* [PATCH v3 1/3] wlcore/wl12xx: spi: add power operation function
[not found] ` <1451304139-10899-1-git-send-email-uri.mashiach-UTxiZqZC01RS1MOuV/RT9w@public.gmane.org>
@ 2015-12-28 12:02 ` Uri Mashiach
2015-12-28 12:02 ` [PATCH v3 2/3] wlcore/wl12xx: spi: add device tree support Uri Mashiach
2015-12-28 12:02 ` [PATCH v3 3/3] wlcore/wl12xx: spi: add wifi support to cm-t335 Uri Mashiach
2 siblings, 0 replies; 5+ messages in thread
From: Uri Mashiach @ 2015-12-28 12:02 UTC (permalink / raw)
To: Kalle Valo, Rob Herring, Tony Lindgren
Cc: Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
bcousson-rdvid1DuHRBWk0Htik3J/w, Igor Grinberg, Eliad Peller,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-omap-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-wireless-u79uwXL29TY76Z2rM5mHXA, Uri Mashiach
The power function uses a consumer regulator access to update the WiFi
enable GPIO value.
Signed-off-by: Uri Mashiach <uri.mashiach-UTxiZqZC01RS1MOuV/RT9w@public.gmane.org>
---
v1 -> v2: oops fix was removed to a separate fix.
v2 -> v3: no changes
drivers/net/wireless/ti/wlcore/spi.c | 37 ++++++++++++++++++++++++++++++++++++
1 file changed, 37 insertions(+)
diff --git a/drivers/net/wireless/ti/wlcore/spi.c b/drivers/net/wireless/ti/wlcore/spi.c
index 44f059f..d3a4bcb 100644
--- a/drivers/net/wireless/ti/wlcore/spi.c
+++ b/drivers/net/wireless/ti/wlcore/spi.c
@@ -30,6 +30,7 @@
#include <linux/spi/spi.h>
#include <linux/wl12xx.h>
#include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
#include "wlcore.h"
#include "wl12xx_80211.h"
@@ -81,6 +82,7 @@
struct wl12xx_spi_glue {
struct device *dev;
struct platform_device *core;
+ struct regulator *reg; /* Power regulator */
};
static void wl12xx_spi_reset(struct device *child)
@@ -318,11 +320,40 @@ static int __must_check wl12xx_spi_raw_write(struct device *child, int addr,
return 0;
}
+/**
+ * wl12xx_spi_set_power - power on/off the wl12xx unit
+ * @child: wl12xx device handle.
+ * @enable: true/false to power on/off the unit.
+ *
+ * use the WiFi enable regulator to enable/disable the WiFi unit.
+ */
+static int wl12xx_spi_set_power(struct device *child, bool enable)
+{
+ int ret = 0;
+ struct wl12xx_spi_glue *glue = dev_get_drvdata(child->parent);
+
+ WARN_ON(!glue->reg);
+
+ /* Update regulator state */
+ if (enable) {
+ ret = regulator_enable(glue->reg);
+ if (ret)
+ dev_err(child, "Power enable failure\n");
+ } else {
+ ret = regulator_disable(glue->reg);
+ if (ret)
+ dev_err(child, "Power disable failure\n");
+ }
+
+ return ret;
+}
+
static struct wl1271_if_operations spi_ops = {
.read = wl12xx_spi_raw_read,
.write = wl12xx_spi_raw_write,
.reset = wl12xx_spi_reset,
.init = wl12xx_spi_init,
+ .power = wl12xx_spi_set_power,
.set_block_size = NULL,
};
@@ -353,6 +384,12 @@ static int wl1271_probe(struct spi_device *spi)
* comes from the board-peripherals file */
spi->bits_per_word = 32;
+ glue->reg = devm_regulator_get(&spi->dev, "vwlan");
+ if (IS_ERR(glue->reg)) {
+ dev_err(glue->dev, "can't get regulator\n");
+ return PTR_ERR(glue->reg);
+ }
+
ret = spi_setup(spi);
if (ret < 0) {
dev_err(glue->dev, "spi_setup failed\n");
--
2.5.0
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 5+ messages in thread* [PATCH v3 2/3] wlcore/wl12xx: spi: add device tree support
[not found] ` <1451304139-10899-1-git-send-email-uri.mashiach-UTxiZqZC01RS1MOuV/RT9w@public.gmane.org>
2015-12-28 12:02 ` [PATCH v3 1/3] wlcore/wl12xx: spi: add power operation function Uri Mashiach
@ 2015-12-28 12:02 ` Uri Mashiach
[not found] ` <1451304139-10899-3-git-send-email-uri.mashiach-UTxiZqZC01RS1MOuV/RT9w@public.gmane.org>
2015-12-28 12:02 ` [PATCH v3 3/3] wlcore/wl12xx: spi: add wifi support to cm-t335 Uri Mashiach
2 siblings, 1 reply; 5+ messages in thread
From: Uri Mashiach @ 2015-12-28 12:02 UTC (permalink / raw)
To: Kalle Valo, Rob Herring, Tony Lindgren
Cc: Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
bcousson-rdvid1DuHRBWk0Htik3J/w, Igor Grinberg, Eliad Peller,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-omap-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-wireless-u79uwXL29TY76Z2rM5mHXA, Uri Mashiach
Add DT support for the wl1271 SPI WiFi.
