* [PATCH v3 01/11] ARM: dts: Add labels to Exynos4 nodes
2015-04-17 13:47 [PATCH v3 00/11] ARM: dts: exynos4: labels for overriding nodes Krzysztof Kozlowski
@ 2015-04-17 13:47 ` Krzysztof Kozlowski
2015-04-17 13:47 ` [PATCH v3 02/11] ARM: dts: exynos4: Use labels for overriding nodes in Exynos4210 Krzysztof Kozlowski
` (9 subsequent siblings)
10 siblings, 0 replies; 12+ messages in thread
From: Krzysztof Kozlowski @ 2015-04-17 13:47 UTC (permalink / raw)
To: Kukjin Kim, devicetree, linux-arm-kernel, linux-samsung-soc,
linux-kernel
Cc: Arnd Bergmann, Olof Johansson, Krzysztof Kozlowski
Add new labels to certain nodes so they could be easily referenced by
Exynos4 board DTS files.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
---
arch/arm/boot/dts/exynos4.dtsi | 22 +++++++++++-----------
arch/arm/boot/dts/exynos4210-pinctrl.dtsi | 6 +++---
arch/arm/boot/dts/exynos4210.dtsi | 6 +++---
arch/arm/boot/dts/exynos4x12-pinctrl.dtsi | 8 ++++----
arch/arm/boot/dts/exynos4x12.dtsi | 2 +-
5 files changed, 22 insertions(+), 22 deletions(-)
diff --git a/arch/arm/boot/dts/exynos4.dtsi b/arch/arm/boot/dts/exynos4.dtsi
index e20cdc24c3bb..ef944e4f42d0 100644
--- a/arch/arm/boot/dts/exynos4.dtsi
+++ b/arch/arm/boot/dts/exynos4.dtsi
@@ -257,7 +257,7 @@
};
};
- watchdog@10060000 {
+ watchdog: watchdog@10060000 {
compatible = "samsung,s3c2410-wdt";
reg = <0x10060000 0x100>;
interrupts = <0 43 0>;
@@ -266,7 +266,7 @@
status = "disabled";
};
- rtc@10070000 {
+ rtc: rtc@10070000 {
compatible = "samsung,s3c6410-rtc";
reg = <0x10070000 0x100>;
interrupt-parent = <&pmu_system_controller>;
@@ -276,7 +276,7 @@
status = "disabled";
};
- keypad@100A0000 {
+ keypad: keypad@100A0000 {
compatible = "samsung,s5pv210-keypad";
reg = <0x100A0000 0x100>;
interrupts = <0 109 0>;
@@ -285,7 +285,7 @@
status = "disabled";
};
- sdhci@12510000 {
+ sdhci_0: sdhci@12510000 {
compatible = "samsung,exynos4210-sdhci";
reg = <0x12510000 0x100>;
interrupts = <0 73 0>;
@@ -294,7 +294,7 @@
status = "disabled";
};
- sdhci@12520000 {
+ sdhci_1: sdhci@12520000 {
compatible = "samsung,exynos4210-sdhci";
reg = <0x12520000 0x100>;
interrupts = <0 74 0>;
@@ -303,7 +303,7 @@
status = "disabled";
};
- sdhci@12530000 {
+ sdhci_2: sdhci@12530000 {
compatible = "samsung,exynos4210-sdhci";
reg = <0x12530000 0x100>;
interrupts = <0 75 0>;
@@ -312,7 +312,7 @@
status = "disabled";
};
- sdhci@12540000 {
+ sdhci_3: sdhci@12540000 {
compatible = "samsung,exynos4210-sdhci";
reg = <0x12540000 0x100>;
interrupts = <0 76 0>;
@@ -331,7 +331,7 @@
status = "disabled";
};
- hsotg@12480000 {
+ hsotg: hsotg@12480000 {
compatible = "samsung,s3c6400-hsotg";
reg = <0x12480000 0x20000>;
interrupts = <0 71 0>;
@@ -342,7 +342,7 @@
status = "disabled";
};
- ehci@12580000 {
+ ehci: ehci@12580000 {
compatible = "samsung,exynos4210-ehci";
reg = <0x12580000 0x100>;
interrupts = <0 70 0>;
@@ -368,7 +368,7 @@
};
};
- ohci@12590000 {
+ ohci: ohci@12590000 {
compatible = "samsung,exynos4210-ohci";
reg = <0x12590000 0x100>;
interrupts = <0 70 0>;
@@ -621,7 +621,7 @@
status = "disabled";
};
- pwm@139D0000 {
+ pwm: pwm@139D0000 {
compatible = "samsung,exynos4210-pwm";
reg = <0x139D0000 0x1000>;
interrupts = <0 37 0>, <0 38 0>, <0 39 0>, <0 40 0>, <0 41 0>;
diff --git a/arch/arm/boot/dts/exynos4210-pinctrl.dtsi b/arch/arm/boot/dts/exynos4210-pinctrl.dtsi
index a7c212891674..4704e7bb2628 100644
--- a/arch/arm/boot/dts/exynos4210-pinctrl.dtsi
+++ b/arch/arm/boot/dts/exynos4210-pinctrl.dtsi
@@ -15,7 +15,7 @@
*/
/ {
- pinctrl@11400000 {
+ pinctrl_0: pinctrl@11400000 {
gpa0: gpa0 {
gpio-controller;
#gpio-cells = <2>;
@@ -421,7 +421,7 @@
};
};
- pinctrl@11000000 {
+ pinctrl_1: pinctrl@11000000 {
gpj0: gpj0 {
gpio-controller;
#gpio-cells = <2>;
@@ -822,7 +822,7 @@
};
};
- pinctrl@03860000 {
+ pinctrl_3: pinctrl@03860000 {
gpz: gpz {
gpio-controller;
#gpio-cells = <2>;
diff --git a/arch/arm/boot/dts/exynos4210.dtsi b/arch/arm/boot/dts/exynos4210.dtsi
index be89f83f70e7..76b84852f29c 100644
--- a/arch/arm/boot/dts/exynos4210.dtsi
+++ b/arch/arm/boot/dts/exynos4210.dtsi
@@ -62,7 +62,7 @@
#clock-cells = <1>;
};
- sysram@02020000 {
+ sysram: sysram@02020000 {
compatible = "mmio-sram";
reg = <0x02020000 0x20000>;
#address-cells = <1>;
@@ -107,7 +107,7 @@
<0 12 0>, <0 13 0>, <0 14 0>, <0 15 0>;
};
- mct@10050000 {
+ mct: mct@10050000 {
compatible = "samsung,exynos4210-mct";
reg = <0x10050000 0x800>;
interrupt-parent = <&mct_map>;
@@ -189,7 +189,7 @@
};
};
- g2d@12800000 {
+ g2d: g2d@12800000 {
compatible = "samsung,s5pv210-g2d";
reg = <0x12800000 0x1000>;
interrupts = <0 89 0>;
diff --git a/arch/arm/boot/dts/exynos4x12-pinctrl.dtsi b/arch/arm/boot/dts/exynos4x12-pinctrl.dtsi
index c141931378e7..bac25c672789 100644
--- a/arch/arm/boot/dts/exynos4x12-pinctrl.dtsi
+++ b/arch/arm/boot/dts/exynos4x12-pinctrl.dtsi
@@ -29,7 +29,7 @@
}
/ {
- pinctrl@11400000 {
+ pinctrl_0: pinctrl@11400000 {
gpa0: gpa0 {
gpio-controller;
#gpio-cells = <2>;
@@ -441,7 +441,7 @@
};
};
- pinctrl@11000000 {
+ pinctrl_1: pinctrl@11000000 {
gpk0: gpk0 {
gpio-controller;
#gpio-cells = <2>;
@@ -887,7 +887,7 @@
};
};
- pinctrl@03860000 {
+ pinctrl_2: pinctrl@03860000 {
gpz: gpz {
gpio-controller;
#gpio-cells = <2>;
@@ -913,7 +913,7 @@
};
};
- pinctrl@106E0000 {
+ pinctrl_3: pinctrl@106E0000 {
gpv0: gpv0 {
gpio-controller;
#gpio-cells = <2>;
diff --git a/arch/arm/boot/dts/exynos4x12.dtsi b/arch/arm/boot/dts/exynos4x12.dtsi
index 6a6abe14fd9b..657b5ca39ce8 100644
--- a/arch/arm/boot/dts/exynos4x12.dtsi
+++ b/arch/arm/boot/dts/exynos4x12.dtsi
@@ -159,7 +159,7 @@
#clock-cells = <1>;
};
- g2d@10800000 {
+ g2d: g2d@10800000 {
compatible = "samsung,exynos4212-g2d";
reg = <0x10800000 0x1000>;
interrupts = <0 89 0>;
--
2.1.0
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v3 02/11] ARM: dts: exynos4: Use labels for overriding nodes in Exynos4210
2015-04-17 13:47 [PATCH v3 00/11] ARM: dts: exynos4: labels for overriding nodes Krzysztof Kozlowski
2015-04-17 13:47 ` [PATCH v3 01/11] ARM: dts: Add labels to Exynos4 nodes Krzysztof Kozlowski
@ 2015-04-17 13:47 ` Krzysztof Kozlowski
2015-04-17 13:47 ` [PATCH v3 03/11] ARM: dts: exynos4: Use labels for overriding nodes in Exynos4210 Origen Krzysztof Kozlowski
` (8 subsequent siblings)
10 siblings, 0 replies; 12+ messages in thread
From: Krzysztof Kozlowski @ 2015-04-17 13:47 UTC (permalink / raw)
To: Kukjin Kim, devicetree, linux-arm-kernel, linux-samsung-soc,
linux-kernel
Cc: Olof Johansson, Krzysztof Kozlowski, Arnd Bergmann
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
---
arch/arm/boot/dts/exynos4210.dtsi | 43 +++++++++++++++++++--------------------
1 file changed, 21 insertions(+), 22 deletions(-)
diff --git a/arch/arm/boot/dts/exynos4210.dtsi b/arch/arm/boot/dts/exynos4210.dtsi
index 76b84852f29c..a9a55304e31a 100644
--- a/arch/arm/boot/dts/exynos4210.dtsi
+++ b/arch/arm/boot/dts/exynos4210.dtsi
@@ -52,16 +52,6 @@
};
};
- pmu_system_controller: system-controller@10020000 {
- clock-names = "clkout0", "clkout1", "clkout2", "clkout3",
- "clkout4", "clkout8", "clkout9";
- clocks = <&clock CLK_OUT_DMC>, <&clock CLK_OUT_TOP>,
- <&clock CLK_OUT_LEFTBUS>, <&clock CLK_OUT_RIGHTBUS>,
- <&clock CLK_OUT_CPU>, <&clock CLK_XXTI>,
- <&clock CLK_XUSBXTI>;
- #clock-cells = <1>;
- };
-
sysram: sysram@02020000 {
compatible = "mmio-sram";
reg = <0x02020000 0x20000>;
@@ -95,18 +85,6 @@
arm,data-latency = <2 2 1>;
};
- gic: interrupt-controller@10490000 {
- cpu-offset = <0x8000>;
- };
-
- combiner: interrupt-controller@10440000 {
- samsung,combiner-nr = <16>;
- interrupts = <0 0 0>, <0 1 0>, <0 2 0>, <0 3 0>,
- <0 4 0>, <0 5 0>, <0 6 0>, <0 7 0>,
- <0 8 0>, <0 9 0>, <0 10 0>, <0 11 0>,
- <0 12 0>, <0 13 0>, <0 14 0>, <0 15 0>;
- };
-
mct: mct@10050000 {
compatible = "samsung,exynos4210-mct";
reg = <0x10050000 0x800>;
@@ -245,3 +223,24 @@
status = "disabled";
};
};
+
+&gic {
+ cpu-offset = <0x8000>;
+};
+
+&combiner {
+ samsung,combiner-nr = <16>;
+ interrupts = <0 0 0>, <0 1 0>, <0 2 0>, <0 3 0>,
+ <0 4 0>, <0 5 0>, <0 6 0>, <0 7 0>,
+ <0 8 0>, <0 9 0>, <0 10 0>, <0 11 0>,
+ <0 12 0>, <0 13 0>, <0 14 0>, <0 15 0>;
+};
+
+&pmu_system_controller {
+ clock-names = "clkout0", "clkout1", "clkout2", "clkout3",
+ "clkout4", "clkout8", "clkout9";
+ clocks = <&clock CLK_OUT_DMC>, <&clock CLK_OUT_TOP>,
+ <&clock CLK_OUT_LEFTBUS>, <&clock CLK_OUT_RIGHTBUS>,
+ <&clock CLK_OUT_CPU>, <&clock CLK_XXTI>, <&clock CLK_XUSBXTI>;
+ #clock-cells = <1>;
+};
--
2.1.0
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v3 03/11] ARM: dts: exynos4: Use labels for overriding nodes in Exynos4210 Origen
2015-04-17 13:47 [PATCH v3 00/11] ARM: dts: exynos4: labels for overriding nodes Krzysztof Kozlowski
2015-04-17 13:47 ` [PATCH v3 01/11] ARM: dts: Add labels to Exynos4 nodes Krzysztof Kozlowski
2015-04-17 13:47 ` [PATCH v3 02/11] ARM: dts: exynos4: Use labels for overriding nodes in Exynos4210 Krzysztof Kozlowski
@ 2015-04-17 13:47 ` Krzysztof Kozlowski
2015-04-17 13:47 ` [PATCH v3 04/11] ARM: dts: exynos4: Use labels for overriding nodes in SMDKv310 Krzysztof Kozlowski
` (7 subsequent siblings)
10 siblings, 0 replies; 12+ messages in thread
From: Krzysztof Kozlowski @ 2015-04-17 13:47 UTC (permalink / raw)
To: Kukjin Kim, devicetree, linux-arm-kernel, linux-samsung-soc,
linux-kernel
Cc: Arnd Bergmann, Olof Johansson, Krzysztof Kozlowski
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
---
arch/arm/boot/dts/exynos4210-origen.dts | 418 ++++++++++++++++----------------
1 file changed, 209 insertions(+), 209 deletions(-)
diff --git a/arch/arm/boot/dts/exynos4210-origen.dts b/arch/arm/boot/dts/exynos4210-origen.dts
index b81146141402..e0abfc3324d1 100644
--- a/arch/arm/boot/dts/exynos4210-origen.dts
+++ b/arch/arm/boot/dts/exynos4210-origen.dts
@@ -50,209 +50,6 @@
};
};
- watchdog@10060000 {
- status = "okay";
- };
-
- rtc@10070000 {
- status = "okay";
- };
-
- tmu@100C0000 {
- status = "okay";
- };
-
- sdhci@12530000 {
- bus-width = <4>;
- pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &sd2_cd>;
- pinctrl-names = "default";
- vmmc-supply = <&mmc_reg>;
- status = "okay";
- };
-
- sdhci@12510000 {
- bus-width = <4>;
- pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_cd>;
- pinctrl-names = "default";
- vmmc-supply = <&mmc_reg>;
- status = "okay";
- };
-
- g2d@12800000 {
- status = "okay";
- };
-
- codec@13400000 {
- samsung,mfc-r = <0x43000000 0x800000>;
- samsung,mfc-l = <0x51000000 0x800000>;
- status = "okay";
- };
-
- serial@13800000 {
- status = "okay";
- };
-
- serial@13810000 {
- status = "okay";
- };
-
- serial@13820000 {
- status = "okay";
- };
-
- serial@13830000 {
- status = "okay";
- };
-
- i2c@13860000 {
- status = "okay";
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-max-bus-freq = <20000>;
- pinctrl-0 = <&i2c0_bus>;
- pinctrl-names = "default";
-
- max8997_pmic@66 {
- compatible = "maxim,max8997-pmic";
- reg = <0x66>;
- interrupt-parent = <&gpx0>;
- interrupts = <4 0>, <3 0>;
-
- max8997,pmic-buck1-dvs-voltage = <1350000>;
- max8997,pmic-buck2-dvs-voltage = <1100000>;
- max8997,pmic-buck5-dvs-voltage = <1200000>;
-
- regulators {
- ldo1_reg: LDO1 {
- regulator-name = "VDD_ABB_3.3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- ldo2_reg: LDO2 {
- regulator-name = "VDD_ALIVE_1.1V";
- regulator-min-microvolt = <1100000>;
- regulator-max-microvolt = <1100000>;
- regulator-always-on;
- };
-
- ldo3_reg: LDO3 {
- regulator-name = "VMIPI_1.1V";
- regulator-min-microvolt = <1100000>;
- regulator-max-microvolt = <1100000>;
- };
-
- ldo4_reg: LDO4 {
- regulator-name = "VDD_RTC_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- ldo6_reg: LDO6 {
- regulator-name = "VMIPI_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- ldo7_reg: LDO7 {
- regulator-name = "VDD_AUD_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo8_reg: LDO8 {
- regulator-name = "VADC_3.3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- ldo9_reg: LDO9 {
- regulator-name = "DVDD_SWB_2.8V";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- regulator-always-on;
- };
-
- ldo10_reg: LDO10 {
- regulator-name = "VDD_PLL_1.1V";
- regulator-min-microvolt = <1100000>;
- regulator-max-microvolt = <1100000>;
- regulator-always-on;
- };
-
- ldo11_reg: LDO11 {
- regulator-name = "VDD_AUD_3V";
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- };
-
- ldo14_reg: LDO14 {
- regulator-name = "AVDD18_SWB_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- ldo17_reg: LDO17 {
- regulator-name = "VDD_SWB_3.3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
-
- ldo21_reg: LDO21 {
- regulator-name = "VDD_MIF_1.2V";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-always-on;
- };
-
- buck1_reg: BUCK1 {
- /*
- * HACK: The real name is VDD_ARM_1.2V,
- * but exynos-cpufreq does not support
- * DT-based regulator lookup yet.
