[PATCH 0/9] Add STiH407 fanmily pinctrl DT for tsin, tsout and mtsin channels

[PATCH 0/9] Add STiH407 fanmily pinctrl DT for tsin, tsout and mtsin channels

[Peter Griffin]

Hi folks,

This set adds in the necessary DT pinctrl configuration for the transport stream
input channels, transport stream output channels and merged transport stream input
channels for STiH407 family silicon.

Some of these channels have alternate pinctrl configurations depending on the board
design. These pinctrl groups will be used by the LinuxDVB c8sectpfe driver which
will be upstreamed in due course, which allows LDVB tuners and demodulators to be
used with an upstream kernel to get transport stream data into the SoC.

regards,

Peter.

Peter Griffin (9):
  ARM: STi: DT: Add STiH407 family tsin0 pinctrl configuration
  ARM: STi: DT: Add STiH407 family tsin1 pinctrl configuration
  ARM: STi: DT: Add STiH407 family tsin2 pinctrl configuration
  ARM: STi: DT: Add STiH407 family tsin3 pinctrl configuration
  ARM: STi: DT: Add STiH407 family tsin4 pinctrl configuration
  ARM: STi: DT: Add STiH407 family tsin5 pinctrl configuration
  ARM: STi: DT: Add STiH407 family tsout0 pinctrl configuration
  ARM: STi: DT: Add STiH407 family tsout1 pinctrl configuration
  ARM: STi: DT: Add STiH407 family mtsin0 pinctrl configuration

 arch/arm/boot/dts/stih407-pinctrl.dtsi | 200 +++++++++++++++++++++++++++++++++
 1 file changed, 200 insertions(+)

-- 
1.9.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 2/9] ARM: STi: DT: Add STiH407 family tsin1 pinctrl configuration

[Peter Griffin]

tsin1 channel can be configured for either serial or parallel data
transfer. This patch adds the pinctrl config for both possibilities.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
---
 arch/arm/boot/dts/stih407-pinctrl.dtsi | 28 ++++++++++++++++++++++++++++
 1 file changed, 28 insertions(+)

diff --git a/arch/arm/boot/dts/stih407-pinctrl.dtsi b/arch/arm/boot/dts/stih407-pinctrl.dtsi
index c8c8e84..7b1b652 100644
--- a/arch/arm/boot/dts/stih407-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stih407-pinctrl.dtsi
@@ -466,6 +466,34 @@
 					};
 				};
 			};
+
+			tsin1 {
+				pinctrl_tsin1_parallel: tsin1_parallel {
+					st,pins {
+						DATA7 = <&pio12 0 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						DATA6 = <&pio12 1 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						DATA5 = <&pio12 2 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						DATA4 = <&pio12 3 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						DATA3 = <&pio12 4 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						DATA2 = <&pio12 5 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						DATA1 = <&pio12 6 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						DATA0 = <&pio12 7 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						CLKIN = <&pio11 7 ALT1 IN CLKNOTDATA 0 CLK_A>;
+						VALID = <&pio11 5 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						ERROR = <&pio11 4 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						PKCLK = <&pio11 6 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+					};
+				};
+				pinctrl_tsin1_serial: tsin1_serial {
+					st,pins {
+						DATA7 = <&pio12 0 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						CLKIN = <&pio11 7 ALT1 IN CLKNOTDATA 0 CLK_A>;
+						VALID = <&pio11 5 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						ERROR = <&pio11 4 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						PKCLK = <&pio11 6 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+					};
+				};
+			};
 		};
 
 		pin-controller-front1 {
-- 
1.9.1

[PATCH 3/9] ARM: STi: DT: Add STiH407 family tsin2 pinctrl configuration

[Peter Griffin]

tsin2 channel can be configured for either serial or parallel data
transfer. This patch adds the pinctrl config for both possibilities.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
---
 arch/arm/boot/dts/stih407-pinctrl.dtsi | 28 ++++++++++++++++++++++++++++
 1 file changed, 28 insertions(+)

