From: Peter Griffin <peter.griffin@linaro.org>
To: linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, srinivas.kandagatla@gmail.com,
maxime.coquelin@st.com, patrice.chotard@st.com,
mchehab@osg.samsung.com
Cc: peter.griffin@linaro.org, lee.jones@linaro.org,
hugues.fruchet@st.com, linux-media@vger.kernel.org,
devicetree@vger.kernel.org
Subject: [PATCH 06/12] ARM: DT: STi: STiH407: Add c8sectpfe LinuxDVB DT node.
Date: Wed, 24 Jun 2015 16:11:04 +0100 [thread overview]
Message-ID: <1435158670-7195-7-git-send-email-peter.griffin@linaro.org> (raw)
In-Reply-To: <1435158670-7195-1-git-send-email-peter.griffin@linaro.org>
This patch adds in the required DT node for the c8sectpfe
Linux DVB demux driver which allows the tsin channels
to be used on an upstream kernel.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
---
arch/arm/boot/dts/stihxxx-b2120.dtsi | 50 ++++++++++++++++++++++++++++++++++++
1 file changed, 50 insertions(+)
diff --git a/arch/arm/boot/dts/stihxxx-b2120.dtsi b/arch/arm/boot/dts/stihxxx-b2120.dtsi
index 1f27589..ece2ede 100644
--- a/arch/arm/boot/dts/stihxxx-b2120.dtsi
+++ b/arch/arm/boot/dts/stihxxx-b2120.dtsi
@@ -6,6 +6,10 @@
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
+
+#include <dt-bindings/clock/stih407-clks.h>
+#include <dt-bindings/media/c8sectpfe.h>
+
/ {
soc {
sbc_serial0: serial@9530000 {
@@ -72,5 +76,51 @@
st,osc-force-ext;
};
};
+
+ c8sectpfe@08a20000 {
+ compatible = "st,stih407-c8sectpfe";
+ status = "okay";
+ reg = <0x08a20000 0x10000>, <0x08a00000 0x4000>;
+ reg-names = "c8sectpfe", "c8sectpfe-ram";
+
+ interrupts = <0 34 0>, <0 35 0>;
+ interrupt-names = "c8sectpfe-error-irq",
+ "c8sectpfe-idle-irq";
+
+ pinctrl-names = "tsin0-serial", "tsin0-parallel",
+ "tsin3-serial", "tsin4-serial",
+ "tsin5-serial";
+
+ pinctrl-0 = <&pinctrl_tsin0_serial>;
+ pinctrl-1 = <&pinctrl_tsin0_parallel>;
+ pinctrl-2 = <&pinctrl_tsin3_serial>;
+ pinctrl-3 = <&pinctrl_tsin4_serial_alt3>;
+ pinctrl-4 = <&pinctrl_tsin5_serial_alt1>;
+
+ clocks = <&clk_s_c0_flexgen CLK_PROC_STFE>;
+ clock-names = "c8sectpfe";
+
+ /* tsin0 is TSA on NIMA */
+ tsin0: port@0 {
+
+ tsin-num = <0>;
+ serial-not-parallel;
+ i2c-bus = <&ssc2>;
+ rst-gpio = <&pio15 4 0>;
+
+ dvb-card = <STV0367_TDA18212_NIMA_1>;
+ };
+
+ /* tsin3 is TSB on NIMB */
+ tsin3: port@3 {
+
+ tsin-num = <3>;
+ serial-not-parallel;
+ i2c-bus = <&ssc3>;
+ rst-gpio = <&pio15 7 0>;
+
+ dvb-card = <STV0367_PLL_BOARD_NIMB>;
+ };
+ };
};
};
--
1.9.1
next prev parent reply other threads:[~2015-06-24 15:11 UTC|newest]
Thread overview: 32+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-06-24 15:10 [PATCH 00/12] Add c8sectpfe LinuxDVB demux driver Peter Griffin
2015-06-24 15:10 ` [PATCH 01/12] ARM: DT: STi: stihxxx-b2120: Add pulse-width properties to ssc2 & ssc3 Peter Griffin
