From: Andreas Dannenberg <dannenberg-l0cyMroinI0@public.gmane.org>
To: Sebastian Reichel <sre-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>,
Dmitry Eremin-Solenikov
<dbaryshkov-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>,
David Woodhouse <dwmw2-wEGCiKHe2LqWVfeAwA7xHQ@public.gmane.org>,
Laurentiu Palcu
<laurentiu.palcu-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>,
Krzysztof Kozlowski
<k.kozlowski-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
Cc: Ramakrishna Pallala
<ramakrishna.pallala-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>,
linux-pm-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
Andreas Dannenberg <dannenberg-l0cyMroinI0@public.gmane.org>
Subject: [PATCH v5 09/11] power: bq24257: Allow input current limit sysfs access
Date: Fri, 18 Sep 2015 16:39:57 -0500 [thread overview]
Message-ID: <1442612399-341-10-git-send-email-dannenberg@ti.com> (raw)
In-Reply-To: <1442612399-341-1-git-send-email-dannenberg-l0cyMroinI0@public.gmane.org>
This patch allows reading (and writing, if the D+/D- USB signal-based
charger type detection is disabled) of the input current limit through
the power supply's input_current_limit sysfs property. This allows
userspace to see what charger was detected and to re-configure the
maximum current drawn from the external supply at runtime based on
system-level knowledge or user input.
Signed-off-by: Andreas Dannenberg <dannenberg-l0cyMroinI0@public.gmane.org>
---
drivers/power/bq24257_charger.c | 67 +++++++++++++++++++++++++++++++++++++++++
1 file changed, 67 insertions(+)
diff --git a/drivers/power/bq24257_charger.c b/drivers/power/bq24257_charger.c
index 615624c..66867d5 100644
--- a/drivers/power/bq24257_charger.c
+++ b/drivers/power/bq24257_charger.c
@@ -269,6 +269,42 @@ enum bq24257_fault {
FAULT_INPUT_LDO_LOW,
};
+static int bq24257_get_input_current_limit(struct bq24257_device *bq,
+ union power_supply_propval *val)
+{
+ int ret;
+
+ ret = bq24257_field_read(bq, F_IILIMIT);
+ if (ret < 0)
+ return ret;
+
+ /*
+ * The "External ILIM" and "Production & Test" modes are not exposed
+ * through this driver and not being covered by the lookup table.
+ * Should such a mode have become active let's return an error rather
+ * than exceeding the bounds of the lookup table and returning
+ * garbage.
+ */
+ if (ret >= BQ24257_IILIMIT_MAP_SIZE)
+ return -ENODATA;
+
+ val->intval = bq24257_iilimit_map[ret];
+
+ return 0;
+}
+
+static int bq24257_set_input_current_limit(struct bq24257_device *bq,
+ const union power_supply_propval *val)
+{
+ if (bq->iilimit_autoset_enable)
+ return -EPERM;
+
+ return bq24257_field_write(bq, F_IILIMIT,
+ bq24257_find_idx(val->intval,
+ bq24257_iilimit_map,
+ BQ24257_IILIMIT_MAP_SIZE));
+}
+
static int bq24257_power_supply_get_property(struct power_supply *psy,
enum power_supply_property psp,
union power_supply_propval *val)
@@ -353,6 +389,9 @@ static int bq24257_power_supply_get_property(struct power_supply *psy,
val->intval = bq24257_iterm_map[bq->init_data.iterm];
break;
+ case POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT:
+ return bq24257_get_input_current_limit(bq, val);
+
default:
return -EINVAL;
}
@@ -360,6 +399,31 @@ static int bq24257_power_supply_get_property(struct power_supply *psy,
return 0;
}
+static int bq24257_power_supply_set_property(struct power_supply *psy,
+ enum power_supply_property prop,
+ const union power_supply_propval *val)
+{
+ struct bq24257_device *bq = power_supply_get_drvdata(psy);
+
+ switch (prop) {
+ case POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT:
+ return bq24257_set_input_current_limit(bq, val);
+ default:
+ return -EINVAL;
+ }
+}
+
+static int bq24257_power_supply_property_is_writeable(struct power_supply *psy,
+ enum power_supply_property psp)
+{
+ switch (psp) {
+ case POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT:
+ return true;
+ default:
+ return false;
+ }
+}
+
