From: Josh Wu <josh.wu-AIFe0yeh4nAAvxtiuMwx3w@public.gmane.org>
To: Nicolas Ferre
<nicolas.ferre-AIFe0yeh4nAAvxtiuMwx3w@public.gmane.org>,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
Cc: Josh Wu <josh.wu-AIFe0yeh4nAAvxtiuMwx3w@public.gmane.org>,
Andrew Victor <linux-PelNFVqkFnVyf+4FbqDuWQ@public.gmane.org>,
Kumar Gala <galak-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>,
Jean-Christophe Plagniol-Villard
<plagnioj-sclMFOaUSTBWk0Htik3J/w@public.gmane.org>,
linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
Ian Campbell
<ijc+devicetree-KcIKpvwj1kUDXYZnReoRVg@public.gmane.org>,
devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
Rob Herring <robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>,
Pawel Moll <pawel.moll-5wv7dgnIgG8@public.gmane.org>,
Mark Rutland <mark.rutland-5wv7dgnIgG8@public.gmane.org>,
Russell King <linux-lFZ/pmaqli7XmaaqVzeoHQ@public.gmane.org>
Subject: [PATCH v2 1/2] ARM: at91: dts: add isi & ov2640 dt nodes for at91sam9m10g45ek board
Date: Tue, 16 Jun 2015 18:08:34 +0800 [thread overview]
Message-ID: <1434449315-9243-1-git-send-email-josh.wu@atmel.com> (raw)
First we group the isi data pins, and for now we only use 0~7 data pins
with HSYNC and VSYNC.
Also add the link for atmel-isi and ov2640 sensor node.
Signed-off-by: Josh Wu <josh.wu-AIFe0yeh4nAAvxtiuMwx3w@public.gmane.org>
---
Changes in v2:
- group the isi data pin.
- remove the isi_mck pin from pinctrl-isi as it will used by camera
sensor.
arch/arm/boot/dts/at91sam9g45.dtsi | 48 +++++++++++++++++++++-------------
arch/arm/boot/dts/at91sam9m10g45ek.dts | 45 +++++++++++++++++++++++++++++++
2 files changed, 75 insertions(+), 18 deletions(-)
diff --git a/arch/arm/boot/dts/at91sam9g45.dtsi b/arch/arm/boot/dts/at91sam9g45.dtsi
index d260ba7..f6220d6 100644
--- a/arch/arm/boot/dts/at91sam9g45.dtsi
+++ b/arch/arm/boot/dts/at91sam9g45.dtsi
@@ -498,23 +498,31 @@
};
isi {
- pinctrl_isi: isi-0 {
- atmel,pins = <AT91_PIOB 8 AT91_PERIPH_B AT91_PINCTRL_NONE /* D8 */
- AT91_PIOB 9 AT91_PERIPH_B AT91_PINCTRL_NONE /* D9 */
- AT91_PIOB 10 AT91_PERIPH_B AT91_PINCTRL_NONE /* D10 */
- AT91_PIOB 11 AT91_PERIPH_B AT91_PINCTRL_NONE /* D11 */
- AT91_PIOB 20 AT91_PERIPH_A AT91_PINCTRL_NONE /* D0 */
- AT91_PIOB 21 AT91_PERIPH_A AT91_PINCTRL_NONE /* D1 */
- AT91_PIOB 22 AT91_PERIPH_A AT91_PINCTRL_NONE /* D2 */
- AT91_PIOB 23 AT91_PERIPH_A AT91_PINCTRL_NONE /* D3 */
- AT91_PIOB 24 AT91_PERIPH_A AT91_PINCTRL_NONE /* D4 */
- AT91_PIOB 25 AT91_PERIPH_A AT91_PINCTRL_NONE /* D5 */
- AT91_PIOB 26 AT91_PERIPH_A AT91_PINCTRL_NONE /* D6 */
- AT91_PIOB 27 AT91_PERIPH_A AT91_PINCTRL_NONE /* D7 */
- AT91_PIOB 28 AT91_PERIPH_A AT91_PINCTRL_NONE /* PCK */
- AT91_PIOB 29 AT91_PERIPH_A AT91_PINCTRL_NONE /* VSYNC */
- AT91_PIOB 30 AT91_PERIPH_A AT91_PINCTRL_NONE /* HSYNC */
- AT91_PIOB 31 AT91_PERIPH_A AT91_PINCTRL_NONE /* MCK */>;
+ pinctrl_isi_data_0_7: isi-0-data-0-7 {
+ atmel,pins =
+ <AT91_PIOB 20 AT91_PERIPH_A AT91_PINCTRL_NONE /* D0 */
+ AT91_PIOB 21 AT91_PERIPH_A AT91_PINCTRL_NONE /* D1 */
+ AT91_PIOB 22 AT91_PERIPH_A AT91_PINCTRL_NONE /* D2 */
+ AT91_PIOB 23 AT91_PERIPH_A AT91_PINCTRL_NONE /* D3 */
+ AT91_PIOB 24 AT91_PERIPH_A AT91_PINCTRL_NONE /* D4 */
+ AT91_PIOB 25 AT91_PERIPH_A AT91_PINCTRL_NONE /* D5 */
+ AT91_PIOB 26 AT91_PERIPH_A AT91_PINCTRL_NONE /* D6 */
+ AT91_PIOB 27 AT91_PERIPH_A AT91_PINCTRL_NONE /* D7 */
+ AT91_PIOB 28 AT91_PERIPH_A AT91_PINCTRL_NONE /* PCK */
+ AT91_PIOB 29 AT91_PERIPH_A AT91_PINCTRL_NONE /* VSYNC */
