From: Ray Jui <rjui@broadcom.com>
To: Florian Fainelli <f.fainelli@gmail.com>,
Rob Herring <robh+dt@kernel.org>, Arnd Bergmann <arnd@arndb.de>
Cc: Mark Rutland <mark.rutland@arm.com>,
devicetree@vger.kernel.org, Pawel Moll <pawel.moll@arm.com>,
Ian Campbell <ijc+devicetree@hellion.org.uk>,
Ray Jui <rjui@broadcom.com>,
linux-kernel@vger.kernel.org,
bcm-kernel-feedback-list@broadcom.com,
Kumar Gala <galak@codeaurora.org>,
linux-arm-kernel@lists.infradead.org
Subject: [PATCH v3 4/9] ARM: dts: Move all Cygnus peripherals into axi bus
Date: Mon, 21 Sep 2015 15:12:45 -0700 [thread overview]
Message-ID: <1442873570-20947-5-git-send-email-rjui@broadcom.com> (raw)
In-Reply-To: <1442873570-20947-1-git-send-email-rjui@broadcom.com>
Move all Cygnus peripherals to be under the "axi" bus node of type
"simple-bus"
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
---
arch/arm/boot/dts/bcm-cygnus.dtsi | 279 +++++++++++++++++++-------------------
1 file changed, 140 insertions(+), 139 deletions(-)
diff --git a/arch/arm/boot/dts/bcm-cygnus.dtsi b/arch/arm/boot/dts/bcm-cygnus.dtsi
index 97fd305..5ee7543 100644
--- a/arch/arm/boot/dts/bcm-cygnus.dtsi
+++ b/arch/arm/boot/dts/bcm-cygnus.dtsi
@@ -88,173 +88,174 @@
};
};
- pinctrl: pinctrl@0x0301d0c8 {
- compatible = "brcm,cygnus-pinmux";
- reg = <0x0301d0c8 0x30>,
- <0x0301d24c 0x2c>;
- };
+ axi {
+ compatible = "simple-bus";
+ ranges;
+ #address-cells = <1>;
+ #size-cells = <1>;
- gpio_crmu: gpio@03024800 {
- compatible = "brcm,cygnus-crmu-gpio";
- reg = <0x03024800 0x50>,
- <0x03024008 0x18>;
- #gpio-cells = <2>;
- gpio-controller;
- };
+ pinctrl: pinctrl@0x0301d0c8 {
+ compatible = "brcm,cygnus-pinmux";
+ reg = <0x0301d0c8 0x30>,
+ <0x0301d24c 0x2c>;
+ };
- gpio_ccm: gpio@1800a000 {
- compatible = "brcm,cygnus-ccm-gpio";
- reg = <0x1800a000 0x50>,
- <0x0301d164 0x20>;
- #gpio-cells = <2>;
- gpio-controller;
- interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-controller;
- };
+ gpio_crmu: gpio@03024800 {
+ compatible = "brcm,cygnus-crmu-gpio";
+ reg = <0x03024800 0x50>,
+ <0x03024008 0x18>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ };
- gpio_asiu: gpio@180a5000 {
- compatible = "brcm,cygnus-asiu-gpio";
- reg = <0x180a5000 0x668>;
- #gpio-cells = <2>;
- gpio-controller;
+ gpio_ccm: gpio@1800a000 {
+ compatible = "brcm,cygnus-ccm-gpio";
+ reg = <0x1800a000 0x50>,
+ <0x0301d164 0x20>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ };
- pinmux = <&pinctrl>;
+ gpio_asiu: gpio@180a5000 {
+ compatible = "brcm,cygnus-asiu-gpio";
+ reg = <0x180a5000 0x668>;
+ #gpio-cells = <2>;
+ gpio-controller;
- interrupt-controller;
- interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
- };
+ pinmux = <&pinctrl>;
- amba {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "arm,amba-bus", "simple-bus";
- interrupt-parent = <&gic>;
- ranges;
+ interrupt-controller;
+ interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
+ };
- wdt@18009000 {
- compatible = "arm,sp805" , "arm,primecell";
- reg = <0x18009000 0x1000>;
- interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&axi81_clk>;
- clock-names = "apb_pclk";
+ wdt0: wdt@18009000 {
+ compatible = "arm,sp805" , "arm,primecell";
+ reg = <0x18009000 0x1000>;
+ interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&axi81_clk>;
+ clock-names = "apb_pclk";
};
- };
- i2c0: i2c@18008000 {
- compatible = "brcm,cygnus-iproc-i2c", "brcm,iproc-i2c";
- reg = <0x18008000 0x100>;
