[PATCH v3 0/5] ARM: dt: sunxi: Add Itead Ibox support

[PATCH v3 0/5] ARM: dt: sunxi: Add Itead Ibox support

[codekipper-Re5JQEeQqe8AvxtiuMwx3w]

From: Marcus Cooper <codekipper-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>

Hi All,

this patch series is an extension of the initial patch delivery for the
Itead Ibox as found here
https://groups.google.com/d/msg/linux-sunxi/GR_co3ObW8s/0BTPQljmAAAJ.

There seems to be a few Itead variants out there based on their A10/A20
core module and this patch series attempts to organise the device tree
files with some consideration that these variants may be added later.

I've also converted the A10 Itead Iteaduino dts to use these common files.
As I don't have this board to verify the changes I simply compared the
output of the fdtdump before and after applying these patches. The only
difference was the addition of codec support and a reduction to the dcdc2
max voltage.

BR,
CK

---
Changes since v2:
- removed duplicate naming
- moved enabling of some peripherals to board level.

Changes since v1:
- Added audio codec.
- Seperated into individual patches
- added Itead A10 core dtsi
- modified sun4i-a10-itead-iteaduino-plus.dts to use itead common core dtsi


Marcus Cooper (5):
  ARM: dts: sunxi: Add sunxi-itead-core-common.dtsi
  ARM: dts: sun7i: Add Itead A20 Core support
  ARM: dts: sun7i: Add Itead Ibox support
  ARM: dts: sun4i: Add Itead A10 Core support
  ARM: dts: sun4i: Itead Iteaduino to use common code

 arch/arm/boot/dts/Makefile                         |   1 +
 arch/arm/boot/dts/sun4i-a10-itead-core.dtsi        |  86 ++++++++++++++
 .../boot/dts/sun4i-a10-itead-iteaduino-plus.dts    |  93 +---------------
 arch/arm/boot/dts/sun7i-a20-itead-core.dtsi        |  87 +++++++++++++++
 arch/arm/boot/dts/sun7i-a20-itead-ibox.dts         | 124 +++++++++++++++++++++
 arch/arm/boot/dts/sunxi-itead-core-common.dtsi     |  99 ++++++++++++++++
 6 files changed, 399 insertions(+), 91 deletions(-)
 create mode 100644 arch/arm/boot/dts/sun4i-a10-itead-core.dtsi
 create mode 100644 arch/arm/boot/dts/sun7i-a20-itead-core.dtsi
 create mode 100644 arch/arm/boot/dts/sun7i-a20-itead-ibox.dts
 create mode 100644 arch/arm/boot/dts/sunxi-itead-core-common.dtsi

-- 
2.7.0

[PATCH v3 1/5] ARM: dts: sunxi: Add sunxi-itead-core-common.dtsi

[codekipper-Re5JQEeQqe8AvxtiuMwx3w]

From: Marcus Cooper <codekipper-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>

Itead have a core module board that can be populated with either
an Allwinner A10 or A20 SoC. This patch creates a common dtsi
which these boards can use.

Signed-off-by: Marcus Cooper <codekipper-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
---
 arch/arm/boot/dts/sunxi-itead-core-common.dtsi | 99 ++++++++++++++++++++++++++
 1 file changed, 99 insertions(+)
 create mode 100644 arch/arm/boot/dts/sunxi-itead-core-common.dtsi

diff --git a/arch/arm/boot/dts/sunxi-itead-core-common.dtsi b/arch/arm/boot/dts/sunxi-itead-core-common.dtsi
new file mode 100644
index 0000000..0074f7b
--- /dev/null
+++ b/arch/arm/boot/dts/sunxi-itead-core-common.dtsi
@@ -0,0 +1,99 @@
+/*
+ * Copyright 2015 - Marcus Cooper <codekipper-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins_a>;
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&reg_usb1_vbus {
+	status = "okay";
+};
+
+&reg_usb2_vbus {
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins_a>;
+	status = "okay";
+};
+
+&usbphy {
+	usb1_vbus-supply = <&reg_usb1_vbus>;
+	usb2_vbus-supply = <&reg_usb2_vbus>;
+	status = "okay";
+};
-- 
2.7.0