+ AT91_PIOB 30 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* HSYNC */
+ };
+
+ pinctrl_isi_data_8_9: isi-0-data-8-9 {
+ atmel,pins =
+ <AT91_PIOB 8 AT91_PERIPH_B AT91_PINCTRL_NONE /* D8 */
+ AT91_PIOB 9 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* D9 */
+ };
+
+ pinctrl_isi_data_10_11: isi-0-data-10-11 {
+ atmel,pins =
+ <AT91_PIOB 10 AT91_PERIPH_B AT91_PINCTRL_NONE /* D10 */
+ AT91_PIOB 11 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* D11 */
};
};
@@ -1068,8 +1076,12 @@
clocks = <&isi_clk>;
clock-names = "isi_clk";
pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_isi>;
+ pinctrl-0 = <&pinctrl_isi_data_0_7>;
status = "disabled";
+ port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
};
pwm0: pwm@fffb8000 {
diff --git a/arch/arm/boot/dts/at91sam9m10g45ek.dts b/arch/arm/boot/dts/at91sam9m10g45ek.dts
index 1375d33..5062e18 100644
--- a/arch/arm/boot/dts/at91sam9m10g45ek.dts
+++ b/arch/arm/boot/dts/at91sam9m10g45ek.dts
@@ -63,6 +63,25 @@
i2c0: i2c@fff84000 {
status = "okay";
+ ov2640: camera@30 {
+ compatible = "ovti,ov2640";
+ reg = <0x30>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pck1_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>;
+ resetb-gpios = <&pioD 12 GPIO_ACTIVE_LOW>;
+ pwdn-gpios = <&pioD 13 GPIO_ACTIVE_HIGH>;
+ clocks = <&pck1>;
+ clock-names = "xvclk";
+ assigned-clocks = <&pck1>;
+ assigned-clock-rates = <25000000>;
+
+ port {
+ ov2640_0: endpoint {
+ remote-endpoint = <&isi_0>;
+ bus-width = <8>;
+ };
+ };
+ };
};
i2c1: i2c@fff88000 {
@@ -101,6 +120,22 @@
};
pinctrl@fffff200 {
+ camera_sensor {
+ pinctrl_pck1_as_isi_mck: pck1_as_isi_mck-0 {
+ atmel,pins =
+ <AT91_PIOB 31 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_sensor_reset: sensor_reset-0 {
+ atmel,pins =
+ <AT91_PIOD 12 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_sensor_power: sensor_power-0 {
+ atmel,pins =
+ <AT91_PIOD 13 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+ };
+ };
mmc0 {
pinctrl_board_mmc0: mmc0-board {
atmel,pins =
@@ -155,6 +190,16 @@
status = "okay";
};
+ isi@fffb4000 {
+ status = "okay";
+ port {
+ isi_0: endpoint {
+ remote-endpoint = <&ov2640_0>;
+ bus-width = <8>;
+ };
+ };
+ };
+
pwm0: pwm@fffb8000 {
status = "okay";
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
next reply other threads:[~2015-06-16 10:08 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-06-16 10:08 Josh Wu [this message]
[not found] ` <1434449315-9243-1-git-send-email-josh.wu-AIFe0yeh4nAAvxtiuMwx3w@public.gmane.org>
2015-06-18 15:45 ` [PATCH v2 1/2] ARM: at91: dts: add isi & ov2640 dt nodes for at91sam9m10g45ek board Alexandre Belloni
2015-07-30 12:03 ` Nicolas Ferre
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1434449315-9243-1-git-send-email-josh.wu@atmel.com \
--to=josh.wu-aife0yeh4naavxtiumwx3w@public.gmane.org \
--cc=devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=galak-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org \
--cc=ijc+devicetree-KcIKpvwj1kUDXYZnReoRVg@public.gmane.org \
--cc=linux-PelNFVqkFnVyf+4FbqDuWQ@public.gmane.org \
--cc=linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org \
--cc=linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=linux-lFZ/pmaqli7XmaaqVzeoHQ@public.gmane.org \
--cc=mark.rutland-5wv7dgnIgG8@public.gmane.org \
--cc=nicolas.ferre-AIFe0yeh4nAAvxtiuMwx3w@public.gmane.org \
--cc=pawel.moll-5wv7dgnIgG8@public.gmane.org \
--cc=plagnioj-sclMFOaUSTBWk0Htik3J/w@public.gmane.org \
--cc=robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).