- */
- regulator-name = "vdd_arm";
- regulator-min-microvolt = <950000>;
- regulator-max-microvolt = <1350000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- buck2_reg: BUCK2 {
- regulator-name = "VDD_INT_1.1V";
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1100000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- buck3_reg: BUCK3 {
- regulator-name = "VDD_G3D_1.1V";
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1100000>;
- };
-
- buck5_reg: BUCK5 {
- regulator-name = "VDDQ_M1M2_1.2V";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-always-on;
- };
-
- buck7_reg: BUCK7 {
- regulator-name = "VDD_LCD_3.3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-boot-on;
- regulator-always-on;
- };
- };
- };
- };
-
gpio_keys {
compatible = "gpio-keys";
#address-cells = <1>;
@@ -314,12 +111,6 @@
};
};
- fimd@11c00000 {
- pinctrl-0 = <&lcd_en &lcd_clk &lcd_data24 &pwm0_out>;
- pinctrl-names = "default";
- status = "okay";
- };
-
display-timings {
native-mode = <&timing0>;
timing0: timing {
@@ -335,3 +126,212 @@
};
};
};
+
+&fimd {
+ pinctrl-0 = <&lcd_en &lcd_clk &lcd_data24 &pwm0_out>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&g2d {
+ status = "okay";
+};
+
+&i2c_0 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <20000>;
+ pinctrl-0 = <&i2c0_bus>;
+ pinctrl-names = "default";
+
+ max8997_pmic@66 {
+ compatible = "maxim,max8997-pmic";
+ reg = <0x66>;
+ interrupt-parent = <&gpx0>;
+ interrupts = <4 0>, <3 0>;
+
+ max8997,pmic-buck1-dvs-voltage = <1350000>;
+ max8997,pmic-buck2-dvs-voltage = <1100000>;
+ max8997,pmic-buck5-dvs-voltage = <1200000>;
+
+ regulators {
+ ldo1_reg: LDO1 {
+ regulator-name = "VDD_ABB_3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldo2_reg: LDO2 {
+ regulator-name = "VDD_ALIVE_1.1V";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ };
+
+ ldo3_reg: LDO3 {
+ regulator-name = "VMIPI_1.1V";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ };
+
+ ldo4_reg: LDO4 {
+ regulator-name = "VDD_RTC_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo6_reg: LDO6 {
+ regulator-name = "VMIPI_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo7_reg: LDO7 {
+ regulator-name = "VDD_AUD_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo8_reg: LDO8 {
+ regulator-name = "VADC_3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldo9_reg: LDO9 {
+ regulator-name = "DVDD_SWB_2.8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ };
+
+ ldo10_reg: LDO10 {
+ regulator-name = "VDD_PLL_1.1V";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ };
+
+ ldo11_reg: LDO11 {
+ regulator-name = "VDD_AUD_3V";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ ldo14_reg: LDO14 {
+ regulator-name = "AVDD18_SWB_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo17_reg: LDO17 {
+ regulator-name = "VDD_SWB_3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ ldo21_reg: LDO21 {
+ regulator-name = "VDD_MIF_1.2V";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ };
+
+ buck1_reg: BUCK1 {
+ /*
+ * HACK: The real name is VDD_ARM_1.2V,
+ * but exynos-cpufreq does not support
+ * DT-based regulator lookup yet.
+ */
+ regulator-name = "vdd_arm";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buck2_reg: BUCK2 {
+ regulator-name = "VDD_INT_1.1V";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buck3_reg: BUCK3 {
+ regulator-name = "VDD_G3D_1.1V";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1100000>;
+ };
+
+ buck5_reg: BUCK5 {
+ regulator-name = "VDDQ_M1M2_1.2V";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ };
+
+ buck7_reg: BUCK7 {
+ regulator-name = "VDD_LCD_3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
+};
+
+&mfc {
+ samsung,mfc-r = <0x43000000 0x800000>;
+ samsung,mfc-l = <0x51000000 0x800000>;
+ status = "okay";
+};
+
+&sdhci_0 {
+ bus-width = <4>;
+ pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_cd>;
+ pinctrl-names = "default";
+ vmmc-supply = <&mmc_reg>;
+ status = "okay";
+};
+
+&sdhci_2 {
+ bus-width = <4>;
+ pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &sd2_cd>;
+ pinctrl-names = "default";
+ vmmc-supply = <&mmc_reg>;
+ status = "okay";
+};
+
+&serial_0 {
+ status = "okay";
+};
+
+&serial_1 {
+ status = "okay";
+};
+
+&serial_2 {
+ status = "okay";
+};
+
+&serial_3 {
+ status = "okay";
+};
+
+&rtc {
+ status = "okay";
+};
+
+&tmu {
+ status = "okay";
+};
+
+&watchdog {
+ status = "okay";
+};
--
2.1.0
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v3 04/11] ARM: dts: exynos4: Use labels for overriding nodes in SMDKv310
2015-04-17 13:47 [PATCH v3 00/11] ARM: dts: exynos4: labels for overriding nodes Krzysztof Kozlowski
` (2 preceding siblings ...)
2015-04-17 13:47 ` [PATCH v3 03/11] ARM: dts: exynos4: Use labels for overriding nodes in Exynos4210 Origen Krzysztof Kozlowski
@ 2015-04-17 13:47 ` Krzysztof Kozlowski
2015-04-17 13:47 ` [PATCH v3 05/11] ARM: dts: exynos4: Use labels for overriding nodes in Trats Krzysztof Kozlowski
` (6 subsequent siblings)
10 siblings, 0 replies; 12+ messages in thread
From: Krzysztof Kozlowski @ 2015-04-17 13:47 UTC (permalink / raw)
To: Kukjin Kim, devicetree, linux-arm-kernel, linux-samsung-soc,
linux-kernel
Cc: Olof Johansson, Krzysztof Kozlowski, Arnd Bergmann
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
---
arch/arm/boot/dts/exynos4210-smdkv310.dts | 280 +++++++++++++++---------------
1 file changed, 140 insertions(+), 140 deletions(-)
diff --git a/arch/arm/boot/dts/exynos4210-smdkv310.dts b/arch/arm/boot/dts/exynos4210-smdkv310.dts
index 86216fff1b4f..043b03caff8f 100644
--- a/arch/arm/boot/dts/exynos4210-smdkv310.dts
+++ b/arch/arm/boot/dts/exynos4210-smdkv310.dts
@@ -30,181 +30,181 @@
stdout-path = &serial_1;
};
- sdhci@12530000 {
- bus-width = <4>;
- pinctrl-names = "default";
- pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
- status = "okay";
- };
+ fixed-rate-clocks {
+ xxti {
+ compatible = "samsung,clock-xxti";
+ clock-frequency = <12000000>;
+ };
- g2d@12800000 {
- status = "okay";
+ xusbxti {
+ compatible = "samsung,clock-xusbxti";
+ clock-frequency = <24000000>;
+ };
};
+};
- codec@13400000 {
- samsung,mfc-r = <0x43000000 0x800000>;
- samsung,mfc-l = <0x51000000 0x800000>;
- status = "okay";
- };
+&g2d {
+ status = "okay";
+};
- serial@13800000 {
- status = "okay";
- };
+&i2c_0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <100000>;
+ status = "okay";
- serial@13810000 {
- status = "okay";
+ eeprom@50 {
+ compatible = "samsung,24ad0xd1";
+ reg = <0x50>;
};
- serial@13820000 {
- status = "okay";
+ eeprom@52 {
+ compatible = "samsung,24ad0xd1";
+ reg = <0x52>;
};
+};
- serial@13830000 {
- status = "okay";
+&keypad {
+ samsung,keypad-num-rows = <2>;
+ samsung,keypad-num-columns = <8>;
+ linux,keypad-no-autorepeat;
+ linux,keypad-wakeup;
+ pinctrl-names = "default";
+ pinctrl-0 = <&keypad_rows &keypad_cols>;
+ status = "okay";
+
+ key_1 {
+ keypad,row = <0>;
+ keypad,column = <3>;
+ linux,code = <2>;
};
- pinctrl@11000000 {
- keypad_rows: keypad-rows {
- samsung,pins = "gpx2-0", "gpx2-1";
- samsung,pin-function = <3>;
- samsung,pin-pud = <3>;
- samsung,pin-drv = <0>;
- };
-
- keypad_cols: keypad-cols {
- samsung,pins = "gpx1-0", "gpx1-1", "gpx1-2", "gpx1-3",
- "gpx1-4", "gpx1-5", "gpx1-6", "gpx1-7";
- samsung,pin-function = <3>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <0>;
- };
+ key_2 {
+ keypad,row = <0>;
+ keypad,column = <4>;
+ linux,code = <3>;
};
- keypad@100A0000 {
- samsung,keypad-num-rows = <2>;
- samsung,keypad-num-columns = <8>;
- linux,keypad-no-autorepeat;
- linux,keypad-wakeup;
- pinctrl-names = "default";
- pinctrl-0 = <&keypad_rows &keypad_cols>;
- status = "okay";
+ key_3 {
+ keypad,row = <0>;
+ keypad,column = <5>;
+ linux,code = <4>;
+ };
- key_1 {
- keypad,row = <0>;
- keypad,column = <3>;
- linux,code = <2>;
- };
+ key_4 {
+ keypad,row = <0>;
+ keypad,column = <6>;
+ linux,code = <5>;
+ };
- key_2 {
- keypad,row = <0>;
- keypad,column = <4>;
- linux,code = <3>;
- };
+ key_5 {
+ keypad,row = <0>;
+ keypad,column = <7>;
+ linux,code = <6>;
+ };
- key_3 {
- keypad,row = <0>;
- keypad,column = <5>;
- linux,code = <4>;
- };
+ key_a {
+ keypad,row = <1>;
+ keypad,column = <3>;
+ linux,code = <30>;
+ };
- key_4 {
- keypad,row = <0>;
- keypad,column = <6>;
- linux,code = <5>;
- };
+ key_b {
+ keypad,row = <1>;
+ keypad,column = <4>;
+ linux,code = <48>;
+ };
- key_5 {
- keypad,row = <0>;
- keypad,column = <7>;
- linux,code = <6>;
- };
+ key_c {
+ keypad,row = <1>;
+ keypad,column = <5>;
+ linux,code = <46>;
+ };
- key_a {
- keypad,row = <1>;
- keypad,column = <3>;
- linux,code = <30>;
- };
+ key_d {
+ keypad,row = <1>;
+ keypad,column = <6>;
+ linux,code = <32>;
+ };
- key_b {
- keypad,row = <1>;
- keypad,column = <4>;
- linux,code = <48>;
- };
+ key_e {
+ keypad,row = <1>;
+ keypad,column = <7>;
+ linux,code = <18>;
+ };
+};
- key_c {
- keypad,row = <1>;
- keypad,column = <5>;
- linux,code = <46>;
- };
+&mfc {
+ samsung,mfc-r = <0x43000000 0x800000>;
+ samsung,mfc-l = <0x51000000 0x800000>;
+ status = "okay";
+};
- key_d {
- keypad,row = <1>;
- keypad,column = <6>;
- linux,code = <32>;
- };
+&pinctrl_1 {
+ keypad_rows: keypad-rows {
+ samsung,pins = "gpx2-0", "gpx2-1";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
- key_e {
- keypad,row = <1>;
- keypad,column = <7>;
- linux,code = <18>;
- };
+ keypad_cols: keypad-cols {
+ samsung,pins = "gpx1-0", "gpx1-1", "gpx1-2", "gpx1-3",
+ "gpx1-4", "gpx1-5", "gpx1-6", "gpx1-7";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
};
+};
- i2c@13860000 {
- #address-cells = <1>;
- #size-cells = <0>;
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-max-bus-freq = <100000>;
- status = "okay";
-
- eeprom@50 {
- compatible = "samsung,24ad0xd1";
- reg = <0x50>;
- };
+&sdhci_2 {
+ bus-width = <4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
+ status = "okay";
+};
- eeprom@52 {
- compatible = "samsung,24ad0xd1";
- reg = <0x52>;
- };
- };
+&serial_0 {
+ status = "okay";
+};
- spi_2: spi@13940000 {
- cs-gpios = <&gpc1 2 0>;
- status = "okay";
+&serial_1 {
+ status = "okay";
+};
- w25x80@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "w25x80";
- reg = <0>;
- spi-max-frequency = <1000000>;
+&serial_2 {
+ status = "okay";
+};
- controller-data {
- samsung,spi-feedback-delay = <0>;
- };
+&serial_3 {
+ status = "okay";
+};
- partition@0 {
- label = "U-Boot";
- reg = <0x0 0x40000>;
- read-only;
- };
+&spi_2 {
+ cs-gpios = <&gpc1 2 0>;
+ status = "okay";
- partition@40000 {
- label = "Kernel";
- reg = <0x40000 0xc0000>;
- };
+ w25x80@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "w25x80";
+ reg = <0>;
+ spi-max-frequency = <1000000>;
+
+ controller-data {
+ samsung,spi-feedback-delay = <0>;
};
- };
- fixed-rate-clocks {
- xxti {
- compatible = "samsung,clock-xxti";
- clock-frequency = <12000000>;
+ partition@0 {
+ label = "U-Boot";
+ reg = <0x0 0x40000>;
+ read-only;
};
- xusbxti {
- compatible = "samsung,clock-xusbxti";
- clock-frequency = <24000000>;
+ partition@40000 {
+ label = "Kernel";
+ reg = <0x40000 0xc0000>;
};
};
};
--
2.1.0
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v3 05/11] ARM: dts: exynos4: Use labels for overriding nodes in Trats
2015-04-17 13:47 [PATCH v3 00/11] ARM: dts: exynos4: labels for overriding nodes Krzysztof Kozlowski
` (3 preceding siblings ...)