Re: [PATCH v3 1/5] ARM: dts: sunxi: Add sunxi-itead-core-common.dtsi

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 3495 bytes --]

On Thu, Jan 14, 2016 at 11:15:51AM +0100, codekipper-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org wrote:
> From: Marcus Cooper <codekipper-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> 
> Itead have a core module board that can be populated with either
> an Allwinner A10 or A20 SoC. This patch creates a common dtsi
> which these boards can use.
> 
> Signed-off-by: Marcus Cooper <codekipper-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> ---
>  arch/arm/boot/dts/sunxi-itead-core-common.dtsi | 99 ++++++++++++++++++++++++++
>  1 file changed, 99 insertions(+)
>  create mode 100644 arch/arm/boot/dts/sunxi-itead-core-common.dtsi
> 
> diff --git a/arch/arm/boot/dts/sunxi-itead-core-common.dtsi b/arch/arm/boot/dts/sunxi-itead-core-common.dtsi
> new file mode 100644
> index 0000000..0074f7b
> --- /dev/null
> +++ b/arch/arm/boot/dts/sunxi-itead-core-common.dtsi
> @@ -0,0 +1,99 @@
> +/*
> + * Copyright 2015 - Marcus Cooper <codekipper-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>

Didn't you take that code from the other itead board?

It seems wrong to remove the original author from the copyright list.

> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License as
> + *     published by the Free Software Foundation; either version 2 of the
> + *     License, or (at your option) any later version.
> + *
> + *     This file is distributed in the hope that it will be useful,
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use,
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +#include "sunxi-common-regulators.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/pinctrl/sun4i-a10.h>

You're not using any of these headers.

Thanks!
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[PATCH v3 2/5] ARM: dts: sun7i: Add Itead A20 Core support

[codekipper-Re5JQEeQqe8AvxtiuMwx3w]

From: Marcus Cooper <codekipper-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>

The A20 Itead Core module comes with 4GB NAND and 1GB DDR RAM. All of the
I/O interfaces are exposed via 4 groups of 2*30 1mm pitched female headers.

Signed-off-by: Marcus Cooper <codekipper-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
---
 arch/arm/boot/dts/sun7i-a20-itead-core.dtsi | 87 +++++++++++++++++++++++++++++
 1 file changed, 87 insertions(+)
 create mode 100644 arch/arm/boot/dts/sun7i-a20-itead-core.dtsi

diff --git a/arch/arm/boot/dts/sun7i-a20-itead-core.dtsi b/arch/arm/boot/dts/sun7i-a20-itead-core.dtsi
new file mode 100644
index 0000000..db8c0f9
--- /dev/null
+++ b/arch/arm/boot/dts/sun7i-a20-itead-core.dtsi
@@ -0,0 +1,87 @@
+/*
+ * Copyright 2015 - Marcus Cooper <codekipper-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "sun7i-a20.dtsi"
+#include "sunxi-itead-core-common.dtsi"
+
+&cpu0 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_a>;
+	status = "okay";
+
+	axp209: pmic@34 {
+		reg = <0x34>;
+		interrupt-parent = <&nmi_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+#include "axp209.dtsi"
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1000000>;
+	regulator-max-microvolt = <1400000>;
+	regulator-name = "vdd-cpu";
+};
+
+&reg_dcdc3 {
+	regulator-always-on;
+	regulator-min-microvolt = <1000000>;
+	regulator-max-microvolt = <1400000>;
+	regulator-name = "vdd-int-dll";
+};
+
+&reg_ldo1 {
+	regulator-name = "vdd-rtc";
+};
+
+&reg_ldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "avcc";
+};
-- 
2.7.0

[PATCH v3 3/5] ARM: dts: sun7i: Add Itead Ibox support

[codekipper-Re5JQEeQqe8AvxtiuMwx3w]

From: Marcus Cooper <codekipper-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>

The Itead Ibox is a multi board device based on the Allwinner A20 SoC.
It contains the A20 Itead Core module and a base board for the external
interfaces.

The core module comes with 4GB NAND and 1GB DDR RAM.

