From: Peter Chen <peter.chen-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
To: shawn.guo-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org,
kernel-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org,
devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org,
pawel.moll-5wv7dgnIgG8@public.gmane.org,
mark.rutland-5wv7dgnIgG8@public.gmane.org,
s.hauer-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org,
gregkh-hQyY1W1yCW8ekmWlsbkhG0B+6BGkLq7r@public.gmane.org,
jun.li-KZfg59tc24xl57MIdRCFDg@public.gmane.org,
linux-usb-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
Peter Chen <peter.chen-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
Subject: [PATCH v2 10/10] usb: chipidea: add tx/rx burst size configuration interface
Date: Mon, 3 Aug 2015 12:47:18 +0800 [thread overview]
Message-ID: <1438577238-10153-11-git-send-email-peter.chen@freescale.com> (raw)
In-Reply-To: <1438577238-10153-1-git-send-email-peter.chen-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
The user can adjust it through dts or platform data
Signed-off-by: Peter Chen <peter.chen-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
---
drivers/usb/chipidea/bits.h | 4 ++++
drivers/usb/chipidea/ci.h | 1 +
drivers/usb/chipidea/core.c | 35 +++++++++++++++++++++++++++++++++++
include/linux/usb/chipidea.h | 4 ++++
4 files changed, 44 insertions(+)
diff --git a/drivers/usb/chipidea/bits.h b/drivers/usb/chipidea/bits.h
index 462ad02..e462f55 100644
--- a/drivers/usb/chipidea/bits.h
+++ b/drivers/usb/chipidea/bits.h
@@ -61,6 +61,10 @@
/* Set non-zero value for internal TT Hub address representation */
#define TTCTRL_TTHA (0x7fUL << 24)
+/* BURSTSIZE */
+#define RX_BURST_MASK 0xff
+#define TX_BURST_MASK 0xff00
+
/* PORTSC */
#define PORTSC_CCS BIT(0)
#define PORTSC_CSC BIT(1)
diff --git a/drivers/usb/chipidea/ci.h b/drivers/usb/chipidea/ci.h
index b562544..41d7cf6 100644
--- a/drivers/usb/chipidea/ci.h
+++ b/drivers/usb/chipidea/ci.h
@@ -51,6 +51,7 @@ enum ci_hw_regs {
OP_DEVICEADDR,
OP_ENDPTLISTADDR,
OP_TTCTRL,
+ OP_BURSTSIZE,
OP_PORTSC,
OP_DEVLC,
OP_OTGSC,
diff --git a/drivers/usb/chipidea/core.c b/drivers/usb/chipidea/core.c
index f60cbf6..0375412 100644
--- a/drivers/usb/chipidea/core.c
+++ b/drivers/usb/chipidea/core.c
@@ -86,6 +86,7 @@ static const u8 ci_regs_nolpm[] = {
[OP_DEVICEADDR] = 0x14U,
[OP_ENDPTLISTADDR] = 0x18U,
[OP_TTCTRL] = 0x1CU,
+ [OP_BURSTSIZE] = 0x20U,
[OP_PORTSC] = 0x44U,
[OP_DEVLC] = 0x84U,
[OP_OTGSC] = 0x64U,
@@ -109,6 +110,7 @@ static const u8 ci_regs_lpm[] = {
[OP_DEVICEADDR] = 0x14U,
[OP_ENDPTLISTADDR] = 0x18U,
[OP_TTCTRL] = 0x1CU,
+ [OP_BURSTSIZE] = 0x20U,
[OP_PORTSC] = 0x44U,
[OP_DEVLC] = 0x84U,
[OP_OTGSC] = 0xC4U,
@@ -442,6 +444,17 @@ void ci_platform_configure(struct ci_hdrc *ci)
if (ci->platdata->flags & CI_HDRC_OVERRIDE_AHB_BURST)
hw_write_id_reg(ci, ID_SBUSCFG, AHBBRST_MASK,
ci->platdata->ahb_burst_config);
+
+ /* override burst size, take effect only when ahb_burst_config is 0 */
+ if (!hw_read_id_reg(ci, ID_SBUSCFG, AHBBRST_MASK)) {
+ if (ci->platdata->flags & CI_HDRC_OVERRIDE_TX_BURST)
+ hw_write(ci, OP_BURSTSIZE, TX_BURST_MASK,
+ ci->platdata->tx_burst_size << __ffs(TX_BURST_MASK));
+
+ if (ci->platdata->flags & CI_HDRC_OVERRIDE_RX_BURST)
+ hw_write(ci, OP_BURSTSIZE, RX_BURST_MASK,
+ ci->platdata->rx_burst_size);
+ }
}
/**
@@ -661,6 +674,28 @@ static int ci_get_platdata(struct device *dev,
platdata->flags |= CI_HDRC_OVERRIDE_AHB_BURST;
}
+ if (of_find_property(dev->of_node, "tx-burst-size-dword", NULL)) {
+ ret = of_property_read_u32(dev->of_node, "tx-burst-size-dword",
+ &platdata->tx_burst_size);
+ if (ret) {
+ dev_err(dev,
+ "failed to get tx-burst-size-dword\n");
+ return ret;
+ }
+ platdata->flags |= CI_HDRC_OVERRIDE_TX_BURST;
+ }
+
+ if (of_find_property(dev->of_node, "rx-burst-size-dword", NULL)) {