Add documentation file for the wl1271 SPI WiFi.
Signed-off-by: Uri Mashiach <uri.mashiach-UTxiZqZC01RS1MOuV/RT9w@public.gmane.org>
Acked-by: Igor Grinberg <grinberg-UTxiZqZC01RS1MOuV/RT9w@public.gmane.org>
---
v1 -> v2: update interrupt documentation.
replace interrupts and interrupt-parent with interrupts-extended.
IRQ parameters retrieved from spi_device instead of DT.
remove redundant #ifdef CONFIG_OF
v2 -> v3: Add MODULE_DEVICE_TABLE.
Remove #ifdef CONFIG_OF.
Make the Kconfig symbol to depend on OF.
Replace irqd_get_trigger_type() with irq_get_trigger_type().
.../bindings/net/wireless/ti,wlcore,spi.txt | 34 ++++++++++++++++
drivers/net/wireless/ti/wlcore/Kconfig | 2 +-
drivers/net/wireless/ti/wlcore/spi.c | 47 ++++++++++++++++++++--
3 files changed, 78 insertions(+), 5 deletions(-)
create mode 100644 Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt
diff --git a/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt b/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt
new file mode 100644
index 0000000..502c27e
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt
@@ -0,0 +1,34 @@
+* Texas Instruments wl1271 wireless lan controller
+
+The wl1271 chip can be connected via SPI or via SDIO. This
+document describes the binding for the SPI connected chip.
+
+Required properties:
+- compatible : Should be "ti,wl1271"
+- reg : Chip select address of device
+- spi-max-frequency : Maximum SPI clocking speed of device in Hz
+- ref-clock-frequency : Reference clock frequency
+- interrupts-extended : Should contain parameters for 1 interrupt line.
+ Interrupt parameters: parent, line number, type.
+- vwlan-supply : Point the node of the regulator that powers/enable the wl1271 chip
+
+Optional properties:
+- clock-xtal : boolean, clock is generated from XTAL
+
+- Please consult Documentation/devicetree/bindings/spi/spi-bus.txt
+ for optional SPI connection related properties,
+
+Examples:
+
+&spi1 {
+ wl1271@1 {
+ compatible = "ti,wl1271";
+
+ reg = <1>;
+ spi-max-frequency = <48000000>;
+ clock-xtal;
+ ref-clock-frequency = <38400000>;
+ interrupts-extended = <&gpio3 8 IRQ_TYPE_LEVEL_HIGH>;
+ vwlan-supply = <&vwlan_fixed>;
+ };
+};
diff --git a/drivers/net/wireless/ti/wlcore/Kconfig b/drivers/net/wireless/ti/wlcore/Kconfig
index 7c09954..5918080 100644
--- a/drivers/net/wireless/ti/wlcore/Kconfig
+++ b/drivers/net/wireless/ti/wlcore/Kconfig
@@ -13,7 +13,7 @@ config WLCORE
config WLCORE_SPI
tristate "TI wlcore SPI support"
- depends on WLCORE && SPI_MASTER
+ depends on WLCORE && SPI_MASTER && OF
select CRC7
---help---
This module adds support for the SPI interface of adapters using
diff --git a/drivers/net/wireless/ti/wlcore/spi.c b/drivers/net/wireless/ti/wlcore/spi.c
index d3a4bcb..0f2fb50 100644
--- a/drivers/net/wireless/ti/wlcore/spi.c
+++ b/drivers/net/wireless/ti/wlcore/spi.c
@@ -30,6 +30,7 @@
#include <linux/spi/spi.h>
#include <linux/wl12xx.h>
#include <linux/platform_device.h>
+#include <linux/of_irq.h>
#include <linux/regulator/consumer.h>
#include "wlcore.h"
@@ -357,6 +358,39 @@ static struct wl1271_if_operations spi_ops = {
.set_block_size = NULL,
};
+static const struct of_device_id wlcore_spi_of_match_table[] = {
+ { .compatible = "ti,wl1271" },
+ { }
+};
+MODULE_DEVICE_TABLE(of, wlcore_spi_of_match_table);
+
+/**
+ * wlcore_probe_of - DT node parsing.