The base board to which the core board is connected provides 3 USB 2.0 Host
ports, 1 USB 2.0 OTG, 1 uSD slot, 10/100 Ethernet port, HDMI, IR receiver,
SPDIF and a 32-pin GPIO header. This header expands the features of core
board by exposing the VGA pins, audio In/Out pins, SATA, SPI, I2C, UARTS,
USB-OTG and power.

Signed-off-by: Marcus Cooper <codekipper-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
---
 arch/arm/boot/dts/Makefile                 |   1 +
 arch/arm/boot/dts/sun7i-a20-itead-ibox.dts | 124 +++++++++++++++++++++++++++++
 2 files changed, 125 insertions(+)
 create mode 100644 arch/arm/boot/dts/sun7i-a20-itead-ibox.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index da910b2..5c5e8f4 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -638,6 +638,7 @@ dtb-$(CONFIG_MACH_SUN7I) += \
 	sun7i-a20-cubieboard2.dtb \
 	sun7i-a20-cubietruck.dtb \
 	sun7i-a20-hummingbird.dtb \
+	sun7i-a20-itead-ibox.dtb \
 	sun7i-a20-i12-tvbox.dtb \
 	sun7i-a20-icnova-swac.dtb \
 	sun7i-a20-m3.dtb \
diff --git a/arch/arm/boot/dts/sun7i-a20-itead-ibox.dts b/arch/arm/boot/dts/sun7i-a20-itead-ibox.dts
new file mode 100644
index 0000000..66b8dec
--- /dev/null
+++ b/arch/arm/boot/dts/sun7i-a20-itead-ibox.dts
@@ -0,0 +1,124 @@
+/*
+ * Copyright 2015 - Marcus Cooper <codekipper-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun7i-a20-itead-core.dtsi"
+
+/ {
+	model = "Itead Ibox A20";
+	compatible = "itead,itead_ibox_a20", "allwinner,sun7i-a20";
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_pins_itead_core>;
+
+		green {
+			label = "itead_core:green:usr";
+			gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+
+		blue {
+			label = "itead_core:blue:usr";
+			gpios = <&pio 7 21 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+	};
+};
+
+&ahci {
+	target-supply = <&reg_ahci_5v>;
+	status = "okay";
+};
+
+&codec {
+	status = "okay";
+};
+
+&gmac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac_pins_mii_a>;
+	phy = <&phy1>;
+	phy-mode = "mii";
+	status = "okay";
+
+	phy1: ethernet-phy@1 {
+		reg = <1>;
+	};
+};
+
+&ir0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&ir0_rx_pins_a>;
+	status = "okay";
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+	cd-inverted;
+	status = "okay";
+};
+
+&pio {
+	led_pins_itead_core: led_pins@0 {
+		allwinner,pins = "PH20","PH21";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_20_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
+};
+
+&reg_ahci_5v {
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins_a>,
+		    <&spi0_cs0_pins_a>;
+	status = "okay";
+};
-- 
2.7.0

Re: [PATCH v3 3/5] ARM: dts: sun7i: Add Itead Ibox support

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 5788 bytes --]