2015-04-17 13:47 ` [PATCH v3 04/11] ARM: dts: exynos4: Use labels for overriding nodes in SMDKv310 Krzysztof Kozlowski
@ 2015-04-17 13:47 ` Krzysztof Kozlowski
2015-04-17 13:47 ` [PATCH v3 06/11] ARM: dts: exynos4: Use labels for overriding nodes in Exynos4212 Krzysztof Kozlowski
` (5 subsequent siblings)
10 siblings, 0 replies; 12+ messages in thread
From: Krzysztof Kozlowski @ 2015-04-17 13:47 UTC (permalink / raw)
To: Kukjin Kim, devicetree, linux-arm-kernel, linux-samsung-soc,
linux-kernel
Cc: Arnd Bergmann, Olof Johansson, Krzysztof Kozlowski
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
---
arch/arm/boot/dts/exynos4210-trats.dts | 592 ++++++++++++++++-----------------
1 file changed, 296 insertions(+), 296 deletions(-)
diff --git a/arch/arm/boot/dts/exynos4210-trats.dts b/arch/arm/boot/dts/exynos4210-trats.dts
index 32c5fd8f6269..98f3ce65cb9a 100644
--- a/arch/arm/boot/dts/exynos4210-trats.dts
+++ b/arch/arm/boot/dts/exynos4210-trats.dts
@@ -89,42 +89,6 @@
};
};
- hsotg@12480000 {
- vusb_d-supply = <&vusb_reg>;
- vusb_a-supply = <&vusbdac_reg>;
- dr_mode = "peripheral";
- status = "okay";
- };
-
- sdhci_emmc: sdhci@12510000 {
- bus-width = <8>;
- non-removable;
- pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus8>;
- pinctrl-names = "default";
- vmmc-supply = <&vemmc_reg>;
- status = "okay";
- };
-
- exynos-usbphy@125B0000 {
- status = "okay";
- };
-
- serial@13800000 {
- status = "okay";
- };
-
- serial@13810000 {
- status = "okay";
- };
-
- serial@13820000 {
- status = "okay";
- };
-
- serial@13830000 {
- status = "okay";
- };
-
gpio-keys {
compatible = "gpio-keys";
@@ -158,201 +122,6 @@
};
};
- i2c@13890000 {
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-slave-addr = <0x10>;
- samsung,i2c-max-bus-freq = <400000>;
- pinctrl-0 = <&i2c3_bus>;
- pinctrl-names = "default";
- status = "okay";
-
- mms114-touchscreen@48 {
- compatible = "melfas,mms114";
- reg = <0x48>;
- interrupt-parent = <&gpx0>;
- interrupts = <4 2>;
- x-size = <720>;
- y-size = <1280>;
- avdd-supply = <&tsp_reg>;
- vdd-supply = <&tsp_reg>;
- };
- };
-
- i2c@138B0000 {
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-slave-addr = <0x10>;
- samsung,i2c-max-bus-freq = <100000>;
- pinctrl-0 = <&i2c5_bus>;
- pinctrl-names = "default";
- status = "okay";
-
- max8997_pmic@66 {
- compatible = "maxim,max8997-pmic";
-
- reg = <0x66>;
-
- max8997,pmic-buck1-uses-gpio-dvs;
- max8997,pmic-buck2-uses-gpio-dvs;
- max8997,pmic-buck5-uses-gpio-dvs;
-
- max8997,pmic-ignore-gpiodvs-side-effect;
- max8997,pmic-buck125-default-dvs-idx = <0>;
-
- max8997,pmic-buck125-dvs-gpios = <&gpx0 5 0>,
- <&gpx0 6 0>,
- <&gpl0 0 0>;
-
- max8997,pmic-buck1-dvs-voltage = <1350000>, <1300000>,
- <1250000>, <1200000>,
- <1150000>, <1100000>,
- <1000000>, <950000>;
-
- max8997,pmic-buck2-dvs-voltage = <1100000>, <1000000>,
- <950000>, <900000>,
- <1100000>, <1000000>,
- <950000>, <900000>;
-
- max8997,pmic-buck5-dvs-voltage = <1200000>, <1200000>,
- <1200000>, <1200000>,
- <1200000>, <1200000>,
- <1200000>, <1200000>;
-
- regulators {
- valive_reg: LDO2 {
- regulator-name = "VALIVE_1.1V_C210";
- regulator-min-microvolt = <1100000>;
- regulator-max-microvolt = <1100000>;
- regulator-always-on;
- };
-
- vusb_reg: LDO3 {
- regulator-name = "VUSB_1.1V_C210";
- regulator-min-microvolt = <1100000>;
- regulator-max-microvolt = <1100000>;
- };
-
- vmipi_reg: LDO4 {
- regulator-name = "VMIPI_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- vpda_reg: LDO6 {
- regulator-name = "VCC_1.8V_PDA";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- vcam_reg: LDO7 {
- regulator-name = "CAM_ISP_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- vusbdac_reg: LDO8 {
- regulator-name = "VUSB/VDAC_3.3V_C210";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- vccpda_reg: LDO9 {
- regulator-name = "VCC_2.8V_PDA";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- regulator-always-on;
- };
-
- vpll_reg: LDO10 {
- regulator-name = "VPLL_1.1V_C210";
- regulator-min-microvolt = <1100000>;
- regulator-max-microvolt = <1100000>;
- regulator-always-on;
- };
-
- vtcam_reg: LDO12 {
- regulator-name = "VT_CAM_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- vcclcd_reg: LDO13 {
- regulator-name = "VCC_3.3V_LCD";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- vlcd_reg: LDO15 {
- regulator-name = "VLCD_2.2V";
- regulator-min-microvolt = <2200000>;
- regulator-max-microvolt = <2200000>;
- };
-
- camsensor_reg: LDO16 {
- regulator-name = "CAM_SENSOR_IO_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- vddq_reg: LDO21 {
- regulator-name = "VDDQ_M1M2_1.2V";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-always-on;
- };
-
- varm_breg: BUCK1 {
- /*
- * HACK: The real name is VARM_1.2V_C210,
- * but exynos-cpufreq does not support
- * DT-based regulator lookup yet.
- */
- regulator-name = "vdd_arm";
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1350000>;
- regulator-always-on;
- };
-
- vint_breg: BUCK2 {
- regulator-name = "VINT_1.1V_C210";
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1100000>;
- regulator-always-on;
- };
-
- camisp_breg: BUCK4 {
- regulator-name = "CAM_ISP_CORE_1.2V";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- vmem_breg: BUCK5 {
- regulator-name = "VMEM_1.2V_C210";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-always-on;
- };
-
- vccsub_breg: BUCK7 {
- regulator-name = "VCC_SUB_2.0V";
- regulator-min-microvolt = <2000000>;
- regulator-max-microvolt = <2000000>;
- regulator-always-on;
- };
-
- safe1_sreg: ESAFEOUT1 {
- regulator-name = "SAFEOUT1";
- regulator-always-on;
- };
-
- safe2_sreg: ESAFEOUT2 {
- regulator-name = "SAFEOUT2";
- regulator-boot-on;
- };
- };
- };
- };
-
fixed-rate-clocks {
xxti {
compatible = "samsung,clock-xxti";
@@ -365,71 +134,6 @@
};
};
- dsi_0: dsi@11C80000 {
- vddcore-supply = <&vusb_reg>;
- vddio-supply = <&vmipi_reg>;
- samsung,pll-clock-frequency = <24000000>;
- status = "okay";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@1 {
- reg = <1>;
-
- dsi_out: endpoint {
- remote-endpoint = <&dsi_in>;
- samsung,burst-clock-frequency = <500000000>;
- samsung,esc-clock-frequency = <20000000>;
- };
- };
- };
-
- panel@0 {
- reg = <0>;
- compatible = "samsung,s6e8aa0";
- vdd3-supply = <&vcclcd_reg>;
- vci-supply = <&vlcd_reg>;
- reset-gpios = <&gpy4 5 0>;
- power-on-delay= <50>;
- reset-delay = <100>;
- init-delay = <100>;
- flip-horizontal;
- flip-vertical;
- panel-width-mm = <58>;
- panel-height-mm = <103>;
-
- display-timings {
- timing-0 {
- clock-frequency = <57153600>;
- hactive = <720>;
- vactive = <1280>;
- hfront-porch = <5>;
- hback-porch = <5>;
- hsync-len = <5>;
- vfront-porch = <13>;
- vback-porch = <1>;
- vsync-len = <2>;
- };
- };
-
- port {
- dsi_in: endpoint {
- remote-endpoint = <&dsi_out>;
- };
- };
- };
- };
-
- fimd@11c00000 {
- status = "okay";
- };
-
- tmu@100C0000 {
- status = "okay";
- };
-
thermal-zones {
cpu_thermal: cpu-thermal {
cooling-maps {
@@ -483,3 +187,299 @@
};
};
};
+
+&dsi_0 {
+ vddcore-supply = <&vusb_reg>;
+ vddio-supply = <&vmipi_reg>;
+ samsung,pll-clock-frequency = <24000000>;
+ status = "okay";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@1 {
+ reg = <1>;
+
+ dsi_out: endpoint {
+ remote-endpoint = <&dsi_in>;
+ samsung,burst-clock-frequency = <500000000>;
+ samsung,esc-clock-frequency = <20000000>;
+ };
+ };
+ };
+
+ panel@0 {
+ reg = <0>;
+ compatible = "samsung,s6e8aa0";
+ vdd3-supply = <&vcclcd_reg>;
+ vci-supply = <&vlcd_reg>;
+ reset-gpios = <&gpy4 5 0>;
+ power-on-delay= <50>;
+ reset-delay = <100>;
+ init-delay = <100>;
+ flip-horizontal;
+ flip-vertical;
+ panel-width-mm = <58>;
+ panel-height-mm = <103>;
+
+ display-timings {
+ timing-0 {
+ clock-frequency = <57153600>;
+ hactive = <720>;
+ vactive = <1280>;
+ hfront-porch = <5>;
+ hback-porch = <5>;
+ hsync-len = <5>;
+ vfront-porch = <13>;
+ vback-porch = <1>;
+ vsync-len = <2>;
+ };
+ };
+
+ port {
+ dsi_in: endpoint {
+ remote-endpoint = <&dsi_out>;
+ };
+ };
+ };
+};
+
+&exynos_usbphy {
+ status = "okay";
+};
+
+&fimd {
+ status = "okay";
+};
+
+&hsotg {
+ vusb_d-supply = <&vusb_reg>;
+ vusb_a-supply = <&vusbdac_reg>;
+ dr_mode = "peripheral";
+ status = "okay";
+};
+
+&i2c_3 {
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-slave-addr = <0x10>;
+ samsung,i2c-max-bus-freq = <400000>;
+ pinctrl-0 = <&i2c3_bus>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ mms114-touchscreen@48 {
+ compatible = "melfas,mms114";
+ reg = <0x48>;
+ interrupt-parent = <&gpx0>;
+ interrupts = <4 2>;
+ x-size = <720>;
+ y-size = <1280>;
+ avdd-supply = <&tsp_reg>;
+ vdd-supply = <&tsp_reg>;
+ };
+};
+
+&i2c_5 {
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-slave-addr = <0x10>;
+ samsung,i2c-max-bus-freq = <100000>;
+ pinctrl-0 = <&i2c5_bus>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ max8997_pmic@66 {
+ compatible = "maxim,max8997-pmic";
+
+ reg = <0x66>;
+
+ max8997,pmic-buck1-uses-gpio-dvs;
+ max8997,pmic-buck2-uses-gpio-dvs;
+ max8997,pmic-buck5-uses-gpio-dvs;
+
+ max8997,pmic-ignore-gpiodvs-side-effect;
+ max8997,pmic-buck125-default-dvs-idx = <0>;
+
+ max8997,pmic-buck125-dvs-gpios = <&gpx0 5 0>,
+ <&gpx0 6 0>,
+ <&gpl0 0 0>;
+
+ max8997,pmic-buck1-dvs-voltage = <1350000>, <1300000>,
+ <1250000>, <1200000>,
+ <1150000>, <1100000>,
+ <1000000>, <950000>;
+
+ max8997,pmic-buck2-dvs-voltage = <1100000>, <1000000>,
+ <950000>, <900000>,
+ <1100000>, <1000000>,
+ <950000>, <900000>;
+
+ max8997,pmic-buck5-dvs-voltage = <1200000>, <1200000>,
+ <1200000>, <1200000>,
+ <1200000>, <1200000>,
+ <1200000>, <1200000>;
+
+ regulators {
+ valive_reg: LDO2 {
+ regulator-name = "VALIVE_1.1V_C210";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ };
+
+ vusb_reg: LDO3 {
+ regulator-name = "VUSB_1.1V_C210";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ };
+
+ vmipi_reg: LDO4 {
+ regulator-name = "VMIPI_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vpda_reg: LDO6 {
+ regulator-name = "VCC_1.8V_PDA";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ vcam_reg: LDO7 {
+ regulator-name = "CAM_ISP_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vusbdac_reg: LDO8 {
+ regulator-name = "VUSB/VDAC_3.3V_C210";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ vccpda_reg: LDO9 {
+ regulator-name = "VCC_2.8V_PDA";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ };
+
+ vpll_reg: LDO10 {
+ regulator-name = "VPLL_1.1V_C210";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ };
+
+ vtcam_reg: LDO12 {
+ regulator-name = "VT_CAM_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vcclcd_reg: LDO13 {
+ regulator-name = "VCC_3.3V_LCD";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ vlcd_reg: LDO15 {
+ regulator-name = "VLCD_2.2V";
+ regulator-min-microvolt = <2200000>;
+ regulator-max-microvolt = <2200000>;
+ };
+
+ camsensor_reg: LDO16 {
+ regulator-name = "CAM_SENSOR_IO_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vddq_reg: LDO21 {
+ regulator-name = "VDDQ_M1M2_1.2V";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ };
+
+ varm_breg: BUCK1 {
+ /*
+ * HACK: The real name is VARM_1.2V_C210,
+ * but exynos-cpufreq does not support
+ * DT-based regulator lookup yet.
