[PATCH v8 1/7] ARM: dts: imx: imx7d-sbd remove fixed can2-3v3 regulator

[PATCH v8 1/7] ARM: dts: imx: imx7d-sbd remove fixed can2-3v3 regulator

[Adrian Alonso]

Remove incorrect can2-3v3 fixed regulator, imx7d-sdb doesn't
have a dedicated can2 fixed regulator instead it shares PERI_3V3
fixed regulator (RT8070ZS) which is enabled by default (hardwired)
from pmic pfuze3000 NVCC_3V3 power rail.

Signed-off-by: Adrian Alonso <aalonso@freescale.com>
---
Changes for V7: New patch in series
Changes for V8: Resend

 arch/arm/boot/dts/imx7d-sdb.dts | 11 +----------
 1 file changed, 1 insertion(+), 10 deletions(-)

diff --git a/arch/arm/boot/dts/imx7d-sdb.dts b/arch/arm/boot/dts/imx7d-sdb.dts
index 432aaf5..88308f3 100644
--- a/arch/arm/boot/dts/imx7d-sdb.dts
+++ b/arch/arm/boot/dts/imx7d-sdb.dts
@@ -78,16 +78,7 @@
 			enable-active-high;
 		};
 
-		reg_can2_3v3: regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "can2-3v3";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio1 7 GPIO_ACTIVE_LOW>;
-		};
-
-		reg_vref_1v8: regulator@3 {
+		reg_vref_1v8: regulator@2 {
 			compatible = "regulator-fixed";
 			reg = <3>;
 			regulator-name = "vref-1v8";
-- 
2.1.4

[PATCH v8 2/7] ARM: dts: imx: imx7d-sbd add iomuxc-lpsr hoggrp-2 pads

[Adrian Alonso]

Add imx7d-sdb iomuxc-lpsr hoggrp-2 default pads settings
Add iomuxc-lpsr usb_otg1_vbus pinctrl settings

Signed-off-by: Adrian Alonso <aalonso@freescale.com>
---
Changes for V2: Resend
Changes for V3: Resend
Changes for V4: Resend
Changes for V5: Resend
Changes for V6:
- Add wdog pinctrl group, add comments for hog2 group gpios
Changes for V7:
- Remove wdog pinctrl settings as they are not currently used
- Add pinctrl_usb_otg1_vbus settings
Changes for V8: Resend

 arch/arm/boot/dts/imx7d-sdb.dts | 21 +++++++++++++++++++++
 1 file changed, 21 insertions(+)

diff --git a/arch/arm/boot/dts/imx7d-sdb.dts b/arch/arm/boot/dts/imx7d-sdb.dts
index 88308f3..ca68a67 100644
--- a/arch/arm/boot/dts/imx7d-sdb.dts
+++ b/arch/arm/boot/dts/imx7d-sdb.dts
@@ -65,6 +65,8 @@
 			regulator-min-microvolt = <5000000>;
 			regulator-max-microvolt = <5000000>;
 			gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 =  <&pinctrl_usb_otg1_vbus>;
 			enable-active-high;
 		};
 
@@ -495,3 +497,22 @@
 
 	};
 };
+
+&iomuxc_lpsr {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog_2>;
+
+	imx7d-sdb {
+		pinctrl_hog_2: hog2grp {
+			fsl,pins = <
+				MX7D_PAD_GPIO1_IO07__GPIO1_IO7    0x59  /* sensor_int_b */
+			>;
+		};
+
+		pinctrl_usb_otg1_vbus: usbotg1vbusgrp {
+			fsl,pins = <
+				MX7D_PAD_GPIO1_IO05__GPIO1_IO5    0x14 	/* usb_otg1_pwr */
+			>;
+		};
+	};
+};
-- 
2.1.4

[PATCH v8 3/7] ARM: dts: imx: imx7d-sbd add usb_otg2_vbus pinctrl settings

[Adrian Alonso]