Hi,

On Thu, Jan 14, 2016 at 11:15:53AM +0100, codekipper-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org wrote:
> From: Marcus Cooper <codekipper-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> 
> The Itead Ibox is a multi board device based on the Allwinner A20 SoC.
> It contains the A20 Itead Core module and a base board for the external
> interfaces.
> 
> The core module comes with 4GB NAND and 1GB DDR RAM.
> 
> The base board to which the core board is connected provides 3 USB 2.0 Host
> ports, 1 USB 2.0 OTG, 1 uSD slot, 10/100 Ethernet port, HDMI, IR receiver,
> SPDIF and a 32-pin GPIO header. This header expands the features of core
> board by exposing the VGA pins, audio In/Out pins, SATA, SPI, I2C, UARTS,
> USB-OTG and power.
> 
> Signed-off-by: Marcus Cooper <codekipper-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> ---
>  arch/arm/boot/dts/Makefile                 |   1 +
>  arch/arm/boot/dts/sun7i-a20-itead-ibox.dts | 124 +++++++++++++++++++++++++++++
>  2 files changed, 125 insertions(+)
>  create mode 100644 arch/arm/boot/dts/sun7i-a20-itead-ibox.dts
> 
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index da910b2..5c5e8f4 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -638,6 +638,7 @@ dtb-$(CONFIG_MACH_SUN7I) += \
>  	sun7i-a20-cubieboard2.dtb \
>  	sun7i-a20-cubietruck.dtb \
>  	sun7i-a20-hummingbird.dtb \
> +	sun7i-a20-itead-ibox.dtb \
>  	sun7i-a20-i12-tvbox.dtb \
>  	sun7i-a20-icnova-swac.dtb \
>  	sun7i-a20-m3.dtb \
> diff --git a/arch/arm/boot/dts/sun7i-a20-itead-ibox.dts b/arch/arm/boot/dts/sun7i-a20-itead-ibox.dts
> new file mode 100644
> index 0000000..66b8dec
> --- /dev/null
> +++ b/arch/arm/boot/dts/sun7i-a20-itead-ibox.dts
> @@ -0,0 +1,124 @@
> +/*
> + * Copyright 2015 - Marcus Cooper <codekipper-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License as
> + *     published by the Free Software Foundation; either version 2 of the
> + *     License, or (at your option) any later version.
> + *
> + *     This file is distributed in the hope that it will be useful,
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use,
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +#include "sun7i-a20-itead-core.dtsi"
> +
> +/ {
> +	model = "Itead Ibox A20";
> +	compatible = "itead,itead_ibox_a20", "allwinner,sun7i-a20";

Compatibles are using a dash (-) as a delimiter, not an underscore (_)

> +
> +	leds {
> +		compatible = "gpio-leds";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&led_pins_itead_core>;
> +
> +		green {
> +			label = "itead_core:green:usr";
> +			gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>;
> +			default-state = "on";
> +		};
> +
> +		blue {
> +			label = "itead_core:blue:usr";
> +			gpios = <&pio 7 21 GPIO_ACTIVE_HIGH>;
> +			default-state = "on";
> +		};
> +	};
> +};
> +
> +&ahci {
> +	target-supply = <&reg_ahci_5v>;
> +	status = "okay";
> +};
> +
> +&codec {
> +	status = "okay";
> +};
> +
> +&gmac {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&gmac_pins_mii_a>;
> +	phy = <&phy1>;
> +	phy-mode = "mii";
> +	status = "okay";
> +
> +	phy1: ethernet-phy@1 {
> +		reg = <1>;
> +	};
> +};
> +
> +&ir0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&ir0_rx_pins_a>;
> +	status = "okay";
> +};
> +
> +&mmc0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
> +	vmmc-supply = <&reg_vcc3v3>;
> +	bus-width = <4>;
> +	cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
> +	cd-inverted;
> +	status = "okay";
> +};
> +
> +&pio {
> +	led_pins_itead_core: led_pins@0 {
> +		allwinner,pins = "PH20","PH21";
> +		allwinner,function = "gpio_out";
> +		allwinner,drive = <SUN4I_PINCTRL_20_MA>;
> +		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> +	};
> +};
> +
> +&reg_ahci_5v {
> +	status = "okay";
> +};
> +
> +&spi0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&spi0_pins_a>,
> +		    <&spi0_cs0_pins_a>;
> +	status = "okay";

What device is connected to that bus?

Thanks,
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[PATCH v3 4/5] ARM: dts: sun4i: Add Itead A10 Core support

[codekipper-Re5JQEeQqe8AvxtiuMwx3w]

From: Marcus Cooper <codekipper-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>

The A10 Itead Core module comes with 4GB NAND and 1GB DDR RAM. All of the
I/O interfaces are exposed via 4 groups of 2*30 1mm pitched female headers.

