* [PATCH v3 10/10] dt-bindings: msm/hdmi: Add HDMI PHY bindings
[not found] <1456379565-15045-1-git-send-email-architt@codeaurora.org>
@ 2016-02-25 5:52 ` Archit Taneja
2016-03-02 17:41 ` Rob Herring
0 siblings, 1 reply; 2+ messages in thread
From: Archit Taneja @ 2016-02-25 5:52 UTC (permalink / raw)
To: robdclark; +Cc: arnd, devicetree, linux-arm-msm, dri-devel
Add HDMI PHY bindings. Update the example to use HDMI PHY.
Added a missing power-domains property in the HDMI core bindings. Also,
simplified HDMI TX's DT node name in the example.
Cc: devicetree@vger.kernel.org
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
---
.../devicetree/bindings/display/msm/hdmi.txt | 46 +++++++++++++++++++++-
1 file changed, 44 insertions(+), 2 deletions(-)
diff --git a/Documentation/devicetree/bindings/display/msm/hdmi.txt b/Documentation/devicetree/bindings/display/msm/hdmi.txt
index 379ee2e..b63f614 100644
--- a/Documentation/devicetree/bindings/display/msm/hdmi.txt
+++ b/Documentation/devicetree/bindings/display/msm/hdmi.txt
@@ -11,6 +11,7 @@ Required properties:
- reg: Physical base address and length of the controller's registers
- reg-names: "core_physical"
- interrupts: The interrupt signal from the hdmi block.
+- power-domains: Should be <&mmcc MDSS_GDSC>.
- clocks: device clocks
See ../clocks/clock-bindings.txt for details.
- qcom,hdmi-tx-ddc-clk-gpio: ddc clk pin
@@ -18,6 +19,8 @@ Required properties:
- qcom,hdmi-tx-hpd-gpio: hpd pin
- core-vdda-supply: phandle to supply regulator
- hdmi-mux-supply: phandle to mux regulator
+- phys: the phandle for the HDMI PHY device
+- phy-names: the name of the corresponding PHY device
Optional properties:
- qcom,hdmi-tx-mux-en-gpio: hdmi mux enable pin
@@ -27,15 +30,38 @@ Optional properties:
- pinctrl-0: the default pinctrl state (active)
- pinctrl-1: the "sleep" pinctrl state
+HDMI PHY:
+Required properties:
+- compatible: Could be the following
+ * "qcom,hdmi-phy-8660"
+ * "qcom,hdmi-phy-8960"
+ * "qcom,hdmi-phy-8974"
+ * "qcom,hdmi-phy-8084"
+ * "qcom,hdmi-phy-8996"
+- #phy-cells: Number of cells in a PHY specifier; Should be 0.
+- reg: Physical base address and length of the registers of the PHY sub blocks.
+- reg-names: The names of register regions. The following regions are required:
+ * "hdmi_phy"
+ * "hdmi_pll"
+ For HDMI PHY on msm8996, these additional register regions are required:
+ * "hdmi_tx_l0"
+ * "hdmi_tx_l1"
+ * "hdmi_tx_l3"
+ * "hdmi_tx_l4"
+- power-domains: Should be <&mmcc MDSS_GDSC>.
+- clocks: device clocks
+ See Documentation/devicetree/bindings/clocks/clock-bindings.txt for details.
+- core-vdda-supply: phandle to vdda regulator device node
+
Example:
/ {
...
- hdmi: qcom,hdmi-tx-8960@4a00000 {
+ hdmi: hdmi@4a00000 {
compatible = "qcom,hdmi-tx-8960";
reg-names = "core_physical";
- reg = <0x04a00000 0x1000>;
+ reg = <0x04a00000 0x2f0>;
interrupts = <GIC_SPI 79 0>;
power-domains = <&mmcc MDSS_GDSC>;
clock-names =
@@ -54,5 +80,21 @@ Example:
pinctrl-names = "default", "sleep";
pinctrl-0 = <&hpd_active &ddc_active &cec_active>;
pinctrl-1 = <&hpd_suspend &ddc_suspend &cec_suspend>;
+
+ phys = <&hdmi_phy>;
+ phy-names = "hdmi_phy";
+ };
+
+ hdmi_phy: phy@4a00400 {
+ compatible = "qcom,hdmi-phy-8960";
+ reg-names = "hdmi_phy",
+ "hdmi_pll";
+ reg = <0x4a00400 0x60>,
+ <0x4a00500 0x100>;
+ #phy-cells = <0>;
+ power-domains = <&mmcc MDSS_GDSC>;
+ clock-names = "slave_iface_clk";
+ clocks = <&mmcc HDMI_S_AHB_CLK>;
+ core-vdda-supply = <&pm8921_hdmi_mvs>;
};
};
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 2+ messages in thread