+ * @spi: SPI slave device parameters.
+ * @res: resource parameters.
+ * @glue: wl12xx SPI bus to slave device glue parameters.
+ * @pdev_data: wlcore device parameters
+ */
+static int wlcore_probe_of(struct spi_device *spi, struct wl12xx_spi_glue *glue,
+ struct wlcore_platdev_data *pdev_data)
+{
+ struct device_node *dt_node = spi->dev.of_node;
+ int ret;
+
+ if (of_find_property(dt_node, "clock-xtal", NULL))
+ pdev_data->ref_clock_xtal = true;
+
+ ret = of_property_read_u32(dt_node, "ref-clock-frequency",
+ &pdev_data->ref_clock_freq);
+ if (IS_ERR_VALUE(ret)) {
+ dev_err(glue->dev,
+ "can't get reference clock frequency (%d)\n", ret);
+ return ret;
+ }
+
+ return 0;
+}
+
static int wl1271_probe(struct spi_device *spi)
{
struct wl12xx_spi_glue *glue;
@@ -366,8 +400,6 @@ static int wl1271_probe(struct spi_device *spi)
memset(&pdev_data, 0x00, sizeof(pdev_data));
- /* TODO: add DT parsing when needed */
-
pdev_data.if_ops = &spi_ops;
glue = devm_kzalloc(&spi->dev, sizeof(*glue), GFP_KERNEL);
@@ -390,6 +422,13 @@ static int wl1271_probe(struct spi_device *spi)
return PTR_ERR(glue->reg);
}
+ ret = wlcore_probe_of(spi, glue, &pdev_data);
+ if (IS_ERR_VALUE(ret)) {
+ dev_err(glue->dev,
+ "can't get device tree parameters (%d)\n", ret);
+ return ret;
+ }
+
ret = spi_setup(spi);
if (ret < 0) {
dev_err(glue->dev, "spi_setup failed\n");
@@ -407,7 +446,7 @@ static int wl1271_probe(struct spi_device *spi)
memset(res, 0x00, sizeof(res));
res[0].start = spi->irq;
- res[0].flags = IORESOURCE_IRQ;
+ res[0].flags = IORESOURCE_IRQ | irq_get_trigger_type(spi->irq);
res[0].name = "irq";
ret = platform_device_add_resources(glue->core, res, ARRAY_SIZE(res));
@@ -445,10 +484,10 @@ static int wl1271_remove(struct spi_device *spi)
return 0;
}
-
static struct spi_driver wl1271_spi_driver = {
.driver = {
.name = "wl1271_spi",
+ .of_match_table = of_match_ptr(wlcore_spi_of_match_table),
},
.probe = wl1271_probe,
--
2.5.0
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 5+ messages in thread* [PATCH v3 3/3] wlcore/wl12xx: spi: add wifi support to cm-t335
[not found] ` <1451304139-10899-1-git-send-email-uri.mashiach-UTxiZqZC01RS1MOuV/RT9w@public.gmane.org>
2015-12-28 12:02 ` [PATCH v3 1/3] wlcore/wl12xx: spi: add power operation function Uri Mashiach
2015-12-28 12:02 ` [PATCH v3 2/3] wlcore/wl12xx: spi: add device tree support Uri Mashiach
@ 2015-12-28 12:02 ` Uri Mashiach
2 siblings, 0 replies; 5+ messages in thread
From: Uri Mashiach @ 2015-12-28 12:02 UTC (permalink / raw)
To: Kalle Valo, Rob Herring, Tony Lindgren
Cc: Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
bcousson-rdvid1DuHRBWk0Htik3J/w, Igor Grinberg, Eliad Peller,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-omap-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-wireless-u79uwXL29TY76Z2rM5mHXA, Uri Mashiach
Device tree modifications:
- Pinmux for SPI0 and WiFi GPIOs.