Add usb_otg2_vbus pinctrl settings

Signed-off-by: Adrian Alonso <aalonso@freescale.com>
---
Changes for V7: New patch in series
Changes for V8: Rework for latest master

 arch/arm/boot/dts/imx7d-sdb.dts | 9 ++++++++-
 1 file changed, 8 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/imx7d-sdb.dts b/arch/arm/boot/dts/imx7d-sdb.dts
index ca68a67..1962cb9 100644
--- a/arch/arm/boot/dts/imx7d-sdb.dts
+++ b/arch/arm/boot/dts/imx7d-sdb.dts
@@ -77,6 +77,8 @@
 			regulator-min-microvolt = <5000000>;
 			regulator-max-microvolt = <5000000>;
 			gpio = <&gpio4 7 GPIO_ACTIVE_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 =  <&pinctrl_usb_otg2_vbus>;
 			enable-active-high;
 		};
 
@@ -340,11 +342,16 @@
 
 		pinctrl_hog: hoggrp {
 			fsl,pins = <
-				MX7D_PAD_UART3_CTS_B__GPIO4_IO7		0x14
 				MX7D_PAD_ECSPI2_SS0__GPIO4_IO23		0x34  /* bt reg on */
 			>;
 		};
 
+		pinctrl_usb_otg2_vbus: usbotg2vbusgrp {
+			fsl,pins = <
+				MX7D_PAD_UART3_CTS_B__GPIO4_IO7		0x14 /* usb_otg2_pwr */
+			>;
+		};
+
 		pinctrl_i2c1: i2c1grp {
 			fsl,pins = <
 				MX7D_PAD_I2C1_SDA__I2C1_SDA		0x4000007f
-- 
2.1.4

[PATCH v8 4/7] pinctrl: freescale: imx: allow mux_reg offset zero

[Adrian Alonso]

Allow mux_reg offset zero to be a valid pin_id, on imx7d
mux_conf reg offset is zero for iomuxc-lspr controller

Signed-off-by: Adrian Alonso <aalonso@freescale.com>
---
Changes for V2: Resend
Changes for V3: Resend
Changes for V4: Simplify pin_id assigment when ZERO_OFFSET_VALID is set
Changes for V5:
- Drop patch pinctrl: freescale: imx: add ZERO_OFFSET_VALID flag
- Allow mux_reg ZERO OFFSET as pin_id
Changes for V6: Restore ZERO_OFFSET_VALID flag
Changes for V7: Resend
Changes for V8: Resend

 drivers/pinctrl/freescale/pinctrl-imx.c | 5 ++++-
 drivers/pinctrl/freescale/pinctrl-imx.h | 1 +
 2 files changed, 5 insertions(+), 1 deletion(-)

diff --git a/drivers/pinctrl/freescale/pinctrl-imx.c b/drivers/pinctrl/freescale/pinctrl-imx.c
index b9c6deb..151d50d 100644
--- a/drivers/pinctrl/freescale/pinctrl-imx.c
+++ b/drivers/pinctrl/freescale/pinctrl-imx.c
@@ -542,6 +542,9 @@ static int imx_pinctrl_parse_groups(struct device_node *np,
 		struct imx_pin_reg *pin_reg;
 		struct imx_pin *pin = &grp->pins[i];
 
+		if (!(info->flags & ZERO_OFFSET_VALID) && !mux_reg)
+			mux_reg = -1;
+
 		if (info->flags & SHARE_MUX_CONF_REG) {
 			conf_reg = mux_reg;
 		} else {
@@ -550,7 +553,7 @@ static int imx_pinctrl_parse_groups(struct device_node *np,
 				conf_reg = -1;
 		}
 
-		pin_id = mux_reg ? mux_reg / 4 : conf_reg / 4;
+		pin_id = (mux_reg != -1) ? mux_reg / 4 : conf_reg / 4;
 		pin_reg = &info->pin_regs[pin_id];
 		pin->pin = pin_id;
 		grp->pin_ids[i] = pin_id;
diff --git a/drivers/pinctrl/freescale/pinctrl-imx.h b/drivers/pinctrl/freescale/pinctrl-imx.h
index 2a5fe72..2a592f6 100644
--- a/drivers/pinctrl/freescale/pinctrl-imx.h
+++ b/drivers/pinctrl/freescale/pinctrl-imx.h
@@ -85,6 +85,7 @@ struct imx_pinctrl_soc_info {
 };
 
 #define SHARE_MUX_CONF_REG	0x1
+#define ZERO_OFFSET_VALID	0x2
 
 #define NO_MUX		0x0
 #define NO_PAD		0x0
-- 
2.1.4

[PATCH v8 5/7] pinctrl: freescale: imx: add shared input select reg support

[Adrian Alonso]