diff --git a/arch/arm/boot/dts/stih407-pinctrl.dtsi b/arch/arm/boot/dts/stih407-pinctrl.dtsi
index 7b1b652..6b11568 100644
--- a/arch/arm/boot/dts/stih407-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stih407-pinctrl.dtsi
@@ -494,6 +494,34 @@
 					};
 				};
 			};
+
+			tsin2 {
+				pinctrl_tsin2_parallel: tsin2_parallel {
+					st,pins {
+						DATA7 = <&pio13 4 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						DATA6 = <&pio13 5 ALT2 IN SE_NICLK_IO 0 CLK_B>;
+						DATA5 = <&pio13 6 ALT2 IN SE_NICLK_IO 0 CLK_B>;
+						DATA4 = <&pio13 7 ALT2 IN SE_NICLK_IO 0 CLK_B>;
+						DATA3 = <&pio14 0 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+						DATA2 = <&pio14 1 ALT2 IN SE_NICLK_IO 0 CLK_B>;
+						DATA1 = <&pio14 2 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+						DATA0 = <&pio14 3 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+						CLKIN = <&pio13 3 ALT1 IN CLKNOTDATA 0 CLK_A>;
+						VALID = <&pio13 1 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						ERROR = <&pio13 0 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						PKCLK = <&pio13 2 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+					};
+				};
+				pinctrl_tsin2_serial: tsin2_serial {
+					st,pins {
+						DATA7 = <&pio13 4 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						CLKIN = <&pio13 3 ALT1 IN CLKNOTDATA 0 CLK_A>;
+						VALID = <&pio13 1 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						ERROR = <&pio13 0 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						PKCLK = <&pio13 2 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+					};
+				};
+			};
 		};
 
 		pin-controller-front1 {
-- 
1.9.1

[PATCH 4/9] ARM: STi: DT: Add STiH407 family tsin3 pinctrl configuration

[Peter Griffin]

tsin3 channel can only be configured for serial data transfer.

On B2120 reference design tsin3 is brought out as TSB on the NIMB
slot of the B2004A daughter board.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
---
 arch/arm/boot/dts/stih407-pinctrl.dtsi | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm/boot/dts/stih407-pinctrl.dtsi b/arch/arm/boot/dts/stih407-pinctrl.dtsi
index 6b11568..13b469c 100644
--- a/arch/arm/boot/dts/stih407-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stih407-pinctrl.dtsi
@@ -522,6 +522,18 @@
 					};
 				};
 			};
+
+			tsin3 {
+				pinctrl_tsin3_serial: tsin3_serial {
+					st,pins {
+						DATA7 = <&pio14 1 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						CLKIN = <&pio14 0 ALT1 IN CLKNOTDATA 0 CLK_A>;
+						VALID = <&pio13 6 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						ERROR = <&pio13 5 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						PKCLK = <&pio13 7 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+					};
+				};
+			};
 		};
 
 		pin-controller-front1 {
-- 
1.9.1

[PATCH 5/9] ARM: STi: DT: Add STiH407 family tsin4 pinctrl configuration

[Peter Griffin]

tsin4 can only be configured for serial data transfer. However
depending on board design, two alternate pin configurations
are available. One in pin-controller-front0 and the other in
pin-controller-front1.

pinctrl_tsin4_serial_alt3 is brought out on B2120 reference
design as TSC on NIMA slot of the B2004A daughter board.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
---
 arch/arm/boot/dts/stih407-pinctrl.dtsi | 24 ++++++++++++++++++++++++
 1 file changed, 24 insertions(+)

diff --git a/arch/arm/boot/dts/stih407-pinctrl.dtsi b/arch/arm/boot/dts/stih407-pinctrl.dtsi
index 13b469c..702f42d 100644
--- a/arch/arm/boot/dts/stih407-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stih407-pinctrl.dtsi
@@ -534,6 +534,18 @@
 					};
 				};
 			};
+
+			tsin4 {
+				pinctrl_tsin4_serial_alt3: tsin4_serial_alt3 {
+					st,pins {
+						DATA7 = <&pio14 6 ALT3 IN SE_NICLK_IO 0 CLK_A>;
+						CLKIN = <&pio14 5 ALT3 IN CLKNOTDATA 0 CLK_A>;
+						VALID = <&pio14 3 ALT3 IN SE_NICLK_IO 0 CLK_B>;
+						ERROR = <&pio14 2 ALT3 IN SE_NICLK_IO 0 CLK_B>;
+						PKCLK = <&pio14 4 ALT3 IN SE_NICLK_IO 0 CLK_A>;
+					};
+				};
+			};
 		};
 
 		pin-controller-front1 {
@@ -547,6 +559,18 @@
 			interrupts-names = "irqmux";
 			ranges = <0 0x09210000 0x10000>;
 
