[PATCH v5 05/11] power: bq24257: Add SW-based approach for Power Good determination

[Andreas Dannenberg <dannenberg-l0cyMroinI0@public.gmane.org>]

A software-based approach for determining the charger's input voltage
"Power Good" state is introduced for devices like the bq24250 which
don't have a dedicated hardware pin for that purpose. This SW-based
approach is also used for other devices (with dedicated PG pin) as a
fall back solution if that pin is not configured to be used through
"pg-gpios".

Signed-off-by: Andreas Dannenberg <dannenberg-l0cyMroinI0@public.gmane.org>
---
 drivers/power/bq24257_charger.c | 49 ++++++++++++++++++++++++++++++++++++-----
 1 file changed, 43 insertions(+), 6 deletions(-)

diff --git a/drivers/power/bq24257_charger.c b/drivers/power/bq24257_charger.c
index 502dd8a5..135cfd4 100644
--- a/drivers/power/bq24257_charger.c
+++ b/drivers/power/bq24257_charger.c
@@ -107,6 +107,7 @@ struct bq24257_device {
 	struct mutex lock; /* protect state data */
 
 	bool iilimit_autoset_enable;
+	bool pg_gpio_disable;
 };
 
 static bool bq24257_is_volatile_reg(struct device *dev, unsigned int reg)
@@ -360,7 +361,26 @@ static int bq24257_get_chip_state(struct bq24257_device *bq,
 
 	state->fault = ret;
 
-	state->power_good = !gpiod_get_value_cansleep(bq->pg);
+	if (bq->pg_gpio_disable)
+		/*
+		 * If we have a chip without a dedicated power-good GPIO or
+		 * some other explicit bit that would provide this information
+		 * assume the power is good if there is no supply related
+		 * fault - and not good otherwise. There is a possibility for
+		 * other errors to mask that power in fact is not good but this
+		 * is probably the best we can do here.
+		 */
+		switch (state->fault) {
+		case FAULT_INPUT_OVP:
+		case FAULT_INPUT_UVLO:
+		case FAULT_INPUT_LDO_LOW:
+			state->power_good = false;
+			break;
+		default:
+			state->power_good = true;
+		}
+	else
+		state->power_good = !gpiod_get_value_cansleep(bq->pg);
 
 	return 0;
 }
@@ -680,7 +700,7 @@ static int bq24257_pg_gpio_probe(struct bq24257_device *bq)
 {
 	bq->pg = devm_gpiod_get_index(bq->dev, BQ24257_PG_GPIO, 0, GPIOD_IN);
 	if (IS_ERR(bq->pg)) {
-		dev_err(bq->dev, "could not probe PG pin\n");
+		dev_info(bq->dev, "could not probe PG pin\n");
 		return PTR_ERR(bq->pg);
 	}
 
@@ -814,10 +834,27 @@ static int bq24257_probe(struct i2c_client *client,
 		INIT_DELAYED_WORK(&bq->iilimit_setup_work,
 				  bq24257_iilimit_setup_work);
 
-	/* we can only check Power Good status by probing the PG pin */
-	ret = bq24257_pg_gpio_probe(bq);
-	if (ret < 0)
-		return ret;
+	/*
+	 * The BQ24250 doesn't have a dedicated Power Good (PG) pin so we
+	 * explicitly disable this feature for this device and instead use
+	 * a SW-based approach to determine the PG state.
+	 */
+	if (bq->chip == BQ24250)
+		bq->pg_gpio_disable = true;
+
+	/*
+	 * For devices that do have a dedicated PG pin go ahead and probe it,
+	 * using the SW-based approach as a fall back solution. Note that the
+	 * use of the dedicated pin is preferred.
+	 */
+	if (!bq->pg_gpio_disable) {
+		ret = bq24257_pg_gpio_probe(bq);
+		if (ret < 0) {
+			dev_info(bq->dev,
+				 "using SW-based power-good detection\n");
+			bq->pg_gpio_disable = true;
+		}
+	}
 
 	/* reset all registers to defaults */
 	ret = bq24257_field_write(bq, F_RESET, 1);
-- 
1.9.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html