Signed-off-by: Marcus Cooper <codekipper-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
---
 arch/arm/boot/dts/sun4i-a10-itead-core.dtsi | 86 +++++++++++++++++++++++++++++
 1 file changed, 86 insertions(+)
 create mode 100644 arch/arm/boot/dts/sun4i-a10-itead-core.dtsi

diff --git a/arch/arm/boot/dts/sun4i-a10-itead-core.dtsi b/arch/arm/boot/dts/sun4i-a10-itead-core.dtsi
new file mode 100644
index 0000000..97f653a
--- /dev/null
+++ b/arch/arm/boot/dts/sun4i-a10-itead-core.dtsi
@@ -0,0 +1,86 @@
+/*
+ * Copyright 2015 - Marcus Cooper <codekipper-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "sun4i-a10.dtsi"
+#include "sunxi-itead-core-common.dtsi"
+
+&cpu0 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_a>;
+	status = "okay";
+
+	axp209: pmic@34 {
+		reg = <0x34>;
+		interrupts = <0>;
+	};
+};
+
+#include "axp209.dtsi"
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1000000>;
+	regulator-max-microvolt = <1400000>;
+	regulator-name = "vdd-cpu";
+};
+
+&reg_dcdc3 {
+	regulator-always-on;
+	regulator-min-microvolt = <1000000>;
+	regulator-max-microvolt = <1400000>;
+	regulator-name = "vdd-int-dll";
+};
+
+&reg_ldo1 {
+	regulator-name = "vdd-rtc";
+};
+
+&reg_ldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "avcc";
+};
-- 
2.7.0

Re: [PATCH v3 4/5] ARM: dts: sun4i: Add Itead A10 Core support

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 4068 bytes --]

On Thu, Jan 14, 2016 at 11:15:54AM +0100, codekipper-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org wrote:
> From: Marcus Cooper <codekipper-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> 
> The A10 Itead Core module comes with 4GB NAND and 1GB DDR RAM. All of the
> I/O interfaces are exposed via 4 groups of 2*30 1mm pitched female headers.
> 
> Signed-off-by: Marcus Cooper <codekipper-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> ---
>  arch/arm/boot/dts/sun4i-a10-itead-core.dtsi | 86 +++++++++++++++++++++++++++++
>  1 file changed, 86 insertions(+)
>  create mode 100644 arch/arm/boot/dts/sun4i-a10-itead-core.dtsi
> 
> diff --git a/arch/arm/boot/dts/sun4i-a10-itead-core.dtsi b/arch/arm/boot/dts/sun4i-a10-itead-core.dtsi
> new file mode 100644
> index 0000000..97f653a
> --- /dev/null
> +++ b/arch/arm/boot/dts/sun4i-a10-itead-core.dtsi
> @@ -0,0 +1,86 @@
> +/*
> + * Copyright 2015 - Marcus Cooper <codekipper-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License as
> + *     published by the Free Software Foundation; either version 2 of the
> + *     License, or (at your option) any later version.
> + *
> + *     This file is distributed in the hope that it will be useful,
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use,
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +#include "sun4i-a10.dtsi"
> +#include "sunxi-itead-core-common.dtsi"
> +
> +&cpu0 {
> +	cpu-supply = <&reg_dcdc2>;
> +};
> +
> +&i2c0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2c0_pins_a>;
> +	status = "okay";
> +
> +	axp209: pmic@34 {
> +		reg = <0x34>;
> +		interrupts = <0>;
> +	};
> +};
> +
> +#include "axp209.dtsi"
> +
> +&reg_dcdc2 {
> +	regulator-always-on;
> +	regulator-min-microvolt = <1000000>;
> +	regulator-max-microvolt = <1400000>;
> +	regulator-name = "vdd-cpu";
> +};
> +
> +&reg_dcdc3 {
> +	regulator-always-on;
> +	regulator-min-microvolt = <1000000>;
> +	regulator-max-microvolt = <1400000>;
> +	regulator-name = "vdd-int-dll";
> +};
> +
> +&reg_ldo1 {
> +	regulator-name = "vdd-rtc";
> +};
> +
> +&reg_ldo2 {
> +	regulator-always-on;
> +	regulator-min-microvolt = <3000000>;
> +	regulator-max-microvolt = <3000000>;
> +	regulator-name = "avcc";
> +};
> -- 
> 2.7.0

Is there any difference with the A20 one?

