From: John Stultz <john.stultz@linaro.org>
To: lkml <linux-kernel@vger.kernel.org>
Cc: John Stultz <john.stultz@linaro.org>,
Rob Herring <robh+dt@kernel.org>,
Arnd Bergmann <arnd.bergmann@linaro.org>,
Pawel Moll <pawel.moll@arm.com>,
Mark Rutland <mark.rutland@arm.com>,
Ian Campbell <ijc+devicetree@hellion.org.uk>,
Kumar Gala <galak@codeaurora.org>,
Andy Gross <agross@codeaurora.org>,
Russell King <linux@arm.linux.org.uk>,
Vinay Simha BN <simhavcs@gmail.com>,
Bjorn Andersson <bjorn.andersson@linaro.org>,
Stephen Boyd <stephen.boyd@linaro.org>,
linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org
Subject: [PATCH 2/2 v2] devicetree: Add DTS file to support the Nexus7 2013 (flo) device.
Date: Fri, 5 Feb 2016 11:21:05 -0800 [thread overview]
Message-ID: <1454700065-16256-1-git-send-email-john.stultz@linaro.org> (raw)
In-Reply-To: <CAL_JsqL1koD3OWM4-cqEOJUz-yuZuUeg1tmp6V39mPE0zrNPgg@mail.gmail.com>
This patch adds a dts file to support the Nexus7 2013
device. Its based off of the qcom-apq8064-ifc6410.dts
which is similar hardware.
Also includes some comments and context folded in
from Vinay Simha BN <simhavcs@gmail.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Arnd Bergmann <arnd.bergmann@linaro.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Andy Gross <agross@codeaurora.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Vinay Simha BN <simhavcs@gmail.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Stephen Boyd <stephen.boyd@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
---
v2: Fix dts/dtb typeo in makefile pointed out by Rob
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts | 276 +++++++++++++++++++++
2 files changed, 277 insertions(+)
create mode 100644 arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index a4a6d70..f6444be 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -524,6 +524,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8064-cm-qs600.dtb \
qcom-apq8064-ifc6410.dtb \
qcom-apq8064-sony-xperia-yuga.dtb \
+ qcom-apq8064-asus-nexus7-flo.dtb \
qcom-apq8074-dragonboard.dtb \
qcom-apq8084-ifc6540.dtb \
qcom-apq8084-mtp.dtb \
diff --git a/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts b/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts
new file mode 100644
index 0000000..c535b3f
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts
@@ -0,0 +1,276 @@
+#include "qcom-apq8064-v2.0.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+/ {
+ model = "Asus Nexus7(flo)";
+ compatible = "asus,nexus7-flo", "qcom,apq8064";
+
+ aliases {
+ serial0 = &gsbi7_serial;
+ serial1 = &gsbi6_serial;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ ext_3p3v: regulator-fixed@1 {
+ compatible = "regulator-fixed";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "ext_3p3v";
+ regulator-type = "voltage";
+ startup-delay-us = <0>;
+ gpio = <&tlmm_pinmux 77 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-boot-on;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ power {
+ label = "Power";
+ gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_POWER>;
+ gpio-key,wakeup;
+ };
+ volume_up {
+ label = "Volume Up";
+ gpios = <&pm8921_gpio 4 GPIO_ACTIVE_HIGH>;
+ linux,code = <KEY_VOLUMEUP>;
+ };
+ volume_down {
+ label = "Volume Down";
+ gpios = <&pm8921_gpio 38 GPIO_ACTIVE_HIGH>;
+ linux,code = <KEY_VOLUMEDOWN>;
+ };
+ };
+
+ soc {
+ rpm@108000 {
+ regulators {
+ vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
+ vin_lvs1_3_6-supply = <&pm8921_s4>;
+ vin_lvs4_5_7-supply = <&pm8921_s4>;
+
+
+ vdd_l24-supply = <&pm8921_s1>;
+ vdd_l25-supply = <&pm8921_s1>;
+ vin_lvs2-supply = <&pm8921_s1>;
+
+ vdd_l26-supply = <&pm8921_s7>;
+ vdd_l27-supply = <&pm8921_s7>;
+ vdd_l28-supply = <&pm8921_s7>;
+
+ vdd_ncp-supply = <&pm8921_l6>;
+
+ /* Buck SMPS */
+ s1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ qcom,switch-mode-frequency = <3200000>;
+ bias-pull-down;
+ };
+
+ /* msm otg HSUSB_VDDCX */
+ s3 {
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1150000>;
+ qcom,switch-mode-frequency = <4800000>;
+ };
+
+ /*
+ * msm_sdcc.1-sdc-vdd_io
+ * tabla2x-slim-CDC_VDDA_RX
+ * tabla2x-slim-CDC_VDDA_TX
+ * tabla2x-slim-CDC_VDD_CP
+ * tabla2x-slim-VDDIO_CDC