+ */
+ regulator-name = "vdd_arm";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ };
+
+ vint_breg: BUCK2 {
+ regulator-name = "VINT_1.1V_C210";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ };
+
+ camisp_breg: BUCK4 {
+ regulator-name = "CAM_ISP_CORE_1.2V";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ vmem_breg: BUCK5 {
+ regulator-name = "VMEM_1.2V_C210";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ };
+
+ vccsub_breg: BUCK7 {
+ regulator-name = "VCC_SUB_2.0V";
+ regulator-min-microvolt = <2000000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-always-on;
+ };
+
+ safe1_sreg: ESAFEOUT1 {
+ regulator-name = "SAFEOUT1";
+ regulator-always-on;
+ };
+
+ safe2_sreg: ESAFEOUT2 {
+ regulator-name = "SAFEOUT2";
+ regulator-boot-on;
+ };
+ };
+ };
+};
+
+&sdhci_0 {
+ bus-width = <8>;
+ non-removable;
+ pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus8>;
+ pinctrl-names = "default";
+ vmmc-supply = <&vemmc_reg>;
+ status = "okay";
+};
+
+&serial_0 {
+ status = "okay";
+};
+
+&serial_1 {
+ status = "okay";
+};
+
+&serial_2 {
+ status = "okay";
+};
+
+&serial_3 {
+ status = "okay";
+};
+
+&tmu {
+ status = "okay";
+};
--
2.1.0
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v3 06/11] ARM: dts: exynos4: Use labels for overriding nodes in Exynos4212
2015-04-17 13:47 [PATCH v3 00/11] ARM: dts: exynos4: labels for overriding nodes Krzysztof Kozlowski
` (4 preceding siblings ...)
2015-04-17 13:47 ` [PATCH v3 05/11] ARM: dts: exynos4: Use labels for overriding nodes in Trats Krzysztof Kozlowski
@ 2015-04-17 13:47 ` Krzysztof Kozlowski
2015-04-17 13:47 ` [PATCH v3 07/11] ARM: dts: exynos4: Use labels for overriding nodes in Exynos4x12 Krzysztof Kozlowski
` (4 subsequent siblings)
10 siblings, 0 replies; 12+ messages in thread
From: Krzysztof Kozlowski @ 2015-04-17 13:47 UTC (permalink / raw)
To: Kukjin Kim, devicetree, linux-arm-kernel, linux-samsung-soc,
linux-kernel
Cc: Arnd Bergmann, Olof Johansson, Krzysztof Kozlowski
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
---
arch/arm/boot/dts/exynos4212.dtsi | 12 ++++++------
1 file changed, 6 insertions(+), 6 deletions(-)
diff --git a/arch/arm/boot/dts/exynos4212.dtsi b/arch/arm/boot/dts/exynos4212.dtsi
index 5be03288f1ee..d9c8efeef208 100644
--- a/arch/arm/boot/dts/exynos4212.dtsi
+++ b/arch/arm/boot/dts/exynos4212.dtsi
@@ -41,12 +41,12 @@
reg = <0xA01>;
};
};
+};
- combiner: interrupt-controller@10440000 {
- samsung,combiner-nr = <18>;
- };
+&combiner {
+ samsung,combiner-nr = <18>;
+};
- gic: interrupt-controller@10490000 {
- cpu-offset = <0x8000>;
- };
+&gic {
+ cpu-offset = <0x8000>;
};
--
2.1.0
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v3 07/11] ARM: dts: exynos4: Use labels for overriding nodes in Exynos4x12
2015-04-17 13:47 [PATCH v3 00/11] ARM: dts: exynos4: labels for overriding nodes Krzysztof Kozlowski
` (5 preceding siblings ...)
2015-04-17 13:47 ` [PATCH v3 06/11] ARM: dts: exynos4: Use labels for overriding nodes in Exynos4212 Krzysztof Kozlowski
@ 2015-04-17 13:47 ` Krzysztof Kozlowski
2015-04-17 13:47 ` [PATCH v3 08/11] ARM: dts: exynos4: Use labels for overriding nodes in Exynos4412 Krzysztof Kozlowski
` (3 subsequent siblings)
10 siblings, 0 replies; 12+ messages in thread
From: Krzysztof Kozlowski @ 2015-04-17 13:47 UTC (permalink / raw)
To: Kukjin Kim, devicetree, linux-arm-kernel, linux-samsung-soc,
linux-kernel
Cc: Arnd Bergmann, Olof Johansson, Krzysztof Kozlowski
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
---
arch/arm/boot/dts/exynos4x12.dtsi | 210 +++++++++++++++++++-------------------
1 file changed, 105 insertions(+), 105 deletions(-)
diff --git a/arch/arm/boot/dts/exynos4x12.dtsi b/arch/arm/boot/dts/exynos4x12.dtsi
index 657b5ca39ce8..04812b842290 100644
--- a/arch/arm/boot/dts/exynos4x12.dtsi
+++ b/arch/arm/boot/dts/exynos4x12.dtsi
@@ -96,32 +96,6 @@
};
};
- combiner: interrupt-controller@10440000 {
- interrupts = <0 0 0>, <0 1 0>, <0 2 0>, <0 3 0>,
- <0 4 0>, <0 5 0>, <0 6 0>, <0 7 0>,
- <0 8 0>, <0 9 0>, <0 10 0>, <0 11 0>,
- <0 12 0>, <0 13 0>, <0 14 0>, <0 15 0>,
- <0 107 0>, <0 108 0>, <0 48 0>, <0 42 0>;
- };
-
- pinctrl_0: pinctrl@11400000 {
- compatible = "samsung,exynos4x12-pinctrl";
- reg = <0x11400000 0x1000>;
- interrupts = <0 47 0>;
- };
-
- pinctrl_1: pinctrl@11000000 {
- compatible = "samsung,exynos4x12-pinctrl";
- reg = <0x11000000 0x1000>;
- interrupts = <0 46 0>;
-
- wakup_eint: wakeup-interrupt-controller {
- compatible = "samsung,exynos4210-wakeup-eint";
- interrupt-parent = <&gic>;
- interrupts = <0 32 0>;
- };
- };
-
adc: adc@126C0000 {
compatible = "samsung,exynos-adc-v1";
reg = <0x126C0000 0x100>;
@@ -135,30 +109,6 @@
status = "disabled";
};
- pinctrl_2: pinctrl@03860000 {
- compatible = "samsung,exynos4x12-pinctrl";
- reg = <0x03860000 0x1000>;
- interrupt-parent = <&combiner>;
- interrupts = <10 0>;
- };
-
- pinctrl_3: pinctrl@106E0000 {
- compatible = "samsung,exynos4x12-pinctrl";
- reg = <0x106E0000 0x1000>;
- interrupts = <0 72 0>;
- };
-
- pmu_system_controller: system-controller@10020000 {
- compatible = "samsung,exynos4212-pmu", "syscon";
- clock-names = "clkout0", "clkout1", "clkout2", "clkout3",
- "clkout4", "clkout8", "clkout9";
- clocks = <&clock CLK_OUT_DMC>, <&clock CLK_OUT_TOP>,
- <&clock CLK_OUT_LEFTBUS>, <&clock CLK_OUT_RIGHTBUS>,
- <&clock CLK_OUT_CPU>, <&clock CLK_XXTI>,
- <&clock CLK_XUSBXTI>;
- #clock-cells = <1>;
- };
-
g2d: g2d@10800000 {
compatible = "samsung,exynos4212-g2d";
reg = <0x10800000 0x1000>;
@@ -173,40 +123,7 @@
<&clock CLK_PIXELASYNCM0>, <&clock CLK_PIXELASYNCM1>;
clock-names = "sclk_cam0", "sclk_cam1", "pxl_async0", "pxl_async1";
- fimc_0: fimc@11800000 {
- compatible = "samsung,exynos4212-fimc";
- samsung,pix-limits = <4224 8192 1920 4224>;
- samsung,mainscaler-ext;
- samsung,isp-wb;
- samsung,cam-if;
- };
-
- fimc_1: fimc@11810000 {
- compatible = "samsung,exynos4212-fimc";
- samsung,pix-limits = <4224 8192 1920 4224>;
- samsung,mainscaler-ext;
- samsung,isp-wb;
- samsung,cam-if;
- };
-
- fimc_2: fimc@11820000 {
- compatible = "samsung,exynos4212-fimc";
- samsung,pix-limits = <4224 8192 1920 4224>;
- samsung,mainscaler-ext;
- samsung,isp-wb;
- samsung,lcd-wb;
- samsung,cam-if;
- };
-
- fimc_3: fimc@11830000 {
- compatible = "samsung,exynos4212-fimc";
- samsung,pix-limits = <1920 8192 1366 1920>;
- samsung,rotators = <0>;
- samsung,mainscaler-ext;
- samsung,isp-wb;
- samsung,lcd-wb;
- };
-
+ /* fimc_[0-3] are configured outside, under phandles */
fimc_lite_0: fimc-lite@12390000 {
compatible = "samsung,exynos4212-fimc-lite";
reg = <0x12390000 0x1000>;
@@ -283,30 +200,113 @@
clock-names = "biu", "ciu";
status = "disabled";
};
+};
- exynos-usbphy@125B0000 {
- compatible = "samsung,exynos4x12-usb2-phy";
- samsung,sysreg-phandle = <&sys_reg>;
- };
+&combiner {
+ interrupts = <0 0 0>, <0 1 0>, <0 2 0>, <0 3 0>,
+ <0 4 0>, <0 5 0>, <0 6 0>, <0 7 0>,
+ <0 8 0>, <0 9 0>, <0 10 0>, <0 11 0>,
+ <0 12 0>, <0 13 0>, <0 14 0>, <0 15 0>,
+ <0 107 0>, <0 108 0>, <0 48 0>, <0 42 0>;
+};
- tmu@100C0000 {
- compatible = "samsung,exynos4412-tmu";
- interrupt-parent = <&combiner>;
- interrupts = <2 4>;
- reg = <0x100C0000 0x100>;
- clocks = <&clock 383>;
- clock-names = "tmu_apbif";
- status = "disabled";
- };
+&exynos_usbphy {
+ compatible = "samsung,exynos4x12-usb2-phy";
+ samsung,sysreg-phandle = <&sys_reg>;
+};
- hdmi: hdmi@12D00000 {
- compatible = "samsung,exynos4212-hdmi";
- };
+&fimc_0 {
+ compatible = "samsung,exynos4212-fimc";
+ samsung,pix-limits = <4224 8192 1920 4224>;
+ samsung,mainscaler-ext;
+ samsung,isp-wb;
+ samsung,cam-if;
+};
+
+&fimc_1 {
+ compatible = "samsung,exynos4212-fimc";
+ samsung,pix-limits = <4224 8192 1920 4224>;
+ samsung,mainscaler-ext;
+ samsung,isp-wb;
+ samsung,cam-if;
+};
+
+&fimc_2 {
+ compatible = "samsung,exynos4212-fimc";
+ samsung,pix-limits = <4224 8192 1920 4224>;
+ samsung,mainscaler-ext;
+ samsung,isp-wb;
+ samsung,lcd-wb;
+ samsung,cam-if;
+};
+
+&fimc_3 {
+ compatible = "samsung,exynos4212-fimc";
+ samsung,pix-limits = <1920 8192 1366 1920>;
+ samsung,rotators = <0>;
+ samsung,mainscaler-ext;
+ samsung,isp-wb;
+ samsung,lcd-wb;
+};
+
+&hdmi {
+ compatible = "samsung,exynos4212-hdmi";
+};
- mixer: mixer@12C10000 {
- compatible = "samsung,exynos4212-mixer";
- clock-names = "mixer", "hdmi", "sclk_hdmi", "vp";
- clocks = <&clock CLK_MIXER>, <&clock CLK_HDMI>,
- <&clock CLK_SCLK_HDMI>, <&clock CLK_VP>;
+&mixer {
+ compatible = "samsung,exynos4212-mixer";
+ clock-names = "mixer", "hdmi", "sclk_hdmi", "vp";
+ clocks = <&clock CLK_MIXER>, <&clock CLK_HDMI>,
+ <&clock CLK_SCLK_HDMI>, <&clock CLK_VP>;
+};
+
+&pinctrl_0 {
+ compatible = "samsung,exynos4x12-pinctrl";
+ reg = <0x11400000 0x1000>;
+ interrupts = <0 47 0>;
+};
+
+&pinctrl_1 {
+ compatible = "samsung,exynos4x12-pinctrl";
+ reg = <0x11000000 0x1000>;
+ interrupts = <0 46 0>;
+
+ wakup_eint: wakeup-interrupt-controller {
+ compatible = "samsung,exynos4210-wakeup-eint";
+ interrupt-parent = <&gic>;
+ interrupts = <0 32 0>;
};
};
+
+&pinctrl_2 {
+ compatible = "samsung,exynos4x12-pinctrl";
+ reg = <0x03860000 0x1000>;
+ interrupt-parent = <&combiner>;
+ interrupts = <10 0>;
+};
+
+&pinctrl_3 {
+ compatible = "samsung,exynos4x12-pinctrl";
+ reg = <0x106E0000 0x1000>;
+ interrupts = <0 72 0>;
+};
+
+&pmu_system_controller {
+ compatible = "samsung,exynos4212-pmu", "syscon";
+ clock-names = "clkout0", "clkout1", "clkout2", "clkout3",
+ "clkout4", "clkout8", "clkout9";
+ clocks = <&clock CLK_OUT_DMC>, <&clock CLK_OUT_TOP>,
+ <&clock CLK_OUT_LEFTBUS>, <&clock CLK_OUT_RIGHTBUS>,
+ <&clock CLK_OUT_CPU>, <&clock CLK_XXTI>, <&clock CLK_XUSBXTI>;
+ #clock-cells = <1>;
+};
+
+&tmu {
+ compatible = "samsung,exynos4412-tmu";
+ interrupt-parent = <&combiner>;
+ interrupts = <2 4>;
+ reg = <0x100C0000 0x100>;
+ clocks = <&clock 383>;
+ clock-names = "tmu_apbif";
+ status = "disabled";
+};
--
2.1.0
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v3 08/11] ARM: dts: exynos4: Use labels for overriding nodes in Exynos4412
2015-04-17 13:47 [PATCH v3 00/11] ARM: dts: exynos4: labels for overriding nodes Krzysztof Kozlowski
` (6 preceding siblings ...)
2015-04-17 13:47 ` [PATCH v3 07/11] ARM: dts: exynos4: Use labels for overriding nodes in Exynos4x12 Krzysztof Kozlowski
@ 2015-04-17 13:47 ` Krzysztof Kozlowski
2015-04-17 13:47 ` [PATCH v3 09/11] ARM: dts: exynos4: Use labels for overriding nodes in Odroid Krzysztof Kozlowski
` (2 subsequent siblings)
10 siblings, 0 replies; 12+ messages in thread
From: Krzysztof Kozlowski @ 2015-04-17 13:47 UTC (permalink / raw)
To: Kukjin Kim, devicetree, linux-arm-kernel, linux-samsung-soc,
linux-kernel
Cc: Arnd Bergmann, Olof Johansson, Krzysztof Kozlowski
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
---
arch/arm/boot/dts/exynos4412.dtsi | 20 ++++++++++----------
1 file changed, 10 insertions(+), 10 deletions(-)
diff --git a/arch/arm/boot/dts/exynos4412.dtsi b/arch/arm/boot/dts/exynos4412.dtsi
index 68ad43b391ae..b78ada70bd05 100644
--- a/arch/arm/boot/dts/exynos4412.dtsi
+++ b/arch/arm/boot/dts/exynos4412.dtsi
@@ -54,19 +54,19 @@
};
};
- combiner: interrupt-controller@10440000 {
- samsung,combiner-nr = <20>;
- };
-
pmu {
interrupts = <2 2>, <3 2>, <18 2>, <19 2>;
};
+};
- gic: interrupt-controller@10490000 {
- cpu-offset = <0x4000>;
- };
+&pmu_system_controller {
+ compatible = "samsung,exynos4412-pmu", "syscon";
+};
- pmu_system_controller: system-controller@10020000 {
- compatible = "samsung,exynos4412-pmu", "syscon";
- };
+&combiner {
+ samsung,combiner-nr = <20>;
+};
+
+&gic {
+ cpu-offset = <0x4000>;
};
--
2.1.0
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v3 09/11] ARM: dts: exynos4: Use labels for overriding nodes in Odroid
2015-04-17 13:47 [PATCH v3 00/11] ARM: dts: exynos4: labels for overriding nodes Krzysztof Kozlowski
` (7 preceding siblings ...)
