* [PATCH v2 2/2] ARM: dts: add rk3288 PopMetal board
[not found] ` <1425201914-4695-1-git-send-email-andy.yan-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
@ 2015-03-01 9:32 ` Andy Yan
0 siblings, 0 replies; 5+ messages in thread
From: Andy Yan @ 2015-03-01 9:32 UTC (permalink / raw)
To: heiko-4mtYJXux2i+zQB+pC5nmwQ, devicetree-u79uwXL29TY76Z2rM5mHXA
Cc: naobsd-Re5JQEeQqe8AvxtiuMwx3w,
romain.perier-Re5JQEeQqe8AvxtiuMwx3w,
b.galvani-Re5JQEeQqe8AvxtiuMwx3w, galak-sgV2jX0FEOL9JmXXK+q4OQ,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
ijc+devicetree-KcIKpvwj1kUDXYZnReoRVg,
linux-rockchip-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A, pawel.moll-5wv7dgnIgG8,
mark.rutland-5wv7dgnIgG8, linux-lFZ/pmaqli7XmaaqVzeoHQ,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
mark.yao-TNX95d0MmH7DzftRWevZcw, Andy Yan
PopMetal is a rockchip rk3288 based board made by ChipSpark,
which has many interface such as VGA,HDMI,usb,ir,sdcad and lots of
sensors such as gyroscope(L3G4200D),accelerometer(mma8452),
compass(AK8963C).
This patch add a basic support for this board, which make the board
boot into a initramfs shell with sdcard,hdmi and all sensors enabled
Signed-off-by: Andy Yan <andy.yan-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
---
Changes in v2:
- use GPL + X11 dual license, adviced by Heiko
- indent pwrbtn
- move node "ak8963" before "buttons"
- add cpu0-supply
- add supply for rk808 regulator
arch/arm/boot/dts/rk3288-popmetal.dts | 447 ++++++++++++++++++++++++++++++++++
1 file changed, 447 insertions(+)
create mode 100644 arch/arm/boot/dts/rk3288-popmetal.dts
diff --git a/arch/arm/boot/dts/rk3288-popmetal.dts b/arch/arm/boot/dts/rk3288-popmetal.dts
new file mode 100644
index 0000000..d081f0e
--- /dev/null
+++ b/arch/arm/boot/dts/rk3288-popmetal.dts
@@ -0,0 +1,447 @@
+/*
+ * Copyright (c) 2014, 2015 Andy Yan <andy.yan-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "rk3288.dtsi"
+
+/ {
+ model = "PopMetal-RK3288";
+ compatible = "chipspark,popmetal-rk3288", "rockchip,rk3288";
+
+ memory{
+ reg = <0 0x80000000>;
+ };
+
+ ext_gmac: external-gmac-clock {
+ compatible = "fixed-clock";
+ clock-frequency = <125000000>;
+ clock-output-names = "ext_gmac";
+ #clock-cells = <0>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ autorepeat;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwrbtn>;
+
+ button@0 {
+ gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
+ linux,code = <116>;
+ label = "GPIO Key Power";
+ linux,input-type = <1>;
+ gpio-key,wakeup = <1>;
+ debounce-interval = <100>;
+ };
+ };
+
+ ir: ir-receiver {
+ compatible = "gpio-ir-receiver";
+ gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir_int>;
+ };
+
+ vcc_sys: vsys-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_sys";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+};
+
+&cpu0 {
+ cpu0-supply = <&vdd_cpu>;
+};
+
+&emmc {
+ broken-cd;
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ disable-wp;
+ non-removable;
+ num-slots = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_pwr &emmc_bus8>;
+ status = "okay";
+};
+
+&sdmmc {
+ bus-width = <4>;
+ cap-mmc-highspeed;
+ cap-sd-highspeed;
+ card-detect-delay = <200>;
+ disable-wp; /* wp not hooked up */
+ num-slots = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
+ status = "okay";
+};
+
+&gmac {
+ phy-supply = <&vcc_lan>;
+ phy-mode = "rgmii";
+ clock_in_out = "input";
+ snps,reset-gpio = <&gpio4 7 0>;
+ snps,reset-active-low;
+ snps,reset-delays-us = <0 10000 1000000>;
+ assigned-clocks = <&cru SCLK_MAC>;
+ assigned-clock-parents = <&ext_gmac>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii_pins>;
+ tx_delay = <0x30>;
+ rx_delay = <0x10>;
+ status = "ok";
+};
+
+&hdmi {
+ ddc-i2c-bus = <&i2c5>;
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ rk808: pmic@1b {
+ compatible = "rockchip,rk808";
+ reg = <0x1b>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int &global_pwroff>;
