[PATCH] ARM: dts: sun8i: Base Orange Pi Plus dts on the Orange Pi 2 dts

[Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>]

The Orange Pi Plus really is an Orange Pi 2 extended with:
1) A sata <-> usb bridge connected to ehci3
2) An eMMC on mmc2
3) An external gigabit ethernet phy instead of the integrated 100Mbit phy

This commit changes the dts to reflect this by making it include
the Orange Pi 2 dts and then adding the extra bits.

Note that the difference in ethernet phy is not taken into account
because we do not have an ethernet driver for the H3 yet.

Signed-off-by: Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
---
 arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts | 136 +--------------------------
 1 file changed, 2 insertions(+), 134 deletions(-)

diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts
index 94f8b0b..b0cb417 100644
--- a/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts
+++ b/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts
@@ -40,61 +40,13 @@
  *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
-/dts-v1/;
-#include "sun8i-h3.dtsi"
-#include "sunxi-common-regulators.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
+/* The Orange Pi Plus is an extended version of the Orange Pi 2 */
+#include "sun8i-h3-orangepi-2.dts"
 
 / {
 	model = "Xunlong Orange Pi Plus";
 	compatible = "xunlong,orangepi-plus", "allwinner,sun8i-h3";
 
-	aliases {
-		serial0 = &uart0;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&leds_opc>, <&leds_r_opc>;
-
-		status_led {
-			label = "orangepi-plus:red:status";
-			gpios = <&pio 0 15 GPIO_ACTIVE_HIGH>;
-		};
-
-		pwr_led {
-			label = "orangepi-plus:green:pwr";
-			gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
-			default-state = "on";
-		};
-	};
-
-	r_gpio_keys {
-		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&sw_r_opc>;
-
-		sw2 {
-			label = "sw2";
-			linux,code = <BTN_1>;
-			gpios = <&r_pio 0 4 GPIO_ACTIVE_LOW>;
-		};
-
-		sw4 {
-			label = "sw4";
-			linux,code = <BTN_0>;
-			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
-		};
-	};
-
 	reg_usb3_vbus: usb3-vbus {
 		compatible = "regulator-fixed";
 		pinctrl-names = "default";
@@ -106,49 +58,12 @@
 		enable-active-high;
 		gpio = <&pio 6 11 GPIO_ACTIVE_HIGH>;
 	};
-
-	wifi_pwrseq: wifi_pwrseq {
-		compatible = "mmc-pwrseq-simple";
-		pinctrl-names = "default";
-		pinctrl-0 = <&wifi_pwrseq_pin_orangepi>;
-		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 WIFI_EN */
-	};
-};
-
-&ehci1 {
-	status = "okay";
 };
 
 &ehci3 {
 	status = "okay";
 };
 
-&ir {
-	pinctrl-names = "default";
-	pinctrl-0 = <&ir_pins_a>;
-	status = "okay";
-};
-
-&mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
-	vmmc-supply = <&reg_vcc3v3>;
-	bus-width = <4>;
-	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
-	cd-inverted;
-	status = "okay";
-};
-
-&mmc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc1_pins_a>;
-	vmmc-supply = <&reg_vcc3v3>;
-	mmc-pwrseq = <&wifi_pwrseq>;
-	bus-width = <4>;
-	non-removable;
-	status = "okay";
-};
-
 &mmc2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc2_8bit_pins>;
@@ -167,13 +82,6 @@
 };
 
 &pio {
-	leds_opc: led_pins@0 {
-		allwinner,pins = "PA15";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-	};
-
 	usb3_vbus_pin_a: usb3_vbus_pin@0 {
 		allwinner,pins = "PG11";
 		allwinner,function = "gpio_out";
@@ -182,46 +90,6 @@
 	};
 };
 
-&r_pio {
-	leds_r_opc: led_pins@0 {
-		allwinner,pins = "PL10";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-	};
-
-	sw_r_opc: key_pins@0 {
-		allwinner,pins = "PL3", "PL4";
-		allwinner,function = "gpio_in";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-	};
-
-	wifi_pwrseq_pin_orangepi: wifi_pwrseq_pin@0 {
-		allwinner,pins = "PL7";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-	};
-};
-
-&reg_usb1_vbus {
-	gpio = <&pio 6 13 GPIO_ACTIVE_HIGH>;
-	status = "okay";
-};
-
-&uart0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
-	status = "okay";
-};
-
-&usb1_vbus_pin_a {
-	allwinner,pins = "PG13";
-};
-
 &usbphy {
-	usb1_vbus-supply = <&reg_usb1_vbus>;
 	usb3_vbus-supply = <&reg_usb3_vbus>;
-	status = "okay";
 };
-- 
2.7.3

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html