+ ret = of_property_read_u32(dev->of_node, "rx-burst-size-dword",
+ &platdata->rx_burst_size);
+ if (ret) {
+ dev_err(dev,
+ "failed to get rx-burst-size-dword\n");
+ return ret;
+ }
+ platdata->flags |= CI_HDRC_OVERRIDE_RX_BURST;
+ }
+
return 0;
}
diff --git a/include/linux/usb/chipidea.h b/include/linux/usb/chipidea.h
index fe3c8eb..a41833c 100644
--- a/include/linux/usb/chipidea.h
+++ b/include/linux/usb/chipidea.h
@@ -34,6 +34,8 @@ struct ci_hdrc_platform_data {
#define CI_HDRC_TURN_VBUS_EARLY_ON BIT(7)
#define CI_HDRC_SET_NON_ZERO_TTHA BIT(8)
#define CI_HDRC_OVERRIDE_AHB_BURST BIT(9)
+#define CI_HDRC_OVERRIDE_TX_BURST BIT(10)
+#define CI_HDRC_OVERRIDE_RX_BURST BIT(11)
enum usb_dr_mode dr_mode;
#define CI_HDRC_CONTROLLER_RESET_EVENT 0
#define CI_HDRC_CONTROLLER_STOPPED_EVENT 1
@@ -44,6 +46,8 @@ struct ci_hdrc_platform_data {
/* interrupt threshold setting */
u32 itc_setting;
u32 ahb_burst_config;
+ u32 tx_burst_size;
+ u32 rx_burst_size;
};
/* Default offset of capability registers */
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
next prev parent reply other threads:[~2015-08-03 4:47 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-08-03 4:47 [PATCH v2 00/10] USB: chipidea misc patches Peter Chen
[not found] ` <1438577238-10153-1-git-send-email-peter.chen-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
2015-08-03 4:47 ` [PATCH v2 01/10] usb: chipidea: udc: zero-length packet is only needed for TX Peter Chen
2015-08-03 4:47 ` [PATCH v2 02/10] usb: chipidea: define stream mode disable for both roles Peter Chen
2015-08-03 4:47 ` [PATCH v2 03/10] usb: chipidea: imx: add stream mode enable for device mode at imx6sl/imx6sx Peter Chen
2015-08-03 4:47 ` [PATCH v2 04/10] Doc: usb: ci-hdrc-usb2: add ahb-burst-config for binding doc Peter Chen
[not found] ` <1438577238-10153-5-git-send-email-peter.chen-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
2015-08-03 14:00 ` Rob Herring
2015-08-03 4:47 ` [PATCH v2 05/10] ARM: imx6: set ahb-burst-config as 0 for USB Peter Chen
2015-08-03 4:47 ` [PATCH v2 06/10] usb: chipidea: add ahb burst configuration interface Peter Chen
[not found] ` <1438577238-10153-7-git-send-email-peter.chen-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
2015-08-03 14:04 ` Rob Herring
[not found] ` <CAL_JsqJn16OvfL_Ggf1wSi2XkJkjDMrmuRit3q8eVY5bNp8oYw-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2015-08-04 0:36 ` Peter Chen
2015-08-05 1:25 ` Peter Chen
2015-08-03 4:47 ` [PATCH v2 07/10] usb: chipidea: usbmisc_imx: add non-burst setting for imx6 Peter Chen
2015-08-03 4:47 ` [PATCH v2 08/10] Doc: usb: ci-hdrc-usb2: add tx(rx)-burst-config-dword for binding doc Peter Chen
2015-08-03 4:47 ` [PATCH v2 09/10] ARM: imx6: change default burst size for USB Peter Chen
2015-08-03 4:47 ` Peter Chen [this message]
2015-08-05 14:08 ` [PATCH v2 00/10] USB: chipidea misc patches Shawn Guo
2015-09-22 6:03 ` Peter Chen
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1438577238-10153-11-git-send-email-peter.chen@freescale.com \
--to=peter.chen-kzfg59tc24xl57midrcfdg@public.gmane.org \
--cc=devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=gregkh-hQyY1W1yCW8ekmWlsbkhG0B+6BGkLq7r@public.gmane.org \
--cc=jun.li-KZfg59tc24xl57MIdRCFDg@public.gmane.org \
--cc=kernel-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org \
--cc=linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org \
--cc=linux-usb-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=mark.rutland-5wv7dgnIgG8@public.gmane.org \
--cc=pawel.moll-5wv7dgnIgG8@public.gmane.org \
--cc=robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org \
--cc=s.hauer-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org \
--cc=shawn.guo-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).