- #address-cells = <1>;
- #size-cells = <0>;
- interrupts = <GIC_SPI 85 IRQ_TYPE_NONE>;
- clock-frequency = <100000>;
- status = "disabled";
- };
+ i2c0: i2c@18008000 {
+ compatible = "brcm,cygnus-iproc-i2c", "brcm,iproc-i2c";
+ reg = <0x18008000 0x100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 85 IRQ_TYPE_NONE>;
+ clock-frequency = <100000>;
+ status = "disabled";
+ };
- i2c1: i2c@1800b000 {
- compatible = "brcm,cygnus-iproc-i2c", "brcm,iproc-i2c";
- reg = <0x1800b000 0x100>;
- #address-cells = <1>;
- #size-cells = <0>;
- interrupts = <GIC_SPI 86 IRQ_TYPE_NONE>;
- clock-frequency = <100000>;
- status = "disabled";
- };
+ i2c1: i2c@1800b000 {
+ compatible = "brcm,cygnus-iproc-i2c", "brcm,iproc-i2c";
+ reg = <0x1800b000 0x100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 86 IRQ_TYPE_NONE>;
+ clock-frequency = <100000>;
+ status = "disabled";
+ };
- pcie0: pcie@18012000 {
- compatible = "brcm,iproc-pcie";
- reg = <0x18012000 0x1000>;
+ pcie0: pcie@18012000 {
+ compatible = "brcm,iproc-pcie";
+ reg = <0x18012000 0x1000>;
- #interrupt-cells = <1>;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &gic GIC_SPI 100 IRQ_TYPE_NONE>;
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &gic GIC_SPI 100 IRQ_TYPE_NONE>;
- linux,pci-domain = <0>;
+ linux,pci-domain = <0>;
- bus-range = <0x00 0xff>;
+ bus-range = <0x00 0xff>;
- #address-cells = <3>;
- #size-cells = <2>;
- device_type = "pci";
- ranges = <0x81000000 0 0 0x28000000 0 0x00010000
- 0x82000000 0 0x20000000 0x20000000 0 0x04000000>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ ranges = <0x81000000 0 0 0x28000000 0 0x00010000
+ 0x82000000 0 0x20000000 0x20000000 0 0x04000000>;
- status = "disabled";
- };
+ status = "disabled";
+ };
- pcie1: pcie@18013000 {
- compatible = "brcm,iproc-pcie";
- reg = <0x18013000 0x1000>;
+ pcie1: pcie@18013000 {
+ compatible = "brcm,iproc-pcie";
+ reg = <0x18013000 0x1000>;
- #interrupt-cells = <1>;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &gic GIC_SPI 106 IRQ_TYPE_NONE>;
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &gic GIC_SPI 106 IRQ_TYPE_NONE>;
- linux,pci-domain = <1>;
+ linux,pci-domain = <1>;
- bus-range = <0x00 0xff>;
+ bus-range = <0x00 0xff>;
- #address-cells = <3>;
- #size-cells = <2>;
- device_type = "pci";
- ranges = <0x81000000 0 0 0x48000000 0 0x00010000
- 0x82000000 0 0x40000000 0x40000000 0 0x04000000>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ ranges = <0x81000000 0 0 0x48000000 0 0x00010000
+ 0x82000000 0 0x40000000 0x40000000 0 0x04000000>;
- status = "disabled";
- };
+ status = "disabled";
+ };
- uart0: serial@18020000 {
- compatible = "snps,dw-apb-uart";
- reg = <0x18020000 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
- interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&axi81_clk>;
- clock-frequency = <100000000>;
- status = "disabled";
- };
+ uart0: serial@18020000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x18020000 0x100>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&axi81_clk>;
+ clock-frequency = <100000000>;
+ status = "disabled";
+ };
- uart1: serial@18021000 {
- compatible = "snps,dw-apb-uart";
- reg = <0x18021000 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
- interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&axi81_clk>;
- clock-frequency = <100000000>;
- status = "disabled";
- };
