-on; >> + regulator-name = "vcc_lcd"; >> + regulator-state-mem { >> + regulator-on-in-suspend; >> + }; >> + }; > only for my peace of mind, does the board wake again from suspend with these > rk808 settings? I.e. while I my rk3288-evb-rk808 wakes sucessfully, I haven't > been able to wake an act8846 based board (firefly) yet. I have not check suspend and wake up yet, I will test it and check with Chris Zhong later > >> + }; >> + }; >> +}; >> + >> +&i2c1 { >> + status = "okay"; >> + clock-frequency = <400000>; >> + >> + ak8963: ak8963@0d { >> + compatible = "asahi-kasei,ak8975"; >> + reg = <0x0d>; >> + interrupt-parent = <&gpio8>; >> + interrupts = <1 IRQ_TYPE_EDGE_RISING>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&comp_int>; >> + }; >> + >> + l3g4200d: l3g4200d@68 { >> + compatible = "st,l3g4200d-gyro"; >> + st,drdy-int-pin = <2>; >> + reg = <0x6b>; >> + }; >> + >> + mma8452: mma8452@1d { >> + compatible = "fsl,mma8452"; >> + reg = <0x1d>; >> + interrupt-parent = <&gpio8>; >> + interrupts = <0 IRQ_TYPE_EDGE_RISING>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&gsensor_int>; >> + }; >> +}; >> + >> +&i2c2 { >> + status = "okay"; >> +}; >> + >> +&i2c3 { >> + status = "okay"; >> +}; >> + >> +&i2c4 { >> + status = "okay"; >> +}; >> + >> +&i2c5 { >> + status = "okay"; >> +}; >> + >> +&pinctrl { >> + buttons { >> + pwrbtn: pwrbtn { >> + rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_up>; >> + }; > pwrbtn needs one indentation more. > > Also please sort alphabetically ... "ak8963" before "buttons" > OK, this will be fix in V2 >> + }; >> + >> + ak8963 { >> + comp_int: comp-int { >> + rockchip,pins = <8 1 RK_FUNC_GPIO &pcfg_pull_up>; >> + }; >> + }; >> + >> + ir { >> + ir_int: ir-int { >> + rockchip,pins = <0 6 RK_FUNC_GPIO &pcfg_pull_up>; >> + }; >> + }; >> + >> + mma8452 { >> + gsensor_int: gsensor-int { >> + rockchip,pins = <8 0 RK_FUNC_GPIO &pcfg_pull_up>; >> + }; >> + }; >> + >> + pmic { >> + pmic_int: pmic-int { >> + rockchip,pins = <RK_GPIO0 4 RK_FUNC_GPIO &pcfg_pull_up>; >> + }; >> + }; >> +}; >> + >> +&vopb { >> + status = "okay"; >> +}; >> + >> +&vopb_mmu { >> + status = "okay"; >> +}; >> + >> +&vopl { >> + status = "okay"; >> +}; >> + >> +&vopl_mmu { >> + status = "okay"; >> +}; >> + >> +&uart0 { >> + status = "okay"; >> +}; >> + >> +&uart1 { >> + status = "okay"; >> +}; >> + >> +&uart2 { >> + status = "okay"; >> +}; >> + >> +&uart3 { >> + status = "okay"; >> +}; >> + >> +&uart4 { >> + status = "okay"; >> +}; >> + >> +&usbphy { >> + status = "okay"; >> +}; > in general looks good. Because of the license issue I need you to submit a v2, > otherwise I could have fixed the small nitpicks myself. > Thanks very much for your review, I will fix all of them in V2 > Heiko > > > -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2015-03-01 7:27 UTC | newest]
Thread overview: 7+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2015-02-27 10:55 [PATCH 0/2] add dts for PopMetal board Andy Yan
2015-02-27 10:59 ` [PATCH 1/2] dt-bindings: add root compatible property " Andy Yan
2015-02-28 17:43 ` Heiko Stübner
2015-03-01 6:49 ` Andy Yan
[not found] ` <1425034505-25163-1-git-send-email-andy.yan-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
2015-02-27 11:03 ` [PATCH 2/2] ARM: dts: add rk3288 " Andy Yan
2015-02-28 17:57 ` Heiko Stübner
2015-03-01 7:27 ` Andy Yan
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).