- Add shared input select register support
- imx7d has two iomux controllers iomuxc and iomuxc-lpsr
  which share select_input register for daisy chain settings

Signed-off-by: Adrian Alonso <aalonso@freescale.com>
---
Changes for V2: Resend
Changes for V3:
- Use of_parse_phandle instead of of_get_child_by_name to get input select
  base register address
Changes for V4: Resend
Changes for V5:
- Remove SHARE_INPUT_SELECT_REG flag
- Use fsl,input-sel to check if shared input select register support is used
Changes for V6: Resend
Changes for V7: Resend
Changes for V8: Resend

 drivers/pinctrl/freescale/pinctrl-imx.c | 28 +++++++++++++++++++++++++++-
 1 file changed, 27 insertions(+), 1 deletion(-)

diff --git a/drivers/pinctrl/freescale/pinctrl-imx.c b/drivers/pinctrl/freescale/pinctrl-imx.c
index 151d50d..a5bb939 100644
--- a/drivers/pinctrl/freescale/pinctrl-imx.c
+++ b/drivers/pinctrl/freescale/pinctrl-imx.c
@@ -18,6 +18,7 @@
 #include <linux/module.h>
 #include <linux/of.h>
 #include <linux/of_device.h>
+#include <linux/of_address.h>
 #include <linux/pinctrl/machine.h>
 #include <linux/pinctrl/pinconf.h>
 #include <linux/pinctrl/pinctrl.h>
@@ -39,6 +40,7 @@ struct imx_pinctrl {
 	struct device *dev;
 	struct pinctrl_dev *pctl;
 	void __iomem *base;
+	void __iomem *input_sel_base;
 	const struct imx_pinctrl_soc_info *info;
 };
 
@@ -254,7 +256,12 @@ static int imx_pmx_set(struct pinctrl_dev *pctldev, unsigned selector,
 			 * Regular select input register can never be at offset
 			 * 0, and we only print register value for regular case.
 			 */
-			writel(pin->input_val, ipctl->base + pin->input_reg);
+			if (ipctl->input_sel_base)
+				writel(pin->input_val, ipctl->input_sel_base +
+						pin->input_reg);
+			else
+				writel(pin->input_val, ipctl->base +
+						pin->input_reg);
 			dev_dbg(ipctl->dev,
 				"==>select_input: offset 0x%x val 0x%x\n",
 				pin->input_reg, pin->input_val);
@@ -685,6 +692,8 @@ static int imx_pinctrl_probe_dt(struct platform_device *pdev,
 int imx_pinctrl_probe(struct platform_device *pdev,
 		      struct imx_pinctrl_soc_info *info)
 {
+	struct device_node *dev_np = pdev->dev.of_node;
+	struct device_node *np;
 	struct imx_pinctrl *ipctl;
 	struct resource *res;
 	int ret, i;
@@ -715,6 +724,23 @@ int imx_pinctrl_probe(struct platform_device *pdev,
 	if (IS_ERR(ipctl->base))
 		return PTR_ERR(ipctl->base);
 
+	if (of_property_read_bool(dev_np, "fsl,input-sel")) {
+		np = of_parse_phandle(dev_np, "fsl,input-sel", 0);
+		if (np) {
+			ipctl->input_sel_base = of_iomap(np, 0);
+			if (IS_ERR(ipctl->input_sel_base)) {
+				of_node_put(np);
+				dev_err(&pdev->dev,
+					"iomuxc input select base address not found\n");
+				return PTR_ERR(ipctl->input_sel_base);
+			}
+		} else {
+			dev_err(&pdev->dev, "iomuxc fsl,input-sel property not found\n");
+			return -EINVAL;
+		}
+		of_node_put(np);
+	}
+
 	imx_pinctrl_desc.name = dev_name(&pdev->dev);
 	imx_pinctrl_desc.pins = info->pins;
 	imx_pinctrl_desc.npins = info->npins;
-- 
2.1.4

[PATCH v8 6/7] pinctrl: freescale: imx7d: support iomux lpsr controller

[Adrian Alonso]

iMX7D has two iomuxc controllers, iomuxc controller similar as
previous iMX SoC generation and iomuxc-lpsr which provides low
power state rentetion capabilities on gpios that are part of
iomuxc-lpsr