2015-04-17 13:47 ` [PATCH v3 08/11] ARM: dts: exynos4: Use labels for overriding nodes in Exynos4412 Krzysztof Kozlowski
@ 2015-04-17 13:47 ` Krzysztof Kozlowski
2015-04-17 13:47 ` [PATCH v3 10/11] ARM: dts: exynos4: Use labels for overriding nodes in SMDK4412 Krzysztof Kozlowski
2015-04-17 13:47 ` [PATCH v3 11/11] ARM: dts: exynos4: Use labels for overriding nodes in Trats2 Krzysztof Kozlowski
10 siblings, 0 replies; 12+ messages in thread
From: Krzysztof Kozlowski @ 2015-04-17 13:47 UTC (permalink / raw)
To: Kukjin Kim, devicetree, linux-arm-kernel, linux-samsung-soc,
linux-kernel
Cc: Arnd Bergmann, Olof Johansson, Krzysztof Kozlowski
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
---
arch/arm/boot/dts/exynos4412-odroid-common.dtsi | 728 ++++++++++++------------
arch/arm/boot/dts/exynos4412-odroidx.dts | 16 +-
2 files changed, 372 insertions(+), 372 deletions(-)
diff --git a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
index 8de12af7c276..6801ee6c4449 100644
--- a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
+++ b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
@@ -37,16 +37,6 @@
};
};
- i2s0: i2s@03830000 {
- pinctrl-0 = <&i2s0_bus>;
- pinctrl-names = "default";
- status = "okay";
- clocks = <&clock_audss EXYNOS_I2S_BUS>,
- <&clock_audss EXYNOS_DOUT_AUD_BUS>,
- <&clock_audss EXYNOS_SCLK_I2S>;
- clock-names = "iis", "i2s_opclk0", "i2s_opclk1";
- };
-
sound: sound {
compatible = "simple-audio-card";
assigned-clocks = <&clock_audss EXYNOS_MOUT_AUDSS>,
@@ -82,425 +72,435 @@
reset-gpios = <&gpk1 2 1>;
};
- mmc@12550000 {
- pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>;
- pinctrl-names = "default";
- vmmc-supply = <&ldo20_reg &buck8_reg>;
- mmc-pwrseq = <&emmc_pwrseq>;
- status = "okay";
-
- num-slots = <1>;
- broken-cd;
- card-detect-delay = <200>;
- samsung,dw-mshc-ciu-div = <3>;
- samsung,dw-mshc-sdr-timing = <2 3>;
- samsung,dw-mshc-ddr-timing = <1 2>;
- bus-width = <8>;
- cap-mmc-highspeed;
- };
-
- watchdog@10060000 {
- status = "okay";
- };
-
- rtc@10070000 {
- status = "okay";
- };
-
- g2d@10800000 {
- status = "okay";
- };
-
camera {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <>;
+ };
- fimc_0: fimc@11800000 {
- status = "okay";
- assigned-clocks = <&clock CLK_MOUT_FIMC0>,
- <&clock CLK_SCLK_FIMC0>;
- assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
- assigned-clock-rates = <0>, <176000000>;
- };
-
- fimc_1: fimc@11810000 {
- status = "okay";
- assigned-clocks = <&clock CLK_MOUT_FIMC1>,
- <&clock CLK_SCLK_FIMC1>;
- assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
- assigned-clock-rates = <0>, <176000000>;
+ fixed-rate-clocks {
+ xxti {
+ compatible = "samsung,clock-xxti";
+ clock-frequency = <0>;
};
- fimc_2: fimc@11820000 {
- status = "okay";
- assigned-clocks = <&clock CLK_MOUT_FIMC2>,
- <&clock CLK_SCLK_FIMC2>;
- assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
- assigned-clock-rates = <0>, <176000000>;
+ xusbxti {
+ compatible = "samsung,clock-xusbxti";
+ clock-frequency = <24000000>;
};
+ };
- fimc_3: fimc@11830000 {
- status = "okay";
- assigned-clocks = <&clock CLK_MOUT_FIMC3>,
- <&clock CLK_SCLK_FIMC3>;
- assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
- assigned-clock-rates = <0>, <176000000>;
+ thermal-zones {
+ cpu_thermal: cpu-thermal {
+ cooling-maps {
+ map0 {
+ /* Corresponds to 800MHz at freq_table */
+ cooling-device = <&cpu0 7 7>;
+ };
+ map1 {
+ /* Corresponds to 200MHz at freq_table */
+ cooling-device = <&cpu0 13 13>;
+ };
+ };
};
};
+};
- sdhci@12530000 {
- bus-width = <4>;
- pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
- pinctrl-names = "default";
- vmmc-supply = <&ldo4_reg &ldo21_reg>;
- cd-gpios = <&gpk2 2 0>;
- cd-inverted;
- status = "okay";
- };
+/* RSTN signal for eMMC */
+&sd1_cd {
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+};
- serial@13800000 {
- status = "okay";
+&pinctrl_1 {
+ gpio_power_key: power_key {
+ samsung,pins = "gpx1-3";
+ samsung,pin-pud = <0>;
};
- serial@13810000 {
- status = "okay";
+ max77686_irq: max77686-irq {
+ samsung,pins = "gpx3-2";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
};
- fixed-rate-clocks {
- xxti {
- compatible = "samsung,clock-xxti";
- clock-frequency = <0>;
- };
-
- xusbxti {
- compatible = "samsung,clock-xusbxti";
- clock-frequency = <24000000>;
- };
+ hdmi_hpd: hdmi-hpd {
+ samsung,pins = "gpx3-7";
+ samsung,pin-pud = <1>;
};
+};
- i2c@13860000 {
- pinctrl-0 = <&i2c0_bus>;
- pinctrl-names = "default";
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-max-bus-freq = <400000>;
- status = "okay";
+&ehci {
+ status = "okay";
+};
- usb3503: usb3503@08 {
- compatible = "smsc,usb3503";
- reg = <0x08>;
+&exynos_usbphy {
+ status = "okay";
+};
- intn-gpios = <&gpx3 0 0>;
- connect-gpios = <&gpx3 4 0>;
- reset-gpios = <&gpx3 5 0>;
- initial-mode = <1>;
- };
+&fimc_0 {
+ status = "okay";
+ assigned-clocks = <&clock CLK_MOUT_FIMC0>,
+ <&clock CLK_SCLK_FIMC0>;
+ assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
+ assigned-clock-rates = <0>, <176000000>;
+};
- max77686: pmic@09 {
- compatible = "maxim,max77686";
- interrupt-parent = <&gpx3>;
- interrupts = <2 0>;
- pinctrl-names = "default";
- pinctrl-0 = <&max77686_irq>;
- reg = <0x09>;
- #clock-cells = <1>;
-
- voltage-regulators {
- ldo1_reg: LDO1 {
- regulator-name = "VDD_ALIVE_1.0V";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- };
+&fimc_1 {
+ status = "okay";
+ assigned-clocks = <&clock CLK_MOUT_FIMC1>,
+ <&clock CLK_SCLK_FIMC1>;
+ assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
+ assigned-clock-rates = <0>, <176000000>;
+};
- ldo2_reg: LDO2 {
- regulator-name = "VDDQ_M1_2_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
+&fimc_2 {
+ status = "okay";
+ assigned-clocks = <&clock CLK_MOUT_FIMC2>,
+ <&clock CLK_SCLK_FIMC2>;
+ assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
+ assigned-clock-rates = <0>, <176000000>;
+};
- ldo3_reg: LDO3 {
- regulator-name = "VDDQ_EXT_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
+&fimc_3 {
+ status = "okay";
+ assigned-clocks = <&clock CLK_MOUT_FIMC3>,
+ <&clock CLK_SCLK_FIMC3>;
+ assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
+ assigned-clock-rates = <0>, <176000000>;
+};
- ldo4_reg: LDO4 {
- regulator-name = "VDDQ_MMC2_2.8V";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- regulator-always-on;
- regulator-boot-on;
- };
+&g2d {
+ status = "okay";
+};
- ldo5_reg: LDO5 {
- regulator-name = "VDDQ_MMC1_3_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
+&hdmi {
+ hpd-gpio = <&gpx3 7 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&hdmi_hpd>;
+ vdd-supply = <&ldo8_reg>;
+ vdd_osc-supply = <&ldo10_reg>;
+ vdd_pll-supply = <&ldo8_reg>;
+ ddc = <&i2c_2>;
+ status = "okay";
+};
- ldo6_reg: LDO6 {
- regulator-name = "VDD10_MPLL_1.0V";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- };
+&hsotg {
+ dr_mode = "peripheral";
+ status = "okay";
+ vusb_d-supply = <&ldo15_reg>;
+ vusb_a-supply = <&ldo12_reg>;
+};
- ldo7_reg: LDO7 {
- regulator-name = "VDD10_XPLL_1.0V";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- };
+&i2c_0 {
+ pinctrl-0 = <&i2c0_bus>;
+ pinctrl-names = "default";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <400000>;
+ status = "okay";
+
+ usb3503: usb3503@08 {
+ compatible = "smsc,usb3503";
+ reg = <0x08>;
+
+ intn-gpios = <&gpx3 0 0>;
+ connect-gpios = <&gpx3 4 0>;
+ reset-gpios = <&gpx3 5 0>;
+ initial-mode = <1>;
+ };
- ldo8_reg: ldo@8 {
- regulator-compatible = "LDO8";
- regulator-name = "VDD10_HDMI_1.0V";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- };
+ max77686: pmic@09 {
+ compatible = "maxim,max77686";
+ interrupt-parent = <&gpx3>;
+ interrupts = <2 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&max77686_irq>;
+ reg = <0x09>;
+ #clock-cells = <1>;
+
+ voltage-regulators {
+ ldo1_reg: LDO1 {
+ regulator-name = "VDD_ALIVE_1.0V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
- ldo10_reg: ldo@10 {
- regulator-compatible = "LDO10";
- regulator-name = "VDDQ_MIPIHSI_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
+ ldo2_reg: LDO2 {
+ regulator-name = "VDDQ_M1_2_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
- ldo11_reg: LDO11 {
- regulator-name = "VDD18_ABB1_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
+ ldo3_reg: LDO3 {
+ regulator-name = "VDDQ_EXT_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
- ldo12_reg: LDO12 {
- regulator-name = "VDD33_USB_3.3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo4_reg: LDO4 {
+ regulator-name = "VDDQ_MMC2_2.8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- ldo13_reg: LDO13 {
- regulator-name = "VDDQ_C2C_W_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo5_reg: LDO5 {
+ regulator-name = "VDDQ_MMC1_3_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- ldo14_reg: LDO14 {
- regulator-name = "VDD18_ABB0_2_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo6_reg: LDO6 {
+ regulator-name = "VDD10_MPLL_1.0V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
- ldo15_reg: LDO15 {
- regulator-name = "VDD10_HSIC_1.0V";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo7_reg: LDO7 {
+ regulator-name = "VDD10_XPLL_1.0V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
- ldo16_reg: LDO16 {
- regulator-name = "VDD18_HSIC_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo8_reg: ldo@8 {
+ regulator-compatible = "LDO8";
+ regulator-name = "VDD10_HDMI_1.0V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ };
- ldo20_reg: LDO20 {
- regulator-name = "LDO20_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-boot-on;
- };
+ ldo10_reg: ldo@10 {
+ regulator-compatible = "LDO10";
+ regulator-name = "VDDQ_MIPIHSI_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
- ldo21_reg: LDO21 {
- regulator-name = "LDO21_3.3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo11_reg: LDO11 {
+ regulator-name = "VDD18_ABB1_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
- ldo25_reg: LDO25 {
- regulator-name = "VDDQ_LCD_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo12_reg: LDO12 {
+ regulator-name = "VDD33_USB_3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- buck1_reg: BUCK1 {
- regulator-name = "vdd_mif";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo13_reg: LDO13 {
+ regulator-name = "VDDQ_C2C_W_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- buck2_reg: BUCK2 {
- regulator-name = "vdd_arm";
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1350000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo14_reg: LDO14 {
+ regulator-name = "VDD18_ABB0_2_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- buck3_reg: BUCK3 {
- regulator-name = "vdd_int";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo15_reg: LDO15 {
+ regulator-name = "VDD10_HSIC_1.0V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- buck4_reg: BUCK4 {
- regulator-name = "vdd_g3d";
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1100000>;
- regulator-microvolt-offset = <50000>;
- };
+ ldo16_reg: LDO16 {
+ regulator-name = "VDD18_HSIC_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- buck5_reg: BUCK5 {
