devicetree.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Charles Keepax <ckeepax-yzvPICuk2AATkU/dhu1WVueM+bqZidxxQQ4Iyu8u01E@public.gmane.org>
To: cw00.choi-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org,
	lee.jones-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org
Cc: myungjoo.ham-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org,
	sameo-VuQAYsv1563Yd54FQh9/CA@public.gmane.org,
	devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
	linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
	patches-yzvPICuk2AATkU/dhu1WVueM+bqZidxxQQ4Iyu8u01E@public.gmane.org
Subject: [PATCH v2 6/6] mfd: arizona: Update DT binding documentation for jack detection
Date: Fri, 11 Sep 2015 13:14:18 +0100	[thread overview]
Message-ID: <1441973658-26234-7-git-send-email-ckeepax@opensource.wolfsonmicro.com> (raw)
In-Reply-To: <1441973658-26234-1-git-send-email-ckeepax-yzvPICuk2AATkU/dhu1WVueM+bqZidxxQQ4Iyu8u01E@public.gmane.org>

Add additional bindings for both inverting the polarity of the jack
detection pins and allowing the use of a second jack detection pin. Note
that the second jack detection pin is hard wired in the chip so can only
be enabled through the binding, rather than a pin being specified.

Signed-off-by: Charles Keepax <ckeepax-yzvPICuk2AATkU/dhu1WVueM+bqZidxxQQ4Iyu8u01E@public.gmane.org>
Reviewed-by: Chanwoo Choi <cw00.choi-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
---

Changes since v1:
 - Fixed minor typo

 Documentation/devicetree/bindings/mfd/arizona.txt |    6 ++++++
 1 files changed, 6 insertions(+), 0 deletions(-)

diff --git a/Documentation/devicetree/bindings/mfd/arizona.txt b/Documentation/devicetree/bindings/mfd/arizona.txt
index b98a11b..cb3a652 100644
--- a/Documentation/devicetree/bindings/mfd/arizona.txt
+++ b/Documentation/devicetree/bindings/mfd/arizona.txt
@@ -73,6 +73,12 @@ Optional properties:
     If this node is not mentioned or if the value is unknown, then
     headphone detection mode is set to HPDETL.
 
+  - wlf,use-jd-gpio : Use GPIO input along with JD1 for dual pin jack
+    detection.
+  - wlf,use-jd-gpio-nopull : Internal pull on GPIO is disabled when used for
+    jack detection.
+  - wlf,jd-invert : Invert the polarity of the jack detection switch
+
   - wlf,micd-software-compare : Use a software comparison to determine mic
     presence
   - wlf,micd-detect-debounce : Additional software microphone detection
-- 
1.7.2.5

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

  parent reply	other threads:[~2015-09-11 12:14 UTC|newest]

Thread overview: 11+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2015-09-11 12:14 [PATCH v2 0/6] Arizona extcon improvements Charles Keepax
     [not found] ` <1441973658-26234-1-git-send-email-ckeepax-yzvPICuk2AATkU/dhu1WVueM+bqZidxxQQ4Iyu8u01E@public.gmane.org>
2015-09-11 12:14   ` [PATCH v2 1/6] mfd: arizona: Add TST_CAP bits for headphone detection Charles Keepax
     [not found]     ` <1441973658-26234-2-git-send-email-ckeepax-yzvPICuk2AATkU/dhu1WVueM+bqZidxxQQ4Iyu8u01E@public.gmane.org>
2015-09-11 12:24       ` Charles Keepax
2015-09-11 12:37         ` [PATCH v3 " Charles Keepax
2015-09-15  4:05           ` Chanwoo Choi
2015-09-15  9:33             ` Charles Keepax
2015-09-11 12:14   ` [PATCH v2 2/6] extcon: arizona: Additional settings to improve accuracy of HP detect Charles Keepax
2015-09-11 12:14   ` [PATCH v2 4/6] extcon: arizona: Add device binding for jack detect polarity inversion Charles Keepax
2015-09-11 12:14   ` Charles Keepax [this message]
2015-09-11 12:14 ` [PATCH v2 3/6] extcon: arizona: Ignore jd_invert for MICD_CLAMP_STS Charles Keepax
2015-09-11 12:14 ` [PATCH v2 5/6] extcon: arizona: Add device binding for second jack detect pin on GPIO5 Charles Keepax

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1441973658-26234-7-git-send-email-ckeepax@opensource.wolfsonmicro.com \
    --to=ckeepax-yzvpicuk2aatku/dhu1wvuem+bqzidxxqq4iyu8u01e@public.gmane.org \
    --cc=cw00.choi-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org \
    --cc=devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
    --cc=lee.jones-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org \
    --cc=linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
    --cc=myungjoo.ham-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org \
    --cc=patches-yzvPICuk2AATkU/dhu1WVueM+bqZidxxQQ4Iyu8u01E@public.gmane.org \
    --cc=sameo-VuQAYsv1563Yd54FQh9/CA@public.gmane.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).