+			tsin4 {
+				pinctrl_tsin4_serial_alt1: tsin4_serial_alt1 {
+					st,pins {
+						DATA7 = <&pio20 4 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						CLKIN = <&pio20 3 ALT1 IN CLKNOTDATA 0 CLK_A>;
+						VALID = <&pio20 1 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						ERROR = <&pio20 0 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						PKCLK = <&pio20 2 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+					};
+				};
+			};
+
 			pio20: pio@09210000 {
 				gpio-controller;
 				#gpio-cells = <1>;
-- 
1.9.1

[PATCH 6/9] ARM: STi: DT: Add STiH407 family tsin5 pinctrl configuration

[Peter Griffin]

tsin5 can only be configured for serial data transfer. However
depending on board design, two alternate tsin5 pin configurations
are available, both in pin-controller-front0.

pinctrl_tsin5_serial_alt1 is brought out on B2120 reference
design as TSD on NIMB slot of the B2004A daughter board.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
---
 arch/arm/boot/dts/stih407-pinctrl.dtsi | 21 +++++++++++++++++++++
 1 file changed, 21 insertions(+)

diff --git a/arch/arm/boot/dts/stih407-pinctrl.dtsi b/arch/arm/boot/dts/stih407-pinctrl.dtsi
index 702f42d..87d0722 100644
--- a/arch/arm/boot/dts/stih407-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stih407-pinctrl.dtsi
@@ -546,6 +546,27 @@
 					};
 				};
 			};
+
+			tsin5 {
+				pinctrl_tsin5_serial_alt1: tsin5_serial_alt1 {
+					st,pins {
+						DATA7 = <&pio18 4 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						CLKIN = <&pio18 3 ALT1 IN CLKNOTDATA 0 CLK_A>;
+						VALID = <&pio18 1 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						ERROR = <&pio18 0 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						PKCLK = <&pio18 2 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+					};
+				};
+				pinctrl_tsin5_serial_alt2: tsin5_serial_alt2 {
+					st,pins {
+						DATA7 = <&pio19 4 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+						CLKIN = <&pio19 3 ALT2 IN CLKNOTDATA 0 CLK_A>;
+						VALID = <&pio19 1 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+						ERROR = <&pio19 0 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+						PKCLK = <&pio19 2 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+					};
+				};
+			};
 		};
 
 		pin-controller-front1 {
-- 
1.9.1

[PATCH 1/9] ARM: STi: DT: Add STiH407 family tsin0 pinctrl configuration

[Peter Griffin]

tsin0 and be configured as either serial or parallel. This patch
adds the pinctrl config for both possiblities. On B2120 reference
design tsin0 is brought out as TSA on the NIMA slot of the B2004A
daughter board.

Signed-off-by: Peter Griffin <peter.griffin-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
---
 arch/arm/boot/dts/stih407-pinctrl.dtsi | 28 ++++++++++++++++++++++++++++
 1 file changed, 28 insertions(+)

diff --git a/arch/arm/boot/dts/stih407-pinctrl.dtsi b/arch/arm/boot/dts/stih407-pinctrl.dtsi
index 402844c..c8c8e84 100644
--- a/arch/arm/boot/dts/stih407-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stih407-pinctrl.dtsi
@@ -438,6 +438,34 @@
 					};
 				};
 			};
+
+			tsin0 {
+				pinctrl_tsin0_parallel: tsin0_parallel {
+					st,pins {
+						DATA7 = <&pio10 4 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						DATA6 = <&pio10 5 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						DATA5 = <&pio10 6 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						DATA4 = <&pio10 7 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						DATA3 = <&pio11 0 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						DATA2 = <&pio11 1 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						DATA1 = <&pio11 2 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						DATA0 = <&pio11 3 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						CLKIN = <&pio10 3 ALT1 IN CLKNOTDATA 0 CLK_A>;
+						VALID = <&pio10 1 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						ERROR = <&pio10 0 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						PKCLK = <&pio10 2 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+					};
+				};
+				pinctrl_tsin0_serial: tsin0_serial {
+					st,pins {
+						DATA7 = <&pio10 4 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						CLKIN = <&pio10 3 ALT1 IN CLKNOTDATA 0 CLK_A>;
+						VALID = <&pio10 1 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						ERROR = <&pio10 0 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						PKCLK = <&pio10 2 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+					};
+				};
+			};
 		};
 
 		pin-controller-front1 {
-- 
1.9.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 7/9] ARM: STi: DT: Add STiH407 family tsout0 pinctrl configuration