- regulator-name = "VDDQ_CKEM1_2_1.2V";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo20_reg: LDO20 {
+ regulator-name = "LDO20_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ };
- buck6_reg: BUCK6 {
- regulator-name = "BUCK6_1.35V";
- regulator-min-microvolt = <1350000>;
- regulator-max-microvolt = <1350000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo21_reg: LDO21 {
+ regulator-name = "LDO21_3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- buck7_reg: BUCK7 {
- regulator-name = "BUCK7_2.0V";
- regulator-min-microvolt = <2000000>;
- regulator-max-microvolt = <2000000>;
- regulator-always-on;
- };
+ ldo25_reg: LDO25 {
+ regulator-name = "VDDQ_LCD_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- buck8_reg: BUCK8 {
- regulator-name = "BUCK8_2.8V";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- };
+ buck1_reg: BUCK1 {
+ regulator-name = "vdd_mif";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ regulator-boot-on;
};
- };
- };
- i2c@13870000 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_bus>;
- status = "okay";
- max98090: max98090@10 {
- compatible = "maxim,max98090";
- reg = <0x10>;
- interrupt-parent = <&gpx0>;
- interrupts = <0 0>;
- clocks = <&i2s0 CLK_I2S_CDCLK>;
- clock-names = "mclk";
- #sound-dai-cells = <0>;
- };
- };
+ buck2_reg: BUCK2 {
+ regulator-name = "vdd_arm";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- exynos-usbphy@125B0000 {
- status = "okay";
- };
+ buck3_reg: BUCK3 {
+ regulator-name = "vdd_int";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- hsotg@12480000 {
- dr_mode = "peripheral";
- status = "okay";
- vusb_d-supply = <&ldo15_reg>;
- vusb_a-supply = <&ldo12_reg>;
- };
+ buck4_reg: BUCK4 {
+ regulator-name = "vdd_g3d";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-microvolt-offset = <50000>;
+ };
- ehci: ehci@12580000 {
- status = "okay";
- };
+ buck5_reg: BUCK5 {
+ regulator-name = "VDDQ_CKEM1_2_1.2V";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- tmu@100C0000 {
- vtmu-supply = <&ldo10_reg>;
- status = "okay";
- };
+ buck6_reg: BUCK6 {
+ regulator-name = "BUCK6_1.35V";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- thermal-zones {
- cpu_thermal: cpu-thermal {
- cooling-maps {
- map0 {
- /* Corresponds to 800MHz at freq_table */
- cooling-device = <&cpu0 7 7>;
- };
- map1 {
- /* Corresponds to 200MHz at freq_table */
- cooling-device = <&cpu0 13 13>;
- };
- };
+ buck7_reg: BUCK7 {
+ regulator-name = "BUCK7_2.0V";
+ regulator-min-microvolt = <2000000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-always-on;
+ };
+
+ buck8_reg: BUCK8 {
+ regulator-name = "BUCK8_2.8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
};
};
+};
- mixer: mixer@12C10000 {
- status = "okay";
+&i2c_1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_bus>;
+ status = "okay";
+ max98090: max98090@10 {
+ compatible = "maxim,max98090";
+ reg = <0x10>;
+ interrupt-parent = <&gpx0>;
+ interrupts = <0 0>;
+ clocks = <&i2s0 CLK_I2S_CDCLK>;
+ clock-names = "mclk";
+ #sound-dai-cells = <0>;
};
+};
- hdmi@12D00000 {
- hpd-gpio = <&gpx3 7 0>;
- pinctrl-names = "default";
- pinctrl-0 = <&hdmi_hpd>;
- vdd-supply = <&ldo8_reg>;
- vdd_osc-supply = <&ldo10_reg>;
- vdd_pll-supply = <&ldo8_reg>;
- ddc = <&hdmi_ddc>;
- status = "okay";
- };
+&i2c_2 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_bus>;
+};
- hdmi_ddc: i2c@13880000 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_bus>;
- };
+&i2c_8 {
+ status = "okay";
+};
- i2c@138E0000 {
- status = "okay";
- };
+&i2s0 {
+ pinctrl-0 = <&i2s0_bus>;
+ pinctrl-names = "default";
+ status = "okay";
+ clocks = <&clock_audss EXYNOS_I2S_BUS>,
+ <&clock_audss EXYNOS_DOUT_AUD_BUS>,
+ <&clock_audss EXYNOS_SCLK_I2S>;
+ clock-names = "iis", "i2s_opclk0", "i2s_opclk1";
};
-/* RSTN signal for eMMC */
-&sd1_cd {
- samsung,pin-pud = <0>;
- samsung,pin-drv = <0>;
+&mixer {
+ status = "okay";
};
-&pinctrl_1 {
- gpio_power_key: power_key {
- samsung,pins = "gpx1-3";
- samsung,pin-pud = <0>;
- };
+&mshc_0 {
+ pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>;
+ pinctrl-names = "default";
+ vmmc-supply = <&ldo20_reg &buck8_reg>;
+ mmc-pwrseq = <&emmc_pwrseq>;
+ status = "okay";
+
+ num-slots = <1>;
+ broken-cd;
+ card-detect-delay = <200>;
+ samsung,dw-mshc-ciu-div = <3>;
+ samsung,dw-mshc-sdr-timing = <2 3>;
+ samsung,dw-mshc-ddr-timing = <1 2>;
+ bus-width = <8>;
+ cap-mmc-highspeed;
+};
- max77686_irq: max77686-irq {
- samsung,pins = "gpx3-2";
- samsung,pin-function = <0>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <0>;
- };
+&rtc {
+ status = "okay";
+};
- hdmi_hpd: hdmi-hpd {
- samsung,pins = "gpx3-7";
- samsung,pin-pud = <1>;
- };
+&sdhci_2 {
+ bus-width = <4>;
+ pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
+ pinctrl-names = "default";
+ vmmc-supply = <&ldo4_reg &ldo21_reg>;
+ cd-gpios = <&gpk2 2 0>;
+ cd-inverted;
+ status = "okay";
+};
+
+&serial_0 {
+ status = "okay";
+};
+
+&serial_1 {
+ status = "okay";
+};
+
+&tmu {
+ vtmu-supply = <&ldo10_reg>;
+ status = "okay";
+};
+
+&watchdog {
+ status = "okay";
};
diff --git a/arch/arm/boot/dts/exynos4412-odroidx.dts b/arch/arm/boot/dts/exynos4412-odroidx.dts
index cb1cfe7239c4..679ac103ebf6 100644
--- a/arch/arm/boot/dts/exynos4412-odroidx.dts
+++ b/arch/arm/boot/dts/exynos4412-odroidx.dts
@@ -38,14 +38,6 @@
};
};
- serial@13820000 {
- status = "okay";
- };
-
- serial@13830000 {
- status = "okay";
- };
-
gpio_keys {
pinctrl-0 = <&gpio_power_key &gpio_home_key>;
@@ -83,3 +75,11 @@
samsung,pin-pud = <0>;
};
};
+
+&serial_2 {
+ status = "okay";
+};
+
+&serial_3 {
+ status = "okay";
+};
--
2.1.0
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v3 10/11] ARM: dts: exynos4: Use labels for overriding nodes in SMDK4412
2015-04-17 13:47 [PATCH v3 00/11] ARM: dts: exynos4: labels for overriding nodes Krzysztof Kozlowski
` (8 preceding siblings ...)
2015-04-17 13:47 ` [PATCH v3 09/11] ARM: dts: exynos4: Use labels for overriding nodes in Odroid Krzysztof Kozlowski
@ 2015-04-17 13:47 ` Krzysztof Kozlowski
2015-04-17 13:47 ` [PATCH v3 11/11] ARM: dts: exynos4: Use labels for overriding nodes in Trats2 Krzysztof Kozlowski
10 siblings, 0 replies; 12+ messages in thread
From: Krzysztof Kozlowski @ 2015-04-17 13:47 UTC (permalink / raw)
To: Kukjin Kim, devicetree, linux-arm-kernel, linux-samsung-soc,
linux-kernel
Cc: Arnd Bergmann, Olof Johansson, Krzysztof Kozlowski
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
---
arch/arm/boot/dts/exynos4412-smdk4412.dts | 210 +++++++++++++++---------------
1 file changed, 105 insertions(+), 105 deletions(-)
diff --git a/arch/arm/boot/dts/exynos4412-smdk4412.dts b/arch/arm/boot/dts/exynos4412-smdk4412.dts
index b9256afbcc68..c2421df1fa43 100644
--- a/arch/arm/boot/dts/exynos4412-smdk4412.dts
+++ b/arch/arm/boot/dts/exynos4412-smdk4412.dts
@@ -28,135 +28,135 @@
stdout-path = &serial_1;
};
- g2d@10800000 {
- status = "okay";
- };
-
- pinctrl@11000000 {
- keypad_rows: keypad-rows {
- samsung,pins = "gpx2-0", "gpx2-1", "gpx2-2";
- samsung,pin-function = <3>;
- samsung,pin-pud = <3>;
- samsung,pin-drv = <0>;
+ fixed-rate-clocks {
+ xxti {
+ compatible = "samsung,clock-xxti";
+ clock-frequency = <0>;
};
- keypad_cols: keypad-cols {
- samsung,pins = "gpx1-0", "gpx1-1", "gpx1-2", "gpx1-3",
- "gpx1-4", "gpx1-5", "gpx1-6", "gpx1-7";
- samsung,pin-function = <3>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <0>;
+ xusbxti {
+ compatible = "samsung,clock-xusbxti";
+ clock-frequency = <24000000>;
};
};
+};
- keypad@100A0000 {
- samsung,keypad-num-rows = <3>;
- samsung,keypad-num-columns = <8>;
- linux,keypad-no-autorepeat;
- linux,keypad-wakeup;
- pinctrl-0 = <&keypad_rows &keypad_cols>;
- pinctrl-names = "default";
- status = "okay";
-
- key_1 {
- keypad,row = <1>;
- keypad,column = <3>;
- linux,code = <2>;
- };
-
- key_2 {
- keypad,row = <1>;
- keypad,column = <4>;
- linux,code = <3>;
- };
-
- key_3 {
- keypad,row = <1>;
- keypad,column = <5>;
- linux,code = <4>;
- };
-
- key_4 {
- keypad,row = <1>;
- keypad,column = <6>;
- linux,code = <5>;
- };
+&g2d {
+ status = "okay";
+};
- key_5 {
- keypad,row = <1>;
- keypad,column = <7>;
- linux,code = <6>;
- };
+&keypad {
+ samsung,keypad-num-rows = <3>;
+ samsung,keypad-num-columns = <8>;
+ linux,keypad-no-autorepeat;
+ linux,keypad-wakeup;
+ pinctrl-0 = <&keypad_rows &keypad_cols>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ key_1 {
+ keypad,row = <1>;
+ keypad,column = <3>;
+ linux,code = <2>;
+ };
- key_A {
- keypad,row = <2>;
- keypad,column = <6>;
- linux,code = <30>;
- };
+ key_2 {
+ keypad,row = <1>;
+ keypad,column = <4>;
+ linux,code = <3>;
+ };
- key_B {
- keypad,row = <2>;
- keypad,column = <7>;
- linux,code = <48>;
- };
+ key_3 {
+ keypad,row = <1>;
+ keypad,column = <5>;
+ linux,code = <4>;
+ };
- key_C {
- keypad,row = <0>;
- keypad,column = <5>;
- linux,code = <46>;
- };
+ key_4 {
+ keypad,row = <1>;
+ keypad,column = <6>;
+ linux,code = <5>;
+ };
- key_D {
- keypad,row = <2>;
- keypad,column = <5>;
- linux,code = <32>;
- };
+ key_5 {
+ keypad,row = <1>;
+ keypad,column = <7>;
+ linux,code = <6>;
+ };
- key_E {
- keypad,row = <0>;
- keypad,column = <7>;
- linux,code = <18>;
- };
+ key_A {
+ keypad,row = <2>;
+ keypad,column = <6>;
+ linux,code = <30>;
};
- sdhci@12530000 {
- bus-width = <4>;
- pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &sd2_cd>;
- pinctrl-names = "default";
- status = "okay";
+ key_B {
+ keypad,row = <2>;
+ keypad,column = <7>;
+ linux,code = <48>;
};
- codec@13400000 {
- samsung,mfc-r = <0x43000000 0x800000>;
- samsung,mfc-l = <0x51000000 0x800000>;
- status = "okay";
+ key_C {
+ keypad,row = <0>;
+ keypad,column = <5>;
+ linux,code = <46>;
};
- serial@13800000 {
- status = "okay";
+ key_D {
+ keypad,row = <2>;
+ keypad,column = <5>;
+ linux,code = <32>;
};
- serial@13810000 {
- status = "okay";
+ key_E {
+ keypad,row = <0>;
+ keypad,column = <7>;
+ linux,code = <18>;
};
+};
+
+&mfc {
+ samsung,mfc-r = <0x43000000 0x800000>;
+ samsung,mfc-l = <0x51000000 0x800000>;
+ status = "okay";
+};
- serial@13820000 {
- status = "okay";
+&pinctrl_1 {
+ keypad_rows: keypad-rows {
+ samsung,pins = "gpx2-0", "gpx2-1", "gpx2-2";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
};
- serial@13830000 {
- status = "okay";
+ keypad_cols: keypad-cols {
+ samsung,pins = "gpx1-0", "gpx1-1", "gpx1-2", "gpx1-3",
+ "gpx1-4", "gpx1-5", "gpx1-6", "gpx1-7";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
};
+};
- fixed-rate-clocks {
- xxti {
- compatible = "samsung,clock-xxti";
- clock-frequency = <0>;
- };
+&sdhci_2 {
+ bus-width = <4>;
+ pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &sd2_cd>;
+ pinctrl-names = "default";
+ status = "okay";
+};
- xusbxti {
- compatible = "samsung,clock-xusbxti";
- clock-frequency = <24000000>;
- };
- };
+&serial_0 {
+ status = "okay";
+};
+
+&serial_1 {
+ status = "okay";
+};
+
+&serial_2 {
+ status = "okay";
+};
+
+&serial_3 {
+ status = "okay";
};
--
2.1.0
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v3 11/11] ARM: dts: exynos4: Use labels for overriding nodes in Trats2
2015-04-17 13:47 [PATCH v3 00/11] ARM: dts: exynos4: labels for overriding nodes Krzysztof Kozlowski
` (9 preceding siblings ...)