+ */
+ s4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ qcom,switch-mode-frequency = <3200000>;
+ regulator-always-on;
+ };
+
+ s7 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ qcom,switch-mode-frequency = <3200000>;
+ };
+
+ /* mipi_dsi.1-dsi1_pll_vdda */
+ l2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ /* msm_otg-HSUSB_3p3 */
+ l3 {
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3075000>;
+ bias-pull-down;
+ };
+
+ /* msm_otg-HSUSB_1p8 */
+ l4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ bias-pull-down;
+ };
+
+ /* msm_sdcc.1-sdc_vdd */
+ l5 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+ regulator-always-on;
+ bias-pull-down;
+ };
+
+ l6 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+ };
+
+ /* mipi_dsi.1-dsi1_avdd */
+ l11 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ bias-pull-down;
+ };
+
+ /* pwm_power for backlight */
+ l17 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3600000>;
+ bias-pull-down;
+ };
+
+ /* camera, qdsp6 */
+ l23 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ bias-pull-down;
+ };
+
+ /*
+ * tabla2x-slim-CDC_VDDA_A_1P2V
+ * tabla2x-slim-VDDD_CDC_D
+ */
+ l25 {
+ regulator-min-microvolt = <1250000>;
+ regulator-max-microvolt = <1250000>;
+ bias-pull-down;
+ };
+
+ lvs1 {
+ bias-pull-down;
+ };
+
+ lvs4 {
+ bias-pull-down;
+ };
+
+ lvs5 {
+ bias-pull-down;
+ };
+
+ lvs6 {
+ bias-pull-down;
+ };
+ /*
+ * mipi_dsi.1-dsi1_vddio
+ * pil_riva-pll_vdd
+ */
+ lvs7 {
+ bias-pull-down;
+ };
+ };
+ };
+
+ gsbi@16200000 {
+ status = "okay";
+ qcom,mode = <GSBI_PROT_I2C>;
+ i2c@16280000 {
+ status = "okay";
+ clock-frequency = <200000>;
+ pinctrl-0 = <&i2c3_pins>;
+ pinctrl-names = "default";
+
+ trackpad@10 {
+ compatible = "elan,ekth3500";
+ reg = <0x10>;
+ interrupt-parent = <&tlmm_pinmux>;
+ interrupts = <6 IRQ_TYPE_EDGE_FALLING>;
+ };
+ };
+ };
+
+
+ gsbi@12440000 {
+ status = "okay";
+ qcom,mode = <GSBI_PROT_I2C>;
+
+ i2c@12460000 {
+ status = "okay";
+ clock-frequency = <200000>;
+ pinctrl-0 = <&i2c1_pins>;
+ pinctrl-names = "default";
+
+ eeprom@52 {
+ compatible = "atmel,24c128";
+ reg = <0x52>;
+ pagesize = <32>;
+ };
+ };
+ };
+
+ gsbi@16500000 {
+ status = "ok";
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+
+ serial@16540000 {
+ status = "ok";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&gsbi6_uart_4pins>;
+ };
+ };
+
+ gsbi@16600000 {
+ status = "ok";
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+ serial@16640000 {
+ status = "ok";
+ };
+ };
+
+ /* OTG */
+ phy@12500000 {
+ status = "okay";
+ vddcx-supply = <&pm8921_s3>;
+ v3p3-supply = <&pm8921_l3>;
+ v1p8-supply = <&pm8921_l4>;
+ };
+
+ gadget@12500000 {
+ status = "okay";
+ };
+
+ /* OTG */
+ usb@12500000 {
+ status = "okay";
+ };
+
+ amba {
+ /* eMMC */
+ sdcc@12400000 {
+ status = "okay";
+ vmmc-supply = <&pm8921_l5>;
+ vqmmc-supply = <&pm8921_s4>;
+ };
+ };
+ };
+};
--
1.9.1
next prev parent reply other threads:[~2016-02-05 19:21 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-02-05 18:06 [PATCH 1/2] devicetree: qcom-apq8064.dtsi: Add i2c3 address-cells and size-cells values John Stultz
2016-02-05 18:06 ` [PATCH 2/2] devicetree: Add DTS file to support the Nexus7 2013 (flo) device John Stultz
2016-02-05 19:01 ` Rob Herring
[not found] ` <CAL_JsqL1koD3OWM4-cqEOJUz-yuZuUeg1tmp6V39mPE0zrNPgg-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2016-02-05 19:13 ` John Stultz
2016-02-05 19:21 ` John Stultz [this message]
2016-02-13 5:16 ` [PATCH 2/2 v2] " John Stultz
2016-02-13 6:06 ` Bjorn Andersson
2016-02-13 22:32 ` Linus Walleij
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1454700065-16256-1-git-send-email-john.stultz@linaro.org \
--to=john.stultz@linaro.org \
--cc=agross@codeaurora.org \
--cc=arnd.bergmann@linaro.org \
--cc=bjorn.andersson@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=galak@codeaurora.org \
--cc=ijc+devicetree@hellion.org.uk \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@arm.linux.org.uk \
--cc=mark.rutland@arm.com \
--cc=pawel.moll@arm.com \
--cc=robh+dt@kernel.org \
--cc=simhavcs@gmail.com \
--cc=stephen.boyd@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).