2015-06-24 15:11 ` [PATCH 03/12] [media] stv0367: Refine i2c error trace to include i2c address Peter Griffin
2015-06-24 15:11 ` [PATCH 04/12] [media] stv0367: Add support for 16Mhz reference clock Peter Griffin
2015-06-24 15:11 ` [PATCH 05/12] [media] tsin: c8sectpfe: Add DT bindings documentation for c8sectpfe driver Peter Griffin
2015-06-24 15:11 ` Peter Griffin [this message]
2015-06-24 15:11 ` [PATCH 07/12] [media] tsin: c8sectpfe: STiH407/10 Linux DVB demux support Peter Griffin
[not found] ` <1435158670-7195-8-git-send-email-peter.griffin-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
2015-07-22 21:46 ` Mauro Carvalho Chehab
2015-07-30 11:08 ` Peter Griffin
2015-06-24 15:11 ` [PATCH 08/12] [media] tsin: c8sectpfe: Add LDVB helper functions Peter Griffin
[not found] ` <1435158670-7195-1-git-send-email-peter.griffin-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
2015-06-24 15:11 ` [PATCH 02/12] [media] dvb-pll: Add support for THOMSON DTT7546X tuner Peter Griffin
[not found] ` <1435158670-7195-3-git-send-email-peter.griffin-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
2015-06-25 1:17 ` Joe Perches
2015-07-22 21:58 ` Mauro Carvalho Chehab
[not found] ` <20150722185811.2d718baa-+RedX5hVuTR+urZeOPWqwQ@public.gmane.org>
2015-07-30 9:47 ` Peter Griffin
2015-07-30 10:08 ` Joe Perches
[not found] ` <1438250928.2677.10.camel-6d6DIl74uiNBDgjK7y7TUQ@public.gmane.org>
2015-07-30 11:14 ` Michael Ira Krufky
[not found] ` <CAOcJUbw5hSmPdrz6rPPYU6iMBHnvOZc1p3f+4WhEYq2-XmAPVw-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2015-07-30 11:17 ` Michael Ira Krufky
2015-07-30 14:33 ` Peter Griffin
2015-07-30 11:37 ` Michael Ira Krufky
2015-07-30 14:34 ` Peter Griffin
2015-07-22 17:10 ` Mauro Carvalho Chehab
2015-07-30 9:46 ` Peter Griffin
2015-06-24 15:11 ` [PATCH 09/12] [media] tsin: c8sectpfe: Add support for various ST NIM cards Peter Griffin
2015-07-22 21:53 ` Mauro Carvalho Chehab
2015-07-30 9:43 ` Peter Griffin
2015-06-24 15:11 ` [PATCH 10/12] [media] tsin: c8sectpfe: Add c8sectpfe debugfs support Peter Griffin
2015-06-24 15:11 ` [PATCH 11/12] [media] tsin: c8sectpfe: Add Kconfig and Makefile for the driver Peter Griffin
2015-06-25 7:23 ` Paul Bolle
2015-07-22 7:38 ` Peter Griffin
2015-07-22 21:56 ` Mauro Carvalho Chehab
2015-07-30 9:39 ` Peter Griffin
2015-06-24 15:11 ` [PATCH 12/12] MAINTAINERS: Add c8sectpfe driver directory to STi section Peter Griffin
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1435158670-7195-7-git-send-email-peter.griffin@linaro.org \
--to=peter.griffin@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=hugues.fruchet@st.com \
--cc=lee.jones@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-media@vger.kernel.org \
--cc=maxime.coquelin@st.com \
--cc=mchehab@osg.samsung.com \
--cc=patrice.chotard@st.com \
--cc=srinivas.kandagatla@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).