2015-04-17 13:47 ` [PATCH v3 10/11] ARM: dts: exynos4: Use labels for overriding nodes in SMDK4412 Krzysztof Kozlowski
@ 2015-04-17 13:47 ` Krzysztof Kozlowski
10 siblings, 0 replies; 12+ messages in thread
From: Krzysztof Kozlowski @ 2015-04-17 13:47 UTC (permalink / raw)
To: Kukjin Kim, devicetree, linux-arm-kernel, linux-samsung-soc,
linux-kernel
Cc: Arnd Bergmann, Olof Johansson, Krzysztof Kozlowski
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
---
arch/arm/boot/dts/exynos4412-trats2.dts | 1331 ++++++++++++++++---------------
1 file changed, 666 insertions(+), 665 deletions(-)
diff --git a/arch/arm/boot/dts/exynos4412-trats2.dts b/arch/arm/boot/dts/exynos4412-trats2.dts
index 173ffa479ad3..e83929c2dc90 100644
--- a/arch/arm/boot/dts/exynos4412-trats2.dts
+++ b/arch/arm/boot/dts/exynos4412-trats2.dts
@@ -130,411 +130,6 @@
};
};
- adc: adc@126C0000 {
- vdd-supply = <&ldo3_reg>;
- status = "okay";
- };
-
- i2c@13890000 {
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-slave-addr = <0x10>;
- samsung,i2c-max-bus-freq = <400000>;
- pinctrl-0 = <&i2c3_bus>;
- pinctrl-names = "default";
- status = "okay";
-
- mms114-touchscreen@48 {
- compatible = "melfas,mms114";
- reg = <0x48>;
- interrupt-parent = <&gpm2>;
- interrupts = <3 2>;
- x-size = <720>;
- y-size = <1280>;
- avdd-supply = <&ldo23_reg>;
- vdd-supply = <&ldo24_reg>;
- };
- };
-
- i2c_0: i2c@13860000 {
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-slave-addr = <0x10>;
- samsung,i2c-max-bus-freq = <400000>;
- pinctrl-0 = <&i2c0_bus>;
- pinctrl-names = "default";
- status = "okay";
-
- s5c73m3@3c {
- compatible = "samsung,s5c73m3";
- reg = <0x3c>;
- standby-gpios = <&gpm0 1 1>; /* ISP_STANDBY */
- xshutdown-gpios = <&gpf1 3 1>; /* ISP_RESET */
- vdd-int-supply = <&buck9_reg>;
- vddio-cis-supply = <&ldo9_reg>;
- vdda-supply = <&ldo17_reg>;
- vddio-host-supply = <&ldo18_reg>;
- vdd-af-supply = <&cam_af_reg>;
- vdd-reg-supply = <&cam_io_reg>;
- clock-frequency = <24000000>;
- /* CAM_A_CLKOUT */
- clocks = <&camera 0>;
- clock-names = "cis_extclk";
- port {
- s5c73m3_ep: endpoint {
- remote-endpoint = <&csis0_ep>;
- data-lanes = <1 2 3 4>;
- };
- };
- };
- };
-
- i2c@138A0000 {
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-slave-addr = <0x10>;
- samsung,i2c-max-bus-freq = <100000>;
- pinctrl-0 = <&i2c4_bus>;
- pinctrl-names = "default";
- status = "okay";
-
- wm1811: wm1811@1a {
- compatible = "wlf,wm1811";
- reg = <0x1a>;
- clocks = <&pmu_system_controller 0>;
- clock-names = "MCLK1";
- DCVDD-supply = <&ldo3_reg>;
- DBVDD1-supply = <&ldo3_reg>;
- wlf,ldo1ena = <&gpj0 4 0>;
- };
- };
-
- i2c@138D0000 {
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-slave-addr = <0x10>;
- samsung,i2c-max-bus-freq = <100000>;
- pinctrl-0 = <&i2c7_bus>;
- pinctrl-names = "default";
- status = "okay";
-
- max77686_pmic@09 {
- compatible = "maxim,max77686";
- interrupt-parent = <&gpx0>;
- interrupts = <7 0>;
- reg = <0x09>;
- #clock-cells = <1>;
-
- voltage-regulators {
- ldo1_reg: ldo1 {
- regulator-compatible = "LDO1";
- regulator-name = "VALIVE_1.0V_AP";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- };
-
- ldo2_reg: ldo2 {
- regulator-compatible = "LDO2";
- regulator-name = "VM1M2_1.2V_AP";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-always-on;
- regulator-state-mem {
- regulator-on-in-suspend;
- };
- };
-
- ldo3_reg: ldo3 {
- regulator-compatible = "LDO3";
- regulator-name = "VCC_1.8V_AP";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- ldo4_reg: ldo4 {
- regulator-compatible = "LDO4";
- regulator-name = "VCC_2.8V_AP";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- regulator-always-on;
- };
-
- ldo5_reg: ldo5 {
- regulator-compatible = "LDO5";
- regulator-name = "VCC_1.8V_IO";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- ldo6_reg: ldo6 {
- regulator-compatible = "LDO6";
- regulator-name = "VMPLL_1.0V_AP";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- regulator-state-mem {
- regulator-on-in-suspend;
- };
- };
-
- ldo7_reg: ldo7 {
- regulator-compatible = "LDO7";
- regulator-name = "VPLL_1.0V_AP";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- regulator-state-mem {
- regulator-on-in-suspend;
- };
- };
-
- ldo8_reg: ldo8 {
- regulator-compatible = "LDO8";
- regulator-name = "VMIPI_1.0V";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- ldo9_reg: ldo9 {
- regulator-compatible = "LDO9";
- regulator-name = "CAM_ISP_MIPI_1.2V";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- ldo10_reg: ldo10 {
- regulator-compatible = "LDO10";
- regulator-name = "VMIPI_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- ldo11_reg: ldo11 {
- regulator-compatible = "LDO11";
- regulator-name = "VABB1_1.95V";
- regulator-min-microvolt = <1950000>;
- regulator-max-microvolt = <1950000>;
- regulator-always-on;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- ldo12_reg: ldo12 {
- regulator-compatible = "LDO12";
- regulator-name = "VUOTG_3.0V";
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- ldo13_reg: ldo13 {
- regulator-compatible = "LDO13";
- regulator-name = "NFC_AVDD_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo14_reg: ldo14 {
- regulator-compatible = "LDO14";
- regulator-name = "VABB2_1.95V";
- regulator-min-microvolt = <1950000>;
- regulator-max-microvolt = <1950000>;
- regulator-always-on;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- ldo15_reg: ldo15 {
- regulator-compatible = "LDO15";
- regulator-name = "VHSIC_1.0V";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-state-mem {
- regulator-on-in-suspend;
- };
- };
-
- ldo16_reg: ldo16 {
- regulator-compatible = "LDO16";
- regulator-name = "VHSIC_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-state-mem {
- regulator-on-in-suspend;
- };
- };
-
- ldo17_reg: ldo17 {
- regulator-compatible = "LDO17";
- regulator-name = "CAM_SENSOR_CORE_1.2V";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- ldo18_reg: ldo18 {
- regulator-compatible = "LDO18";
- regulator-name = "CAM_ISP_SEN_IO_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo19_reg: ldo19 {
- regulator-compatible = "LDO19";
- regulator-name = "VT_CAM_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo20_reg: ldo20 {
- regulator-compatible = "LDO20";
- regulator-name = "VDDQ_PRE_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo21_reg: ldo21 {
- regulator-compatible = "LDO21";
- regulator-name = "VTF_2.8V";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- maxim,ena-gpios = <&gpy2 0 GPIO_ACTIVE_HIGH>;
- };
-
- ldo22_reg: ldo22 {
- regulator-compatible = "LDO22";
- regulator-name = "VMEM_VDD_2.8V";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- maxim,ena-gpios = <&gpk0 2 GPIO_ACTIVE_HIGH>;
- };
-
- ldo23_reg: ldo23 {
- regulator-compatible = "LDO23";
- regulator-name = "TSP_AVDD_3.3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- ldo24_reg: ldo24 {
- regulator-compatible = "LDO24";
- regulator-name = "TSP_VDD_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo25_reg: ldo25 {
- regulator-compatible = "LDO25";
- regulator-name = "LCD_VCC_3.3V";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- };
-
- ldo26_reg: ldo26 {
- regulator-compatible = "LDO26";
- regulator-name = "MOTOR_VCC_3.0V";
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- };
-
- buck1_reg: buck1 {
- regulator-compatible = "BUCK1";
- regulator-name = "vdd_mif";
- regulator-min-microvolt = <850000>;
- regulator-max-microvolt = <1100000>;
- regulator-always-on;
- regulator-boot-on;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- buck2_reg: buck2 {
- regulator-compatible = "BUCK2";
- regulator-name = "vdd_arm";
- regulator-min-microvolt = <850000>;
- regulator-max-microvolt = <1500000>;
- regulator-always-on;
- regulator-boot-on;
- regulator-state-mem {
- regulator-on-in-suspend;
- };
- };
-
- buck3_reg: buck3 {
- regulator-compatible = "BUCK3";
- regulator-name = "vdd_int";
- regulator-min-microvolt = <850000>;
- regulator-max-microvolt = <1150000>;
- regulator-always-on;
- regulator-boot-on;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- buck4_reg: buck4 {
- regulator-compatible = "BUCK4";
- regulator-name = "vdd_g3d";
- regulator-min-microvolt = <850000>;
- regulator-max-microvolt = <1150000>;
- regulator-boot-on;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- buck5_reg: buck5 {
- regulator-compatible = "BUCK5";
- regulator-name = "VMEM_1.2V_AP";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-always-on;
- };
-
- buck6_reg: buck6 {
- regulator-compatible = "BUCK6";
- regulator-name = "VCC_SUB_1.35V";
- regulator-min-microvolt = <1350000>;
- regulator-max-microvolt = <1350000>;
- regulator-always-on;
- };
-
- buck7_reg: buck7 {
- regulator-compatible = "BUCK7";
- regulator-name = "VCC_SUB_2.0V";
- regulator-min-microvolt = <2000000>;
- regulator-max-microvolt = <2000000>;
- regulator-always-on;
- };
-
- buck8_reg: buck8 {
- regulator-compatible = "BUCK8";
- regulator-name = "VMEM_VDDF_3.0V";
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
- maxim,ena-gpios = <&gpk0 2 GPIO_ACTIVE_HIGH>;
- };
-
- buck9_reg: buck9 {
- regulator-compatible = "BUCK9";
- regulator-name = "CAM_ISP_CORE_1.2V";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1200000>;
- maxim,ena-gpios = <&gpm0 3 GPIO_ACTIVE_HIGH>;
- };
- };
- };
- };
-
i2c_max77693: i2c-gpio-1 {
compatible = "i2c-gpio";
gpios = <&gpm2 0 GPIO_ACTIVE_HIGH>, <&gpm2 1 GPIO_ACTIVE_HIGH>;
@@ -597,54 +192,6 @@
};
};
- mmc@12550000 {
- num-slots = <1>;
- broken-cd;
- non-removable;
- card-detect-delay = <200>;
- vmmc-supply = <&ldo22_reg>;
- clock-frequency = <400000000>;
- samsung,dw-mshc-ciu-div = <0>;
- samsung,dw-mshc-sdr-timing = <2 3>;
- samsung,dw-mshc-ddr-timing = <1 2>;
- pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>;
- pinctrl-names = "default";
- status = "okay";
- bus-width = <8>;
- cap-mmc-highspeed;
- };
-
- sdhci@12530000 {
- bus-width = <4>;
- cd-gpios = <&gpx3 4 0>;
- cd-inverted;
- pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4>;
- pinctrl-names = "default";
- vmmc-supply = <&ldo21_reg>;
- status = "okay";
- };
-
- serial@13800000 {
- status = "okay";
- };
-
- serial@13810000 {
- status = "okay";
- };
-
- serial@13820000 {
- status = "okay";
- };
-
- serial@13830000 {
- status = "okay";
- };
-
- tmu@100C0000 {
- vtmu-supply = <&ldo10_reg>;
- status = "okay";
- };
-
i2c_ak8975: i2c-gpio-0 {
compatible = "i2c-gpio";
gpios = <&gpy2 4 0>, <&gpy2 5 0>;
@@ -676,90 +223,6 @@
};
};
- spi_1: spi@13930000 {
- pinctrl-names = "default";
- pinctrl-0 = <&spi1_bus>;
- cs-gpios = <&gpb 5 0>;
- status = "okay";
-
- s5c73m3_spi: s5c73m3 {
- compatible = "samsung,s5c73m3";
- spi-max-frequency = <50000000>;
- reg = <0>;
- controller-data {
- samsung,spi-feedback-delay = <2>;
- };
- };
- };
-
- pwm: pwm@139D0000 {
- pinctrl-0 = <&pwm0_out>;
- pinctrl-names = "default";
- samsung,pwm-outputs = <0>;
- status = "okay";
- };
-
- dsi_0: dsi@11C80000 {
- vddcore-supply = <&ldo8_reg>;
- vddio-supply = <&ldo10_reg>;
- samsung,pll-clock-frequency = <24000000>;
- status = "okay";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@1 {
- reg = <1>;
-
- dsi_out: endpoint {
- remote-endpoint = <&dsi_in>;
- samsung,burst-clock-frequency = <500000000>;
- samsung,esc-clock-frequency = <20000000>;
- };
- };
- };
-
- panel@0 {
- compatible = "samsung,s6e8aa0";
- reg = <0>;
- vdd3-supply = <&lcd_vdd3_reg>;
- vci-supply = <&ldo25_reg>;
- reset-gpios = <&gpy4 5 0>;
- power-on-delay= <50>;
- reset-delay = <100>;
- init-delay = <100>;
- flip-horizontal;
- flip-vertical;
- panel-width-mm = <58>;
- panel-height-mm = <103>;
-
- display-timings {
- timing-0 {
- clock-frequency = <0>;
- hactive = <720>;
- vactive = <1280>;
- hfront-porch = <5>;
- hback-porch = <5>;
- hsync-len = <5>;
- vfront-porch = <13>;
- vback-porch = <1>;
- vsync-len = <2>;
- };
- };
-
- port {
- dsi_in: endpoint {
- remote-endpoint = <&dsi_out>;
- };
- };
- };
- };
-
- fimd@11c00000 {
- status = "okay";
- };
-
camera: camera {
pinctrl-0 = <&cam_port_a_clk_active &cam_port_b_clk_active>;
pinctrl-names = "default";
@@ -769,124 +232,7 @@
assigned-clock-parents = <&clock CLK_XUSBXTI>,
<&clock CLK_XUSBXTI>;
- fimc_0: fimc@11800000 {
- status = "okay";
- assigned-clocks = <&clock CLK_MOUT_FIMC0>,
- <&clock CLK_SCLK_FIMC0>;
- assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
- assigned-clock-rates = <0>, <176000000>;
- };
-
- fimc_1: fimc@11810000 {
- status = "okay";
- assigned-clocks = <&clock CLK_MOUT_FIMC1>,
- <&clock CLK_SCLK_FIMC1>;
- assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
- assigned-clock-rates = <0>, <176000000>;
- };
-
- fimc_2: fimc@11820000 {
- status = "okay";
- assigned-clocks = <&clock CLK_MOUT_FIMC2>,
- <&clock CLK_SCLK_FIMC2>;
- assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
- assigned-clock-rates = <0>, <176000000>;
- };
-
- fimc_3: fimc@11830000 {
- status = "okay";
- assigned-clocks = <&clock CLK_MOUT_FIMC3>,
- <&clock CLK_SCLK_FIMC3>;
- assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
- assigned-clock-rates = <0>, <176000000>;
- };
-
- csis_0: csis@11880000 {
- status = "okay";
- vddcore-supply = <&ldo8_reg>;
- vddio-supply = <&ldo10_reg>;
- assigned-clocks = <&clock CLK_MOUT_CSIS0>,
- <&clock CLK_SCLK_CSIS0>;
- assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
- assigned-clock-rates = <0>, <176000000>;
-
- /* Camera C (3) MIPI CSI-2 (CSIS0) */
- port@3 {
- reg = <3>;
- csis0_ep: endpoint {
- remote-endpoint = <&s5c73m3_ep>;
- data-lanes = <1 2 3 4>;
- samsung,csis-hs-settle = <12>;
- };
- };
- };
-
- csis_1: csis@11890000 {
- status = "okay";
- vddcore-supply = <&ldo8_reg>;
- vddio-supply = <&ldo10_reg>;
- assigned-clocks = <&clock CLK_MOUT_CSIS1>,
- <&clock CLK_SCLK_CSIS1>;
- assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
- assigned-clock-rates = <0>, <176000000>;
-
- /* Camera D (4) MIPI CSI-2 (CSIS1) */
- port@4 {
- reg = <4>;
- csis1_ep: endpoint {
- remote-endpoint = <&is_s5k6a3_ep>;
- data-lanes = <1>;
- samsung,csis-hs-settle = <18>;
- samsung,csis-wclk;
- };
- };
- };
-