+ rockchip,system-power-controller;
+ wakeup-source;
+ #clock-cells = <1>;
+ clock-output-names = "xin32k", "rk808-clkout2";
+
+ vcc1-supply = <&vcc_sys>;
+ vcc2-supply = <&vcc_sys>;
+ vcc3-supply = <&vcc_sys>;
+ vcc4-supply = <&vcc_sys>;
+ vcc6-supply = <&vcc_sys>;
+ vcc7-supply = <&vcc_sys>;
+ vcc8-supply = <&vcc_18>;
+ vcc9-supply = <&vcc_io>;
+ vcc10-supply = <&vcc_io>;
+ vcc11-supply = <&vcc_sys>;
+ vcc12-supply = <&vcc_io>;
+ vddio-supply = <&vcc_io>;
+
+ regulators {
+ vdd_cpu: DCDC_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-name = "vdd_arm";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_gpu: DCDC_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1250000>;
+ regulator-name = "vdd_gpu";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vcc_ddr";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vcc_io: DCDC_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc_io";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcc_lan: LDO_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc_lan";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vccio_sd: LDO_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vccio_sd";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_10: LDO_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-name = "vdd_10";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+
+ vcc18_lcd: LDO_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc18_lcd";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ ldo5: LDO_REG5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "ldo5";
+ };
+
+ vdd10_lcd: LDO_REG6 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-name = "vdd10_lcd";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+
+ vcc_18: LDO_REG7 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc_18";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcca_codec: LDO_REG8 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcca_codec";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcc_wl: SWITCH_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vcc_wl";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vcc_lcd: SWITCH_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vcc_lcd";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+ };
+ };
+};
+
+&i2c1 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ ak8963: ak8963@0d {
+ compatible = "asahi-kasei,ak8975";
+ reg = <0x0d>;
+ interrupt-parent = <&gpio8>;
+ interrupts = <1 IRQ_TYPE_EDGE_RISING>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&comp_int>;
+ };
+
+ l3g4200d: l3g4200d@68 {
+ compatible = "st,l3g4200d-gyro";
+ st,drdy-int-pin = <2>;
+ reg = <0x6b>;
+ };
+
+ mma8452: mma8452@1d {
+ compatible = "fsl,mma8452";
+ reg = <0x1d>;
+ interrupt-parent = <&gpio8>;
+ interrupts = <0 IRQ_TYPE_EDGE_RISING>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&gsensor_int>;
+ };
+};
+
+&i2c2 {
+ status = "okay";
+};
+
+&i2c3 {
+ status = "okay";
+};
+
+&i2c4 {
+ status = "okay";
+};
+
+&i2c5 {
+ status = "okay";
+};
+
+&pinctrl {
+ ak8963 {
+ comp_int: comp-int {
+ rockchip,pins = <8 1 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ buttons {
+ pwrbtn: pwrbtn {
+ rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ ir {
+ ir_int: ir-int {
+ rockchip,pins = <0 6 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ mma8452 {
+ gsensor_int: gsensor-int {
+ rockchip,pins = <8 0 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ pmic {
+ pmic_int: pmic-int {
+ rockchip,pins = <RK_GPIO0 4 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+};
+
+&vopb {
+ status = "okay";
+};
+
+&vopb_mmu {
+ status = "okay";
+};
+
+&vopl {
+ status = "okay";
+};
+
+&vopl_mmu {
+ status = "okay";
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&uart3 {
+ status = "okay";
+};
+
+&uart4 {
+ status = "okay";
+};
+
+&usbphy {
+ status = "okay";
+};
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 5+ messages in thread