[PATCH resend v2 6/9] ARM: dts: sun9i: a80-optimus: Add AXP809 PMIC device node and regulators

[Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>]

The AXP809 PMIC is the primary PMIC. It provides various supply voltages
for the SoC and other peripherals. The PMIC's interrupt line is
connected to NMI pin of the SoC.

Signed-off-by: Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
---
 arch/arm/boot/dts/sun9i-a80-optimus.dts | 131 +++++++++++++++++++++++++++++++-
 1 file changed, 129 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/sun9i-a80-optimus.dts b/arch/arm/boot/dts/sun9i-a80-optimus.dts
index d7a20d92b114..6cfc02194035 100644
--- a/arch/arm/boot/dts/sun9i-a80-optimus.dts
+++ b/arch/arm/boot/dts/sun9i-a80-optimus.dts
@@ -150,7 +150,7 @@
 &mmc0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins>, <&mmc0_cd_pin_optimus>;
-	vmmc-supply = <&reg_vcc3v0>;
+	vmmc-supply = <&reg_dcdc1>;
 	bus-width = <4>;
 	cd-gpios = <&pio 7 18 GPIO_ACTIVE_HIGH>; /* PH8 */
 	cd-inverted;
@@ -160,7 +160,7 @@
 &mmc2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc2_8bit_pins>;
-	vmmc-supply = <&reg_vcc3v0>;
+	vmmc-supply = <&reg_dcdc1>;
 	bus-width = <8>;
 	non-removable;
 	cap-mmc-hw-reset;
@@ -193,8 +193,135 @@
 
 &r_rsb {
 	status = "okay";
+
+	axp809: pmic@3a3 {
+		reg = <0x3a3>;
+		interrupt-parent = <&nmi_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+
+		regulators {
+			reg_aldo1: aldo1 {
+				/*
+				 * TODO: This should be handled by the
+				 * USB PHY driver.
+				 */
+				regulator-always-on;
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-name = "vcc33-usbh";
+			};
+
+			reg_aldo2: aldo2 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc-pb-io-cam";
+			};
+
+			aldo3 {
+				/* unused */
+			};
+
+			reg_dc5ldo: dc5ldo {
+				regulator-always-on;
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-name = "vdd-cpus-09-usbh";
+			};
+
+			reg_dcdc1: dcdc1 {
+				regulator-always-on;
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-name = "vcc-3v";
+			};
+
+			reg_dcdc2: dcdc2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-name = "vdd-gpu";
+			};
+
+			reg_dcdc3: dcdc3 {
+				regulator-always-on;
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-name = "vdd-cpua";
+			};
+
+			reg_dcdc4: dcdc4 {
+				regulator-always-on;
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-name = "vdd-sys-usb0-hdmi";
+			};
+
+			reg_dcdc5: dcdc5 {
+				regulator-always-on;
+				regulator-min-microvolt = <1425000>;
+				regulator-max-microvolt = <1575000>;
+				regulator-name = "vcc-dram";
+			};
+
+			reg_dldo1: dldo1 {
+				/*
+				 * The WiFi chip supports a wide range
+				 * (3.0 ~ 4.8V) of voltages, and so does
+				 * this regulator (3.0 ~ 4.2V), but
+				 * Allwinner SDK always sets it to 3.3V.
+				 */
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc-wifi";
+			};
+
+			reg_dldo2: dldo2 {
+				regulator-always-on;
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-name = "vcc-pl";
+			};
+
+			reg_eldo1: eldo1 {
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-name = "vcc-dvdd-cam";
+			};
+
+			reg_eldo2: eldo2 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc-pe";
+			};
+
+			reg_eldo3: eldo3 {
+				regulator-always-on;
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-name = "vcc-pm-codec-io1";
+			};
+
+			reg_ldo_io0: ldo_io0 {
+				regulator-always-on;
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-name = "vcc-pg";
+			};
+
+			reg_ldo_io1: ldo_io1 {
+				regulator-min-microvolt = <2500000>;
+				regulator-max-microvolt = <2500000>;
+				regulator-name = "vcc-pa-gmac-2v5";
+			};
+
+			reg_rtc_ldo: rtc_ldo {
+				regulator-name = "vcc-rtc-vdd1v8-io";
+			};
+		};
+	};
 };
 
+#include "axp809.dtsi"
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pins_a>;
-- 
2.7.0