+ uart1: serial@18021000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x18021000 0x100>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&axi81_clk>;
+ clock-frequency = <100000000>;
+ status = "disabled";
+ };
- uart2: serial@18022000 {
- compatible = "snps,dw-apb-uart";
- reg = <0x18020000 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
- interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&axi81_clk>;
- clock-frequency = <100000000>;
- status = "disabled";
- };
+ uart2: serial@18022000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x18020000 0x100>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&axi81_clk>;
+ clock-frequency = <100000000>;
+ status = "disabled";
+ };
- uart3: serial@18023000 {
- compatible = "snps,dw-apb-uart";
- reg = <0x18023000 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
- interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&axi81_clk>;
- clock-frequency = <100000000>;
- status = "disabled";
- };
+ uart3: serial@18023000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x18023000 0x100>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&axi81_clk>;
+ clock-frequency = <100000000>;
+ status = "disabled";
+ };
- nand: nand@18046000 {
- compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1", "brcm,brcmnand";
- reg = <0x18046000 0x600>, <0xf8105408 0x600>, <0x18046f00 0x20>;
- reg-names = "nand", "iproc-idm", "iproc-ext";
- interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+ nand: nand@18046000 {
+ compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1",
+ "brcm,brcmnand";
+ reg = <0x18046000 0x600>, <0xf8105408 0x600>,
+ <0x18046f00 0x20>;
+ reg-names = "nand", "iproc-idm", "iproc-ext";
+ interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
- #address-cells = <1>;
- #size-cells = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
- brcm,nand-has-wp;
+ brcm,nand-has-wp;
+ };
};
};
--
1.9.1
next prev parent reply other threads:[~2015-09-21 22:12 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-09-21 22:12 [PATCH v3 0/9] Broadcom Cygnus device tree changes Ray Jui
2015-09-21 22:12 ` [PATCH v3 2/9] ARM: dts: Use label for device nodes in Cygnus dts Ray Jui
2015-09-21 22:12 ` [PATCH v3 3/9] ARM: dts: Put Cygnus core components under core bus Ray Jui
2015-09-21 22:12 ` Ray Jui [this message]
2015-09-21 22:12 ` [PATCH v3 5/9] ARM: dts: Reorder Cygnus peripherals Ray Jui
2015-09-21 22:12 ` [PATCH v3 6/9] ARM: dts: Enable various peripherals on bcm958305k Ray Jui
2015-09-21 22:12 ` [PATCH v3 7/9] ARM: dts: Enable NAND support on bcm911360_entphn Ray Jui
2015-09-21 22:12 ` [PATCH v3 9/9] ARM: dts: fix Cygnus nand device node Ray Jui
[not found] ` <1442873570-20947-1-git-send-email-rjui-dY08KVG/lbpWk0Htik3J/w@public.gmane.org>
2015-09-21 22:12 ` [PATCH v3 1/9] ARM: dts: consolidate aliases for Cygnus dt files Ray Jui
2015-09-21 22:12 ` [PATCH v3 8/9] ARM: dts: enable touchscreen support on Cygnus Ray Jui
2015-09-23 0:58 ` [PATCH v3 0/9] Broadcom Cygnus device tree changes Florian Fainelli
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1442873570-20947-5-git-send-email-rjui@broadcom.com \
--to=rjui@broadcom.com \
--cc=arnd@arndb.de \
--cc=bcm-kernel-feedback-list@broadcom.com \
--cc=devicetree@vger.kernel.org \
--cc=f.fainelli@gmail.com \
--cc=galak@codeaurora.org \
--cc=ijc+devicetree@hellion.org.uk \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=pawel.moll@arm.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).