static int bq24257_get_chip_state(struct bq24257_device *bq,
struct bq24257_state *state)
{
@@ -694,6 +758,7 @@ static enum power_supply_property bq24257_power_supply_props[] = {
POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE,
POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE_MAX,
POWER_SUPPLY_PROP_CHARGE_TERM_CURRENT,
+ POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT,
};
static char *bq24257_charger_supplied_to[] = {
@@ -706,6 +771,8 @@ static const struct power_supply_desc bq24257_power_supply_desc = {
.properties = bq24257_power_supply_props,
.num_properties = ARRAY_SIZE(bq24257_power_supply_props),
.get_property = bq24257_power_supply_get_property,
+ .set_property = bq24257_power_supply_set_property,
+ .property_is_writeable = bq24257_power_supply_property_is_writeable,
};
static ssize_t bq24257_show_ovp_voltage(struct device *dev,
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
next prev parent reply other threads:[~2015-09-18 21:39 UTC|newest]
Thread overview: 30+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-09-18 21:39 [PATCH v5 00/11] power: bq24257: Add support for bq24250/bq24251 Andreas Dannenberg
2015-09-18 21:39 ` [PATCH v5 01/11] dt: power: bq24257-charger: Cover additional devices Andreas Dannenberg
2015-09-22 16:24 ` Sebastian Reichel
2015-09-22 21:58 ` Andreas Dannenberg
2015-09-23 0:34 ` Sebastian Reichel
2015-09-23 8:14 ` Laurentiu Palcu
2015-09-23 14:13 ` Andreas Dannenberg
2015-09-18 21:39 ` [PATCH v5 02/11] power: bq24257: Add basic support for bq24250/bq24251 Andreas Dannenberg
2015-09-18 21:39 ` [PATCH v5 03/11] power: bq24257: Add bit definition for temp sense enable Andreas Dannenberg
2015-09-18 21:39 ` [PATCH v5 04/11] power: bq24257: Allow manual setting of input current limit Andreas Dannenberg
2015-09-18 21:39 ` [PATCH v5 06/11] power: bq24257: Use managed power supply register Andreas Dannenberg
2015-09-18 21:39 ` [PATCH v5 07/11] power: bq24257: Add over voltage protection setting support Andreas Dannenberg
2015-09-18 21:39 ` [PATCH v5 08/11] power: bq24257: Add input DPM voltage threshold " Andreas Dannenberg
[not found] ` <1442612399-341-1-git-send-email-dannenberg-l0cyMroinI0@public.gmane.org>
2015-09-18 21:39 ` [PATCH v5 05/11] power: bq24257: Add SW-based approach for Power Good determination Andreas Dannenberg
2015-09-22 19:37 ` Sebastian Reichel
2015-09-23 19:34 ` Andreas Dannenberg
2015-09-23 20:02 ` Andreas Dannenberg
2015-09-18 21:39 ` Andreas Dannenberg [this message]
2015-09-22 19:16 ` [PATCH v5 09/11] power: bq24257: Allow input current limit sysfs access Sebastian Reichel
2015-09-22 22:10 ` Andreas Dannenberg
2015-09-23 0:29 ` Sebastian Reichel
2015-09-23 14:11 ` Andreas Dannenberg
2015-09-23 15:02 ` Sebastian Reichel
2015-09-23 18:32 ` Andreas Dannenberg
2015-09-23 18:53 ` Sebastian Reichel
2015-09-23 19:47 ` Andreas Dannenberg
2015-09-18 21:39 ` [PATCH v5 10/11] power: bq24257: Add various device-specific sysfs properties Andreas Dannenberg
2015-09-18 21:39 ` [PATCH v5 11/11] power: bq24257: Add platform data based initialization Andreas Dannenberg
2015-09-22 19:29 ` Sebastian Reichel
2015-09-22 19:31 ` [PATCH v5 00/11] power: bq24257: Add support for bq24250/bq24251 Sebastian Reichel
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1442612399-341-10-git-send-email-dannenberg@ti.com \
--to=dannenberg-l0cymroini0@public.gmane.org \
--cc=dbaryshkov-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org \
--cc=devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=dwmw2-wEGCiKHe2LqWVfeAwA7xHQ@public.gmane.org \
--cc=k.kozlowski-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org \
--cc=laurentiu.palcu-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org \
--cc=linux-pm-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=ramakrishna.pallala-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org \
--cc=sre-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).