Add iomuxc-lpsr gpio group id's

Signed-off-by: Adrian Alonso <aalonso@freescale.com>
---
Changes for V2: Add imx7d_lpsr_pads enums
Changes for V3: Resend
Changes for V4: Resend
Changes for V5: Remove flags SHARE_INPUT_SELECT_REG and ZERO_OFFSET_VALID.
Changes for V6: Restore ZERO_OFFSET_VALID flag.
Changes for V7: Resend
Changes for V8: Resend

 drivers/pinctrl/freescale/pinctrl-imx7d.c | 30 ++++++++++++++++++++++++++++++
 1 file changed, 30 insertions(+)

diff --git a/drivers/pinctrl/freescale/pinctrl-imx7d.c b/drivers/pinctrl/freescale/pinctrl-imx7d.c
index 1fa7530..16dc925 100644
--- a/drivers/pinctrl/freescale/pinctrl-imx7d.c
+++ b/drivers/pinctrl/freescale/pinctrl-imx7d.c
@@ -174,6 +174,17 @@ enum imx7d_pads {
 	MX7D_PAD_ENET1_COL = 154,
 };
 
+enum imx7d_lpsr_pads {
+	MX7D_PAD_GPIO1_IO00 = 0,
+	MX7D_PAD_GPIO1_IO01 = 1,
+	MX7D_PAD_GPIO1_IO02 = 2,
+	MX7D_PAD_GPIO1_IO03 = 3,
+	MX7D_PAD_GPIO1_IO04 = 4,
+	MX7D_PAD_GPIO1_IO05 = 5,
+	MX7D_PAD_GPIO1_IO06 = 6,
+	MX7D_PAD_GPIO1_IO07 = 7,
+};
+
 /* Pad names for the pinmux subsystem */
 static const struct pinctrl_pin_desc imx7d_pinctrl_pads[] = {
 	IMX_PINCTRL_PIN(MX7D_PAD_RESERVE0),
@@ -333,13 +344,32 @@ static const struct pinctrl_pin_desc imx7d_pinctrl_pads[] = {
 	IMX_PINCTRL_PIN(MX7D_PAD_ENET1_COL),
 };
 
+/* Pad names for the pinmux subsystem */
+static const struct pinctrl_pin_desc imx7d_lpsr_pinctrl_pads[] = {
+	IMX_PINCTRL_PIN(MX7D_PAD_GPIO1_IO00),
+	IMX_PINCTRL_PIN(MX7D_PAD_GPIO1_IO01),
+	IMX_PINCTRL_PIN(MX7D_PAD_GPIO1_IO02),
+	IMX_PINCTRL_PIN(MX7D_PAD_GPIO1_IO03),
+	IMX_PINCTRL_PIN(MX7D_PAD_GPIO1_IO04),
+	IMX_PINCTRL_PIN(MX7D_PAD_GPIO1_IO05),
+	IMX_PINCTRL_PIN(MX7D_PAD_GPIO1_IO06),
+	IMX_PINCTRL_PIN(MX7D_PAD_GPIO1_IO07),
+};
+
 static struct imx_pinctrl_soc_info imx7d_pinctrl_info = {
 	.pins = imx7d_pinctrl_pads,
 	.npins = ARRAY_SIZE(imx7d_pinctrl_pads),
 };
 
+static struct imx_pinctrl_soc_info imx7d_lpsr_pinctrl_info = {
+	.pins = imx7d_lpsr_pinctrl_pads,
+	.npins = ARRAY_SIZE(imx7d_lpsr_pinctrl_pads),
+	.flags = ZERO_OFFSET_VALID,
+};
+
 static struct of_device_id imx7d_pinctrl_of_match[] = {
 	{ .compatible = "fsl,imx7d-iomuxc", .data = &imx7d_pinctrl_info, },
+	{ .compatible = "fsl,imx7d-iomuxc-lpsr", .data = &imx7d_lpsr_pinctrl_info },
 	{ /* sentinel */ }
 };
 
-- 
2.1.4

[PATCH v8 7/7] pinctrl: freescale: imx: imx7d iomuxc-lpsr devicetree bindings

[Adrian Alonso]

Add iomuxc-lpsr devicetree bindings documentation
Provide documentation context as well an example on
pheriperals that could use pad from either iomuxc controller
supported by iMX7D SoC