[Peter Griffin]

tsout0 channel can be configured for either serial or parallel
data transfer. Both pin configurations are provided.

Signed-off-by: Peter Griffin <peter.griffin-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
---
 arch/arm/boot/dts/stih407-pinctrl.dtsi | 28 ++++++++++++++++++++++++++++
 1 file changed, 28 insertions(+)

diff --git a/arch/arm/boot/dts/stih407-pinctrl.dtsi b/arch/arm/boot/dts/stih407-pinctrl.dtsi
index 87d0722..85cd9fc 100644
--- a/arch/arm/boot/dts/stih407-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stih407-pinctrl.dtsi
@@ -567,6 +567,34 @@
 					};
 				};
 			};
+
+			tsout0 {
+				pinctrl_tsout0_parallel: tsout0_parallel {
+					st,pins {
+						DATA7 = <&pio12 0 ALT3 OUT SE_NICLK_IO 0 CLK_A>;
+						DATA6 = <&pio12 1 ALT3 OUT SE_NICLK_IO 0 CLK_A>;
+						DATA5 = <&pio12 2 ALT3 OUT SE_NICLK_IO 0 CLK_A>;
+						DATA4 = <&pio12 3 ALT3 OUT SE_NICLK_IO 0 CLK_A>;
+						DATA3 = <&pio12 4 ALT3 OUT SE_NICLK_IO 0 CLK_A>;
+						DATA2 = <&pio12 5 ALT3 OUT SE_NICLK_IO 0 CLK_A>;
+						DATA1 = <&pio12 6 ALT3 OUT SE_NICLK_IO 0 CLK_A>;
+						DATA0 = <&pio12 7 ALT3 OUT SE_NICLK_IO 0 CLK_A>;
+						CLKIN = <&pio11 7 ALT3 OUT NICLK 0 CLK_A>;
+						VALID = <&pio11 5 ALT3 OUT SE_NICLK_IO 0 CLK_A>;
+						ERROR = <&pio11 4 ALT3 OUT SE_NICLK_IO 0 CLK_A>;
+						PKCLK = <&pio11 6 ALT3 OUT SE_NICLK_IO 0 CLK_A>;
+					};
+				};
+				pinctrl_tsout0_serial: tsout0_serial {
+					st,pins {
+						DATA7 = <&pio12 0 ALT3 OUT SE_NICLK_IO 0 CLK_A>;
+						CLKIN = <&pio11 7 ALT3 OUT NICLK 0 CLK_A>;
+						VALID = <&pio11 5 ALT3 OUT SE_NICLK_IO 0 CLK_A>;
+						ERROR = <&pio11 4 ALT3 OUT SE_NICLK_IO 0 CLK_A>;
+						PKCLK = <&pio11 6 ALT3 OUT SE_NICLK_IO 0 CLK_A>;
+					};
+				};
+			};
 		};
 
 		pin-controller-front1 {
-- 
1.9.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 8/9] ARM: STi: DT: Add STiH407 family tsout1 pinctrl configuration

[Peter Griffin]

tsout1 channel can only be configured for serial data tranfer.

Signed-off-by: Peter Griffin <peter.griffin-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
---
 arch/arm/boot/dts/stih407-pinctrl.dtsi | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm/boot/dts/stih407-pinctrl.dtsi b/arch/arm/boot/dts/stih407-pinctrl.dtsi
index 85cd9fc..af7f5f7 100644
--- a/arch/arm/boot/dts/stih407-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stih407-pinctrl.dtsi
@@ -595,6 +595,18 @@
 					};
 				};
 			};
+
+			tsout1 {
+				pinctrl_tsout1_serial: tsout1_serial {
+					st,pins {
+						DATA7 = <&pio19 4 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+						CLKIN = <&pio19 3 ALT1 OUT NICLK 0 CLK_A>;
+						VALID = <&pio19 1 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+						ERROR = <&pio19 0 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+						PKCLK = <&pio19 2 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+					};
+				};
+			};
 		};
 
 		pin-controller-front1 {
-- 
1.9.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH 0/9] Add STiH407 fanmily pinctrl DT for tsin, tsout and mtsin channels

