From mboxrd@z Thu Jan 1 00:00:00 1970 From: Jacek Anaszewski Subject: [PATCH v10 4/8] DT: aat1290: Document handling external strobe sources Date: Mon, 08 Jun 2015 11:02:21 +0200 Message-ID: <1433754145-12765-5-git-send-email-j.anaszewski@samsung.com> References: <1433754145-12765-1-git-send-email-j.anaszewski@samsung.com> Return-path: In-reply-to: <1433754145-12765-1-git-send-email-j.anaszewski@samsung.com> Sender: linux-media-owner@vger.kernel.org To: linux-leds@vger.kernel.org, linux-media@vger.kernel.org Cc: kyungmin.park@samsung.com, pavel@ucw.cz, cooloney@gmail.com, rpurdie@rpsys.net, sakari.ailus@iki.fi, s.nawrocki@samsung.com, Jacek Anaszewski , devicetree@vger.kernel.org List-Id: devicetree@vger.kernel.org This patch adds documentation for a pinctrl-names property. The property, when present, is used for switching the source of the strobe signal for the device. Signed-off-by: Jacek Anaszewski Acked-by: Kyungmin Park Cc: Bryan Wu Cc: Richard Purdie Cc: Sakari Ailus Cc: devicetree@vger.kernel.org --- .../devicetree/bindings/leds/leds-aat1290.txt | 36 ++++++++++++++++++-- 1 file changed, 34 insertions(+), 2 deletions(-) diff --git a/Documentation/devicetree/bindings/leds/leds-aat1290.txt b/Documentation/devicetree/bindings/leds/leds-aat1290.txt index ef88b9c..c05ed91 100644 --- a/Documentation/devicetree/bindings/leds/leds-aat1290.txt +++ b/Documentation/devicetree/bindings/leds/leds-aat1290.txt @@ -2,7 +2,9 @@ The device is controlled through two pins: FL_EN and EN_SET. The pins when, asserted high, enable flash strobe and movie mode (max 1/2 of flash current) -respectively. +respectively. In order to add a capability of selecting the strobe signal source +(e.g. CPU or camera sensor) there is an additional switch required, independent +of the flash chip. The switch is controlled with pin control. Required properties: @@ -10,6 +12,13 @@ Required properties: - flen-gpios : Must be device tree identifier of the flash device FL_EN pin. - enset-gpios : Must be device tree identifier of the flash device EN_SET pin. +Optional properties: +- pinctrl-names : Must contain entries: "default", "host", "isp". Entries + "default" and "host" must refer to the same pin configuration + node, which sets the host as a strobe signal provider. Entry + "isp" must refer to the pin configuration node, which sets the + ISP as a strobe signal provider. + A discrete LED element connected to the device must be represented by a child node - see Documentation/devicetree/bindings/leds/common.txt. @@ -25,13 +34,22 @@ Required properties of the LED child node: Optional properties of the LED child node: - label : see Documentation/devicetree/bindings/leds/common.txt -Example (by Ct = 220nF, Rset = 160kohm): +Example (by Ct = 220nF, Rset = 160kohm and exynos4412-trats2 board with +a switch that allows for routing strobe signal either from the host or from +the camera sensor): + +#include "exynos4412.dtsi" aat1290 { compatible = "skyworks,aat1290"; flen-gpios = <&gpj1 1 GPIO_ACTIVE_HIGH>; enset-gpios = <&gpj1 2 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default", "host", "isp"; + pinctrl-0 = <&camera_flash_host>; + pinctrl-1 = <&camera_flash_host>; + pinctrl-2 = <&camera_flash_isp>; + camera_flash: flash-led { label = "aat1290-flash"; led-max-microamp = <520833>; @@ -39,3 +57,17 @@ aat1290 { flash-timeout-us = <1940000>; }; }; + +&pinctrl_0 { + camera_flash_host: camera-flash-host { + samsung,pins = "gpj1-0"; + samsung,pin-function = <1>; + samsung,pin-val = <0>; + }; + + camera_flash_isp: camera-flash-isp { + samsung,pins = "gpj1-0"; + samsung,pin-function = <1>; + samsung,pin-val = <1>; + }; +}; -- 1.7.9.5