Signed-off-by: Adrian Alonso <aalonso@freescale.com>
---
Changes for V2: New patch on imx7d iomuxc-lpsr patch series
Changes for V3: Add shared input select register notes
Changes for V4: Resend
Changes for V5:
- Fix spell error
- Remove references of SHARE_INPUT_SELECT_REG flag
Changes for V6: Resend
Changes for V7: Resend
Changes for V8: Correct SDA pad example

 .../bindings/pinctrl/fsl,imx7d-pinctrl.txt         | 63 +++++++++++++++++++++-
 1 file changed, 62 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt
index 8bbf25d..457b2c6 100644
--- a/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt
@@ -1,16 +1,42 @@
 * Freescale i.MX7 Dual IOMUX Controller
 
+iMX7D supports two iomuxc controllers, fsl,imx7d-iomuxc controller is similar
+as previous iMX SoC generation and fsl,imx7d-iomuxc-lpsr which provides low
+power state retention capabilities on gpios that are part of iomuxc-lpsr
+(GPIO1_IO7..GPIO1_IO0). While iomuxc-lpsr provides its own set of registers for
+mux and pad control settings, it shares the input select register from main
+iomuxc controller for daisy chain settings, the fsl,input-sel property extends
+fsl,imx-pinctrl driver to support iomuxc-lpsr controller.
+
+iomuxc_lpsr: iomuxc-lpsr@302c0000 {
+	compatible = "fsl,imx7d-iomuxc-lpsr";
+	reg = <0x302c0000 0x10000>;
+	fsl,input-sel = <&iomuxc>;
+};
+
+iomuxc: iomuxc@30330000 {
+	compatible = "fsl,imx7d-iomuxc";
+	reg = <0x30330000 0x10000>;
+};
+
+Pheriparials using pads from iomuxc-lpsr support low state retention power
+state, under LPSR mode GPIO's state of pads are retain.
+
 Please refer to fsl,imx-pinctrl.txt in this directory for common binding part
 and usage.
 
 Required properties:
-- compatible: "fsl,imx7d-iomuxc"
+- compatible: "fsl,imx7d-iomuxc" for main IOMUXC controller, or
+  "fsl,imx7d-iomuxc-lpsr" for Low Power State Retention IOMUXC controller.
 - fsl,pins: each entry consists of 6 integers and represents the mux and config
   setting for one pin.  The first 5 integers <mux_reg conf_reg input_reg mux_val
   input_val> are specified using a PIN_FUNC_ID macro, which can be found in
   imx7d-pinfunc.h under device tree source folder.  The last integer CONFIG is
   the pad setting value like pull-up on this pin.  Please refer to i.MX7 Dual
   Reference Manual for detailed CONFIG settings.
+- fsl,input-sel: required property for iomuxc-lpsr controller, this property is
+  a phandle for main iomuxc controller which shares the input select register for
+  daisy chain settings.
 
 CONFIG bits definition:
 PAD_CTL_PUS_100K_DOWN           (0 << 5)
@@ -25,3 +51,38 @@ PAD_CTL_DSE_X1                  (0 << 0)
 PAD_CTL_DSE_X2                  (1 << 0)
 PAD_CTL_DSE_X3                  (2 << 0)
 PAD_CTL_DSE_X4                  (3 << 0)
+
+Examples:
+While iomuxc-lpsr is intended to be used by dedicated peripherals to take
+advantages of LPSR power mode, is also possible that an IP to use pads from
+any of the iomux controllers. For example the I2C1 IP can use SCL pad from
+iomuxc-lpsr controller and SDA pad from iomuxc controller as:
+
+i2c1: i2c@30a20000 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1_1 &pinctrl_i2c1_2>;
+	status = "okay";
+};
+
+iomuxc-lpsr@302c0000 {
+	compatible = "fsl,imx7d-iomuxc-lpsr";
+	reg = <0x302c0000 0x10000>;
+	fsl,input-sel = <&iomuxc>;
+
+	pinctrl_i2c1_1: i2c1grp-1 {
+		fsl,pins = <
+			MX7D_PAD_GPIO1_IO04__I2C1_SCL 0x4000007f
+		>;
+	};
+};
+
+iomuxc@30330000 {
+	compatible = "fsl,imx7d-iomuxc";
+	reg = <0x30330000 0x10000>;
+
+	pinctrl_i2c1_2: i2c1grp-2 {
+		fsl,pins = <
+			MX7D_PAD_I2C1_SDA__I2C1_SDA 0x4000007f
+		>;
+	};
+};
-- 
2.1.4

