From: Olliver Schinagl <o.schinagl@ultimaker.com>
To: Olliver Schinagl <o.schinagl@ultimaker.com>,
Rob Herring <robh+dt@kernel.org>, Pawel Moll <pawel.moll@arm.com>,
Mark Rutland <mark.rutland@arm.com>,
Ian Campbell <ijc+devicetree@hellion.org.uk>,
Kumar Gala <galak@codeaurora.org>,
Russell King <linux@arm.linux.org.uk>,
Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org
Subject: [PATCH v2 1/1] ARM: dts: sun7i: Enable axp209 driver on olinuxino lime2
Date: Wed, 9 Sep 2015 15:26:44 +0200 [thread overview]
Message-ID: <1441805204-6037-2-git-send-email-o.schinagl@ultimaker.com> (raw)
In-Reply-To: <1441805204-6037-1-git-send-email-o.schinagl@ultimaker.com>
The Olimex OLinuXino Lime2 uses the same AXP209 as was recently
introduced this driver for its power regulation.
Signed-off-by: Olliver Schinagl <o.schinagl@ultimaker.com>
---
arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts | 87 +++++++++----------------
1 file changed, 31 insertions(+), 56 deletions(-)
diff --git a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts b/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts
index d5c796c..dd90a1d 100644
--- a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts
+++ b/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts
@@ -71,14 +71,6 @@
default-state = "on";
};
};
-
- reg_axp_ipsout: axp_ipsout {
- compatible = "regulator-fixed";
- regulator-name = "axp-ipsout";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- regulator-always-on;
- };
};
&ahci {
@@ -86,6 +78,10 @@
status = "okay";
};
+&cpu0 {
+ cpu-supply = <®_dcdc2>;
+};
+
&ehci0 {
status = "okay";
};
@@ -112,57 +108,9 @@
status = "okay";
axp209: pmic@34 {
- compatible = "x-powers,axp209";
reg = <0x34>;
interrupt-parent = <&nmi_intc>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
-
- interrupt-controller;
- #interrupt-cells = <1>;
-
- acin-supply = <®_axp_ipsout>;
- vin2-supply = <®_axp_ipsout>;
- vin3-supply = <®_axp_ipsout>;
- ldo24in-supply = <®_axp_ipsout>;
- ldo3in-supply = <®_axp_ipsout>;
-
- regulators {
- vdd_rtc: ldo1 {
- regulator-min-microvolt = <1300000>;
- regulator-max-microvolt = <1300000>;
- regulator-always-on;
- };
-
- avcc: ldo2 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
-
- vcc_csi0: ldo3 {
- regulator-min-microvolt = <700000>;
- regulator-max-microvolt = <3500000>;
- regulator-always-on;
- };
-
- vcc_csi1: ldo4 {
- regulator-min-microvolt = <1250000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
-
- vdd_cpu: dcdc2 {
- regulator-min-microvolt = <700000>;
- regulator-max-microvolt = <2275000>;
- regulator-always-on;
- };
-
- vdd_int: dcdc3 {
- regulator-min-microvolt = <700000>;
- regulator-max-microvolt = <3500000>;
- regulator-always-on;
- };
- };
};
};
@@ -243,6 +191,33 @@
status = "okay";
};
+#include "axp209.dtsi"
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1450000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-int-dll";
+};
+
+®_ldo1 {
+ regulator-name = "vdd-rtc";
+};
+
+®_ldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
®_usb0_vbus {
pinctrl-0 = <&usb0_vbus_pin_lime2>;
gpio = <&pio 2 17 GPIO_ACTIVE_HIGH>;
--
2.1.4
next prev parent reply other threads:[~2015-09-09 13:26 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-09-09 13:26 [PATCH v2 0/1] Enable axp209 on OLinuXino lime2 Olliver Schinagl
2015-09-09 13:26 ` Olliver Schinagl [this message]
2015-09-10 18:13 ` [PATCH v2 1/1] ARM: dts: sun7i: Enable axp209 driver on olinuxino lime2 Maxime Ripard
2015-09-11 2:57 ` Chen-Yu Tsai
[not found] ` <CAGb2v67GTAM3tqOUOmUjKmWGyewJar2NWAzF4bk4g+-7Yfdm0A-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2015-09-11 6:37 ` Olliver Schinagl
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1441805204-6037-2-git-send-email-o.schinagl@ultimaker.com \
--to=o.schinagl@ultimaker.com \
--cc=devicetree@vger.kernel.org \
--cc=galak@codeaurora.org \
--cc=ijc+devicetree@hellion.org.uk \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@arm.linux.org.uk \
--cc=mark.rutland@arm.com \
--cc=maxime.ripard@free-electrons.com \
--cc=pawel.moll@arm.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).