- fimc_lite_0: fimc-lite@12390000 {
- status = "okay";
- };
- fimc_lite_1: fimc-lite@123A0000 {
- status = "okay";
- };
-
- fimc-is@12000000 {
- pinctrl-0 = <&fimc_is_uart>;
- pinctrl-names = "default";
- status = "okay";
-
- i2c1_isp: i2c-isp@12140000 {
- pinctrl-0 = <&fimc_is_i2c1>;
- pinctrl-names = "default";
-
- s5k6a3@10 {
- compatible = "samsung,s5k6a3";
- reg = <0x10>;
- svdda-supply = <&cam_io_reg>;
- svddio-supply = <&ldo19_reg>;
- afvdd-supply = <&ldo19_reg>;
- clock-frequency = <24000000>;
- /* CAM_B_CLKOUT */
- clocks = <&camera 1>;
- clock-names = "extclk";
- samsung,camclk-out = <1>;
- gpios = <&gpm1 6 0>;
-
- port {
- is_s5k6a3_ep: endpoint {
- remote-endpoint = <&csis1_ep>;
- data-lanes = <1>;
- };
- };
- };
- };
- };
- };
-
- i2s0: i2s@03830000 {
- pinctrl-0 = <&i2s0_bus>;
- pinctrl-names = "default";
- status = "okay";
};
sound {
@@ -901,17 +247,6 @@
"SPK", "SPKOUTRP";
};
- exynos-usbphy@125B0000 {
- status = "okay";
- };
-
- hsotg@12480000 {
- vusb_d-supply = <&ldo15_reg>;
- vusb_a-supply = <&ldo12_reg>;
- dr_mode = "peripheral";
- status = "okay";
- };
-
thermistor-ap@0 {
compatible = "ntc,ncp15wb473";
pullup-uv = <1800000>; /* VCC_1.8V_AP */
@@ -944,6 +279,619 @@
};
};
+&adc {
+ vdd-supply = <&ldo3_reg>;
+ status = "okay";
+};
+
+&csis_0 {
+ status = "okay";
+ vddcore-supply = <&ldo8_reg>;
+ vddio-supply = <&ldo10_reg>;
+ assigned-clocks = <&clock CLK_MOUT_CSIS0>,
+ <&clock CLK_SCLK_CSIS0>;
+ assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
+ assigned-clock-rates = <0>, <176000000>;
+
+ /* Camera C (3) MIPI CSI-2 (CSIS0) */
+ port@3 {
+ reg = <3>;
+ csis0_ep: endpoint {
+ remote-endpoint = <&s5c73m3_ep>;
+ data-lanes = <1 2 3 4>;
+ samsung,csis-hs-settle = <12>;
+ };
+ };
+};
+
+&csis_1 {
+ status = "okay";
+ vddcore-supply = <&ldo8_reg>;
+ vddio-supply = <&ldo10_reg>;
+ assigned-clocks = <&clock CLK_MOUT_CSIS1>,
+ <&clock CLK_SCLK_CSIS1>;
+ assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
+ assigned-clock-rates = <0>, <176000000>;
+
+ /* Camera D (4) MIPI CSI-2 (CSIS1) */
+ port@4 {
+ reg = <4>;
+ csis1_ep: endpoint {
+ remote-endpoint = <&is_s5k6a3_ep>;
+ data-lanes = <1>;
+ samsung,csis-hs-settle = <18>;
+ samsung,csis-wclk;
+ };
+ };
+};
+
+&dsi_0 {
+ vddcore-supply = <&ldo8_reg>;
+ vddio-supply = <&ldo10_reg>;
+ samsung,pll-clock-frequency = <24000000>;
+ status = "okay";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@1 {
+ reg = <1>;
+
+ dsi_out: endpoint {
+ remote-endpoint = <&dsi_in>;
+ samsung,burst-clock-frequency = <500000000>;
+ samsung,esc-clock-frequency = <20000000>;
+ };
+ };
+ };
+
+ panel@0 {
+ compatible = "samsung,s6e8aa0";
+ reg = <0>;
+ vdd3-supply = <&lcd_vdd3_reg>;
+ vci-supply = <&ldo25_reg>;
+ reset-gpios = <&gpy4 5 0>;
+ power-on-delay= <50>;
+ reset-delay = <100>;
+ init-delay = <100>;
+ flip-horizontal;
+ flip-vertical;
+ panel-width-mm = <58>;
+ panel-height-mm = <103>;
+
+ display-timings {
+ timing-0 {
+ clock-frequency = <0>;
+ hactive = <720>;
+ vactive = <1280>;
+ hfront-porch = <5>;
+ hback-porch = <5>;
+ hsync-len = <5>;
+ vfront-porch = <13>;
+ vback-porch = <1>;
+ vsync-len = <2>;
+ };
+ };
+
+ port {
+ dsi_in: endpoint {
+ remote-endpoint = <&dsi_out>;
+ };
+ };
+ };
+};
+
+&exynos_usbphy {
+ status = "okay";
+};
+
+&fimc_0 {
+ status = "okay";
+ assigned-clocks = <&clock CLK_MOUT_FIMC0>,
+ <&clock CLK_SCLK_FIMC0>;
+ assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
+ assigned-clock-rates = <0>, <176000000>;
+};
+
+&fimc_1 {
+ status = "okay";
+ assigned-clocks = <&clock CLK_MOUT_FIMC1>,
+ <&clock CLK_SCLK_FIMC1>;
+ assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
+ assigned-clock-rates = <0>, <176000000>;
+};
+
+&fimc_2 {
+ status = "okay";
+ assigned-clocks = <&clock CLK_MOUT_FIMC2>,
+ <&clock CLK_SCLK_FIMC2>;
+ assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
+ assigned-clock-rates = <0>, <176000000>;
+};
+
+&fimc_3 {
+ status = "okay";
+ assigned-clocks = <&clock CLK_MOUT_FIMC3>,
+ <&clock CLK_SCLK_FIMC3>;
+ assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
+ assigned-clock-rates = <0>, <176000000>;
+};
+
+&fimc_is {
+ pinctrl-0 = <&fimc_is_uart>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ i2c1_isp: i2c-isp@12140000 {
+ pinctrl-0 = <&fimc_is_i2c1>;
+ pinctrl-names = "default";
+
+ s5k6a3@10 {
+ compatible = "samsung,s5k6a3";
+ reg = <0x10>;
+ svdda-supply = <&cam_io_reg>;
+ svddio-supply = <&ldo19_reg>;
+ afvdd-supply = <&ldo19_reg>;
+ clock-frequency = <24000000>;
+ /* CAM_B_CLKOUT */
+ clocks = <&camera 1>;
+ clock-names = "extclk";
+ samsung,camclk-out = <1>;
+ gpios = <&gpm1 6 0>;
+
+ port {
+ is_s5k6a3_ep: endpoint {
+ remote-endpoint = <&csis1_ep>;
+ data-lanes = <1>;
+ };
+ };
+ };
+ };
+};
+
+&fimc_lite_0 {
+ status = "okay";
+};
+
+&fimc_lite_1 {
+ status = "okay";
+};
+
+&fimd {
+ status = "okay";
+};
+
+&hsotg {
+ vusb_d-supply = <&ldo15_reg>;
+ vusb_a-supply = <&ldo12_reg>;
+ dr_mode = "peripheral";
+ status = "okay";
+};
+
+&i2c_0 {
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-slave-addr = <0x10>;
+ samsung,i2c-max-bus-freq = <400000>;
+ pinctrl-0 = <&i2c0_bus>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ s5c73m3@3c {
+ compatible = "samsung,s5c73m3";
+ reg = <0x3c>;
+ standby-gpios = <&gpm0 1 1>; /* ISP_STANDBY */
+ xshutdown-gpios = <&gpf1 3 1>; /* ISP_RESET */
+ vdd-int-supply = <&buck9_reg>;
+ vddio-cis-supply = <&ldo9_reg>;
+ vdda-supply = <&ldo17_reg>;
+ vddio-host-supply = <&ldo18_reg>;
+ vdd-af-supply = <&cam_af_reg>;
+ vdd-reg-supply = <&cam_io_reg>;
+ clock-frequency = <24000000>;
+ /* CAM_A_CLKOUT */
+ clocks = <&camera 0>;
+ clock-names = "cis_extclk";
+ port {
+ s5c73m3_ep: endpoint {
+ remote-endpoint = <&csis0_ep>;
+ data-lanes = <1 2 3 4>;
+ };
+ };
+ };
+};
+
+&i2c_3 {
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-slave-addr = <0x10>;
+ samsung,i2c-max-bus-freq = <400000>;
+ pinctrl-0 = <&i2c3_bus>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ mms114-touchscreen@48 {
+ compatible = "melfas,mms114";
+ reg = <0x48>;
+ interrupt-parent = <&gpm2>;
+ interrupts = <3 2>;
+ x-size = <720>;
+ y-size = <1280>;
+ avdd-supply = <&ldo23_reg>;
+ vdd-supply = <&ldo24_reg>;
+ };
+};
+
+&i2c_4 {
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-slave-addr = <0x10>;
+ samsung,i2c-max-bus-freq = <100000>;
+ pinctrl-0 = <&i2c4_bus>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ wm1811: wm1811@1a {
+ compatible = "wlf,wm1811";
+ reg = <0x1a>;
+ clocks = <&pmu_system_controller 0>;
+ clock-names = "MCLK1";
+ DCVDD-supply = <&ldo3_reg>;
+ DBVDD1-supply = <&ldo3_reg>;
+ wlf,ldo1ena = <&gpj0 4 0>;
+ };
+};
+
+&i2c_7 {
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-slave-addr = <0x10>;
+ samsung,i2c-max-bus-freq = <100000>;
+ pinctrl-0 = <&i2c7_bus>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ max77686_pmic@09 {
+ compatible = "maxim,max77686";
+ interrupt-parent = <&gpx0>;
+ interrupts = <7 0>;
+ reg = <0x09>;
+ #clock-cells = <1>;
+
+ voltage-regulators {
+ ldo1_reg: ldo1 {
+ regulator-compatible = "LDO1";
+ regulator-name = "VALIVE_1.0V_AP";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
+
+ ldo2_reg: ldo2 {
+ regulator-compatible = "LDO2";
+ regulator-name = "VM1M2_1.2V_AP";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ ldo3_reg: ldo3 {
+ regulator-compatible = "LDO3";
+ regulator-name = "VCC_1.8V_AP";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo4_reg: ldo4 {
+ regulator-compatible = "LDO4";
+ regulator-name = "VCC_2.8V_AP";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ };
+
+ ldo5_reg: ldo5 {
+ regulator-compatible = "LDO5";
+ regulator-name = "VCC_1.8V_IO";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo6_reg: ldo6 {
+ regulator-compatible = "LDO6";
+ regulator-name = "VMPLL_1.0V_AP";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ ldo7_reg: ldo7 {
+ regulator-compatible = "LDO7";
+ regulator-name = "VPLL_1.0V_AP";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ ldo8_reg: ldo8 {
+ regulator-compatible = "LDO8";
+ regulator-name = "VMIPI_1.0V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo9_reg: ldo9 {
+ regulator-compatible = "LDO9";
+ regulator-name = "CAM_ISP_MIPI_1.2V";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ ldo10_reg: ldo10 {
+ regulator-compatible = "LDO10";
+ regulator-name = "VMIPI_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo11_reg: ldo11 {
+ regulator-compatible = "LDO11";
+ regulator-name = "VABB1_1.95V";
+ regulator-min-microvolt = <1950000>;
+ regulator-max-microvolt = <1950000>;
+ regulator-always-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo12_reg: ldo12 {
+ regulator-compatible = "LDO12";
+ regulator-name = "VUOTG_3.0V";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo13_reg: ldo13 {
+ regulator-compatible = "LDO13";
+ regulator-name = "NFC_AVDD_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo14_reg: ldo14 {
+ regulator-compatible = "LDO14";
+ regulator-name = "VABB2_1.95V";
+ regulator-min-microvolt = <1950000>;
+ regulator-max-microvolt = <1950000>;
+ regulator-always-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo15_reg: ldo15 {
+ regulator-compatible = "LDO15";
+ regulator-name = "VHSIC_1.0V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ ldo16_reg: ldo16 {
+ regulator-compatible = "LDO16";
+ regulator-name = "VHSIC_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ ldo17_reg: ldo17 {
+ regulator-compatible = "LDO17";
+ regulator-name = "CAM_SENSOR_CORE_1.2V";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ ldo18_reg: ldo18 {
+ regulator-compatible = "LDO18";
+ regulator-name = "CAM_ISP_SEN_IO_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo19_reg: ldo19 {
+ regulator-compatible = "LDO19";
+ regulator-name = "VT_CAM_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo20_reg: ldo20 {
+ regulator-compatible = "LDO20";
+ regulator-name = "VDDQ_PRE_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo21_reg: ldo21 {
+ regulator-compatible = "LDO21";
+ regulator-name = "VTF_2.8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ maxim,ena-gpios = <&gpy2 0 GPIO_ACTIVE_HIGH>;
+ };
+
+ ldo22_reg: ldo22 {
+ regulator-compatible = "LDO22";
+ regulator-name = "VMEM_VDD_2.8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ maxim,ena-gpios = <&gpk0 2 GPIO_ACTIVE_HIGH>;
+ };
+
+ ldo23_reg: ldo23 {
+ regulator-compatible = "LDO23";
+ regulator-name = "TSP_AVDD_3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldo24_reg: ldo24 {
+ regulator-compatible = "LDO24";
+ regulator-name = "TSP_VDD_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo25_reg: ldo25 {
+ regulator-compatible = "LDO25";
+ regulator-name = "LCD_VCC_3.3V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ ldo26_reg: ldo26 {
+ regulator-compatible = "LDO26";
+ regulator-name = "MOTOR_VCC_3.0V";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ buck1_reg: buck1 {
+ regulator-compatible = "BUCK1";
+ regulator-name = "vdd_mif";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ buck2_reg: buck2 {
+ regulator-compatible = "BUCK2";
+ regulator-name = "vdd_arm";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ buck3_reg: buck3 {
+ regulator-compatible = "BUCK3";
+ regulator-name = "vdd_int";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1150000>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ buck4_reg: buck4 {
+ regulator-compatible = "BUCK4";
+ regulator-name = "vdd_g3d";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1150000>;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ buck5_reg: buck5 {
+ regulator-compatible = "BUCK5";
+ regulator-name = "VMEM_1.2V_AP";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ };
+
+ buck6_reg: buck6 {
+ regulator-compatible = "BUCK6";
+ regulator-name = "VCC_SUB_1.35V";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ };
+
+ buck7_reg: buck7 {
+ regulator-compatible = "BUCK7";
+ regulator-name = "VCC_SUB_2.0V";
+ regulator-min-microvolt = <2000000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-always-on;
+ };
+
+ buck8_reg: buck8 {
+ regulator-compatible = "BUCK8";
+ regulator-name = "VMEM_VDDF_3.0V";
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ maxim,ena-gpios = <&gpk0 2 GPIO_ACTIVE_HIGH>;
+ };
+
+ buck9_reg: buck9 {
+ regulator-compatible = "BUCK9";
+ regulator-name = "CAM_ISP_CORE_1.2V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1200000>;
+ maxim,ena-gpios = <&gpm0 3 GPIO_ACTIVE_HIGH>;
+ };
+ };
+ };
+};
+
+&i2s0 {
+ pinctrl-0 = <&i2s0_bus>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&mshc_0 {
+ num-slots = <1>;
+ broken-cd;
+ non-removable;
+ card-detect-delay = <200>;
+ vmmc-supply = <&ldo22_reg>;
+ clock-frequency = <400000000>;
+ samsung,dw-mshc-ciu-div = <0>;
+ samsung,dw-mshc-sdr-timing = <2 3>;
+ samsung,dw-mshc-ddr-timing = <1 2>;
+ pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>;
+ pinctrl-names = "default";
+ status = "okay";
+ bus-width = <8>;
+ cap-mmc-highspeed;
+};
+
&pmu_system_controller {
assigned-clocks = <&pmu_system_controller 0>;
assigned-clock-parents = <&clock CLK_XUSBXTI>;
@@ -1304,3 +1252,56 @@
PIN_SLP(gpv4-0, INPUT, DOWN);
};
};
+
+&pwm {
+ pinctrl-0 = <&pwm0_out>;
+ pinctrl-names = "default";
+ samsung,pwm-outputs = <0>;
+ status = "okay";
+};
+
+&sdhci_2 {
+ bus-width = <4>;
+ cd-gpios = <&gpx3 4 0>;
+ cd-inverted;
+ pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4>;
+ pinctrl-names = "default";
+ vmmc-supply = <&ldo21_reg>;
+ status = "okay";
+};
+
+&serial_0 {
+ status = "okay";
+};
+
+&serial_1 {
+ status = "okay";
+};
+
+&serial_2 {
+ status = "okay";
+};
+
+&serial_3 {
+ status = "okay";
+};
+&spi_1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi1_bus>;
+ cs-gpios = <&gpb 5 0>;
+ status = "okay";
+
+ s5c73m3_spi: s5c73m3 {
+ compatible = "samsung,s5c73m3";
+ spi-max-frequency = <50000000>;
+ reg = <0>;
+ controller-data {
+ samsung,spi-feedback-delay = <2>;
+ };
+ };
+};
+
+&tmu {
+ vtmu-supply = <&ldo10_reg>;
+ status = "okay";
+};
--
2.1.0
^ permalink raw reply related [flat|nested] 12+ messages in thread