Re: [PATCH v8 4/7] pinctrl: freescale: imx: allow mux_reg offset zero

[Linus Walleij]

On Wed, Sep 30, 2015 at 9:11 AM, Adrian Alonso <aalonso@freescale.com> wrote:

> Allow mux_reg offset zero to be a valid pin_id, on imx7d
> mux_conf reg offset is zero for iomuxc-lspr controller
>
> Signed-off-by: Adrian Alonso <aalonso@freescale.com>
> ---
> Changes for V2: Resend
> Changes for V3: Resend
> Changes for V4: Simplify pin_id assigment when ZERO_OFFSET_VALID is set
> Changes for V5:
> - Drop patch pinctrl: freescale: imx: add ZERO_OFFSET_VALID flag
> - Allow mux_reg ZERO OFFSET as pin_id
> Changes for V6: Restore ZERO_OFFSET_VALID flag
> Changes for V7: Resend
> Changes for V8: Resend

Ugh patches come out quickly. I see this is identical to the
v6 I applied so keeping the applied version.

Yours,
Linus Walleij

Re: [PATCH v8 5/7] pinctrl: freescale: imx: add shared input select reg support

[Linus Walleij]

On Wed, Sep 30, 2015 at 9:11 AM, Adrian Alonso <aalonso@freescale.com> wrote:

> - Add shared input select register support
> - imx7d has two iomux controllers iomuxc and iomuxc-lpsr
>   which share select_input register for daisy chain settings
>
> Signed-off-by: Adrian Alonso <aalonso@freescale.com>
> ---
> Changes for V2: Resend
> Changes for V3:
> - Use of_parse_phandle instead of of_get_child_by_name to get input select
>   base register address
> Changes for V4: Resend
> Changes for V5:
> - Remove SHARE_INPUT_SELECT_REG flag
> - Use fsl,input-sel to check if shared input select register support is used
> Changes for V6: Resend
> Changes for V7: Resend
> Changes for V8: Resend

Also seem identical to what I applied for v6 so keeping that one.

Yours,
Linus Walleij

Re: [PATCH v8 6/7] pinctrl: freescale: imx7d: support iomux lpsr controller

[Linus Walleij]

On Wed, Sep 30, 2015 at 9:11 AM, Adrian Alonso <aalonso@freescale.com> wrote:

> iMX7D has two iomuxc controllers, iomuxc controller similar as
> previous iMX SoC generation and iomuxc-lpsr which provides low
> power state rentetion capabilities on gpios that are part of
> iomuxc-lpsr
>
> Add iomuxc-lpsr gpio group id's
>
> Signed-off-by: Adrian Alonso <aalonso@freescale.com>
> ---
> Changes for V2: Add imx7d_lpsr_pads enums
> Changes for V3: Resend
> Changes for V4: Resend
> Changes for V5: Remove flags SHARE_INPUT_SELECT_REG and ZERO_OFFSET_VALID.
> Changes for V6: Restore ZERO_OFFSET_VALID flag.
> Changes for V7: Resend
> Changes for V8: Resend

Patch applied with Shawn's ACK.

Yours,
Linus Walleij

Re: [PATCH v8 7/7] pinctrl: freescale: imx: imx7d iomuxc-lpsr devicetree bindings

[Linus Walleij]

On Wed, Sep 30, 2015 at 9:11 AM, Adrian Alonso <aalonso@freescale.com> wrote:

> Add iomuxc-lpsr devicetree bindings documentation
> Provide documentation context as well an example on
> pheriperals that could use pad from either iomuxc controller
> supported by iMX7D SoC
>
> Signed-off-by: Adrian Alonso <aalonso@freescale.com>
> ---
> Changes for V2: New patch on imx7d iomuxc-lpsr patch series
> Changes for V3: Add shared input select register notes
> Changes for V4: Resend
> Changes for V5:
> - Fix spell error
> - Remove references of SHARE_INPUT_SELECT_REG flag
> Changes for V6: Resend
> Changes for V7: Resend
> Changes for V8: Correct SDA pad example

Patch applied. Assuming Shawn's old ACK is valid so attached it,
else beat me up Shawn.

Yours,
Linus Walleij