From: kernel-TqfNSX0MhmxHKSADF0wUEw@public.gmane.org
To: Rob Herring <robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>,
Stephen Warren <swarren-3lzwWm7+Weoh9ZMKESR00Q@public.gmane.org>,
Lee Jones <lee-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>,
Eric Anholt <eric-WhKQ6XTQaPysTnJN9+BGXg@public.gmane.org>,
Vinod Koul <vinod.koul-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>,
devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
linux-rpi-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org,
dmaengine-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Cc: Martin Sperl <kernel-TqfNSX0MhmxHKSADF0wUEw@public.gmane.org>
Subject: [PATCH v3 02/11] dmaengine: bcm2835: remove unnecessary masking of dma channels
Date: Sat, 5 Mar 2016 10:52:13 +0000 [thread overview]
Message-ID: <1457175142-28665-3-git-send-email-kernel@martin.sperl.org> (raw)
In-Reply-To: <1457175142-28665-1-git-send-email-kernel-TqfNSX0MhmxHKSADF0wUEw@public.gmane.org>
From: Martin Sperl <kernel-TqfNSX0MhmxHKSADF0wUEw@public.gmane.org>
The original patch contained 3 dma channels that were masked out.
These - as far as research and discussions show - are a
artefacts remaining from the downstream legacy dma-api.
Right now down-stream still includes a legacy api used only
in a single (downstream only) driver (bcm2708_fb) that requires
2D DMA for speedup (DMA-channel 0).
Formerly the sd-card support driver also was using this legacy
api (DMA-channel 2), but since has been moved over to use
dmaengine directly.
The DMA-channel 3 is already masked out in the devicetree in
the default property "brcm,dma-channel-mask = <0x7f35>;"
So we can remove the whole masking of DMA channels.
Signed-off-by: Martin Sperl <kernel-TqfNSX0MhmxHKSADF0wUEw@public.gmane.org>
Reviewed-by: Eric Anholt <eric-WhKQ6XTQaPysTnJN9+BGXg@public.gmane.org>
---
drivers/dma/bcm2835-dma.c | 9 ---------
1 file changed, 9 deletions(-)
diff --git a/drivers/dma/bcm2835-dma.c b/drivers/dma/bcm2835-dma.c
index 2d72fe8..e4ca980 100644
--- a/drivers/dma/bcm2835-dma.c
+++ b/drivers/dma/bcm2835-dma.c
@@ -123,9 +123,6 @@ struct bcm2835_desc {
#define BCM2835_DMA_DATA_TYPE_S32 4
#define BCM2835_DMA_DATA_TYPE_S128 16
-#define BCM2835_DMA_BULK_MASK BIT(0)
-#define BCM2835_DMA_FIQ_MASK (BIT(2) | BIT(3))
-
/* Valid only for channels 0 - 14, 15 has its own base address */
#define BCM2835_DMA_CHAN(n) ((n) << 8) /* Base address */
#define BCM2835_DMA_CHANIO(base, n) ((base) + BCM2835_DMA_CHAN(n))
@@ -641,12 +638,6 @@ static int bcm2835_dma_probe(struct platform_device *pdev)
goto err_no_dma;
}
- /*
- * Do not use the FIQ and BULK channels,
- * because they are used by the GPU.
- */
- chans_available &= ~(BCM2835_DMA_FIQ_MASK | BCM2835_DMA_BULK_MASK);
-
for (i = 0; i < pdev->num_resources; i++) {
irq = platform_get_irq(pdev, i);
if (irq < 0)
--
2.1.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
next prev parent reply other threads:[~2016-03-05 10:52 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-03-05 10:52 [PATCH v3 00/11] dmaengine: bcm2835: bugfix + enhancement of driver kernel-TqfNSX0MhmxHKSADF0wUEw
[not found] ` <1457175142-28665-1-git-send-email-kernel-TqfNSX0MhmxHKSADF0wUEw@public.gmane.org>
2016-03-05 10:52 ` [PATCH v3 01/11] dmaengine: bcm2835: set residue_granularity field kernel-TqfNSX0MhmxHKSADF0wUEw
2016-03-05 10:52 ` kernel-TqfNSX0MhmxHKSADF0wUEw [this message]
2016-03-05 10:52 ` [PATCH v3 03/11] dmaengine: bcm2835: use shared interrupt for channel 11 to 14 kernel-TqfNSX0MhmxHKSADF0wUEw
2016-03-05 10:52 ` [PATCH v3 04/11] ARM: bcm2835: dt: add bindings for shared interrupt properties kernel-TqfNSX0MhmxHKSADF0wUEw
[not found] ` <1457175142-28665-5-git-send-email-kernel-TqfNSX0MhmxHKSADF0wUEw@public.gmane.org>
2016-03-07 23:24 ` Eric Anholt
[not found] ` <87fuw1yipi.fsf-omZaPlIz5HhaEpDpdNBo/KxOck334EZe@public.gmane.org>
2016-03-08 11:23 ` Martin Sperl
[not found] ` <3503D512-7E9C-46E8-91C7-CAD828DD48D1-TqfNSX0MhmxHKSADF0wUEw@public.gmane.org>
2016-03-11 5:53 ` Vinod Koul
2016-03-10 8:57 ` Mark Rutland
2016-03-11 8:51 ` Martin Sperl
[not found] ` <E60A6B56-0F3F-465C-8BF7-59EF35D41070-TqfNSX0MhmxHKSADF0wUEw@public.gmane.org>
2016-03-22 9:23 ` Martin Sperl
[not found] ` <56F10F21.9020709-TqfNSX0MhmxHKSADF0wUEw@public.gmane.org>
2016-03-22 10:24 ` Mark Rutland
2016-03-05 10:52 ` [PATCH v3 05/11] dmaengine: bcm2835: add additional defines for DMA-registers kernel-TqfNSX0MhmxHKSADF0wUEw
2016-03-05 10:52 ` [PATCH v3 06/11] dmaengine: bcm2835: move cyclic member from bcm2835_chan into bcm2835_desc kernel-TqfNSX0MhmxHKSADF0wUEw
2016-03-05 10:52 ` [PATCH v3 07/11] dmaengine: bcm2835: move controlblock chain generation into separate method kernel-TqfNSX0MhmxHKSADF0wUEw
2016-03-05 10:52 ` [PATCH v3 08/11] dmaengine: bcm2835: limit max length based on channel type kernel-TqfNSX0MhmxHKSADF0wUEw
2016-03-05 10:52 ` [PATCH v3 09/11] dmaengine: bcm2835: add slave_sg support to bcm2835-dma kernel-TqfNSX0MhmxHKSADF0wUEw
2016-03-05 10:52 ` [PATCH v3 10/11] dmaengine: bcm2835: add dma_memcopy " kernel-TqfNSX0MhmxHKSADF0wUEw
2016-03-05 10:52 ` [PATCH v3 11/11] dmaengine: bcm2835: expose dma registers via debugfs kernel-TqfNSX0MhmxHKSADF0wUEw
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1457175142-28665-3-git-send-email-kernel@martin.sperl.org \
--to=kernel-tqfnsx0mhmxhksadf0wuew@public.gmane.org \
--cc=devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=dmaengine-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=eric-WhKQ6XTQaPysTnJN9+BGXg@public.gmane.org \
--cc=lee-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org \
--cc=linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org \
--cc=linux-rpi-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org \
--cc=robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org \
--cc=swarren-3lzwWm7+Weoh9ZMKESR00Q@public.gmane.org \
--cc=vinod.koul-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).