- SPI0 node with wlcore as a child node.
Cc: Tony Lindgren <tony-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org>
Signed-off-by: Uri Mashiach <uri.mashiach-UTxiZqZC01RS1MOuV/RT9w@public.gmane.org>
Acked-by: Igor Grinberg <grinberg-lB3UumIvzKrRNpEZXGUFxA@public.gmane.org>
---
v1 -> v2: Replace interrupts and interrupt-parent with interrupts-extended.
v2 -> v3: Move the pinctrl-0 = <&wifi_pins> to the wlcore node.
arch/arm/boot/dts/am335x-cm-t335.dts | 54 ++++++++++++++++++++++++++++++++++++
1 file changed, 54 insertions(+)
diff --git a/arch/arm/boot/dts/am335x-cm-t335.dts b/arch/arm/boot/dts/am335x-cm-t335.dts
index 42e9b66..b700940 100644
--- a/arch/arm/boot/dts/am335x-cm-t335.dts
+++ b/arch/arm/boot/dts/am335x-cm-t335.dts
@@ -11,6 +11,7 @@
/dts-v1/;
#include "am33xx.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
/ {
model = "CompuLab CM-T335";
@@ -40,6 +41,15 @@
regulator-max-microvolt = <3300000>;
};
+ /* Regulator for WiFi */
+ vwlan_fixed: fixedregulator@2 {
+ compatible = "regulator-fixed";
+ regulator-name = "vwlan_fixed";
+ gpio = <&gpio0 20 GPIO_ACTIVE_HIGH>; /* gpio0_20 */
+ enable-active-high;
+ regulator-boot-off;
+ };
+
backlight {
compatible = "pwm-backlight";
pwms = <&ecap0 0 50000 0>;
@@ -223,6 +233,21 @@
>;
};
+ spi0_pins: pinmux_spi0_pins {
+ pinctrl-single,pins = <
+ /* spi0_sclk.spi0_sclk */
+ AM33XX_IOPAD(0x950, PIN_INPUT | MUX_MODE0)
+ /* spi0_d0.spi0_d0 */
+ AM33XX_IOPAD(0x954, PIN_OUTPUT_PULLUP | MUX_MODE0)
+ /* spi0_d1.spi0_d1 */
+ AM33XX_IOPAD(0x958, PIN_INPUT | MUX_MODE0)
+ /* spi0_cs0.spi0_cs0 */
+ AM33XX_IOPAD(0x95C, PIN_OUTPUT | MUX_MODE0)
+ /* spi0_cs1.spi0_cs1 */
+ AM33XX_IOPAD(0x960, PIN_OUTPUT | MUX_MODE0)
+ >;
+ };
+
/* wl1271 bluetooth */
bluetooth_pins: pinmux_bluetooth_pins {
pinctrl-single,pins = <
@@ -230,6 +255,16 @@
AM33XX_IOPAD(0x9b0, PIN_OUTPUT_PULLUP | MUX_MODE7)
>;
};
+
+ /* wl1271 WiFi */
+ wifi_pins: pinmux_wifi_pins {
+ pinctrl-single,pins = <
+ /* EMU1.gpio3_8 - WiFi IRQ */
+ AM33XX_IOPAD(0x9e8, PIN_INPUT_PULLUP | MUX_MODE7)
+ /* XDMA_EVENT_INTR1.gpio0_20 - WiFi enable */
+ AM33XX_IOPAD(0x9b4, PIN_OUTPUT | MUX_MODE7)
+ >;
+ };
};
&uart0 {
@@ -394,3 +429,22 @@ status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&mmc1_pins>;
};
+
+&spi0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_pins>;
+ ti,pindir-d0-out-d1-in = <1>;
+ /* WLS1271 WiFi */
+ wlcore: wlcore@1 {
+ compatible = "ti,wl1271";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_pins>;
+ reg = <1>;
+ spi-max-frequency = <48000000>;
+ clock-xtal;
+ ref-clock-frequency = <38400000>;
+ interrupts-extended = <&gpio3 8 IRQ_TYPE_LEVEL_HIGH>;
+ vwlan-supply = <&vwlan_fixed>;
+ };
+};
--
2.5.0
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 5+ messages in thread