[Maxime Coquelin]

Hi Peter,

On 06/10/2015 04:03 PM, Peter Griffin wrote:
> Hi folks,
>
> This set adds in the necessary DT pinctrl configuration for the transport stream
> input channels, transport stream output channels and merged transport stream input
> channels for STiH407 family silicon.
>
> Some of these channels have alternate pinctrl configurations depending on the board
> design. These pinctrl groups will be used by the LinuxDVB c8sectpfe driver which
> will be upstreamed in due course, which allows LDVB tuners and demodulators to be
> used with an upstream kernel to get transport stream data into the SoC.
>
> regards,
>
> Peter.
>
> Peter Griffin (9):
>    ARM: STi: DT: Add STiH407 family tsin0 pinctrl configuration
>    ARM: STi: DT: Add STiH407 family tsin1 pinctrl configuration
>    ARM: STi: DT: Add STiH407 family tsin2 pinctrl configuration
>    ARM: STi: DT: Add STiH407 family tsin3 pinctrl configuration
>    ARM: STi: DT: Add STiH407 family tsin4 pinctrl configuration
>    ARM: STi: DT: Add STiH407 family tsin5 pinctrl configuration
>    ARM: STi: DT: Add STiH407 family tsout0 pinctrl configuration
>    ARM: STi: DT: Add STiH407 family tsout1 pinctrl configuration
>    ARM: STi: DT: Add STiH407 family mtsin0 pinctrl configuration
>
>   arch/arm/boot/dts/stih407-pinctrl.dtsi | 200 +++++++++++++++++++++++++++++++++
>   1 file changed, 200 insertions(+)
>
Series applied for v4.3.

Thanks,
Maxime
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 9/9] ARM: STi: DT: Add STiH407 family mtsin0 pinctrl configuration

[Peter Griffin]

mtsin0 channel can only be configured for parallel data transfer.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
---
 arch/arm/boot/dts/stih407-pinctrl.dtsi | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)

diff --git a/arch/arm/boot/dts/stih407-pinctrl.dtsi b/arch/arm/boot/dts/stih407-pinctrl.dtsi
index af7f5f7..9494b35 100644
--- a/arch/arm/boot/dts/stih407-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stih407-pinctrl.dtsi
@@ -607,6 +607,25 @@
 					};
 				};
 			};
+
+			mtsin0 {
+				pinctrl_mtsin0_parallel: mtsin0_parallel {
+					st,pins {
+						DATA7 = <&pio10 4 ALT3 IN SE_NICLK_IO 0 CLK_A>;
+						DATA6 = <&pio10 5 ALT3 IN SE_NICLK_IO 0 CLK_A>;
+						DATA5 = <&pio10 6 ALT3 IN SE_NICLK_IO 0 CLK_A>;
+						DATA4 = <&pio10 7 ALT3 IN SE_NICLK_IO 0 CLK_A>;
+						DATA3 = <&pio11 0 ALT3 IN SE_NICLK_IO 0 CLK_A>;
+						DATA2 = <&pio11 1 ALT3 IN SE_NICLK_IO 0 CLK_A>;
+						DATA1 = <&pio11 2 ALT3 IN SE_NICLK_IO 0 CLK_A>;
+						DATA0 = <&pio11 3 ALT3 IN SE_NICLK_IO 0 CLK_A>;
+						CLKIN = <&pio10 3 ALT3 IN CLKNOTDATA 0 CLK_A>;
+						VALID = <&pio10 1 ALT3 IN SE_NICLK_IO 0 CLK_A>;
+						ERROR = <&pio10 0 ALT3 IN SE_NICLK_IO 0 CLK_A>;
+						PKCLK = <&pio10 2 ALT3 IN SE_NICLK_IO 0 CLK_A>;
+					};
+				};
+			};
 		};
 
 		pin-controller-front1 {
-- 
1.9.1