[PATCH v2 0/2] ARM: dts: add dts files for Cubieboard4

[PATCH v2 0/2] ARM: dts: add dts files for Cubieboard4

[tyler.baker-QSEj5FYQhm4dnm+yROfE0A]

From: Tyler Baker <tyler.baker-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>

This series adds basic support for the Cubietech Cubieboard4.

The Cubietech Cubieboard4 is a A80 based development board with 2GB DDR3, 8GB
eMMC, Micro SD, HDMI, VGA, 3.5mm audio jack. One USB OTG port and four USB 2.0
ports.

The sun9i-a80-optimus device tree[1] has been used to boot this board for some
time now, as the two platforms are very similar. But there are differences, so 
it deserves it's own device tree. I've tested this series on a 
Cubieboard4[2][3] and can confirm UART, eMMC, and MMC are working properly.

This patch series is based on arm-soc v4.0-rc2.

Changes v1 -> v2:
* Use more descriptive notation for stdout-path

Changes v0 -> v1:
* Corrected typo. a80-cubietruck -> a80-cubieboard4.
* Removed bootargs node.
* Added stdout-path for uart0.
* Removed unneeded newline.

[1] http://kernelci.org/boot/sun9i-a80-cubieboard4/ 
[2] http://lava.kernelci.org/scheduler/job/47969/log_file#L_13_308
[3] http://lava.kernelci.org/scheduler/job/47969/log_file#L_17_11

Tyler Baker (2):
  ARM: dts: add cubietech cubieboard4
  ARM: dts: add vendor prefix for cubietech

 .../devicetree/bindings/vendor-prefixes.txt        |   1 +
 arch/arm/boot/dts/Makefile                         |   3 +-
 arch/arm/boot/dts/sun9i-a80-cubieboard4.dts        | 100 +++++++++++++++++++++
 3 files changed, 103 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/boot/dts/sun9i-a80-cubieboard4.dts

-- 
2.1.0

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v2 1/2] ARM: dts: add cubietech cubieboard4

[tyler.baker-QSEj5FYQhm4dnm+yROfE0A]

From: Tyler Baker <tyler.baker-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>

Add a Cubietech Cubieboard4 device tree and instruct make to build it. This
device tree has been derived from the sun9i-a80-optimus.dts as they are very
similar in design[1]. Notably, I2C3 is not used on Cubieboard4 and the LED/PWM
definitions will need to be updated in the future.

[1] http://dl.cubieboard.org/model/cc-a80/Hardware/CC-A80-HW-V1.1.pdf

Signed-off-by: Tyler Baker <tyler.baker-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
---
 arch/arm/boot/dts/Makefile                  |  3 +-
 arch/arm/boot/dts/sun9i-a80-cubieboard4.dts | 99 +++++++++++++++++++++++++++++
 2 files changed, 101 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/boot/dts/sun9i-a80-cubieboard4.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 4837044..0f67dab 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -553,7 +553,8 @@ dtb-$(CONFIG_MACH_SUN8I) += \
 	sun8i-a23-ippo-q8h-v5.dtb \
 	sun8i-a23-ippo-q8h-v1.2.dtb
 dtb-$(CONFIG_MACH_SUN9I) += \
-	sun9i-a80-optimus.dtb
+	sun9i-a80-optimus.dtb \
+	sun9i-a80-cubieboard4.dtb
 dtb-$(CONFIG_ARCH_TEGRA_2x_SOC) += \
 	tegra20-harmony.dtb \
 	tegra20-iris-512.dtb \
diff --git a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
new file mode 100644
index 0000000..6484dcf
--- /dev/null
+++ b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
@@ -0,0 +1,99 @@
+/*
+ * Copyright 2015 Tyler Baker
+ *
+ * Tyler Baker <tyler.baker-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
+ * Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun9i-a80.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+	model = "Cubietech Cubieboard4";
+	compatible = "cubietech,a80-cubieboard4", "allwinner,sun9i-a80";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+};
+
+&pio {
+	mmc0_cd_pin_cubieboard4: mmc0_cd_pin@0 {
+		allwinner,pins = "PH18";
+		allwinner,function = "gpio_in";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+	};
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins>, <&mmc0_cd_pin_cubieboard4>;
+	vmmc-supply = <&reg_vcc3v0>;
+	bus-width = <4>;
+	cd-gpios = <&pio 7 18 GPIO_ACTIVE_HIGH>; /* PH18 */
+	cd-inverted;
+	status = "okay";
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_8bit_pins>;
+	vmmc-supply = <&reg_vcc3v0>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins_a>;
+	status = "okay";
+};
-- 
2.1.0

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v2 1/2] ARM: dts: add cubietech cubieboard4

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 784 bytes --]

On Mon, Mar 09, 2015 at 01:19:57PM -0700, tyler.baker-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org wrote:
> From: Tyler Baker <tyler.baker-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
> 
> Add a Cubietech Cubieboard4 device tree and instruct make to build it. This
> device tree has been derived from the sun9i-a80-optimus.dts as they are very
> similar in design[1]. Notably, I2C3 is not used on Cubieboard4 and the LED/PWM
> definitions will need to be updated in the future.
> 
> [1] http://dl.cubieboard.org/model/cc-a80/Hardware/CC-A80-HW-V1.1.pdf
> 
> Signed-off-by: Tyler Baker <tyler.baker-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>

Applied, thanks!

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

[PATCH v2 2/2] ARM: dts: add vendor prefix for cubietech

[tyler.baker-QSEj5FYQhm4dnm+yROfE0A]

From: Tyler Baker <tyler.baker-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>

Add a cubietech vendor prefix, as it is missing. The cubietruck, cubieboard2,
and cubieboard all already reference this prefix.

Signed-off-by: Tyler Baker <tyler.baker-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
---
 Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index aeb5bb5..58364cf 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -45,6 +45,7 @@ cnxt	Conexant Systems, Inc.
 cortina	Cortina Systems, Inc.
 cosmic	Cosmic Circuits
 crystalfontz	Crystalfontz America, Inc.
+cubietech	Cubietech, Ltd.
 dallas	Maxim Integrated Products (formerly Dallas Semiconductor)
 davicom	DAVICOM Semiconductor, Inc.
 denx	Denx Software Engineering
-- 
2.1.0

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html