Thanks,
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[linux-sunxi][PATCH v3 5/5] ARM: dts: sun4i: Itead Iteaduino to use common code

[codekipper-Re5JQEeQqe8AvxtiuMwx3w]

From: Marcus Cooper <codekipper-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>

Convert the Itead Iteaduino A10 to use the new common itead core dtsi.

Signed-off-by: Marcus Cooper <codekipper-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
---
 .../boot/dts/sun4i-a10-itead-iteaduino-plus.dts    | 93 +---------------------
 1 file changed, 2 insertions(+), 91 deletions(-)

diff --git a/arch/arm/boot/dts/sun4i-a10-itead-iteaduino-plus.dts b/arch/arm/boot/dts/sun4i-a10-itead-iteaduino-plus.dts
index 985e155..b84eca3 100644
--- a/arch/arm/boot/dts/sun4i-a10-itead-iteaduino-plus.dts
+++ b/arch/arm/boot/dts/sun4i-a10-itead-iteaduino-plus.dts
@@ -1,5 +1,6 @@
 /*
  * Copyright 2015 Josef Gajdusek <atx-MwjtXicnQwU@public.gmane.org>
+ * Copyright 2015 - Marcus Cooper <codekipper-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
  *
  * This file is dual-licensed: you can use it either under the terms
  * of the GPL or the X11 license, at your option. Note that this dual
@@ -41,23 +42,11 @@
  */
 
 /dts-v1/;
-#include "sun4i-a10.dtsi"
-#include "sunxi-common-regulators.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include "sun4i-a10-itead-core.dtsi"
 
 / {
 	model = "Iteaduino Plus A10";
 	compatible = "itead,iteaduino-plus-a10", "allwinner,sun4i-a10";
-
-	aliases {
-		serial0 = &uart0;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
 };
 
 &ahci {
@@ -65,18 +54,6 @@
 	status = "okay";
 };
 
-&cpu0 {
-	cpu-supply = <&reg_dcdc2>;
-};
-
-&ehci0 {
-	status = "okay";
-};
-
-&ehci1 {
-	status = "okay";
-};
-
 &emac {
 	pinctrl-names = "default";
 	pinctrl-0 = <&emac_pins_a>;
@@ -88,17 +65,6 @@
 	status = "okay";
 };
 
-&i2c0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c0_pins_a>;
-	status = "okay";
-
-	axp209: pmic@34 {
-		reg = <0x34>;
-		interrupts = <0>;
-	};
-};
-
 &i2c1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c1_pins_a>;
@@ -135,68 +101,13 @@
 	status = "okay";
 };
 
-&ohci0 {
-	status = "okay";
-};
-
-&ohci1 {
-	status = "okay";
-};
-
 &reg_ahci_5v {
 	status = "okay";
 };
 
-#include "axp209.dtsi"
-
-&reg_dcdc2 {
-	regulator-always-on;
-	regulator-min-microvolt = <1000000>;
-	regulator-max-microvolt = <1450000>;
-	regulator-name = "vdd-cpu";
-};
-
-&reg_dcdc3 {
-	regulator-always-on;
-	regulator-min-microvolt = <1000000>;
-	regulator-max-microvolt = <1400000>;
-	regulator-name = "vdd-int-dll";
-};
-
-&reg_ldo1 {
-	regulator-name = "vdd-rtc";
-};
-
-&reg_ldo2 {
-	regulator-always-on;
-	regulator-min-microvolt = <3000000>;
-	regulator-max-microvolt = <3000000>;
-	regulator-name = "avcc";
-};
-
-&reg_usb1_vbus {
-	status = "okay";
-};
-
-&reg_usb2_vbus {
-	status = "okay";
-};
-
 &spi0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&spi0_pins_a>,
 		    <&spi0_cs0_pins_a>;
 	status = "okay";
 };
-
-&uart0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
-	status = "okay";
-};
-
-&usbphy {
-	usb1_vbus-supply = <&reg_usb1_vbus>;
-	usb2_vbus-supply = <&reg_usb2_vbus>;
-	status = "okay";
-};
-- 
2.7.0

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html